Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Coarse graining”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Automated array assembly task development of low-cost polysilicon solar cells

Development of low cost, large area polysilicon solar cells was conducted in this program. Three types of polysilicon materialk were investigated. A theoretical and experimenal comparison between single crystal silicon and polysilicon solar cell efficiency was performed. Significant electrical performance differences were observed between types of wafer material, i.e. fine grain and coarse grain polysilicon and single crystal silicon. Efficiency degradation due to grain boundaries in fin grain and coarse grain polysilicon was shown to be small. It was demonstrated that 10 percent efficient polysilicon solar cells can be produced with spray on n+ dopants. This result fulfills an important goal of this project, which is the production of batch quantity of 10 percent efficient polysilicon solar cells.

Jones, G. T.↗

Precipitation Kinetics of M{sub 23}C{sub 6} Carbides in the Super304H Austenitic Heat-Resistant Steel

The precipitation kinetics of M{sub 23}C{sub 6} carbides in Super304H and TP304H steels were investigated using the selective-etching method, SEM backscattered electron images and Image-Pro-Plus 6.0 software. Precipitation–temperature–time (PTT) diagrams of M{sub 23}C{sub 6} carbides in the as-received Super304H (fine grains), coarsened Super304H (coarse grains) and TP304H (coarse grains) steels all show the typical C-shaped character with nose temperature range from 800 to 850 °C. Compared with the TP304H steel, the same trend is found of the PTT curve of M{sub 23}C{sub 6} carbides for both kinds of Super304H steels, but their start lines move to the right and finish lines to the left. The preferential formation of Nb(C,N) phase at grain boundaries in the Super304H steels inhibited the nucleation of M{sub 23}C{sub 6} carbides in the early stage of precipitation, causing the right shift of the start line of PTT curve. The main reason for the left shift of the finish line of the two Super304H steels was the quicker growing and coarsening rate of M{sub 23}C{sub 6} in the later precipitation stage due to their higher C content than in TP304H. For the difference in PPT curves between the two grain sizes of the Super304H steel, the lower diffusion rate of atoms in the coarse-grained Super304H steel may explain its righter finish line than the fine-grained counterpart, while the reason for its lefter start line is due to the higher solute segregation along coarse-grained boundaries.

36 MATERIALS SCIENCE↗

Initial Isotopic Heterogeneities in ZAGAMI: Evidence of a Complex Magmatic History

Interpretations of Zagami s magmatic history range from complex [1,2] to relatively simple [3]. Discordant radiometric ages led to a suggestion that the ages had been reset [4]. In an attempt to identify the mechanism, Rb-Sr isochrons were individually determined for both fine-grained and coarse-grained Zagami [5]. Ages of approx.180 Ma were obtained from both lithologies, but the initial Sr-87/Sr-86 (ISr) of the fine-grained lithology was higher by 8.6+/-0.4 e-units. Recently, a much older age of approx.4 Ga has been advocated [6]. Here, we extend our earlier investigation [5]. Rb-Sr Data: In [5] we applied identical, simplified, procedures to both lithologies to test whether a grain-size dependent process such as thermally-driven subsolidus isotopic reequilibration had caused age-resetting. Minerals were separated only by density. In the present experiment, purer mineral separates were analysed with improved techniques. Combined Rb-Sr results give ages (T) = 166+/-12 Ma and 177+/-9 Ma and I(subSr) = 0.72174+/-9 and 0.72227+/-7 for the coarse-grained and fine-grained lithologies, respectively. ISr in the fine-grained sample is thus higher than in the coarse-grained sample by 7.3+/-1.6 e-units. The results for the coarse-grained lithology are in close agreement with T = 166+/-6 Ma, ISr = 0.72157+/-8 for an adjacent sample [7] and T = 178+/-4 Ma, ISr = 0.72151+/-5 [4, adjusted] for a separate sample. Thus, fine-grained Zagami appears on average to be less typical of the bulk than coarse-grained Zagami.

Nyquist, L. E.↗

The Effect of Solution Heat Treatment on an Advanced Nickel-Base Disk Alloy

Five heat treat options for an advanced nickel-base disk alloy, LSHR, have been investigated. These included two conventional solution heat treat cycles, subsolvus/oil quench and supersolvus/fan cool, which yield fine grain and coarse grain microstructure disks respectively, as well as three advanced dual microstructure heat treat (DMHT) options. The DMHT options produce disks with a fine grain bore and a coarse grain rim. Based on an overall evaluation of the mechanical property data, it was evident that the three DMHT options achieved a desirable balance of properties in comparison to the conventional solution heat treatments for the LSHR alloy. However, one of the DMHT options, SUB/DMHT, produced the best set of properties, largely based on dwell crack growth data. Further evaluation of the SUB/DMHT option in spin pit experiments on a generic disk shape demonstrated the advantages and reliability of a dual grain structure at the component level.

Gayda, J.↗

Machining induced fissures in relation to microstructure of sintered U3Si2 fuel pellets

As uranium silicide (U3Si2) becomes a more desired fuel replacement for uranium dioxide in light water reactors, it is import to understand the fabrication process. Moreover, it is important to understand how the as-sintered microstructure of the fuel pellet affects the final product; uranium silicide fuel pellets are currently fabricated using a powder metallurgy process. Pellet quality and integrity is a concern as any unwanted defects may cause adverse irradiation behavior. Thus, pellets need to remain relatively free of defects (surface chipping, cracking, undesired microstructure, etc.) in order to be placed into a fuel assembly. Recently, it was observed that uranium silicide fuel pellets developed surface fissures on the machined surface after a centerless grinding process. Initial observations indicate a relation between microstructure and machining induced fissures; in essence, fissures on the machined surface are only observed in pellets containing a non-uniform texture (fine grains surrounding coarse grains). Experiments have been focused on determining the cause(s) of the non-uniform texture. Once the cause was determined and grain size was reproduced, samples with a coarse-grained microstructure, along with samples containing a fine-grained microstructure were centerless ground to confirm the relation between surface fissures and microstructure. Samples were also subjected to microscopic analysis, grain size analysis, and x-ray diffraction (XRD).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Forging of Advanced Disk Alloy LSHR

The powder metallurgy disk alloy LSHR was designed with a relatively low gamma precipitate solvus temperature and high refractory element content to allow versatile heat treatment processing combined with high tensile, creep and fatigue properties. Grain size can be chiefly controlled through proper selection of solution heat treatment temperatures relative to the gamma precipitate solvus temperature. However, forging process conditions can also significantly influence solution heat treatment-grain size response. Therefore, it is necessary to understand the relationships between forging process conditions and the eventual grain size of solution heat treated material. A series of forging experiments were performed with subsequent subsolvus and supersolvus heat treatments, in search of suitable forging conditions for producing uniform fine grain and coarse grain microstructures. Subsolvus, supersolvus, and combined subsolvus plus supersolvus heat treatments were then applied. Forging and subsequent heat treatment conditions were identified allowing uniform fine and coarse grain microstructures.

Gabb, Timothy P.↗

Investigation of Best-Practices and Computationally Inexpensive Radiative Exchange Models for Discrete Element Method Modeling of Aluminosilicate Particles in Concentrating Solar Power Environments

Chemically inert, aluminosilicate based particles have been investigated as both a thermal transport and sensible energy storage medium for concentrating solar power facilities. These particles will experience a wide range of operating temperatures (300-1000 K) and handling conditions (dense to dilute falling particle curtains, dense granular flows, or dense structures), requiring specially-designed and optimized infrastructures. The relative influence of collisional and frictional interactions between particles varies based on temperature-dependent particulate properties and greatly impacts the bulk, granular flow behavior. These underlying physics are captured using discrete element method modeling tools. However, this modeling method is computationally expensive as each particle position and interaction is tracked during the simulation. These modeling methods are further complicated by introducing temperature-dependent particle properties, high-temperature radiative exchange, and directional irradiation sources experienced by granular flows in concentrating solar power environments. In this study, coupled experimental and numerical slump testing of aluminosilicate particles was performed and computationally efficient radiative exchange models were evaluated to establish best-practices for discrete element method models for concentrating solar power environments. The three particle types investigated included Carbobead HSP 30 /60, Carbobead CP 30/60, and Granusil 4030. Existing modeling limitations and computationally-efficient multi-modal heat transfer models were evaluated using Aspherix®, a commercial discrete element method software. High-temperature (< 1073 K) slump testing of aluminosilicate particles was performed to investigate the deviation between experimentally-observed and numerically-predicted angles of repose introduced by computation-time reduction practices including the relaxation of the particle elastic modulus and coarse-graining. Coarse-graining is used to use a single modeled particle that is representative of a collection of smaller particles, decreasing the computational cost at the expense of geometric accuracy. Additionally, relaxation of the elastic modulus is used to reduce computational time at the expense of an increased, modeled particle overlap. Prior studies have determined that aluminosilicate particles retain a high elastic modulus at high temperatures (< 1073 K), requiring small simulation timesteps to ensure resolved contact forces resemble appropriate solid mechanics. A parametric study was performed to evaluate the influence of computation time improvements on the deviation between experimental and modeled angle of repose across high temperatures < 1073 K. Additionally, numerical case studies were performed on candidate particle systems at varying porosities and temperatures. These studies were performed to investigate the influence of computationally-efficient radiative-exchange modeling methods coupled to Aspherix® on modeled accuracy and computation time. The recently-developed distance-based approximation was evaluated in estimating radiative exchange between particles and participating surfaces located in close proximity. The distance based approximation was developed to use tabulated estimates of the radiative distribution factor between individual particles and surfaces in close proximity (< 40 particle radii). These methods were expanded to the aluminosilicate particles of interest, including the influence of particle size distributions. To capture radiative exchange between particles and surfaces not in close proximity (> 40 particle radii) and to capture the absorption of directional irradiation from concentrating solar resources, a volumetrically-averaged radiative distribution factor was calculated between the modeled granular flow and surfaces using Monte Carlo ray-tracing for participating media. Volume-averaged absorption and scattering coefficients were predicted using a volumetric discretization of the modeled domain with monodisperse approximations based on geometric optics and experimentally-determined scattering phase functions for aluminosilicate particles.

14 SOLAR ENERGY↗

Terrestrial Analogs for Clay Minerals at Yellowknife Bay, Gale Crater, Mars

Sediments of the Sheepbed unit, Gale Crater, were analyzed by the CheMin X-ray diffraction instrument on the Curiosity Rover. The sediments consist of typical basalt minerals (Fe-forsterite, augite, pigeonite, plagioclase), as well as Fe oxide/hydroxides, Fesulfides, amorphous material, and a phyllosilicate. The phyllosilicate has a broad 001 peak at approx 1.0 nm, consistent with a poorly ordered smectite. However, in the absence of diagnostic tests possible on Earth, its identity is not clear. The position of the 06L diffraction band is generally used to distinguish dioctahedral from trioctahedral smectite, but it is beyond CheMin's range of 2 Theta. The measured position of the 02L diffraction band (approx 22.5deg 2 Theta by CheMin), implies that the smectite is trioctahedral. The exact position and shape of the 02L band is determined by the cations in the 'M' sites of the smectite; to constrain those cations, we sought analogs among terrestrial smectites, emphasizing those developed from basaltic precursors. A potential analog for the Sheepbed smectite is 'griffithite,' a variety of trioctahedral smectite in altered basalt of the Topanga formation, Griffith Park, Los Angeles. 'Griffithite' has an 02L diffraction band that is close in position and shape to that of the Sheepbed smectite, although 'griffithite' has a very sharp 001 peak, indicating a high degree of layer ordering not seen in the Sheepbed smectite. A typical chemical formula for 'griffithite,' determined by electron microprobe, is (Ca0.59 Na0.03) (Mg4.28 Fe1.83) (Si6.64 Al1.36) O20 (OH)4, normalized to Si+Al=8. This formula is consistent with a fully trioctahedral Fe-Mg smectite with Ca and Na as interlayer cations. In the Topanga basalt, four types of 'griffithite' are present: fine-grained, filling cracks and vesicles; coarse-grained, filling vesicles; coarse-grained, replacing olivine phenocrysts; and coarse-grained, replacing glassy mesostasis. The fine-grained 'griffithite' formed first, and the last three varieties may be contemporaneous. One sample shows agate (alpha- quartz) that was precipitated between the episodes of deposition of the fine-grained and coarse-grained 'griffithite.' 'Griffithite' is not unique as a possible terrestrial analog - some clay minerals from the Doushantou formation, China, have similar 02L diffraction bands, and many basalts contain smectites in vesicles and as replacements after olivine. Similar trioctahedral smectites occur also in the nakhlite martian meteorites - as veinlets and replacements of olivine. By understanding the formation of these terrestrial clays, we hope to constrain the nature and mechanism of formation of the Sheepbed clay mineral.

Treiman, Allan H↗

Force field parameter estimation of functional perfluoropolyether lubricants

The head disk interface in a hard disk drive can be considered to be one of the hierarchical multiscale systems, which require the hybridization of multiscale modeling methods with coarse-graining procedure. However, the fundamental force field parameters are required to enable the coarse-graining procedure from atomistic/molecular scale to mesoscale models. In this paper, we investigate beyond molecular level and perform ab initio calculations to obtain the force field parameters. Intramolecular force field parameters for Zdol and Ztetraol were evaluated with truncated PFPE molecules to allow for feasible quantum calculations while still maintaining the characteristic chemical structure of the end groups. Using the harmonic approximation to the bond and angle potentials, the parameters were derived from the Hessian matrix, and the dihedral force constants are fit to the torsional energy profiles generated by a series of constrained molecular geometry optimization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗