Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamic Timing Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Evaluation of MOSTAS computer code for predicting dynamic loads in two-bladed wind turbines

Calculated dynamic blade loads are compared with measured loads over a range of yaw stiffnesses of the DOE/NASA Mod-0 wind turbine to evaluate the performance of two versions of the MOSTAS computer code. The first version uses a time-averaged coefficient approximation in conjunction with a multiblade coordinate transformation for two-bladed rotors to solve the equations of motion by standard eigenanalysis. The results obtained with this approximate analysis do not agree with dynamic blade load amplifications at or close to resonance conditions. The results of the second version, which accounts for periodic coefficients while solving the equations by a time history integration, compare well with the measured data.

Kaza, K. R. V.↗

Aeromechanics Analysis of a Distortion-Tolerant Fan with Boundary Layer Ingestion

A propulsion system with Boundary Layer Ingestion (BLI) has the potential to significantly reduce aircraft engine fuel burn. But a critical challenge is to design a fan that can operate continuously with a persistent BLI distortion without aeromechanical failure -- flutter or high cycle fatigue due to forced response. High-fidelity computational aeromechanics analysis can be very valuable to support the design of a fan that has satisfactory aeromechanic characteristics and good aerodynamic performance and operability. Detailed aeromechanics analyses together with careful monitoring of the test article is necessary to avoid unexpected problems or failures during testing. In the present work, an aeromechanics analysis based on a three-dimensional, time-accurate, Reynolds-averaged Navier-Stokes computational fluid dynamics code is used to study the performance and aeromechanical characteristics of the fan in both circumferentially-uniform and circumferentially-varying distorted flows. Pre-test aeromechanics analyses are used to prepare for the wind tunnel test and comparisons are made with measured blade vibration data after the test. The analysis shows that the fan has low levels of aerodynamic damping at various operating conditions examined. In the test, the fan remained free of flutter except at one near-stall operating condition. Analysis could not be performed at this low mass flow rate operating condition since it fell beyond the limit of numerical stability of the analysis code. The measured resonant forced response at a specific low-response crossing indicated that the analysis under-predicted this response and work is in progress to understand possible sources of differences and to analyze other larger resonant responses. Follow-on work is also planned with a coupled inlet-fan aeromechanics analysis that will more accurately represent the interactions between the fan and BLI distortion.

Propulsion Aeroelasticity↗

Inelastic and Dynamic Fracture and Stress Analyses

Large deformation inelastic stress analysis and inelastic and dynamic crack propagation research work is summarized. The salient topics of interest in engine structure analysis that are discussed herein include: (1) a path-independent integral (T) in inelastic fracture mechanics, (2) analysis of dynamic crack propagation, (3) generalization of constitutive relations of inelasticity for finite deformations , (4) complementary energy approaches in inelastic analyses, and (5) objectivity of time integration schemes in inelastic stress analysis.

Atluri, S. N.↗

Group implicit concurrent algorithms in nonlinear structural dynamics

During the 70's and 80's, considerable effort was devoted to developing efficient and reliable time stepping procedures for transient structural analysis. Mathematically, the equations governing this type of problems are generally stiff, i.e., they exhibit a wide spectrum in the linear range. The algorithms best suited to this type of applications are those which accurately integrate the low frequency content of the response without necessitating the resolution of the high frequency modes. This means that the algorithms must be unconditionally stable, which in turn rules out explicit integration. The most exciting possibility in the algorithms development area in recent years has been the advent of parallel computers with multiprocessing capabilities. So, this work is mainly concerned with the development of parallel algorithms in the area of structural dynamics. A primary objective is to devise unconditionally stable and accurate time stepping procedures which lend themselves to an efficient implementation in concurrent machines. Some features of the new computer architecture are summarized. A brief survey of current efforts in the area is presented. A new class of concurrent procedures, or Group Implicit algorithms is introduced and analyzed. The numerical simulation shows that GI algorithms hold considerable promise for application in coarse grain as well as medium grain parallel computers.

Ortiz, M.↗

Real-Time Parameter Estimation in the Frequency Domain

A method for real-time estimation of parameters in a linear dynamic state-space model was developed and studied. The application is aircraft dynamic model parameter estimation from measured data in flight. Equation error in the frequency domain was used with a recursive Fourier transform for the real-time data analysis. Linear and nonlinear simulation examples and flight test data from the F-18 High Alpha Research Vehicle were used to demonstrate that the technique produces accurate model parameter estimates with appropriate error bounds. Parameter estimates converged in less than one cycle of the dominant dynamic mode, using no a priori information, with control surface inputs measured in flight during ordinary piloted maneuvers. The real-time parameter estimation method has low computational requirements and could be implemented

Morelli, Eugene A.↗

Revealing meso-structure dynamics in additive manufacturing of energy storage via operando coherent X-ray scattering

3D printing is an emerging technology for the fabrication of energy storage devices, offering advantages over traditional manufacturing methods. However, optimization and design of such devices requires an understanding of the meso-structure formation during the 3D printing process. This study utilizes operando coherent X-ray scattering, X-ray Photon Correlation Spectroscopy (XPCS), to study the spatiotemporally-resolved far-from-equilibrium dynamics during direct ink writing 3D printing. Here, Lithium Titanate (LTO) based ink is prepared and rheologically tested for its shear-thinning properties. Two-time intensity-intensity functions are calculated to be used in subsequent quantitative analysis, which allows for an overall characterization of the dynamics, description of an initial fast decorrelation and identification of sudden rearrangements of subdomains of the sample. The results show the dynamics to be anisotropic, spatiotemporally heterogenous and marked by distinct rearrangement events, all of which impact the electrochemical performance of energy storage devices. The studied 3D printing ink is used to fabricate electrodes which are then electrochemically tested, showing good performance in cycling and retaining structural integrity. This work furthers the understanding of the far-from-equilibrium material dynamics during 3D printing, giving quantitative characterization of this process, and highlights aspects of structure formation relevant to the electrochemical performance of the resultant energy storage device.

36 MATERIALS SCIENCE↗

Axisymmetric elastodynamic response from normal and radial impact of layered composites with embedded penny-shaped cracks

A method is developed for the dynamic stress analysis of a layered composite containing an embedded penny-shaped crack and subjected to normal and radial impact. Quantitatively, the time-dependent stresses near the crack border can be described by the dynamic stress intensity factors. Their magnitude depends on time, on the material properties of the composite and on the relative size of the crack compared to the composite local geometry. Results obtained show that, for the same material properties and geometry of the composite, the dynamic stress intensity factors for an embedded (penny-shaped) crack reach their peak values within a shorter period of time and with a lower magnitude than the corresponding dynamic stress factors for a through-crack.

Sih, G. C.↗

Seismic analysis of the large 70-meter antenna. Part 2: General dynamic response and a seismic safety check

An extensive dynamic analysis for the new JPL 70-meter antenna structure is presented. Analytical procedures are based on the normal mode decomposition which include dumping and special forcing functions. The dynamic response can be obtained for any arbitrarily selected point on the structure. A new computer program for computing the time-dependent, resultant structural displacement, summing the effects of all participating modes, was developed also. Program compatibility with natural frequency analysis output was verified. The program was applied to the JPL 70-meter antenna structure and the dynamic response for several specially selected points was computed. Seismic analysis of structures, a special application of the general dynamic analysis, is based also on the normal modal decomposition. Strength specification of the antenna, with respect to the earthquake excitation, is done by using the common response spectra. The results indicated basically a safe design under an assumed 5% or more damping coefficient. However, for the antenna located at Goldstone, with more active seismic environment, this study strongly recommends and experimental program that determines the true damping coefficient for a more reliable safety check.

Kiedron, K.↗

CLVTOPS Liftoff and Separation Analysis Validation Using Ares I-X Flight Data

CLVTOPS is a multi-body time domain flight dynamics simulation tool developed by NASA s Marshall Space Flight Center (MSFC) for a space launch vehicle and is based on the TREETOPS simulation tool. CLVTOPS is currently used to simulate the flight dynamics and separation/jettison events of the Ares I launch vehicle including liftoff and staging separation. In order for CLVTOPS to become an accredited tool, validation against other independent simulations and real world data is needed. The launch of the Ares I-X vehicle (first Ares I test flight) on October 28, 2009 presented a great opportunity to provide validation evidence for CLVTOPS. In order to simulate the Ares I-X flight, specific models were implemented into CLVTOPS. These models include the flight day environment, reconstructed thrust, reconstructed mass properties, aerodynamics, and the Ares I-X guidance, navigation and control models. The resulting simulation output was compared to Ares I-X flight data. During the liftoff region of flight, trajectory states from the simulation and flight data were compared. The CLVTOPS results were used to make a semi-transparent animation of the vehicle that was overlaid directly on top of the flight video to provide a qualitative measure of the agreement between the simulation and the actual flight. During ascent, the trajectory states of the vehicle were compared with flight data. For the stage separation event, the trajectory states of the two stages were compared to available flight data. Since no quantitative rotational state data for the upper stage was available, the CLVTOPS results were used to make an animation of the two stages to show a side-by-side comparison with flight video. All of the comparisons between CLVTOPS and the flight data show good agreement. This paper documents comparisons between CLVTOPS and Ares I-X flight data which serve as validation evidence for the eventual accreditation of CLVTOPS.

Burger, Ben↗

Multi-device study of temporal characteristics of magnetohydrodynamic modes initiating disruptions

Disruptions in tokamaks are often preceded by magnetohydrodynamic (MHD) instabilities that can rotate or become locked to the wall. Measurements from magnetic diagnostics in the presence of MHD mode precursors to disruptions can yield potentially valuable input to the plasma control system, with a view to disruption avoidance, prediction and mitigation. This report presents an exploratory analysis of the growth of MHD modes and corresponding time scales on the basis of magnetic measurements in multiple tokamaks. To this end, a database was compiled using disruptive discharges from COMPASS, ASDEX Upgrade, DIII-D and JET, manually classified according to disruption root cause, and characterized by a great diversity of operational conditions and mode dynamics. The typical time during which a mode can be detected using saddle coils and the duration of the locked mode phase in the database both extend over several orders of magnitude, but generally the time scales increase with plasma size. Several additional factors are discussed that can influence these durations, including the disruption root cause. A scaling law for the locked phase duration was estimated, yielding predictions toward ITER of the order of hundreds of milliseconds or even seconds. In addition, a scaling law for the mode amplitude at the disruption onset, proposed earlier by de Vries et al. (2016), is applied to the database, and its predictive capabilities are assessed. Despite significant uncertainty on the predictions from both scaling laws, encouraging trends are observed of the fraction of disruptions that may be detected with sufficient warning time to allow mitigation or even avoidance, based solely on observations of MHD mode dynamics. When combined with similar analysis of measurements from diagnostics that are sensitive to other disruption precursors, our analysis methods and results may contribute to the reliability, robustness and generalization of disruption warning schemes for ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Practical aspects of on-orbit modal identification using free-decay data

Future large space structures such as Space Station Freedom can be tested as a total structure on Earth. Size, zero g design, and the existing atmosphere conflict with traditional structural dynamic testing. On-orbit modal identification will become necessary. Practical aspects of performing such tests using time domain analysis of free decay data are discussed. The effects of environmental constraints, structural characteristics, and excitation and sensing are reviewed. A recent laboratory application and sensing are reviewed. In this test, an on-orbit experiment is simulated using free decay data and a limited number of excitation and measurement points. The test article is dynamically similar to the truss/solar arrays of Space Station. The identified modal parameters from this simulation correlate well, though not uniquely, with those obtained in a complete modal survey. Practical difficulties in performing the correlation are illustrated. Model parameters are identified with the Eigensystem Realization Algorithm.

Schenk, Axel↗

"Layers in the Equatorial Mesosphere, Motions and Aerosol Rocket and Radar Study (LEMMA)"

Our role in the LEMMA rocket and radar measurement program had several components corresponding to the various phases of the research effort. Our initial efforts focused on definition of the experimental configuration and measurement requirements following the decision to move the experiment to Kwajalein. At this stage of the research, the PI of this subtask consulted with the project PI, Dr. Gerald Lehmacher, and other participants in defining the atmospheric conditions that would allow optimal measurements and the radar modes that would best characterize the structures we hoped to observe. This proved to be a challenge, as the ALTAIR radar, despite its substantial capabilities, did not have a representative suite of software control and analysis capabilities. Once the experiment and timing were defined, our role shifted to numerical characterization of potential radar backscatter and in situ turbulence signatures accompanying various dynamical processes. Following completion of the measurement program, we supported the analysis and interpretation of the experimental data.

Fritts, D. C.↗

Modeling and Simulation for Multi-Missions Space Exploration Vehicle

Asteroids and Near-Earth Objects [NEOs] are of great interest for future space missions. The Multi-Mission Space Exploration Vehicle [MMSEV] is being considered for future Near Earth Object missions and requires detailed planning and study of its Guidance, Navigation, and Control [GNC]. A possible mission of the MMSEV to a NEO would be to navigate the spacecraft to a stationary orbit with respect to the rotating asteroid and proceed to anchor into the surface of the asteroid with robotic arms. The Dynamics and Real-Time Simulation [DARTS] laboratory develops reusable models and simulations for the design and analysis of missions. In this paper, the development of guidance and anchoring models are presented together with their role in achieving mission objectives and relationships to other parts of the simulation. One important aspect of guidance is in developing methods to represent the evolution of kinematic frames related to the tasks to be achieved by the spacecraft and its robot arms. In this paper, we compare various types of mathematical interpolation methods for position and quaternion frames. Subsequent work will be on analyzing the spacecraft guidance system with different movements of the arms. With the analyzed data, the guidance system can be adjusted to minimize the errors in performing precision maneuvers.

Multi-Mission Space Exploration Vehicle [MMSEV]↗

Neural Network Approaches for Mobile Spectroscopic Gamma-Ray Source Detection

Artificial neural networks (ANNs) for performing spectroscopic gamma-ray source identification have been previously introduced, primarily for applications in controlled laboratory settings. To understand the utility of these methods in scenarios and environments more relevant to nuclear safety and security, this work examines the use of ANNs for mobile detection, which involves highly variable gamma-ray background, low signal-to-noise ratio measurements, and low false alarm rates. Simulated data from a 2” × 4” × 16” NaI(Tl) detector are used in this work for demonstrating these concepts, and the minimum detectable activity (MDA) is used as a performance metric in assessing model performance.In addition to examining simultaneous detection and identification, binary spectral anomaly detection using autoencoders is introduced in this work, and benchmarked using detection methods based on Non-negative Matrix Factorization (NMF) and Principal Component Analysis (PCA). On average, the autoencoder provides a 12% and 23% improvement over NMF- and PCA-based detection methods, respectively. Additionally, source identification using ANNs is extended to leverage temporal dynamics by means of recurrent neural networks, and these time-dependent models outperform their time-independent counterparts by 17% for the analysis examined here. The paper concludes with a discussion on tradeoffs between the ANN-based approaches and the benchmark methods examined here.

Bilton, Kyle J. (ORCID:0000000184553689)↗

Quantum dynamics of the temporary capture of light atoms by superfluid helium nanodroplets at very low collision energies (≈1–13 meV): the case of the hydrogen atom and its isotopes

The capture dynamics of a H atom and isotopic variants [D, T and Q (hypothetical isotope of mass equal to four times the mass of H)] by a superfluid helium nanodroplet (HeND) has been investigated theoretically. The HeND (T = 0.37 K) is ( 4 He) N=400 and a mean field quantum hybrid approach [TDDFT (helium) + quantum wave packet (H, D, T or Q)] at zero angular momentum, is used to explore a rather wide range of very low initial kinetic energies (E k,0 ≈ 10–150 K). The analysis of the capture mechanism shows the existence of a dynamical barrier and a dynamical minimum that play key roles to understand the time evolution of the capture, especially the former property. In general, the H atom shows a different behavior from the other isotopes, with the behavior of T and Q being very similar to each other and the D atom behaving inbetween H and T. Besides, it is worth noting that, in principle, at the very low initial kinetic energies considered only “short” and “long” lived atom⋯HeND collision complexes are formed, i.e., in the atom-helium nanodroplet collision only the temporary capture of the atom takes place. The different behaviors observed have been interpreted considering the faster motion of the H atom when colliding with ( 4 He) N=400 and the more quantum character of the H behavior both due to its significantly lower mass. As far as we know, this is the first quantum dynamics study carried out on the collision of light atoms with HeNDs at very low energies.

Sternberg, Michael [Argonne National Laboratory (A↗

The Viability of Trajectory Analysis for Diagnosing Dynamical and Chemical Influences on Ozone Concentrations in the UTLS

The viability of trajectory analysis for diagnosing the interplay between chemistry and dynamics is investigated by comparing ozone mixing ratios modelled using air-parcel pathways to values observed along flight tracks during ATTREX (Airborne Tropical TRopopause EXperiment). Trajectories are initiated at the locations of ozone observations and tracked backward in time to their sources at termini of backward trajectories. The modelled values of ozone utilize 3-dimensional analysis fields from WACCM (Whole Atmosphere Community Climate Model) (a chemical-climate model with dynamical fields nudged towards MERRA (Modern-Era Retrospective Analysis and Research Applications) reanalysis) and ERA-interim (product of ECMWF - the European Centre for Medium-Range Weather Forecasts) to determine source mixing ratios with chemical production and loss terms derived from the ozone chemistry used in WACCM. A statistical base of modelled ozone is constructed with 6 trajectory platforms (adiabatic, diabatic, and kinematic forced by ERA-interim and MERRA), two chemical models (WACCM chemistry and no chemistry), and 4 trajectory lengths (5, 10, 20, and 30 days). Linear regression is employed to separate systematic errors from random errors and to characterize the impact of source mixing ratios, path length, vertical motion, and chemistry on modelled ozone errors. Errors in the analysis ozone fields are large, if not dominant, contributors to model error. Random errors are particularly large for point-by-point comparisons, however averaging over 800 km (75 minutes) flight segments substantially reduces random error and exposes systematic errors. Of the two analysis ozone data sets, WACCM, which incorporates detailed chemistry, provides the smaller systematic errors while ERA-interim, which has crude chemistry but assimilates observational data, has the smaller random errors. Of the different trajectory platforms, adiabatic calculations produce the smaller random errors (irrespective of the use of chemistry) but both vertical motion and chemistry are required to optimally reduce systematic errors. These results suggest that meaningful analysis of dynamical and chemical interactions that control ozone mixing ratios are viable on spatial scales larger than a few reanalysis grid spaces, that errors in the analyzed ozone data sets are large but not prohibitively so, and that vertical velocities and heating rates from reanalysis data, while problematic, contain useful information [on the ozone concentrations in the UTLS (Upper Troposphere/Lower Stratosphere)].

ozone↗

Characterizing skyrmion flow phases with principal component analysis

Principal component analysis (PCA) is a powerful method that can identify patterns in large, complex data sets by constructing low-dimensional order parameters from higher-dimensional feature vectors. There are increasing efforts to use space-and-time-dependent PCA to detect transitions in nonequilibrium systems that are difficult to characterize with equilibrium methods. Here, we demonstrate that feature vectors incorporating the position and velocity information of driven skyrmions moving through random disorder permit PCA to resolve different types of disordered skyrmion motion as a function of driving force and the ratio of the Magnus force to the dissipation. Since the Magnus force creates gyroscopic motion and a finite Hall angle, skyrmions can exhibit a greater range of flow phases than what is observed in overdamped driven systems with quenched disorder. We show that in addition to identifying previously known skyrmion flow phases, PCA detects several additional phases, including different types of channel flow, moving fluids, and partially ordered states. Guided by the PCA analysis, we further characterize the disordered flow phases to elucidate the different microscopic dynamics and show that the changes in the PCA-derived order parameters can be connected to features in bulk transport measures, including the transverse and longitudinal velocity-force curves, differential conductivity, topological defect density, and changes in the skyrmion Hall angle as a function of drive. We discuss how asymmetric feature vectors can be used to improve the resolution of the PCA analysis, and how this technique can be extended to find disordered phases in other nonequilibrium systems with time-dependent dynamics.

36 MATERIALS SCIENCE↗