Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “waveguide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Phased array antenna matching: Simulation and optimization of a planar phased array of circular waveguide elements

A computerized simulation of a planar phased array of circular waveguide elements is reported using mutual coupling and wide angle impedance matching in phased arrays. Special emphasis is given to circular polarization. The aforementioned computer program has as variable inputs: frequency, polarization, grid geometry, element size, dielectric waveguide fill, dielectric plugs in the waveguide for impedance matching, and dielectric sheets covering the array surface for the purpose of wide angle impedance matching. Parameter combinations are found which produce reflection peaks interior to grating lobes, while dielectric cover sheets are successfully employed to extend the usable scan range of a phased array. The most exciting results came from the application of computer aided optimization techniques to the design of this type of array.

Dudgeon, J. E.↗

Finite-aperture waveguide-laser resonators.

A general theory of finite-aperture waveguide-laser resonators is developed which represents the external reflectors by matrices that couple linearly polarized waveguide modes having the same azimuthal symmetry. The theory allows the determination of resonator efficiency, resonator frequencies, and laser near- and far-field patterns. Computations of the coupling loss for the fundamental waveguide mode as a function of mirror curvature, separation, and aperture are in good agreement with recent infinite-aperture calculations in the limit of large apertures and indicate three low-loss configurations: (1) large radius of curvature mirrors close to the guide; (2) large radius of curvature mirrors centered at the guide entrance; and (3) generally smaller curvature mirrors separated by half their curvature from the guide entrance.

Degnan, J. J.↗

Waveguide CO2 laser gain: Dependence on gas kinetic and discharge properties

Using a simple rate equation approach the gas kinetic and discharge properties of waveguide CO2 lasers were examined. The dependence was calculated of the population inversion and laser small signal gain on gas pressure, gas mixture, pumping rate (discharge current), tube bore diameter, and wall temperature. At higher pressures the gain is optimized by using more helium rich mixtures and smaller bore diameters. The dependence of laser tunability on the gas kinetic properties and cavity losses was determined, it was found that for loss cavities the laser tunability may substantially exceed the molecular fullwidth at half maximum. The more helium rich gas mixtures give greater tunability when cavity losses are small and less tunability when cavity losses are large. The role of the various gases in the waveguide CO2 laser is the same as that in conventional devices, by contrast with conventional lasers, the waveguide laser transition is homogeneously broadened. The dependence of gain on gas pressure and other kinetic and discharge properties differs substantially from that predicted by scaling results from conventional low pressure lasers.

Cohen, S. C.↗

Fiber and diffused waveguide structures for distributed-feedback lasers

Optimum threshold conditions are derived for oscillations of transversely bounded distributed-feedback lasers in the cases of fiber and diffused waveguides, and it is shown that these structures are feasible with available active materials. The results of calculations show that a fiber laser has an optimum operating region which requires the least gain for self-sustained oscillation, while optimum operation occurs at the highest frequency possible in a diffused waveguide. It is noted that these gains can be achieved with dye in the case of a fiber waveguide and with dye or semiconductors in the case of a diffusion guide.

Elachi, C.↗

Linear charge coupled device detector array for imaging light propagating in an integrated thin-film optical waveguide

Device design, fabrication, and operation of a linear charge coupled device (CCD) detector array integrated with a thin film optical waveguide and applications of this structure to integrated optical signal processing and fiber optical communications were discussed. A two phase, overlapping-gate CCD is connected in parallel by means of a series of gates to an array of photodiodes. The photodiode provides an electrode free surface region so that a highly efficient waveguide detector coupling technique can be implemented. A thermally-oxidized layer of SiO2 forms an effective substrate for the optical waveguide.

Chen, C. L.↗

Temperature and pressure dependence of dichloro-difluoromethane (CF2C12) absorption coefficients for CO2 waveguide laser radiation

Measurements were performed to determine the pressure and temperature dependence of CFM-12 absorption coefficients for CO2 waveguide laser radiation. The absorption coefficients of CFM-12 for CO2 waveguide laser radiation were found to have no spectral structure within small spectral bandwidths around the CO2 waveguide laser lines in the CO2 spectral band for pressures above 20 torr. All of the absorption coefficients for the CO2 laser lines studied are independent of pressure above 100 torr, except for the P(36) laser CO2 spectral band. The absorption coefficients associated with the P(42) line in the same band showed the greatest change with temperature, and it also has the largest value of all the lines studied.

Harward, C. N.↗

Modal characteristics of crossed rectangular waveguides

An integral-eigenvalue problem is formulated for a crossed rectangular waveguide and solved numerically by applying the Ritz-Galerkin method. Theoretical formulas for determining cutoff frequencies and modal-field expressions are obtained for the specific case of a symmetrical rectangular waveguide, cutoff frequencies are calculated numerically, and the results are verified by comparison with available experimental data. The modal fields are expressed in terms of Fourier series for both TE and TM modes. It is found that the bandwidth can be increased to a maximum of 38% when the waveguide dimensions are properly selected and that the numerical results are in agreement with those computed by the method of partial regions. Some practical applications of the modal-field equations are briefly noted.

Lin, F.-L. C.↗

Evaluation of waveguide coating materials

Waveguide coating materials were tested at 8470 MHz for insertion loss. Samples of these coatings on waveguide pieces without flanges were tested in an environmental chamber to simulate the effects of high power microwave heating. Test results indicated that three types of coating materials are acceptable with regard to insertion loss. However, simulated microwave heating caused debonding of Metcot 7 and BD-991 coatings, resulting in peelings in the waveguide. The higher cost Chemglaze R104 does not exhibit this problem.

Chen, W. C. J.↗

Measurement and analysis of periodic coupling in silicon-clad planar waveguides

Computer modeling studies indicate that planar dielectric waveguides clad with silicon exhibit a damped periodic oscillation in their attenuation and phase characteristics. The effect is due to a periodic coupling between the lossy, guided modes in the silicon film and the TE0 mode of the dielectric waveguide. Experimental confirmation of the periodic coupling for a wavelength of 632.8 nm is presented. Propagation characteristics for a wavelength of 1150 nm were investigated for application in integrated optical modulators. Frequency filtering properties of silicon-clad waveguides are also examined and it is shown that the silicon thickness controls the filter response curve.

Mcwright, G. M.↗

A Leaky Waveguide Model for MHD Wave Driven Winds from Coronal Holes

Magnetohydrodynamic (MHD) waves, driven by the large scale convective motions of the photosphere are suggested as a possible source of additional acceleration for the stellar wind. Most of the turbulent power in a coronal hole is carried by MHD waves with periods of a few hundred seconds or longer. This is evident from direct observations of turbulence in the solar photosphere, as well as in situ observations of turbulence in the solar wind. But waves with periods this long have wavelengths which are typically as large as the transverse scale of the coronal hole flux tube itself. For these waves boundary effects are important and the coronal hole must be treated as a waveguide. The propagation of MHD waves using this waveguide approach is discussed. The simple model presented demonstrates that coronal holes can act as waveguides for MHD waves. For typical solar parameters the waves are compressible and can generate a wave tensile force which tends to cancel at least part of the wave pressure force. This effect tends to decrease the efficiency of MHD wave acceleration.

Davila, J. M.↗

Beam waveguides in the Deep Space Network

A beam waveguide is a mechanism for guiding electromagnetic radiation from one part of an antenna to another through a series of reflectors. Appropriate placement of reflectors on an antenna allows a beam to be guided around the elevation axis and/or below the alidade. The beam waveguide permits placement of all electronics in a room on the alidade below the elevation axis, or below the alidade; feed horn covers to be protected from the weather; and feed electronics to be in spacious rooms rather than in crowded cones, and always level rather than tipping with change in elevation angle. These factors can lead to lower costs in implementation such as Ka-band, better antenna performance at X-band, more efficient and stable performance of transmitters and receivers, and lower maintenance and operating costs. Studies are underway to determine methods for converting the major antennas of the Deep Space Network (DSN) to beam waveguide operations by 1995.

Clauss, R. C.↗

Electromagnetic scattering from a class of open-ended waveguide discontinuities

A relatively simple high frequency analysis of electromagnetic scattering from a class of open-ended waveguide discontinuites was developed. The waveguides are composed of perfectly-conducting sections in which the electromagnetic field can be written as the sum of waveguide modes. Junctions are formed at the open end and also within interior regions where different sections are joined. The reflection and transmission properties of each junction are described in terms of a scattering matrix which is determined by combining the modal ray picture with high frequency techniques such as the Geometrical Theory of Diffraction (GTD), the Equivalent Current Method (ECM), and modifications of the Physical Theory of Diffraction (PTD). A new set of equivalent circuits are employed in this ECM analysis which leads to a simple treatment of many types of junction discontinuities. Also, a new procedure is presented to improve the efficiency of the aperture integration at the open end which is required in the PTD procedure for finding the fields radiated from (or coupled to) the open end. Once the scattering matrices are determined, they are then combined using a self-consistent multiple scattering method to obtain the total scattered fields.

Altintas, A.↗

Cutoff wavenumbers and modes for annular-cross-section waveguide with eccentric inner conductor of small radius

Analytical expressions are derived for the cutoff wavenumbers and the corresponding modes in annular-cross-section waveguides having inner conductors of small radius. Waveguides with circular and rectangular outer boundary are considered. In the case of the circular eccentric annular waveguide, comparison is made between the values of cutoff wavenumbers computed from the expressions derived in this paper and data obtained by a more rigorous numerical technique.

Davidovitz, Marat↗

A selective modal scheme for the analysis of EM coupling into or radiation from large open-ended waveguides

A selective modal scheme is proposed to efficiently analyze the problem of high-frequency (HF) electromagnetic (EM) coupling/penetration into or radiation from open-ended waveguides. This scheme is based on the phenomenon that at sufficiently high frequencies, the modes which contribute most significantly to the fields coupled into the waveguide are those whose modal ray directions are most nearly parallel to the incident-wave direction. This concept is illustrated by calculating the EM radiation and backscattering from open-ended parallel-plate, rectangular, circular, and sectoral waveguide geometries. The calculations use the usual geometrical optics, aperture field, and Ufimtsev edge current techniques. Also included are some measured results which further verify the accuracy of the above computations.

Altintas, Ayhan↗

Fabrication Of Fiber-Optic Waveguide Coupler

Technique for making four-port, single-mode fiber-optic waveguide couplers requires no critically-precise fabrication operations or open-loop processes. Waveguide couplers analogous to beam-splitter prisms. Essential in many applications that require coherent separation or combination of two waves; for example, for interferometric purposes. Components of optical waveguide coupler held by paraffin on microscope slide while remaining cladding of two optical fibers fused together by arc welding.

Goss, Willis↗

Improved Coplanar Waveguides

Three new types of coplanar waveguide transmission lines proposed: suspended, striplinelike suspended, and inverted. Numerical analyses of propagation of electromagnetic fields of new and of more-conventional plain and conductor-backed coplanar waveguides showed new waveguides offered several advantages over conventional ones. Configurations promise lower attenuation and reduce effects of manufacturing errors.

Simons, Rainee N.↗

Ray analysis of modal reflection for three-dimensional open-ended waveguides

An efficient high-frequency ray analysis, which combines the geometrical theory of diffraction (GTD) with the equivalent current method, is used for evaluating modal reflection at the open ends of three-dimensional waveguides. After reviewing a method used for the two-dimensional case and introducing some extensions necessary for evaluating modal reflection of open-ended three-dimensional waveguides, the modal reflection coefficients are then given for open-ended circular and rectangular waveguides. Numerical results calculated using these expressions agree favorably with those obtained by a different analytical technique and by experiment.

Chuang, C. W.↗

Modal, ray, and beam techniques for analyzing the EM scattering by open-ended waveguide cavities

The problem of high-frequency electromagnetic (EM) scattering by open-ended waveguide cavities with an interior termination is analyzed via three different approaches. When cavities can be adequately modeled by joining together piecewise separable waveguide sections, a hybrid combination of asymptotic high-frequency and modal techniques is employed. In the case of more arbitrarily shaped waveguide cavities for which modes cannot even be defined in the conventional sense, the geometrical optics ray approach proves to be highly useful. However, at sufficiently high frequencies, both of these approaches tend to become inefficient. Hence, a paraxial Gaussian batch technique, which retains much of the simplicity of the ray approximation but is potentially more efficient, is investigated. Typical numerical results based on the different approaches are discussed.

Pathak, Prabhakar H.↗