Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Active target”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS2025

Components Refurbishment and Chemical Analysis Facility, SWMU #041 - Per- and Polyfluoroalkyl Substances Site Assessment Report Kennedy Space Center, Florida

This PFAS Site Assessment (SA) Report presents the activities and results associated with PFAS investigations at the Components Refurbishment and Chemical Analysis (CRCA) facility located at Kennedy Space Center (KSC), Florida. In 2022, CRCA was identified as an Area of Potential Concern because the facility stores several potential PFAS-containing chemicals. A groundwater sample collected from an onsite monitoring well detected PFOA and PFOS at concentrations greater than State of Florida provisional Groundwater Cleanup Target Levels (pGCTLs). PFAS SA activities were conducted between March 2022 and February 2024. During this timeframe, a total of 16 direct-push technology (DPT) locations and 82 discrete samples were collected from these locations, along with 90 monitoring well samples. The analytical data screening process focused on State of Florida pGCTLs and United States Environmental Protection Agency (USEPA) Regional Screening Level (RSLs) from November 2023 to evaluate the data. Analytical results identified PFOS, PFOA, and PFBA at concentrations exceeding their respective RSLs at each depth interval (shallow, intermediate, and deep). PFOS and PFOA had the largest footprint of RSL exceedances in each depth interval, but pGCTL exceedances were only observed at limited locations in the shallow and intermediate intervals. PFBA had the highest detections of any PFAS compound, with concentrations exceeding 180,000 nanograms per liter (ng/L), which is 100-times the RSL of 1,800 ng/L in the shallow and intermediate intervals and 10-times the RSL in the deep interval. The maximum PFBA detection was 841,000 ng/L at shallow monitoring well, MW0006. The PFAS SA also included samples collected from the onsite hydraulic containment system (HCS) which was installed to control and treat the onsite chlorinated volatile organic compound (CVOC) plume. Influent and effluent aqueous samples were collected monthly from the system. PFAS concentrations were relatively the same for both influent and effluent samples, indicating that while the HCS has been effective for CVOC treatment, it does not provide any additional treatment for PFAS compounds. Since the HCS has achieved its objectives, the system was shut down in December 2024. PFAS data gaps still exist, to include surface water and soil, which were not sampled during this SA. Soil sampling near the Chemical Process Area is recommended. Surface water and soil sampling at select stormwater outfalls is also recommended. Additionally, further groundwater sampling is recommended (DPT and monitoring well) in all depth intervals to delineate the extent of PFAS impacts at CRCA.

K Alex Murphy↗
DOE OSTI2024

Development of ceria-supported metal-oxide (MO x /CeO 2 ) catalysts via a one-pot chemical vapor deposition (OP-CVD) technique: Structure and reverse water gas shift reaction study

Current synthesis techniques for metal oxide (MO x )-supported catalysts have certain limitations of undesired target loading, ineffective dispersion of active species over the surface, uncontrolled particle size of active species, and complicated synthesis steps. Here, we developed a one-pot chemical vapor deposition (OP-CVD) methodology; by using which a solid metal precursor forms a vapor in a controlled condition and gets supported over the surrounding matrix. The theoretical stability followed by experimental validation using TGA is crucial for selecting the metal precursors. Three simple steps viz. premixing, dispersion, and rapid fixation by calcination are involved in the catalyst development via the OP-CVD approach. This study solely focused on the synthesis of 3d transition MO x over ceria support. The physicochemical characterizations of the prepared catalysts were performed by XRD, ICP-OES, SEM-EDX, CO pulse chemisorption, XANES, and EXAFS analyses to understand the crystal structure of involved species, target metal loading, dispersion, and particle size and prove the feasibility and viability of OP-CVD. The prepared catalysts were further tested for reverse water gas shift (RWGS) reaction to link their structural information with activity. The RWGS reaction data showed that the CO activity and CO selectivity were metal - and metal precursor-dependent. Higher CO activity of > 0.1 mol/h g-cat was observed for Cu and Co-based catalysts, with CO selectivity of ~100 %. This study provides an opportunity to produce efficient supported catalysts in a convenient way, providing effective catalytic activity.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Production of High Specific Activity 155 Tb, 161 Tb and 203 Pb for Research and Clinical Applications: Effective Target Design, Target Material Recycling and Radioisotope Separation (Final Technical Report)

The overall objectives of this project were (1) to develop methods for the production and separation of a diagnostic and therapeutic or “theranostic” pair of radioisotopes, terbium-155 ( 155 Tb) and terbium-161 ( 161 Tb) and (2) to train graduate students and postdoctoral fellows in technologies and methods used in radionuclide production. Radionuclides can be incorporated into drugs called radiopharmaceuticals that target a specific disease (e.g., cancer). The need for theranostic radionuclides is escalating with the clinical translation of radiopharmaceuticals due to their implementation in personalized medicine, which has demonstrated enhanced patient treatments. High purity and high specific activity radionuclides are critical for theranostic agent development, for example to maintain diagnostic image quality, to minimize radiation dose to the patient, and to increase uptake in the targeted tissue (e.g., tumor), especially in the case of receptor- and antigen-targeted agents. The 155 Tb (diagnostic) and 161 Tb (therapeutic) radioisotopes that were generated through this project are a theranostic pair with demonstrated potential for the development and translation into individualized, targeted, and dosimetry-driven radiotherapies. However, the development of such radiotherapies has been hindered by the lack of a routine and reliable supply of these isotopes in the United States. Methods for the production, separation, and supply of 155 Tb and 161 Tb were investigated and developed in this project. Further, the strong emphasis throughout the project on the training of graduate students and postdoctoral fellows has helped to ensure and enhance the nuclear science workforce through the training of the next generation of highly qualified scientists in nuclear and radiochemistry. This grant also continued a collaboration between scientists at the University of Washington (UW), the University of Missouri (MU) and Brookhaven National Laboratory (BNL). All three institutions were involved in the project, but to different degrees on the various tasks through which the overall objectives were met.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2023

A Telomerase-Activated Magnetic Resonance Imaging Probe for Consecutively Monitoring Tumor Growth Kinetics and In Situ Screening Inhibitors

Telomerase has long been considered as a biomarker for cancer diagnosis and a therapeutic target for drug discovery. Detecting telomerase activity in vivo could provide more direct information of tumor progression and response to drug treatment, which, however, is hampered by the lack of an effective probe that can generate an output signal without a tissue penetration depth limit. Here in this study, using the principle of distance-dependent magnetic resonance tuning, we constructed a telomerase-activated magnetic resonance imaging probe (TAMP) by connecting superparamagnetic ferroferric oxide nanoparticles (SPFONs) and paramagnetic Gd-DOTA (Gd(III) 1,4,7,10- tetraazacyclododecane-1,4,7,10-tetraazacyclododecane-1,4,7,10-tet-raacetic acid) complexes via telomerase-responsive DNA motifs. Upon telomerase-catalyzed extension of the primer in TAMP, Gd-DOTA-conjugated oligonucleotides can be liberated from the surface of SPFONs through a DNA strand displacement reaction, restoring the T 1 signal of the Gd-DOTA for a direct readout of the telomerase activity. Here we show that, by tracking telomerase activity, this probe provides consistent monitoring of tumor growth kinetics during progression and in response to drug treatment and enables in situ screening of telomerase inhibitors in whole-animal models. This study provides an alternative toolkit for cancer diagnosis, treatment response assessment, and anticancer drug screening.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Modernization of ORIGEN Library Creation in the SCALE Computer Code

The modernization of SCALE features has been a target for recent SCALE releases. ORIGEN, the activation and depletion code in SCALE, is one such legacy code that has been targeted for modernization. A part of these modernization efforts has been to develop capabilities within ORIGEN to directly read ENDF-formatted data files. In addition, the input format for the COUPLE library creation utility was rewritten to a format more accessible to newer SCALE users. Finally, the ability of COUPLE to create ORIGEN libraries without sublibrary data has been added.KEYWORDS: ORIGEN, depletion, SCALE, API

Hart, Shane↗
DOE OSTI2021

Evolutionary Diversification of Host-Targeted Bartonella Effectors Proteins Derived from a Conserved FicTA Toxin-Antitoxin Module

Proteins containing a FIC domain catalyze AMPylation and other post-translational modifications (PTMs). In bacteria, they are typically part of FicTA toxin-antitoxin modules that control conserved biochemical processes such as topoisomerase activity, but they have also repeatedly diversified into host-targeted virulence factors. Among these, Bartonella effector proteins (Beps) comprise a particularly diverse ensemble of FIC domains that subvert various host cellular functions. However, no comprehensive comparative analysis has been performed to infer molecular mechanisms underlying the biochemical and functional diversification of FIC domains in the vast Bep family. Here, we used X-ray crystallography, structural modelling, and phylogenetic analyses to unravel the expansion and diversification of Bep repertoires that evolved in parallel in three Bartonella lineages from a single ancestral FicTA toxin-antitoxin module. Our analysis is based on 99 non-redundant Bep sequences and nine crystal structures. Inferred from the conservation of the FIC signature motif that comprises the catalytic histidine and residues involved in substrate binding, about half of them represent AMP transferases. A quarter of Beps show a glutamate in a strategic position in the putative substrate binding pocket that would interfere with triphosphate-nucleotide binding but may allow binding of an AMPylated target for deAMPylation or another substrate to catalyze a distinct PTM. The β-hairpin flap that registers the modifiable target segment to the active site exhibits remarkable structural variability. The corresponding sequences form few well-defined groups that may recognize distinct target proteins. The binding of Beps to promiscuous FicA antitoxins is well conserved, indicating a role of the antitoxin to inhibit enzymatic activity or to serve as a chaperone for the FIC domain before translocation of the Bep into host cells. Taken together, our analysis indicates a remarkable functional plasticity of Beps that is mostly brought about by structural changes in the substrate pocket and the target dock. These findings may guide future structure–function analyses of the highly versatile FIC domains.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Host analysis-guided selection and targeted engineering (HASTE) of Lipomyces tetrasporus for the conversion of CO2-derived feedstocks

Efficient and cost-competitive bioproduction calls for utilizing CO2-derived feedstocks, such as products from electro-reduction of CO2 and hydrolysate from lignocellulosic biomass. However, efficiently using all their carbon components, including acetate, glucose, and xylose, remains a challenge. Here, we characterize Lipomyces tetrasporus, a novel, robust yeast strain capable of effectively assimilating these carbon sources. We used an integrated systems biology approach combining ¹³C metabolic flux analysis, dynamic labeling experiments, and RNA sequencing. We conducted the first metabolic flux analysis for glucose, xylose, and acetate catabolism in this species. Dynamic labeling revealed a highly active TCA cycle during acetate metabolism, evidenced by rapid citrate and malate accumulation. The strain demonstrated strong NADH/NADPH production and acetyl-CoA synthase activity. Using insights and gene targets from this analysis, we engineered L. tetrasporus for malate production. The engineered strain produced 7.5 g/L malic acid (0.25 g/g yield) in shake flasks with glucose-acetate media and 28.8 g/L malic acid at a yield of 0.20 g/g in fed-batch mode with corn-stover hydrolysate. Together, these insights and rational strain engineering establish L. tetrasporus as a versatile, Crabtree-negative platform that is an energy-CO2-bioproduction nexus for channeling CO2 carbon into value-added bioproducts.

Xiao, Zhengyang↗
DOE OSTI2023

Targeted curation of the gut microbial gene content modulating human cardiovascular disease

Despite the promise of the gut microbiome to predict human health, few studies expose the molecular-scale processes underpinning such forecasts. We mined over 200,000 gut-derived genomes from cultivated and uncultivated microbial lineages to inventory the gut microorganisms and their gene content that control trimethylamine-induced cardiovascular disease. We assigned an atherosclerotic profile to the 6,341 microbial genomes that encoded metabolisms associated with heart disease, creating the Methylated Amine Gene Inventory of Catabolism database (MAGICdb). From microbiome gene expression data sets, we demonstrate that MAGICdb enhanced the recovery of disease-relevant genes and identified the most active microorganisms, unveiling future therapeutic targets. From the feces of healthy and diseased subjects, we show that MAGICdb predicted cardiovascular disease status as effectively as traditional lipid blood tests. This functional microbiome catalog is a public, exploitable resource, designed to enable a new era of microbiota-based therapeutics and diagnostics

metatranscriptomics↗
NASA NTRSDate not supplied

A Historical Overview of the NASA Orbital Debris Program Office’s Laboratory Optical Measurements

The NASA Orbital Debris Program Office (ODPO) has used laboratory measurements to help bring ground-based measurements together with models to ascertain Earth-orbiting target parameters of interest to support various orbital debris models. In 2005, the Optical Measurement Center (OMC) was established to simulate space-based illumination conditions using equipment and techniques that recreate telescopic observations, particularly source-target-sensor orientations. The intent was to recreate light curves using known aspect angles of known targets and phase angles (angle is defined by the vertex between illumination source-object-detector) to complement telescopic observations that could be used to update the current optical size estimation model (OSEM) – a model that converts object brightness into size for orbital debris models. To support the above goals, the laboratory has undergone several equipment upgrades to increase capabilities over almost 20 years of operation. The primary instrumentation acquires reflectance measurements and includes a solar-like light source, CCD camera with astrometric filters, and robotic arm. A rotary arm was added approximately five years after full operation to allow acquisition through a full 360° range of phase angles. Another part of the OMC instrumentation is a field spectrometer, predominately used for field operations to acquire pre- and post-flight spacecraft material spectral measurements. Additionally, reflectance spectroscopy of various materials is also of interest resulting from hypervelocity impact tests, pristine spacecraft materials, or samples of materials that are used in spacecraft design. These measurements are stored in NASA’s Spectral Material Database, a resource that is still being populated today. The study of spectral measurements also enabled the development of spectral unmixing routines to support the identification of spacecraft materials from spectral data gathered by ground based telescopes. Preliminary OMC investigations focused on feasibility studies to acquire 360° rotation light curves of simple shapes at a single-phase angle and extended to measurements of representative fragments from ground-based explosion tests. To correlate the light curves with ground-based optical measurements, a focused study on high area to mass materials was conducted in support of a newly identified population (at the time) in geosynchronous orbit (GEO) consisting of multi-layered insulation. To further characterize orbital debris, a larger selection of materials was analyzed using laboratory photometric measurements that included representative targets from pristine spacecraft materials and ground-based impact tests. Around 2012, an initiative was requested to understand the feasibility of active debris removal (ADR) of larger targets using grappling methods for spent rocket bodies. Using a priori information on selected targets, scaled-down versions of rocket bodies were generated thanks to improvements in 3D printing technology and machining. These targets were studied in the OMC to understand rotation characteristics. These were compared with telescopic data to determine if the tumble and rotation angles would allow ADR. In 2013, the OMC focused on combining spectral measurements with photometric data to characterize GEO orbital debris. Several years later, NASA acquired a Titan III Transtage test article from “The Boneyard” with a high-resemblance to on-orbit Titan III Transtage rocket bodies, allowing physical access to a representative rocket body that suffered fragmentations in GEO. This prompted the creation of 3D models using lidar technology and spectral measurements of the materials. Focused research also transitioned to specific materials (i.e., solar cells) when telescopic surveys requested characterization of specific GEO targets. In the different research products presented, the focus has been to understand the various parameters that influence optical size estimation, including albedo, phase functions, and brightness variations. Work in this area continues with newer sources of data, including DebriSat, a high-fidelity 56-kg spacecraft replica representative of a modern low Earth orbit (LEO) satellite subjected to a laboratory hypervelocity impact test to understand fragmentation events and to support updates to satellite breakup models and size estimation models. Utilizing the vast population of fragments from DebriSat and prior laboratory impact experiments, the ODPO has focused on acquiring bidirectional reflectance distribution function (BRDF) data to characterize targets in the laboratory, thus removing aspect angle dependencies. Additionally, the DebriSat project has provided improved processes for measuring size via image acquisition, such that a true fragment size can be directly compared to the derived size using the OSEM. The team continues to assess BRDFs and use spectral measurement data to investigate the parameters used in the OSEM, specifically magnitudes, albedo, and phase functions.

Heather Cowardin↗
DOE OSTI2025

The 200 Gbps Challenge: Imagining HL-LHC analysis facilities

The IRIS-HEP software institute, as a contributor to the broader HEP Python ecosystem, is developing scalable analysis infrastructure and software tools to address the upcoming HL-LHC computing challenges with new approaches and paradigms, driven by our vision of what HL-LHC analysis will require. The institute uses a "Grand Challenge" format, constructing a series of increasingly large, complex, and realistic exercises to show the vision of HL-LHC analysis. Recently, the focus has been demonstrating the IRIS-HEP analysis infrastructure at scale and evaluating technology readiness for production. As a part of the Analysis Grand Challenge activities, the institute executed a "200 Gbps Challenge", aiming to show sustained data rates into the event processing of multiple analysis pipelines. The challenge integrated teams internal and external to the institute, including operations and facilities, analysis software tools, innovative data delivery and management services, and scalable analysis infrastructure. The challenge showcases the prototypes - including software, services, and facilities - built to process around 200 TB of data in both the CMS NanoAOD and ATLAS PHYSLITE data formats with test pipelines. The teams were able to sustain the 200 Gbps target across multiple pipelines. The pipelines focusing on event rate were able to process at over 30 MHz. These target rates are demanding; the activity revealed considerations for future testing at this scale and changes necessary for physicists to work at this scale in the future. The 200 Gbps Challenge has established a baseline on today's facilities, setting the stage for the next exercise at twice the scale.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1999

Contribution of the cerebellar flocculus to gaze control during active head movements

The flocculus and ventral paraflocculus are adjacent regions of the cerebellar cortex that are essential for controlling smooth pursuit eye movements and for altering the performance of the vestibulo-ocular reflex (VOR). The question addressed in this study is whether these regions of the cerebellum are more globally involved in controlling gaze, regardless of whether eye or active head movements are used to pursue moving visual targets. Single-unit recordings were obtained from Purkinje (Pk) cells in the floccular region of squirrel monkeys that were trained to fixate and pursue small visual targets. Cell firing rate was recorded during smooth pursuit eye movements, cancellation of the VOR, combined eye-head pursuit, and spontaneous gaze shifts in the absence of targets. Pk cells were found to be much less sensitive to gaze velocity during combined eye-head pursuit than during ocular pursuit. They were not sensitive to gaze or head velocity during gaze saccades. Temporary inactivation of the floccular region by muscimol injection compromised ocular pursuit but had little effect on the ability of monkeys to pursue visual targets with head movements or to cancel the VOR during active head movements. Thus the signals produced by Pk cells in the floccular region are necessary for controlling smooth pursuit eye movements but not for coordinating gaze during active head movements. The results imply that individual functional modules in the cerebellar cortex are less involved in the global organization and coordination of movements than with parametric control of movements produced by a specific part of the body.

NASA Discipline Neuroscience↗
NASA NTRS1994

Experiment K-7-31: Studies of Vestibular Primary Afferents and Eye Movements in Normal, Hypergravity and Hypogravity - Axon Cosmos Flight 2044

Fourteen days of active head movements in microgravity appear to modify the gain and neural adaptation properties of the horizontal semicircular canals in the rhesus monkey. This is the first demonstration of adaptive plasticity in the sensory receptor. Reversing prisms, for example, do not modify the gain of the primary afferent response. Pulse yaw rotation, sinusoidal rotation, and sum of sinusoidal rotation testing during the first day following recovery revealed that the gain of a sample of afferents was significantly greater than the gain derived from afferent responses obtained during pre-flight and control monkey testing. There was no strong evidence of tilt sensitivity in the sample of afferents that we tested either during the pre-flight or control tests or during the first day post-flight. Two irregular afferents tested on postflight day 2 showed changes with tilt but the responses were not systematic. The spontaneous discharge did not change following flight. Mean firing rate and coefficient of variation remained constant during the post flight tests and was near the value measured during pre flight tests. The change in gain of horizontal canal afferents might be adaptive. The animals were required to look at a target for food. This required active head and eye movements. Active head movements have been shown to be hypometric and eye movements have been shown to be hypermetric during the first few days of past Cosmos flights (see introduction). It might be that the increased gain in the horizontal semicircular canals permit accurate target acquisition during hypometric head movements by driving the eyes to greater angles for smaller angles of head movement. The mechanism by which the semicircular canals recalibrate (increase their gain) is unknown. The efferent vestibular system is a logical candidate. Horizontal nystagmus during rotation about an earth vertical axis with the horizontal semicircular canals in the plane of rotation produced the same response during postflight day 1 and post-flight day 9. But when the head was pitched down 45? the nystagmus slow phase velocity was greater and the duration was about twice during post-flight day 1. Apparently, this response involving the interaction of the horizontal and vertical semicircular canals and the otoliths did not recalibrate during post-flight day 1. The 'DC' bias of the slow phase velocity of the horizontal nystagmus during constant velocity horizontal axis rotation was roughly 4 times for one flight monkey and roughly 2 times for the other on post-flight day 1 compared to post-flight day 9. These results suggest that the otolith mediated response during constant velocity rotation also did not recalibrate on post-flight day 1.

Correia, M. J.↗
NASA NTRS1991

Concurrent-scene/alternate-pattern analysis for robust video-based docking systems

A typical docking target employs a three-point design of retroreflective tape, one at each endpoint of the center-line, and one on the tip of the central post. Scenes, sensed via laser diode illumination, produce pictures with spots corresponding to desired reflection from the retroreflectors and other reflections. Control corrections for each axis of the vehicle can then be properly applied if the desired spots are accurately tracked. However, initial acquisition of these three spots (detection and identification problem) are non-trivial under a severe noise environment. Signal-to-noise enhancement, accomplished by subtracting the non-illuminated scene from the target scene illuminated by laser diodes, can not eliminate every false spot. Hence, minimization of docking failures due to target mistracking would suggest needed inclusion of added processing features pertaining to target locations. In this paper, we present a concurrent processing scheme for a modified docking target scene which could lead to a perfect docking system. Since the non-illuminated target scene is already available, adding another feature to the three-point design by marking two non-reflective lines, one between the two end-points and one from the tip of the central post to the center-line, would allow this line feature to be picked-up only when capturing the background scene (sensor data without laser illumination). Therefore, instead of performing the image subtraction to generate a picture with a high signal-to-noise ratio, a processed line-image based on the robust line detection technique (Hough transform) can be used to fuse with the actively sensed three-point target image to deduce the true locations of the docking target. This dual-channel confirmation scheme is necessary if a fail-safe system is to be realized from both the sensing and processing point-of-views. Detailed algorithms and preliminary results are presented.

Udomkesmalee, Suraphol↗
NASA NTRS1991

Autonomous docking ground demonstration

The Autonomous Docking Ground Demonstration is an evaluation of the laser sensor system to support the docking phase (12 ft to contact) when operated in conjunction with the guidance, navigation, and control (GN&C) software. The docking mechanism being used was developed for the Apollo/Soyuz Test Program. This demonstration will be conducted using the 6-DOF Dynamic Test System (DTS). The DTS simulates the Space Station Freedom as the stationary or target vehicle and the Orbiter as the active or chase vehicle. For this demonstration, the laser sensor will be mounted on the target vehicle and the retroflectors will be on the chase vehicle. This arrangement was chosen to prevent potential damage to the laser. The laser sensor system, GN&C, and 6-DOF DTS will be operated closed-loop. Initial conditions to simulate vehicle misalignments, translational and rotational, will be introduced within the constraints of the systems involved.

Lamkin, Steve L.↗
NASA NTRS1991

Autonomous docking ground demonstration (category 3)

The NASA Johnson Space Center (JSC) is involved in the development of an autonomous docking ground demonstration. The demonstration combines the technologies, expertise and facilities of the JSC Tracking and Communications Division (EE), Structures and Mechanics Division (ES), and the Navigation, Guidance and Control Division (EG) and their supporting contractors. The autonomous docking ground demonstration is an evaluation of the capabilities of the laser sensor system to support the docking phase (12ft to contact) when operated in conjunction with the Guidance, Navigation and Control Software. The docking mechanism being used was developed for the Apollo Soyuz Test Program. This demonstration will be conducted using the Six-Degrees of Freedom (6-DOF) Dynamic Test System (DTS). The DTS environment simulates the Space Station Freedom as the stationary or target vehicle and the Orbiter as the active or chase vehicle. For this demonstration the laser sensor will be mounted on the target vehicle and the retroreflectors on the chase vehicle. This arrangement was used to prevent potential damage to the laser. The sensor system. GN&C and 6-DOF DTS will be operated closed-loop. Initial condition to simulate vehicle misalignments, translational and rotational, will be introduced within the constraints of the systems involved. Detailed description of each of the demonstration components (e.g., Sensor System, GN&C, 6-DOF DTS and supporting computer configuration) including their capabilities and limitations will be discussed. A demonstration architecture drawing and photographs of the test configuration will be presented.

Lamkin, Steve L.↗
NASA NTRS2011

Efficient Spectral Endmember Detection Onboard the EO-1 Spacecraft

Spaceflight and planetary exploration place severe constraints on the available bandwidth for downlinking large hyperspectral images. In addition, communications with spacecraft often occur intermittently, so mission-relevant hyperspectral data must wait for analysis on the ground before it can inform spacecraft activity planning. Onboard endmember detection can help alleviate these problems. It enables novelty detection and target identification for scheduling follow-up activities such as additional observation by narrow field of view instruments. Additionally, endmember analysis can facilitate data summary for downlink. This work describes a planned experiment of selective downlink by the EO-1 autonomous spacecraft. Here an efficient superpixel endmember detection algorithm keeps to the limited computational constraints of the flight processor. Tests suggest the procedure could enable significant improvements in downlink efficiency.

Endmember Detection↗
DOE OSTI2022

Ordered CoPt oxygen reduction catalyst with high performance and durability

A high-performance and durable polymer electrolyte membrane fuel cell cathode catalyst composed of an ordered L10–CoPt core and a thin Pt shell was designed and prepared. Under practical fuel cell membrane electrode assembly testing conditions, the cathode catalyst showed an outstanding initial mass activity of 0.6 A/mgPt, which satisfies the U.S. Department of Energy performance target while also meeting the durability target of less than 40% loss in mass activity after 30,000 accelerated stress test voltage cycles. The high structural stability of the L10–CoPt@Pt-shell catalyst was confirmed by postmortem materials characterization, and the origin of this robustness was revealed by density functional theory calculations, where the barriers for diffusion of Co atoms were observed to be significantly increased in the ordered intermetallic core.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

2'-O methylation of RNA cap in SARS-CoV-2 captured by serial crystallography

The genome of the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) coronavirus has a capping modification at the 5'-untranslated region (UTR) to prevent its degradation by host nucleases. These modifications are performed by the Nsp10/14 and Nsp10/16 heterodimers using S-adenosylmethionine as the methyl donor. Nsp10/16 heterodimer is responsible for the methylation at the ribose 2'-O position of the first nucleotide. To investigate the conformational changes of the complex during 2'-O methyltransferase activity, we used a fixed-target serial synchrotron crystallography method at room temperature. We determined crystal structures of Nsp10/16 with substrates and products that revealed the states before and after methylation, occurring within the crystals during the experiments. Here we report the crystal structure of Nsp10/16 in complex with Cap-1 analog ( m7 GpppA m2'-O ). Inhibition of Nsp16 activity may reduce viral proliferation, making this protein an attractive drug target.

59 BASIC BIOLOGICAL SCIENCES↗