Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Computational Fluid Dynamics Conduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Interaction of two glancing, crossing shock waves with a turbulent boundary-layer at various Mach numbers

A preliminary experimental investigation was conducted to study two crossing, glancing shock waves of equal strengths, interacting with the boundary-layer developed on a supersonic wind tunnel wall. This study was performed at several Mach numbers between 2.5 and 4.0. The shock waves were created by fins (shock generators), spanning the tunnel test section, that were set at angles varying from 4 to 12 degrees. The data acquired are wall static pressure measurements, and qualitative information in the form of oil flow and schlieren visualizations. The principle aim is two-fold. First, a fundamental understanding of the physics underlying this flow phenomena is desired. Also, a comprehensive data set is needed for computational fluid dynamic code validation. Results indicate that for small shock generator angles, the boundary-layer remains attached throughout the flow field. However, with increasing shock strengths (increasing generator angles), boundary layer separation does occur and becomes progressively more severe as the generator angles are increased further. The location of the separation, which starts well downstream of the shock crossing point, moves upstream as shock strengths are increased. At the highest generator angles, the separation appears to begin coincident with the generator leading edges and engulfs most of the area between the generators. This phenomena occurs very near the 'unstart' limit for the generators. The wall pressures at the lower generator angles are nominally consistent with the flow geometries (i.e. shock patterns) although significantly affected by the boundary-layer upstream influence. As separation occurs, the wall pressures exhibit a gradient that is mainly axial in direction in the vicinity of the separation. At the limiting conditions the wall pressure gradients are primarily in the axial direction throughout.

Hingst, Warren R.↗
NASA NTRS2003

Performance Analysis of a Hybrid Overset Multi-Block Application on Multiple Architectures

This paper presents a detailed performance analysis of a multi-block overset grid compu- tational fluid dynamics app!ication on multiple state-of-the-art computer architectures. The application is implemented using a hybrid MPI+OpenMP programming paradigm that exploits both coarse and fine-grain parallelism; the former via MPI message passing and the latter via OpenMP directives. The hybrid model also extends the applicability of multi-block programs to large clusters of SNIP nodes by overcoming the restriction that the number of processors be less than the number of grid blocks. A key kernel of the application, namely the LU-SGS linear solver, had to be modified to enhance the performance of the hybrid approach on the target machines. Investigations were conducted on cacheless Cray SX6 vector processors, cache-based IBM Power3 and Power4 architectures, and single system image SGI Origin3000 platforms. Overall results for complex vortex dynamics simulations demonstrate that the SX6 achieves the highest performance and outperforms the RISC-based architectures; however, the best scaling performance was achieved on the Power3.

Djomehri, M. Jahed↗
NASA NTRS2011

Two-Dimensional Finite Element Ablative Thermal Response Analysis of an Arcjet Stagnation Test

The finite element ablation and thermal response (FEAtR, hence forth called FEAR) design and analysis program simulates the one, two, or three-dimensional ablation, internal heat conduction, thermal decomposition, and pyrolysis gas flow of thermal protection system materials. As part of a code validation study, two-dimensional axisymmetric results from FEAR are compared to thermal response data obtained from an arc-jet stagnation test in this paper. The results from FEAR are also compared to the two-dimensional axisymmetric computations from the two-dimensional implicit thermal response and ablation program under the same arcjet conditions. The ablating material being used in this arcjet test is phenolic impregnated carbon ablator with an LI-2200 insulator as backup material. The test is performed at the NASA, Ames Research Center Interaction Heating Facility. Spatially distributed computational fluid dynamics solutions for the flow field around the test article are used for the surface boundary conditions.

Dec, John A.↗
NASA NTRS2018

Aerodynamic and Structural Evaluation of an SMA Slat-Cove Filler Using Computational and Experimental Tools at Model Scale

Transport class aircraft produce a significant amount of airframe noise during approach and landing due to exposed geometric discontinuities that are hidden during cruise. The leading-edge slat is a primary contributor to this noise. In previous work, use of a slat-cove filler (SCF) has proven to reduce airframe noise by filling the cove aft of the slat, eliminating the circulation region within the cove. The goal of this work is to extend and improve upon past experimental and computational efforts on the evaluation of a scaled high-lift wing with a super elastic shape memory alloy (SMA) SCF. Recent turbulence measurements of the Texas A&M University 3ft-by-4ft wind tunnel allow for more accurate representation of the flow through the test section in computational fluid dynamics (CFD) analysis. The finite volume models used in CFD analysis are coupled to structural finite element models using a framework compatible with an SMA constitutive model and significant deformation, enabling fluid-structure interaction (FSI) analysis of the SCF. Both fully-deployed and retraction/deployment cases are considered. The displacement of the SCF on the experimental model is measured at various stages of retraction/deployment using a laser displacement sensor and digital image correlation system. Due to a lack of structural stiffness in the 3D-printed plastic slat during retraction and SCF stowage, a rigid steel slat is incorporated into the physical model and preliminary wind tunnel tests are conducted at multiple angles of attack in both retracted and deployed configurations.

Scholten, William↗
NASA NTRS1997

Enhanced Control Effector Designs for Airbreathing Transatmospheric Vehicles

A study was conducted to evaluate the potential effectiveness of a moveable cowl-trailing-edge design for airbreathing hypersonic single-stage-to-orbit (SSTO) configurations, which can be extended or deflected from the nominal position in order to provide additional pitching moment capability. This additional pitching moment capability may reduce the necessary deflection angle from conventional control surfaces and the associated trim drag penalty. Calculations for a generic SSTO configuration with baseline and modified cowl trailing edge geometries were performed at Mach 6 and 10 initially with an engineering analysis code in order to examine several design parametrics. In order to more accurately model geometries and flow physics, 2-D viscous computational fluid dynamics (CFD) predictions were obtained. FInally, a limited set of 3D CFD predictions were obtained at Mach 6 in order to show the effects of modeling 3D flow fields as well as the full 3D vehicle geometry. Comparisons of aftbody surface pressures and force and moment predictions show differences between initial predictions and 2-D CFD solutions due to geometry modeling and calculation method differences. The 3-D CFD predictions confirm the trends observed in the 2-D solutions and provide additional information on 3D effects. These analyses shows that cowl-trailing-edge extensions were effective in providing additional (nose-down) pitching moment increments as well as increased thrust compared to the baseline geometry. These effects reduce the control surface deflection angle required to trim the vehicle and the associated trim drag. Cowl-trailingedge deflections were not as effective, generating more nose-up pitching moment and decreased thrust compared to non-deflected cases.

Cockrell, Charles E.↗
NASA NTRSDate not supplied

Particle Impact Simulation and Ignition Prediction

An experimentally calibrated tool is needed to predict if a system is susceptible to failure by particle impact ignition (PI) based on use conditions, materials, and flow geometry. This tool will accelerate new components, evaluating existing hardware, and help disposition anomalies. Conduct particle impact testing with in-situ diagnostics and complementary simulations on subset of key engineering materials (IN718, M400, 316L, 6061, Ti64, Zr) to develop a proof-of-concept predictive tool for assessing the risk of PI for idealized geometries (spherical particles) in realistic environments. Assess particle/target interactions (coefficient of restitution, ignition, kindling) using instrumented particle impact rigs while systematically varying key parameters (materials, particle size, environment, target configuration). Determine key field variables (temperature, strain, stress) in particle impacts using Multiphysics finite element and hydrocode simulations validated through comparison with experimental measurements and observations. Synthesize experiments and simulations into constitutive models for PI that can be integrated with existing computational fluid dynamics (CFD) and Debris Transport Analysis (DTA) tools in future efforts

particle impact↗
NASA NTRS2024

Particle Impact Simulation and Ignition Prediction

An experimentally calibrated tool is needed to predict if a system is susceptible to failure by particle impact ignition (PI) based on use conditions, materials, and flow geometry. This tool will accelerate new components, evaluating existing hardware, and help disposition anomalies. - Conduct particle impact testing with in-situ diagnostics and complementary simulations on subset of key engineering materials (IN718, M400, 316L, 6061, Ti64, Zr) to develop a proof-of-concept predictive tool for assessing the risk of PI for idealized geometries (spherical particles) in realistic environments. - Assess particle/target interactions (coefficient of restitution, ignition, kindling) using instrumented particle impact rigs while systematically varying key parameters (materials, particle size, environment, target configuration). - Determine key field variables (temperature, strain, stress) in particle impacts using Multiphysics finite element and hydrocode simulations validated through comparison with experimental measurements and observations. - Synthesize experiments and simulations into constitutive models for PI that can be integrated with existing computational fluid dynamics (CFD) and Debris Transport Analysis (DTA) tools in future efforts.

Jonathan Tylka↗
NASA NTRS2023

Turbulence Model Validation Through Joint Experimental /Computational Studies of Separated Flow Over A Three-Dimensional Tapered Bump: Part I - Experimental Investigation

The results of a three-year experimental campaign aimed at comprehensively documenting the separated flow over a three-dimensional bump are presented with the purpose of generating a benchmark experimental database useful in validating computational fluid dynamics (CFD) flow simulations. The bump model geometry was designed to provide well-defined and repeatable smooth-body flow separation conditions that were suitable for both experiments and simulations. The bump had a Gaussian streamwise profile with a constant height equal to 8.5% of its width over the central 60% of the test section width. The remaining 40% were outboard spanwise portions that gradually taper to zero using an error function profile to minimize side-wall boundary layer effects. The model was immersed in a turbulent boundary layer that was developed on a suspended flat plate in the Notre Dame Mach 0.6 Wind Tunnel. In order to document the effect of the incoming boundary layer thickness on the flow separation, the bump model could be located at two streamwise positions. The mean velocity and turbulence intensity of the wind tunnel freestream flow field and approaching turbulent boundary layer were fully documented. The measurements of the flow separation region included surface visualization, wall shear stress using oil-film interferometry, mean and dynamic surface pressure, and planar and stereoscopic particle image velocimetry. The experiments were conducted over a range of Mach numbers from 0.05 to 0.2 corresponding to a range of Reynolds numbers based on the test section spanwise dimension (0.914m) of 1.0 × 10 6 ≤ Re L = U ∞ L/ν ≤ 4.0 × 10 6 . The bulk of the results are presented for the higher Mach number conditions of 0.1 and 0.2 with Re L = 2.0 × 10 6 and 4.0 × 10 6 , respectively. Extensive uncertainty analysis of the data was performed. The data is archived in the NASA Langley Turbulence Modeling Resource website at https://turbmodels.larc.nasa.gov/Other_exp_Data/speedbump_sep_exp.html. In addition to the experiments, a computational effort was made in parallel by the CFD group at Boeing Research & Technology highlighting the usefulness of the data set, which is outlined in the accompanying CFD report.

Flow separation↗
NASA NTRS2011

Contributions of TetrUSS to Project Orion

The NASA Constellation program has relied heavily on Computational Fluid Dynamics simulations for generating aerodynamic databases and design loads. The Orion Project focuses on the Orion Crew Module and the Orion Launch Abort Vehicle. NASA TetrUSS codes (GridTool/VGRID/USM3D) have been applied in a supporting role to the Crew Exploration Vehicle Aerosciences Project for investigating various aerodynamic sensitivities and supplementing the aerodynamic database. This paper provides an overview of the contributions from the TetrUSS team to the Project Orion Crew Module and Launch Abort Vehicle aerodynamics, along with selected examples to highlight the challenges encountered along the way. A brief description of geometries and tasks will be discussed followed by a description of the flow solution process that produced production level computational solutions. Four tasks conducted by the USM3D team will be discussed to show how USM3D provided aerodynamic data for inclusion in the Orion aero-database, contributed data for the build-up of aerodynamic uncertainties for the aero-database, and provided insight into the flow features about the Crew Module and the Launch Abort Vehicle.

Mcmillin, Susan N.↗
NASA NTRS2018

Sensitivity Analysis for Multidisciplinary Systems (SAMS)

This report describes the research conducted under an interagency collaboration agreement between the Aerospace Systems Directorate of the Air Force Research Laboratory (AFRL/RQ) and the Computational AeroSciences Branch of NASA Langley (NASA LaRC). Both organizations have a long-term goal of developing a modular computational system for coupling fluids and structures to enable both analysis and optimization of aerospace vehicles. Ultimately, the system should support multiple solvers within the fluid and structure domains to allow the best combination for the task at hand, as well as to allow for institutional preferences of specific software components. Towards this goal, the current research was focused on enhancing the existing modal aeroelastic analysis in the NASA FUN3D (Fully-UNstructured three-dimensional CFD (Computational Fluid Dynamics) code) software (Biedron et al. 2018), as well as developing new aeroelastic analysis and optimization capabilities based on a non-linear finite-element method. The methods and enhancements described in this document pertain to FUN3D Version 13.4.

Biedron, Robert T.↗
NASA NTRS1991

Three-dimensional flows in a transonic compressor rotor

This study involves an experimental and numerical investigation of the three-dimensional flows in a transonic compressor rotor. A variety of data which could be used, in a complementary fashion, to validate/calibrate the computational fluid dynamics turbomachinery code and improve understanding of the flow physics, were acquired. Detailed radial survey data which consisted of total pressure, total temperature, static pressure and flow angle were obtained at stations upstream and downstream of the rotor blade. Detailed velocity and turbulence profiles were obtained upstream of the rotor and used as the upstream boundary conditions for the numerical analysis. Calibrated flush-mounted hot film probes were used to measure wall shear stress on the hub and casing walls upstream of the rotor. The blade-to-blade shear-stress angle distributions were obtained at two axial locations on the rotor casing, using flush-mounted hot film probes. A numerical analysis conducted using a three-dimensional Navier-Stokes code was compared with the experimental results.

Reid, Lonnie↗
NASA NTRS1990

Introduction to the internal fluid mechanics research session

Internal fluid mechanics research at LeRC is directed toward an improved understanding of the important flow physics affecting aerospace propulsion systems, and applying this improved understanding to formulate accurate predictive codes. To this end, research is conducted involving detailed experimentation and analysis. The following three papers summarize ongoing work and indicate future emphasis in three major research thrusts: inlets, ducts, and nozzles; turbomachinery; and chemical reacting flows. The underlying goal of the research in each of these areas is to bring internal computational fluid mechanic to a state of practical application for aerospace propulsion systems. Achievement of this goal requires that carefully planned and executed experiments be conducted in order to develop and validate useful codes. It is critical that numerical code development work and experimental work be closely coupled. The insights gained are represented by mathematical models that form the basis for code development. The resultant codes are then tested by comparing them with appropriate experiments in order to ensure their validity and determine their applicable range. The ultimate user community must be a part of this process to assure relevancy of the work and to hasten its practical application. Propulsion systems are characterized by highly complex and dynamic internal flows. Many complex, 3-D flow phenomena may be present, including unsteadiness, shocks, and chemical reactions. By focusing on specific portions of a propulsion system, it is often possible to identify the dominant phenomena that must be understood and modeled for obtaining accurate predictive capability. The three major research thrusts serve as a focus leading to greater understanding of the relevant physics and to an improvement in analytic tools. This in turn will hasten continued advancements in propulsion system performance and capability.

Miller, Brent A.↗
NASA NTRS2014

Wind Tunnel Testing of a 120th Scale Large Civil Tilt-Rotor Model in Airplane and Helicopter Modes

In April 2012 and October 2013, NASA and the U.S. Army jointly conducted a wind tunnel test program examining two notional large tilt rotor designs: NASA's Large Civil Tilt Rotor and the Army's High Efficiency Tilt Rotor. The approximately 6%-scale airframe models (unpowered) were tested without rotors in the U.S. Army 7- by 10-foot wind tunnel at NASA Ames Research Center. Measurements of all six forces and moments acting on the airframe were taken using the wind tunnel scale system. In addition to force and moment measurements, flow visualization using tufts, infrared thermography and oil flow were used to identify flow trajectories, boundary layer transition and areas of flow separation. The purpose of this test was to collect data for the validation of computational fluid dynamics tools, for the development of flight dynamics simulation models, and to validate performance predictions made during conceptual design. This paper focuses on the results for the Large Civil Tilt Rotor model in an airplane mode configuration up to 200 knots of wind tunnel speed. Results are presented with the full airframe model with various wing tip and nacelle configurations, and for a wing-only case also with various wing tip and nacelle configurations. Key results show that the addition of a wing extension outboard of the nacelles produces a significant increase in the lift-to-drag ratio, and interestingly decreases the drag compared to the case where the wing extension is not present. The drag decrease is likely due to complex aerodynamic interactions between the nacelle and wing extension that results in a significant drag benefit.

Wind Tunnel Testing of a 1/20th Scale↗
NASA NTRS1985

Research Reports: 1984 NASA/ASEE Summer Faculty Fellowship Program

A NASA/ASEE Summer Faulty Fellowship Program was conducted at the Marshall Space Flight Center (MSFC). The basic objectives of the programs are: (1) to further the professional knowledge of qualified engineering and science faculty members; (2) to stimulate an exchange of ideas between participants and NASA; (3) to enrich and refresh the research and teaching activities of the participants' institutions; and (4) to contribute to the research objectives of the NASA Centers. The Faculty Fellows spent ten weeks at MSFC engaged in a research project compatible with their interests and background and worked in collaboration with a NASA/MSFC colleague. This document is a compilation of Fellows' reports on their research during the summer of 1984. Topics covered include: (1) data base management; (2) computational fluid dynamics; (3) space debris; (4) X-ray gratings; (5) atomic oxygen exposure; (6) protective coatings for SSME; (7) cryogenics; (8) thermal analysis measurements; (9) solar wind modelling; and (10) binary systems.

Freeman, L. M.↗
NASA NTRS1993

Hypersonic engine component experiments in high heat flux, supersonic flow environment

A major concern in advancing the state-of-the-art technologies for hypersonic vehicles is the development of an aeropropulsion system capable of withstanding the sustained high thermal loads expected during hypersonic flight. Even though progress has been made in the computational understanding of fluid dynamics and the physics/chemistry of high speed flight, there is also a need for experimental facilities capable of providing a high heat flux environment for testing component concepts and verifying/calibrating these analyses. A hydrogen/oxygen rocket engine heat source was developed at the NASA Lewis Research Center as one element in a series of facilities at national laboratories designed to fulfill this need. This 'Hot Gas Facility' is capable of providing heat fluxes up to 450 w/sq cm on flat surfaces and up to 5,000 w/sq cm at the leading edge stagnation point of a strut in a supersonic flow stream. Gas temperatures up to 3050 K can also be attained. Two recent experimental programs conducted in this facility are discussed. The objective of the first experiment is to evaluate the erosion and oxidation characteristics of a coating on a cowl leading edge (or strut leading edge) in a supersonic, high heat flux environment. Macrophotographic data from a coated leading edge model show progressive degradation over several thermal cycles at aerothermal conditions representative of high Mach number flight. The objective of the second experiment is to assess the capability of cooling a porous surface exposed to a high temperature, high velocity flow environment and to provide a heat transfer data base for a design procedure. Experimental results from transpiration cooled surfaces in a supersonic flow environment are presented.

Gladden, Herbert J.↗
NASA NTRS2003

Pulsed Ejector Wave Propogation Test Program

The development of, and initial test data from, a nondetonating Pulse Detonation Engine (PDE) simulator tested in the NASA Glenn 1 x 1 foot Supersonic Wind Tunnel (SWT) is presented in this paper. The concept is a pulsed ejector driven by the simulated exhaust of a PDE. This pro- gram is applicable to a PDE entombed in a ramjet flowpath, i.e., a PDE combined-cycle propulsion system. The ejector primary flow is a pulsed, uiiderexpanded, supersonic nozzle simulating the supersonic waves ema- nating from a PDE, while the ejector secondary flow is the 1 x 1 foot SWT test section operated at subsonic Mach numbers. The objective is not to study the detonation details, but the wave physics including t,he start- ing vortices, the extent of propagation of the wave front, the reflection of the wave from the secondary flowpath walls, and the timing of these events of a pulsed ejector, and correlate these with Computational Fluid Dynamics (CFD) code predictions. Pulsed ejectors have been shown to result in a 3 to 1 improvement in LID (length-to-diameter) and a near 2 to 1 improvement in thrust augmentation over a steady ejector. This program will also explore the extent of upstream interactions between an inlet and large, periodically applied, backpressures to the inlet as would be present due to combustion tube detonations in a PDE. These interactions could result in inlet unstart or buzz for a supersonic mixed compression inlet. The design of the present experiment entailed the use of an 2-t diagram characteristics code to study the nozzle filling and purging timescales as well as a series of CFD analyses conducted using the WIND code. The WIND code is a general purpose CFD code for solution of the Reynolds averaged Navier-Stokes equations and can be applied to both steady state and time-accurate calculations. The first, proof-of-concept, test entry (spring 2001) pressure distributions shown here indicate the simulation concept was successful and therefore the experimental approach is sound.

Fernandez, Rene↗
NASA NTRS2002

Aeroheating Predictions for the X-43 Cowl-Closed Configuration at Mach 7 and 10

A pre-flight analysis was conducted for the Mach 7 and Mach 10 X-43 cowl-closed configurations to evaluate three-dimensional flow-field effects on localized heating in the vicinity of the closed cowl flap and sidewall. First, engineering-level analyses based on documented laminar and turbulent surface heating database were used to estimate localized heating amplification factors to account for turbulent flow effects, corner flow effects and the presence of forebody boundary layer trip devices. These estimated factors were applied to 2-D computational predictions to develop surface heat loads. Second, thin-film gauge surface heating data were obtained for a Mach 10 cowl-closed configuration in a reflected shock tunnel at simulated flight conditions. Third, computational fluid dynamics (CFD) flow-field predictions were obtained at Mach 10 ground test conditions to provide comparisons with the engineering database predictions and experimental measurements. Similarly, a CFD solution was also obtained at Mach 7 flight conditions to provide qualitative comparisons with engineering predictions. The Mach 10 CFD predictions compare favorably with the experimental measurements and the engineering estimates for surface heating amplification on the closed cowl. However, experimental measurements were not of sufficient quantity on the sidewall surface to capture the highest localized heating rates, and also the Mach 10 CFD predictions suggest higher peak heating on the sidewall compared to the engineering estimates. Also, the Mach 7 CFD predictions indicate qualitative agreement with the database estimates in terms of flow-field structure and peak heating locations on the closed-cowl flap and sidewall surfaces.

Cockrell, Charles E., Jr.↗
NASA NTRS2004

Benchmark Wall Heat Flux Data for a GO2/GH2 Single Element Injector

Computational Fluid Dynamics (CFD) is becoming an important component of injector design in the rocket industry. Injector designers who use CFD in the design process need to understand the accuracy level of the particular code being used for certain aspects of the design. This paper presents a recent effort to acquire benchmark quality data to be used for CFD code validation. Detailed chamber wall temperature and heat flux data was acquired for a gaseous oxygen, gaseous hydrogen single element shear coaxial injector in a 1.5 inch diameter copper heat sink chamber at Penn State University. The data was taken using both coaxial and water cooled heat flux gauges. Tests were run using hot gases generated from both fuel and oxidizer preburners. Tests were conducted over a chamber pressure range of 300 to 750 psia. Data analysis and uncertainty information will also be presented.

Pal, Sibtosh↗