Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CIGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

The hunt for the third acceptor in CuInSe 2 and Cu(In,Ga)Se 2 absorber layers

We show the model for intrinsic defects in Cu(In,Ga)Se 2 semiconductor layers is still under debate for the full range between CuInSe 2 and CuGaSe 2 . It is commonly agreed by theory and experiment, that there are at least one shallow donor and two shallow acceptors. Spatially resolved photoluminescence on CuGaSe 2 previously revealed a third acceptor. In this study we show with the same method that the photoluminescence peak at 0.94 eV in CuInSe 2 , previously attributed to a third acceptor, is a phonon replica. However another pronounced peak at 0.9 eV is detected on polycrystalline CuInSe 2 samples grown with high copper and selenium excess. Intensity and temperature dependent photoluminescence measurements reveal that this peak originates from a DA-transition from a shallow donor (<8 meV) into a shallow acceptor A3 (135 [Formula: see text] 10) meV. The DA3 transition has three distinct phonon replicas with 28 meV spectral spacing and a Huang Rhys factor of 0.75. Complementary admittance measurements are dominated by one main step with an activation energy of 125 meV which corresponds well with the found A3 defect. The same defect is also observed in Cu(In,Ga)Se 2 samples with low gallium content. For [Ga]/([Ga] + [In])-ratios of up to 0.15 both methods show a concordant increase of the activation energy with increasing gallium content shifting the defect deeper into the bandgap. The indium vacancy ν In is discussed as a possible origin of the third acceptor level in CuInSe 2 and ν III in Cu(In,Ga)Se 2 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

X-ray fluorescence at nanoscale resolution for multicomponent layered structures: A solar cell case study

The study of a multilayered and multicomponent system by spatially resolved X-ray fluorescence microscopy poses unique challenges in achieving accurate quantification of elemental distributions. This is particularly true for the quantification of materials with high X-ray attenuation coefficients, depth-dependent composition variations and thickness variations. A widely applicable procedure for use after spectrum fitting and quantification is described. This procedure corrects the elemental distribution from the measured fluorescence signal, taking into account attenuation of the incident beam and generated fluorescence from multiple layers, and accounts for sample thickness variations. Deriving from Beer–Lambert's law, formulae are presented in a general integral form and numerically applicable framework. Here, the procedure is applied using experimental data from a solar cell with a Cu(In,Ga)Se 2 absorber layer, measured at two separate synchrotron beamlines with varied measurement geometries. This example shows the importance of these corrections in real material systems, which can change the interpretation of the measured distributions dramatically.

14 SOLAR ENERGY↗

Damage in Monolithic Thin-Film Photovoltaic Modules Due to Partial Shade

The typical configuration of monolithic thin-film photovoltaic modules makes it possible for partial shade to place one or more cells in such a module in reverse bias. Reverse bias operation leads to high voltage, current density, and power density conditions, which can act as driving forces for failure. We showed that a brief outdoor shadow event can cause a 7% permanent loss in power. We applied an indoor partial shade durability test that moves beyond the standard hot spot endurance test by using more realistic mask and bias conditions and by carefully quantifying the permanent change in performance due to the stress. With the addition of a pass criterion based on change in maximum power, this procedure will soon be proposed as a part of the module-type qualification test. All six commercial copper indium gallium diselenide and cadmium telluride modules we tested experienced permanent damage due to the indoor partial shade test, ranging from 4% to 14% loss in maximum power. We conclude by summarizing ways to mitigate partial shade stress at the cell, module, and system levels.

14 SOLAR ENERGY↗

Precursor Reaction Method With High Ga Cu(In,Ga)(S,Se)$_{2}$ to Achieve Increased Open-Circuit Voltage

The precursor reaction process for the fabrication of Cu(In,Ga)Se 2 solar cells potentially allows for low-cost fabrication and scalable processing for manufacturing. Additionally, this process has yielded record efficiencies in lab-scale experiments. Thus far, research on the precursor reaction method has been restricted to relatively low Ga compositions with Ga/(In+Ga) ≈ 25%. By increasing the ratio of Ga, it is possible to increase the bandgap, and thus, increase the open-circuit voltage. This work develops and characterizes the precursor reaction process for use with Ga/(In+Ga) ≈ 50%, with the goal of improving the open-circuit voltage and efficiency. It is shown that with an increased Ga ratio, increased V ∞ is achieved, but the rate of conversion from the precursor to absorber phases is decreased. Additionally, increased Ga improves the film adhesion at increased selenization temperatures as well as improving the film morphology.

14 SOLAR ENERGY↗

Brief: Daily Performance Changes in Metal Halide Perovskite PV Modules

Metal halide perovskite photovoltaic modules deployed outdoors and held at their maximum power point show daily, reversible, relative changes of up to 30% in efficiency between morning and afternoon. Predicting energy yield and quantifying reliability will require properly handling such daily performance changes.

14 SOLAR ENERGY↗

Damp-Heat Induced Degradation of Transparent Conducting Oxides for Thin-Film Solar Cells: Preprint

The stability of intrinsic and Al-doped single- and bi-layer ZnO for thin-film CuInGaSe2 solar cells, along with Al-doped Zn1-xMgxO alloy and Sn-doped In2O3 (ITO) and F-doped SnO2, was evaluated by direct exposure to damp heat (DH) at 85oC and 85% relative humidity. The results show that the DH-induced degradation rates followed the order of Al-doped ZnO and Zn1-xMgxO >> ITO > F:SnO2. The degradation rates of Al:ZnO were slower for films of higher thickness, higher substrate temperature in sputter-deposition, and with dry-out intervals. As inferred from the optical micro-imaging showing the initiation and propagation of degrading patterns and regions, the degradation behavior appears similar for all TCOs, despite the obvious difference in the degradation rate. A degradation mechanism is proposed to explain the temporal process involving thermal hydrolysis.

14 SOLAR ENERGY↗

Thermal and Electrical Effects of Partial Shade in Monolithic Thin-Film Photovoltaic Modules

Photovoltaic cells can be damaged by reverse bias stress, which arises during service when a monolithically integrated thin-film module is partially shaded. We introduce a model for describing a module's internal thermal and electrical state, which cannot normally be measured. Using this model and experimental measurements, we present several results with relevance for reliability testing and module engineering: Modules with a small breakdown voltage experience less stress than those with a large breakdown voltage, with some exceptions for modules having light-enhanced reverse breakdown. Masks leaving a small part of the masked cells illuminated can lead to very high temperature and current density compared to masks covering entire cells.

14 SOLAR ENERGY↗

Interfacial Modifiers for Enhanced Stability and Reduced Degradation of Cu(In,Ga)Se2 Devices

Transparent conductive oxide (TCO) degradation is a known failure mode in thin-film photovoltaic (PV) devices through mechanisms such as resistivity increase and delamination. Here we apply thin interfacial modifiers to aluminum-doped zinc oxide (AZO) to mitigate damp heat induced degradation of electrical performance. Additionally, we demonstrate that these modifiers can be applied to the AZO front contact of a Cu(In, Ga)Se2 device without significantly degrading the device performance, a promising step towards improving the lifetime performance.

14 SOLAR ENERGY↗

Photovoltaic Properties of Selenized CuGa/In Films with Varied Compositions

Thin CuGa/In films with varied compositions were deposited by co-evaporation and then selenized in situ with evaporated selenium. The selenized Cu(In, Ga)Se2 absorbers were used to fabricate 390 solar cells. Cu/(Ga+In) and Ga/(Ga+In) (Cu/III and Ga/III) were independently varied, and photovoltaic performance was optimal at Cu/III of 77-92% for all Ga/III compositions studied (Ga/III ~ 30, 50, and 70%). The best absorbers at each Ga/III composition were characterized with time-resolved photoluminescence, scanning electron microscopy, and secondary ion mass spectrometry, and devices were studied with temperature-dependent current density-voltage, light and electrical biased quantum efficiency, and capacitance-voltage. The best cells with Ga/III ~ 30, 50, and 70% had efficiencies of 14.5, 14.4, and 12.2% and maximum power temperature coefficients of -0.496, -0.452, and -0.413%/degrees C, respectively. This resulted in the Ga/III ~ 50% champion having the highest efficiency at temperatures greater than 40 degrees C, making it the optimal composition for practical purposes. This optimum is understood as a result of the absorber's band gap grading- where minimum band gap dominates short-circuit current density, maximum space charge region band gap dominates open-circuit voltage, and average absorber band gap dominates maximum power temperature coefficient.

14 SOLAR ENERGY↗

Seasonal Trends of Soiling on Photovoltaic Systems

This work investigates the seasonal variability of photovoltaic soiling losses over a 12-month period for 15 soiling stations deployed in the USA. We present a new parameter able to rank the sites according to the cumulative losses occurring over 3- and 6- month periods. The relations between soiling losses and particulate matter are briefly discussed, as well. Moving from long-term to shorter-term data increases the complexity of the analysis: monthly correlations are found to have lower accuracy than the longer-term ones presented in the literature.

14 SOLAR ENERGY↗

The Effects of Absorber Thickness on Reverse-Bias Damage in Cu(In,Ga)Se2 Solar Cells

We studied a variety of absorber thicknesses in Cu(In,Ga)Se 2 devices to examine the ability of the cell to withstand reverse current flow without damage. Absorbers were varied from 2.5 um to 0.4 um, with the expectation that larger reverse current would be allowed to flow at lower voltages as absorbers were made thinner. Our initial experiments showed promise. However, as the efficiency of thin devices was improved, the reverse current allowed at a given voltage decreased. Here we present our negative results on the ability of thin devices to allow higher reverse currents at lower voltages. We also give details on our procedures for reverse-bias testing small-area solar cells. We hope this information will be useful for those who want to study reverse-bias at the cell level.

14 SOLAR ENERGY↗

Evidence of Reversible Oxidation at CuInSe2 Grain Boundaries

Effects related to alkali metal doping and grain boundaries have puzzled the chalcopyrite photovoltaics community for a long time. This study is the first to report reversible oxidation of grain boundaries in CuInSe2 thin films. The phenomenon is observed in sodium-doped films, but not in undoped ones. Cathodoluminescence imaging, secondary ion mass spectrometry and Kelvin probe force microscopy analyses are performed on CuInSe2 thin films before and after exposure to vacuum. The findings suggest the existence of yet unidentified solid-gas equilibria. Resolving the nature of such reactions will provide new insights into the mechanism of alkali metal doping and passivation in chalcopyrite solar cells.

14 SOLAR ENERGY↗

Studying the Recrystallization of Cu(InGa)Se 2 Semiconductor Thin Films by Silver Bromide In-situ Treatment

Cu(In,Ga)Se 2 samples were fabricated using a 3-stage thermal co-evaporation process on molybdenum back contact at low temperature. The process of recrystallization was carried out in between the 2 nd and 3 rd stages by flashing 25 mg of AgBr for 2 minutes. A change in morphological structure was observed as small grains transformed into large grains, as confirmed by XRD and SEM measurements. The decrease of the Ga gradient, seen in the SIMS depth profile, suggests Ga interdiffusion due to AgBr treatment. Altogether, the AgBr treatment contributes to a general improvement in device performance as compared to the as-deposited devices.

14 SOLAR ENERGY↗