Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additive Manufacture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Strength and thermal shock resistance of porous reaction-bonded silicon nitride by direct nitriding of binder jet additively manufactured silicon

The direct nitridation of binder jet additively manufactured silicon to produce porous silicon nitride was explored. The Taguchi Design of Experiments method was used to systematically study the effect of time, temperature, and nitrogen flow rate on the direct nitriding of binder jet additively manufactured silicon to produce porous reaction-bonded silicon nitride (RBSN). Highly porous (61%) samples with high conversion (99%) to silicon nitride were achieved using a thermal profile that utilized two isothermal holds. Further, it was shown that these samples exhibited thermal shock resistance and a low coefficient of thermal expansion. These results indicate that RBSN is readily achievable through additive manufacturing.

Ceramics↗

Electricity use in big area additive manufacturing of fiber-reinforced polymer composites

In recent years, additive manufacturing (AM), especially large-format additive manufacturing (LFAM), has gained momentum in the manufacturing industry. While LFAM offers benefits over conventional manufacturing processes, such as minimizing material waste and providing vast geometric freedom, assessing its sustainability remains challenging due to limited data, particularly on energy consumption. Most existing data pertain to small-scale or desktop AM and are not directly applicable to LFAM. In this study, we conducted real-time measurements of electricity usage for a type of LFAM known as big area additive manufacturing (BAAM), which typically uses fiber-reinforced polymer pellets as feedstock. We collected electricity usage data from fifteen printing jobs over two months in an industrial production setting. These data fill the existing gap and can be reused to enhance the community’s understanding of LFAM electricity usage, support further research, and promote sustainable development in advanced manufacturing technologies.

ecology↗

Introduction to Additive Manufacturing for Propulsion Systems

Additive Manufacturing (AM) has become a prominent technology of interest for manufacturing propulsion components and gaining attention across the aerospace industry. AM is maturing at a rapid pace and providing new design opportunities, novel materials, new industries and supply chains resulting in programmatic and technical performance improvements. The successful use of AM requires a methodical and intentional approach to understanding the concept to utilization lifecycle for AM. This course will provide an overview of the various steps in AM process trades, design, build process, post-processing, certification and infusion of AM. This will provide various lessons learned and experiences that were captured in a recent AIAA textbook titled "Metal Additive Manufactuging for Propulsion Applications" by the session chairs and industry colleagues. This course will include specific liquid rocket engine component examples and that went through the AM lifecycle including hot-fire testing.

Paul R. Gradl↗

Latent image volumetric additive manufacturing

We report volumetric additive manufacturing (VAM) enables rapid printing into a wide range of materials, offering significant advantages over other printing technologies, with a lack of inherent layering of particular note. However, VAM suffers from striations, similar in appearance to layers, and similarly limiting applications due to mechanical and refractive index inhomogeneity, surface roughness, etc. We hypothesize that these striations are caused by a self-written waveguide effect, driven by the gelation material nonlinearity upon which VAM relies, and that they are not a direct recording of non-uniform patterning beams. We demonstrate a simple and effective method of mitigating striations via a uniform optical exposure added to the end of any VAM printing process. We show this step to additionally shorten the period from initial gelation to print completion, mitigating the problem of partially gelled parts sinking before print completion, and expanding the range of resins printable in any VAM printer.

36 MATERIALS SCIENCE↗

Anomaly Detection In Additively Manufactured Parts Using Laser Doppler Vibrometery

Additively manufactured parts are susceptible to non-uniform structure caused by the unique manufacturing process. This can lead to structural weakness or catastrophic failure. Using laser Doppler vibrometry and frequency response analysis, non-contact detection of anomalies in additively manufactured parts may be possible. Preliminary tests show promise for small scale detection, but more future work is necessary.

42 ENGINEERING↗

Geometry-Dependent Solidification Regimes in Metal Additive Manufacturing

Recent modeling and experimental work in additive manufacturing has suggested that cross-sectional geometry may play a significant role in the local development of the solidification structure through its influence on the heat source path. This effect has been rationalized as the transition from a quasi-static point heat source regime, to a regime dominated by the quasi-static motion of an equivalent line source. This work provides a simple analytical framework for determining the conditions under which a system transitions between these regimes. Here, a transient semi-analytical heat transfer model is used to examine a wide range of process conditions and material properties. A simple analytical expression is derived and shown to accurately predict the transition between solidification regimes over these conditions. The functional form of this expression is then used to help understand the importance of various material properties, process parameters, and geometric factors on the characteristics of the solidification conditions. This approach may be used as a simple guideline for optimizing process conditions in response to variations in cross-sectional geometry to produce more consistent microstructural distributions in additively manufactured components.

36 MATERIALS SCIENCE↗

An Investigation of Process Parameter Modifications on Additively Manufactured Inconel 718 Parts

Additive manufacturing (AM) allows for the fabrication of complex parts via layer-by-layer melting of metal powder. Laser powder-bed AM processes use a variety of process parameters including beam power, beam velocity, and hatch spacing to control melting. Alterations to these parameters have often been attempted to reduce porosity, for example, but less work has been done to on comprehensive effects of process parameter modifications. This study looks at the effects of altering these parameters on microstructure, porosity, and mechanical performance of Inconel 718. The results showed that process parameter modifications that result in porosity formation can significantly reduce fatigue life, while microstructure changes were minimal and had little effect on tensile properties. The precipitate structure was not found to be changed significantly. These results can inform future process parameter modifications, as well as heat treatments to optimize mechanical properties.

36 MATERIALS SCIENCE↗

Role of heat treatment and build orientation in the microstructure sensitive deformation characteristics of IN718 produced via SLM additive manufacturing

The benefits of additive manufacturing have been well documented, but prior to these materials being used in critical applications, the deformation mechanisms must be properly characterized. In this work, the role of heat treatment and build orientation of selective laser melting IN718 is investigated through detailed characterization. The microstructure of this material is probed through a combination of electron microscopy to identify the precipitate structure, electron backscatter diffraction to quantify the grain-level features, and synchrotron-based X-ray microcomputed tomography to detect porosity. A high degree of porosity is observed spatially near the free surface of the part, where the contour during the build process meets the interior hatch. Further, microstructure based deformation mechanisms are explored through digital image correlation relative to the grain features after monotonic and cyclic loading and in situ high-energy X-ray diffraction to identify the lattice strain evolution in these materials. Demarcations between the behaviors of the as-built versus post-processed materials are discussed; specifically, in terms of anisotropy with respect to build direction and values of the strength properties, based on the grain morphology, coherent twin formation, and precipitate structure. In conclusion, the presence of dislocation sub-structures within the grains is observed to homogenize deformation within the as-built sample, while strain partitioning is observed during loading of the post-processed sample.

36 MATERIALS SCIENCE↗

Microstructural modification of additively manufactured metals by electropulsing

Additive manufacturing (AM) promises rapid development cycles and fabrication of ready-to-use, geometrically-complex parts. The metallic parts produced by AM often contain highly non-equilibrium microstructures, e.g. chemical microsegregation and residual dislocation networks. While such microstructures can enhance some material properties, they are often undesirable. Many AM parts are thus heat-treated after fabrication, a process that significantly slows production. This study investigated if electropulsing, the process of sending high-current-density electrical pulses through a metallic part, could be used to modify the microstructures of AM 316 L stainless steel (SS) and AlSi10Mg parts fabricated by selective laser melting (SLM) more rapidly than thermal annealing. Electropulsing has shown promise as a rapid postprocessing method for materials fabricated using conventional methods, e.g. casting and rolling, but has never been applied to AM materials. For both the materials used in this study, as-fabricated SLM parts contained significant chemical heterogeneity, either chemical microsegregation (316 L SS) or a cellular interdendritic phase (AlSi10Mg). In both cases, annealing times on the order of hours at high homologous temperatures are necessary for homogenization. Using electropulsing, chemical microsegregation was eliminated in 316 L SS samples after 10, 16 ms electrical pulses. In AlSi10Mg parts, electropulsing produced spheroidized Si-rich particles after as few as 15, 16 ms electrical pulses with a corresponding increase in ductility. Finally, this study demonstrated that electropulsing can be used to modify the microstructures of AM metals.

36 MATERIALS SCIENCE↗

Micromechanical and fatigue in situ synchrotron characterization of an additively manufactured superalloy with porosity

Additive manufacturing (AM) has the potential to transform component production, but its widespread adoption is constrained by defects, such as pores, that compromise structural integrity. Here, this study investigates the influence of porosity on the micromechanical and fatigue response of AM Inconel 718 (IN718), a widely used aerospace superalloy. One baseline specimen with minimal stochastic porosity and another intentionally seeded with lack of fusion (LOF) pores were examined using high-energy X-ray diffraction microscopy (HEDM) and micro-computed tomography during cyclic loading. Fatigue cracks in the LOF specimen initiated more frequently and at lower cycle counts than in the baseline specimen. The number fraction of fatigue cracks that grew was comparatively higher in the LOF specimen. Grain-level metrics, including stress and diffraction spot widths, were quantified using far-field HEDM. Across the thousands of grains detected in both specimens, the pores in the LOF specimen increased the variability of stress and spot width evolution in the azimuthal direction, the latter serving as a surrogate measure of plastic deformation. However, no correlations emerged between these metrics and grain proximity to fatigue crack initiation sites or pores, underscoring the limitations of grain-averaged metrics for predicting fatigue. Nonetheless, the rich dataset reported here provides a foundation for future modeling efforts.

High-energy X-ray diffraction microscopy↗

Differential effect of magnetic alignment on additive manufacturing of magnetocaloric particles

Additive manufacturing of materials using magnetic particles as feedstock has attracted tremendous attention during the past decade owing to its ability to tune both shape and magnetocrystalline anisotropy, which can significantly enhance the magnetic characteristics of materials. We demonstrate that the magnetic response of multilayered thin films of Gd5Si4 can be tailored by controlling the external magnetic field during inkjet printing. The external magnetic field aligns the magnetic particles along their magnetic easy axis, enhancing the magnetic anisotropy of the printed films. Our work demonstrates the ability to print thin magnetic films with a defined anisotropy in any chosen direction with the potential to approaching magnetic properties of corresponding single crystalline materials.

36 MATERIALS SCIENCE↗

Advanced and functional composite materials via additive manufacturing: Trends and perspectives

Additive manufacturing (AM) has many advantages over conventional subtractive manufacturing methods. The cost-effective AM allows for precise fabrication of complex structures with less material waste, making it a popular manufacturing process in many applications. The recent development of AM materials has advanced significantly. Further, by precisely controlling material distribution and microstructural features, AM facilitates the creation of new composites with specific requirements. AM techniques have contributed considerably to integrating unique functionalities for various applications. This review emphasizes multiple categories of materials, including metal alloys, polymer-based composites, and sustainable composites, as well as applications of sensing materials and strategies and emerging artificial intelligence and machine learning.

36 MATERIALS SCIENCE↗

Neutron Characterization of Additively Manufactured Components. Workshop Report

Additive manufacturing (AM) is a collection of promising manufacturing methods that industry is beginning to explore and adopt. Macroscopically complicated and near net shape components are being built using AM, but how the material behaves in service is a big question for industry. Consequently, AM components/materials need further research into exactly what is made and how it will behave in service. This one and a half day workshop included a series of invited presentations from academia, industry and national laboratories (see Appendix A for the workshop agenda and list of talks). The workshop was welcomed by Alan Tennant, Chief Scientist, Neutron Sciences Directorate, ORNL, and opened remotely by Rob Ivestor, Deputy Director, Advanced Manufacturing Office-DOE, who declared AM adoptees as titans who will be able to create customized 3-D structures with 1 million to 1 billion micro welds with locally tailored microstructures. Further he stated that characterization with neutrons is key to be able to bring critical insight/information into the AM process/property/behavior relationship. Subsequently, the presentations spanned a slice of the current state of the art AM techniques and many of the most relevant characterization techniques using neutrons. After the talks, a panel discussion was held; workshop participants (see Appendix B for a list of attendees) providing questions and the panel answers. The main purpose of the panel discussion was to build consensus regarding the critical research needs in AM that can be addressed with neutrons. These needs were placed into three categories: modes of access for neutrons, new capabilities needed, new AM material issues and neutrons. Recommendations from the workshop were determined based on the panel discussion.

Watkins, Thomas R.↗

Additive Manufacturing Overview

What is additive manufacturing (AM)? A type of material creation that uses technology to create 3D objects layer by layer. Many materials can be used, including plastics and metals.

36 MATERIALS SCIENCE↗

Quantification of Powder Spreading Process for Metal Additive Manufacturing

In powder bed additive manufacturing (AM), the powder spreading process can lead to inhomogeneity in layer height, porosity level, and particle size distribution. Hence, creating homogeneous layers is the first task for optimal printing. The conventional assessment methods for powder quality are limited to a measurement of powder morphology, flowability, particle size distribution, surface roughness, and packing density. However, those techniques may not be the most appropriate to quantify the powder bed characteristics since it is not able to capture local particle configuration and does not provide any vectoral information (e.g., arrangement of contacts between particles during spreading). In this project, we: 1) developed a powder spreading model using discrete element method (DEM) for multiple-layered process, 2) experimentally measure powder spreading dynamics including static angle of repose (AOR) and dynamic AOR in order to calibrate and subsequently validate the model, and 3) investigated the effect of particle spreading process parameters on spatial powder bed structure and quality using scalar (e.g., porosity, surface roughness, coordination number, and particle size distribution) and tensorial (e.g., directionality of inter-particle contacts) methods for a comprehensive quantification of powder bed.

36 MATERIALS SCIENCE↗

Backshell Thermal Protection Materials for Additive Manufacturing

NASA invests in additive manufacturing (AM) to enable new mission architectures and design methods, including autonomous fabrication. AM is suited for backshell thermal protection materials that require many complex closeouts that lead to integration challenges. Current work will review printable backshell thermal protection material formulation, development, and characterization, such as Arc-jet testing results.

Tane Boghozian↗

Laser pulse shaping for additive manufacturing

A system for additive manufacturing uses a pulsed laser beam with one or more low flux components on the order of kW/cm2, and one or more high flux components on the order of MW/cm2 during the duration of the pulse. The pulsed laser beam is directed onto the powder particles on the substrate thereby melting the powder particles and melting the substrate at the interface layer between the powder and the substrate such that the powder particles bond to the substrate. This is accomplished by using low power (and low cost) lasers to do the majority of the energy transfer, and using high power (and higher cost) lasers to complete the melting process, overcoming the kinetics of powder agglomeration through surface tension forces by partially melting the powder-substrate interface layer before surface tension can take effect on the molten powder particles.

36 MATERIALS SCIENCE↗