Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AERODYNAMICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Aerodynamic loss generation in a low-pressure turbine stage with high lift blading

The present work aims to investigate the loss generation mechanisms in a highly loaded low-pressure turbine (LPT) stage. The turbine employs high-lift airfoils to reduce the number of blades and therefore the overall engine weight. Large Eddy Simulation (LES) is applied to study the detailed flow fields at two representative Reynolds numbers (150,000 and 40,000). The calculated flow fields are compared with available measured data. LES calculates the measured aerodynamic performance of the current turbine stage well. Both the measurements and the CFD simulations indicate that most of the aerodynamic loss is generated by the development of secondary flows near the rotor hub. An area of low momentum and high aerodynamic loss forms at roughly 25 % span above the hub downstream of the rotor. Formation and migration of a vortex system near the hub is the primary source of the loss generation. The hub wall vortex system in this highly loaded turbine stage is quite different from the horse-shoe vortex system in a typical stationary turbine cascade. Calculated instantaneous and time-averaged flow fields at two Reynolds numbers are examined in detail to study Reynolds number effects on the turbine stage performance. Steady and unsteady flow separation on the rotor suction side is calculated at both high and low Reynolds numbers. At the lower Reynolds number of 40,000, thicker blade boundary layers increase the area of flow separation on the rotor suction side, resulting in a 1.9 % increase in aerodynamic loss compared to the higher Reynolds number case.

low pressure turbine↗

An Overview of Ares-I CFD Ascent Aerodynamic Data Development And Analysis Based on USM3D

An overview of the computational results obtained from the NASA Langley developed unstructured grid, Reynolds-averaged Navier-Stokes flow solver USM3D, in support of the Ares-I project within the NASA s Constellation program, are presented. The numerical data are obtained for representative flow conditions pertinent to the ascent phase of the trajectory at both wind tunnel and flight Reynolds number without including any propulsion effects. The USM3D flow solver has been designated to have the primary role within the Ares-I project in developing the computational aerodynamic data for the vehicle while other flow solvers, namely OVERFLOW and FUN3D, have supporting roles to provide complementary results for fewer cases as part of the verification process to ensure code-to-code solution consistency. Similarly, as part of the solution validation efforts, the predicted numerical results are correlated with the aerodynamic wind tunnel data that have been generated within the project in the past few years. Sample aerodynamic results and the processes established for the computational solution/data development for the evolving Ares-I design cycles are presented.

FUN3D↗

Unsteady aerodynamics of large-scale floating offshore wind turbines in surge motion

Unsteady aerodynamic loads significantly influence the design and wake flow field of floating offshore wind turbines, especially due to wave- or vibration-induced tower top motions triggering various unsteady phenomena. Recent studies show that increasing turbine sizes amplify unsteady aerodynamic effects, as their impact typically grows with rotor diameter. This work combines recent findings from experiments and simulations on model-scale FOWT aerodynamics with new numerical analyses of large-scale rotors, providing a comprehensive understanding of unsteady phenomena occurrence and impact. Numerical analyses of the IEA 15-MW and 22-MW rotors undergoing surge motions characterise the combined influence of motion-induced unsteady phenomena on rotor thrust. Results indicate that unsteady effects can reduce thrust force variations by up to 40% at realistic surge periods. These findings contrast with prior model-scale rotor investigations, attributed to the specialised design of the model rotors. Comparisons between numerical methods - the dynamic blade element momentum method in OpenFAST and free vortex wake modules in panMARE and OpenFAST - reveal persistent differences in thrust predictions under both idealised and realistic conditions. This highlights that classical blade element momentum approaches require enhancement to accurately capture unsteady loads on large-scale floating offshore wind turbines at low wind speeds.

16 TIDAL AND WAVE POWER↗

Insights Into the Aerodynamic Versus Radiometric Surface Temperature Debate in Thermal-Based Evaporation Modeling

Global evaporation monitoring from Earth observation thermal infrared satellite missions is historically challenged due to the unavailability of any direct measurements of aerodynamic temperature. State-of-the-art one-source evaporation models use remotely sensed radiometric surface temperature as a substitute for the aerodynamic temperature and apply empirical corrections to accommodate for their inequality. This introduces substantial uncertainty in operational drought mapping over complex landscapes. By employing a non-parametric model, we show that evaporation can be directly retrieved from thermal satellite data without the need of any empirical correction. Independent evaluation of evaporation in a broad spectrum of biome and aridity yielded statistically significant results when compared with eddy covariance observations. While our simplified model provides a new perspective to advance spatio-temporal evaporation mapping from any thermal remote sensing mission, the direct retrieval of aerodynamic temperature also generates the highly required insight on the critical role of biophysical interactions in global evaporation research.

54 ENVIRONMENTAL SCIENCES↗

Aerodynamic integration produces a vehicle shape with a negative drag coefficient

Negative drag coefficients are normally associated with a vessel outfitted with a sail to extract energy from the wind and propel the vehicle forward. Therefore, the notion of a heavy vehicle, that is, a semi truck, that generates negative aerodynamic drag without a sail or any external appendages may seem implausible, especially given the fact that these vehicles have some of the largest drag coefficients on the road today. However, using both wind tunnel measurements and computational fluid dynamics simulations, we demonstrate aerodynamically integrated vehicle shapes that generate negative body-axis drag in a crosswind as a result of large negative frontal pressures that effectively “pull” the vehicle forward against the wind, much like a sailboat. While negative body-axis drag exists only for wind yaw angles above a certain analytical threshold, the negative frontal pressures exist at smaller yaw angles and subsequently produce body-axis drag coefficients that are significantly less than those of modern heavy vehicles. The application of this aerodynamic phenomenon to the heavy vehicle industry would produce sizable reductions in petroleum use throughout the United States.

42 ENGINEERING↗

CME PROPAGATION: WHERE DOES AERODYNAMIC DRAG “TAKE OVER”?

We investigate the Sun–Earth dynamics of a set of eight well observed solar coronal mass ejections (CMEs) using data from the Solar Terrestrial Relations Observatory spacecraft. We seek to quantify the extent to which momentum coupling between these CMEs and the ambient solar wind (i.e., the aerodynamic drag) influences their dynamics. To this end, we use results from a 3D flux rope model fit to the CME data. We find that solar wind aerodynamic drag adequately accounts for the dynamics of the fastest CME in our sample. For the relatively slower CMEs, we find that drag-based models initiated below heliocentric distances ranging from 15 to 50 R{sub ⊙} cannot account for the observed CME trajectories. This is at variance with the general perception that the dynamics of slow CMEs are influenced primarily by solar wind drag from a few R{sub ⊙} onwards. Several slow CMEs propagate at roughly constant speeds above 15–50 R{sub ⊙}. Drag-based models initiated above these heights therefore require negligible aerodynamic drag to explain their observed trajectories.

79 ASTRONOMY AND ASTROPHYSICS↗

Distributed Aerodynamic Control using Active Trailing-Edge Flaps for Large Wind Turbines

This work presents a numerical framework to investigate distributed aerodynamic control devices for application in large wind turbines. Tool capabilities were extended to facilitate multiple aerodynamic polar tables. The airfoil aerodynamics characteristics were automatically determined, and blade-pitch, generator-torque, and trailing-edge-flap controllers were tuned in-the-loop according to a specific blade design. This automated workflow allows analysis and optimization of trailing-edge flaps, enabling codesign studies. Results targeted reductions of root-flap-bending moment derivatives. The applied trailing-edge-flap control reduced the standard deviation of root-flap-bending moments by more than 6% and benefit related parameters, e.g., reduce blade-tip deflections, by up to 8%. Because of varying thrust distributions along the blade span, different flap designs have nonlinear characteristics in terms of the control objective and show best performance when located at the radial position with maximum thrust. In general, larger flaps provide a greater influence to reduce the target control objective.

17 WIND ENERGY↗

A DNN surrogate unsteady aerodynamic model for wind turbine loads calculations

A recurrent deep-neural network (DNN) surrogate model capable of modeling the unsteady aerodynamic response and dynamic stall behavior of wind turbine blades has been developed and validated for use in engineering design codes. The model is trained using a subset of the oscillating airfoil experiments conducted at the Ohio State University wind tunnel. The predictions from our DNN model show excellent agreement with the measured data and, in all cases, a marked improvement over the state-of-the-art unsteady aerodynamic models. The DNN-based unsteady aerodynamics model was integrated with OpenFAST to perform full-turbine load computations for the NREL-5MW rotor. The largest differences are observed for the inboard stations, particularly in the pitching moment response, when using the new surrogate model compared to the other models available in OpenFAST.

17 WIND ENERGY↗

OC6 project Phase III: validation of the aerodynamic loading on a wind turbine rotor undergoing large motion caused by a floating support structure

Abstract. This paper provides a summary of the work done within Phase III of the Offshore Code Comparison Collaboration, Continued, with Correlation and unCertainty (OC6) project, under the International Energy Agency Wind Technology Collaboration Programme Task 30. This phase focused on validating the aerodynamic loading on a wind turbine rotor undergoing large motion caused by a floating support structure. Numerical models of the Technical University of Denmark 10 MW reference wind turbine were validated using measurement data from a 1:75 scale test performed during the UNsteady Aerodynamics for FLOating Wind (UNAFLOW) project and a follow-on experimental campaign, both performed at the Politecnico di Milano wind tunnel. Validation of the models was performed by comparing the loads for steady (fixed platform) and unsteady (harmonic motion of the platform) wind conditions. For the unsteady wind conditions, the platform was forced to oscillate in the surge and pitch directions under several frequencies and amplitudes. These oscillations result in a wind variation that impacts the rotor loads (e.g., thrust and torque). For the conditions studied in these tests, the system aerodynamic response was almost steady. Only a small hysteresis in airfoil performance undergoing angle of attack variations in attached flow was observed. During the experiments, the rotor speed and blade pitch angle were held constant. However, in real wind turbine operating conditions, the surge and pitch variations would result in rotor speed variations and/or blade pitch actuations, depending on the wind turbine controller region that the system is operating. Additional simulations with these control parameters were conducted to verify the fidelity of different models. Participant results showed, in general, a good agreement with the experimental measurements and the need to account for dynamic inflow when there are changes in the flow conditions due to the rotor speed variations or blade pitch actuations in response to surge and pitch motion. Numerical models not accounting for dynamic inflow effects predicted rotor loads that were 9 % lower in amplitude during rotor speed variations and 18 % higher in amplitude during blade pitch actuations.

17 WIND ENERGY↗

HYPERSONIC AERODYNAMIC PROBLEMS OF THE FUTURE

Blunt shapes were of interest for the speed regime of ballistic missiles and satellite vehicles, in the main, as a result of the necessity for minimizing convective heating. But as speeds exceed escape speed, the heating due to air radiation assumes an even more important role than does the convective heating. It is shown that this change revives interest in the more slender configurations and that when the speed of a vehicle entering the atmosphere of a planet becomes sufficiently great, it may be economical to decelerate in part by retrorocket rather than entirely by aerodynamic braking. The factors discussed determine the speed limit for which retrorocket braking becomes desirable. The change in the basic characteristics of flow brought about by gas radiation at speeds well in excess of escape speed are then analyzed. It is shown that when the gas radiation energy becomes a significant part of the total energy of the flow, it is no longer possible to analyze aerodynamic flow fields with the assumption that the energy of elemental volumes remains constant, since for such cases a transfer of energy by radiation from one elemental volume to another significantly alters the flow. The increase in complexity in the analytical approaches to the problems of these hypersonic flows necessitates, more than ever, continued experimental research, even though such experiments are exceedingly difficult to perform. Extension of our experimental knowledge of these hypersonic flows is shown to be possible by study of tracked trajectories of bright meteors. Some analyses of meteor tracking data are presented which demonstrate that the tracking camera systems employed at present can provide sufficiently accurate results to yield useful aerodynamic heating information.

SATELLITE↗

Aerodynamic Evidence Pertaining to the Entry of Tektites into the Earth's Atmosphere

Evidence is presented which shows that the Australian and Java tektites entered the earth's atmosphere and experienced ablation by severe aerodynamic heating in hypervelocity flight. The laboratory experiments on hypervelocity ablation have reproduced ring-wave flow ridges and coiled circumferential flanges like those found on certain of these tektites. Systematic striae distortions exhibited in a thin layer beneath the front surface of australites also are reproduced in the laboratory ablation experiments, and are shown to correspond to the calculated distortions for aerodynamic ablation of a glass. About 98 percent of Australian tektites represent aerodynamically stable configurations during the ablative portion of an entry trajectory. Certain meteorites exhibit surface features similar to those on tektites.

AERODYNAMIC HEATING↗

II. Aerodynamic research relative to variable-sweep multimission aircraft

The development of a multimission military aircraft would be highly desirable both from the standpoint of easing the strain on the national budget by reducing the number of aircraft types and of providing versatility which would increase the effectiveness of the aircraft in the performance of a given mission. Some of the capabilities which might be required of such an aircraft are shown in figure 1 along with their respective aerodynamic and configuration requirements. The first three capabilities are grouped together since they all require good subsonic characteristics. The first, a long loiter capability for combat air patrol and the second, a long ferry range for efficient aircraft deployment both require a high subsonic lift-drag ratio. The third capability, STOL, is desirable for carrier and short-field operation and requires the development of high lift. All three of these capabilities can best be obtained with a high-aspect-ratio wing having a large span and a low-sweep angle. The fourth capability is that of a high-altitude supersonic attack or intercept and requires a high lift-drag ratio at supersonic speeds which dictates a rather slender configuration with a moderate-span wing which is either very thin or highly swept. The fifth capability listed in figure 1 is that of a low-altitude high-speed attack that would increase the probability of long-range penetration of antiaircraft defenses. The high dynamic pressures encountered on the deck at high speeds require a low-lift-curve slope to reduce the gust-induced normal accelerations, and low friction and wave drag (drag due to lift is insignificant at high dynamic pressures) to assure sufficient speed and range. In order to best satisfy these requirements, a slender aircraft having little or no wing is required. It is apparent from figure 1 that these five capabilities are highly incompatible and that an efficient multimission aircraft will require a means of varying its aerodynamic characteristics. This can be best accomplished with some type of variable-wing geometry. There are, of course, several types of variable wing geometry. However, in view of the extremely large variations in wing span desired, variable wing sweep, as indicated In the lower right sketch of figure 1, appears to provide the best method. The Langley Research Center of the National Aeronautics and Space Administration has therefore initiated a research program to provide the aerodynamic information needed for the development of a variable-sweep multimission military aircraft, and it is the purpose of this paper to briefly describe some of the results of this program.

Military aircraft↗

Effect of Ground Interference on the Aerodynamic Characteristics of a 42 Degrees Sweptback Wing

The effects of ground interference on the aerodynamic characteristics of a 42 degrees sweptback wing have been determined at distances above the ground 0.68 and 0.92 of the mean aerodynamic chord (measured from the 0.25 mean aerodynamic chord). The wing was tested without flaps and with inboard trailing-edge split and outboard leading-edge flaps deflected. The wing had an aspect ratio of 4, a taper ratio of 0.625, and NACA 641-112 airfoil sections perpendicular to the 0.273 chord line. The results are, in general, comparable to those reported for unswept wings. The longitudinal stability at the stall was not materially affected at the ground heights of the present tests.

RESEARCH TECHNIQUE, AERODYNAMICS↗

Error Estimate of the Ares I Vehicle Longitudinal Aerodynamic Characteristics Based on Turbulent Navier-Stokes Analysis

Numerical predictions of the longitudinal aerodynamic characteristics for the Ares I class of vehicles, along with the associated error estimate derived from an iterative convergence grid refinement, are presented. Computational results are based on the unstructured grid, Reynolds-averaged Navier-Stokes flow solver USM3D, with an assumption that the flow is fully turbulent over the entire vehicle. This effort was designed to complement the prior computational activities conducted over the past five years in support of the Ares I Project with the emphasis on the vehicle s last design cycle designated as the A106 configuration. Due to a lack of flight data for this particular design s outer mold line, the initial vehicle s aerodynamic predictions and the associated error estimates were first assessed and validated against the available experimental data at representative wind tunnel flow conditions pertinent to the ascent phase of the trajectory without including any propulsion effects. Subsequently, the established procedures were then applied to obtain the longitudinal aerodynamic predictions at the selected flight flow conditions. Sample computed results and the correlations with the experimental measurements are presented. In addition, the present analysis includes the relevant data to highlight the balance between the prediction accuracy against the grid size and, thus, the corresponding computer resource requirements for the computations at both wind tunnel and flight flow conditions. NOTE: Some details have been removed from selected plots and figures in compliance with the sensitive but unclassified (SBU) restrictions. However, the content still conveys the merits of the technical approach and the relevant results.

Aerodynamic characteristics↗

Photogrammetry of a Hypersonic Inflatable Aerodynamic Decelerator

In 2012, two large-scale models of a Hypersonic Inflatable Aerodynamic decelerator were tested in the National Full-Scale Aerodynamic Complex at NASA Ames Research Center. One of the objectives of this test was to measure model deflections under aerodynamic loading that approximated expected flight conditions. The measurements were acquired using stereo photogrammetry. Four pairs of stereo cameras were mounted inside the NFAC test section, each imaging a particular section of the HIAD. The views were then stitched together post-test to create a surface deformation profile. The data from the photogram- metry system will largely be used for comparisons to and refinement of Fluid Structure Interaction models. This paper describes how a commercial photogrammetry system was adapted to make the measurements and presents some preliminary results.

aerodynamic brakes↗

Unsteady Aerodynamic Force Sensing from Strain Data

A simple approach for computing unsteady aerodynamic forces from simulated measured strain data is proposed in this study. First, the deflection and slope of the structure are computed from the unsteady strain using the two-step approach. Velocities and accelerations of the structure are computed using the autoregressive moving average model, on-line parameter estimator, low-pass filter, and a least-squares curve fitting method together with analytical derivatives with respect to time. Finally, aerodynamic forces over the wing are computed using modal aerodynamic influence coefficient matrices, a rational function approximation, and a time-marching algorithm.

aerodynamic load sensing↗

Building Aerodynamic Databases for the SLS Design Process

NASA's new Space Launch System (SLS) will be the first rocket since the Saturn V (1967-1973) to carry astronauts beyond low earth orbit-and will carry 10% more payload than Saturn V and three times the payload of the space shuttle. The SLS configuration consists of a center core and two solid rocket boosters that separate from the core as their fuel is exhausted two minutes after lift-off. During these first two minutes of flight, the vehicle powers its way through strong shock waves as it accelerates past the speed of sound, then pushes beyond strong aerodynamic loads at the maximum dynamic pressure, and is ultimately enveloped by gaseous plumes from the booster-separation motors. The SLS program relies on computational fluid dynamic (CFD) simulations to provide much of the data needed to build aerodynamic databases describing the structural load distribution, surface pressures, and aerodynamic forces on the vehicle.

Aerodynamic↗

Aerodynamics and Aeroacoustic Sources of a Coaxial Rotor

Vehicles with coaxial, contra-rotating rotor systems (CACR) are being considered for a range of applications. Design parameters are identified that effect the fundamental aerodynamics and fluid dynamic features of a CACR in hover, vertical, and edgewise flight. Understanding the fluid dynamic features is a precursor to studying the aeroacoustics of a coaxial rotor. Rotor performance was computed initially using Navier-Stokes solver with prescribed blade section aerodynamic properties, the results validated against generic experimental test cases. Using a A 2D potential flow code and 2D OVERFLOW compressible-flow Navier-Stokes solver, the fluid dynamics of blade interactions was simplified and broken into a 2D blade crossing problem, with crossing locations and velocity fields from the rotor results to understand circulation, thickness, compressibility, shed vorticity, downwash, and viscosity effects. A calculation tool has been developed to identify time and location of blade overlap and BVI time location for CACR. Specific aerodynamic phenomena that occur for each noise source relevant to CACR are presented, along with computational tools to predict these occurrences.

Aeroacoustic↗