Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “voltage stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

On forced RF generation of CW magnetrons for SRF accelerators

CW magnetrons, initially developed for industrial RF heaters, were suggested to power RF cavities of superconducting accelerators due to their higher efficiency and lower cost of RF power per Watt than used traditionally klystrons, IOTs or solid-state amplifiers. RF amplifiers driven by a master oscillator serve as coherent RF sources. CW magnetrons are regenerative RF generators with a huge regenerative gain to start up reliably with self-excitation even if the tube is powered by a DC power supply. This causes regenerative instability with a large noise when a magnetron operates with the anode voltage above the threshold of self-excitation. Traditionally for stabilization of magnetrons is used injection locking by a signal PLock ≤ -20 dB or less then of the magnetron power PMag. Then the magnetron generates the injection locked oscillations and generates noise. This may preclude use of standard CW magnetrons in some SRF accelerators. We developed briefly described below a mode for forced coherent RF generation of CW magnetrons when the magnetron startup is provided by the injected forcing signal and the regenerative noise is suppressed. The mode is most suitable for powering high Q-factor SRF cavities.

Kazakevich, G.↗
DOE OSTI2020

Membrane-Free Zn/MnO 2 Flow Battery for Large-Scale Energy Storage

The traditional Zn/MnO 2 battery has attracted great interest due to its low cost, high safety, high output voltage, and environmental friendliness. However, it remains a big challenge to achieve long-term stability, mainly owing to the poor reversibility of the cathode reaction. Different from previous studies where the cathode redox reaction of MnO 2 /MnOOH is in solid state with limited reversibility, in this work a new aqueous rechargeable Zn/MnO 2 flow battery is constructed with dissolution–precipitation reactions in both cathodes (Mn 2+ /MnO 2 ) and anodes (Zn 2+ /Zn), which allow mixing of anolyte and catholyte into only one electrolyte and remove the requirement for an ion selective membrane for cost reduction. Impressively, this new battery exhibits a high discharge voltage of ≈1.78 V, good rate capability (10C discharge), and excellent cycling stability (1000 cycles without decay) at the areal capacity ranging from 0.5 to 2 mAh cm -2 . More importantly, this battery can be readily enlarged to a bench scale flow cell of 1.2 Ah with good capacity retention of 89.7% at the 500th cycle, displaying great potential for large-scale energy storage.

25 ENERGY STORAGE↗
DOE OSTI2025

Radiation Response of Ga 2 O 3 MOSFETs Probed via Focused Particle Beams

Gallium Oxide (Ga 2 O 3 ), particularly in its β-phase, is attracting lots of interest for high-power and high-voltage electronics due to its wide bandgap, high breakdown field, and thermal stability. This study investigates the radiation response of Ga 2 O 3 Metal-Oxide-Semiconductor Field-Effect Transistors (MOSFETs) under Total Ionizing Dose (TID) and Displacement Damage (DD) conditions, which are critical for applications in radiation environments. Utilizing a dual-beam Focused Ion Beam and Scanning Electron Microscope setup, microscale analysis of radiation effects on individual devices is performed. The findings reveal distinct behaviors under TID and DD + TID conditions, with TID leading to threshold voltage shifts due to trapped charges, while DD results in decreased drive current attributed to increased carrier scattering from lattice defects. Notably, it is demonstrated that the TID effect can be mitigated through dynamic threshold voltage adjustments and that the predicted TID from ions calculated by Monte Carlo simulations overestimates actual TID due to unaccounted charge yield effects. In conclusion, this research enhances the understanding of Ga2O3 MOSFETs' performance in harsh radiation environments, providing insights for the design of robust electronic devices for space and nuclear applications.

MOSFET↗
DOE OSTI2024

Photo-Crosslinkable Naphthalene Diimide Polymer for Solution-Processed n – i – p Perovskite Solar Cells

We copolymerize a norbornene monomer bearing a pendant naphthalene diimide with a norbornene bearing a cinnamate pendant moiety to synthesize a crosslinkable electron-transporting polymer and study its use in solution-processed n–i–p perovskite solar cells. The crosslinked material exhibits over 90% transparency in the visible region and higher thermal stability (>300 °C) and lower surface energy than the corresponding homopolymer of the naphthalene diimide functionalized norbornene. Coating an ITO surface with the photo-crosslinked copolymer yields a slightly lower work function than homopolymer-coated ITO. We show that the morphologies of the perovskite films deposited on both polymers are similar (~300 nm features) based upon scanning electron microscopy. Our solar-cell device results show that the crosslinked naphthalene diimide polymer gives a higher open-circuit voltage (1.08 vs 1.05 V), fill factor (average 64.43 vs 58.77%), and stabilized power conversion efficiency (12.28 vs 10.33%) compared to its non-crosslinked homopolymer counterpart, as well as reduced hysteresis. As a result, we attribute the improved performance to decreased work function, reduced nonradiative recombination, and higher shunt resistance.

14 SOLAR ENERGY↗
DOE OSTI2024

Stabilizing high-Ni cathodes with gradient surface Ti-enrichment

High-Ni cathodes are being intensely pursued worldwide for electric vehicles and other energy-dense applications due to their high capacity and low cost. However, structural instabilities during electrochemical cycling and when subjected to thermal treatment have been the major issues hindering their practical deployment. We here report a rational design of coating-integrated-into-synthesis protocol for fabricating surface Ti-enriched LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811#Ti) material. The coating to intermediates is crucial to obtain high structural ordering, both in the bulk and surface of high-Ni cathodes, and the Ti substitute has a unique tri-valence (Ti 3+ ) in a gradient surface distribution. Further, the simulations of projected density of states in the atomistic understanding further certify significantly enhanced stability of lattice oxygen for the NMC811 through such a Ti 3+ -based structure reinforcement. Consequently, the NMC811#Ti cathode delivers a high capacity up to 200mAhg -1 at 0.1 C, along with superior stabilities during air-storage and thermal treatment (up to 297°C at the fully charged state under differential scanning calorimetric measurements). The corresponding NMC811#Ti||graphite full cell exhibits a desired 83.6% capacity retention after 1000 cycles at 0.5 C in a voltage range of 2.8–4.3V. This work demonstrates a delicate surface reinforcement to stabilize high-Ni cathodes for long-life and safe lithium-ion batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Correlation of Band Bending and Ionic Losses in 1.68 eV Wide Band Gap Perovskite Solar Cells

Abstract Perovskite solar cells (PSCs) are promising for high‐efficiency tandem applications, but their long‐term stability, particularly due to ion migration, remains a challenge. Despite progress in stabilizing PSCs, they still fall short compared to mature technologies like silicon. This study explores how different piperazinium salt treatments using iodide, chloride, tosylate, and bistriflimide anions affect the energetics, carrier dynamics, and stability of 1.68 eV bandgap PSCs. Chloride‐based treatments achieved the highest power conversion efficiency (21.5%) and open‐circuit voltage (1.28 V), correlating with stronger band bending and n‐type character at the surface. At the same time, they showed reduced long‐term stability due to increased ionic losses. Tosylate‐treated devices offered the best balance, retaining 96.4% efficiency after 1000 h (ISOS‐LC‐1I). These findings suggest that targeted surface treatments can enhance both efficiency and stability in PSCs.

14 SOLAR ENERGY↗
DOE OSTI2022

Thoughts and Hypotheses on the Metrics and Needs for the Stability of Highly Inverter-Based Island Systems

As levels of wind, photovoltaics (PVs), and battery energy storage on power systems rise, it is useful to be able to quickly compare how much generation (instantaneous power and annual energy) comes from these inverter-based resources (IBRs). A commonly used metric is the percentage of inverter-based generation (% IBR) in a dispatch scenario (as a percentage of the total generation or total load), which can be useful for estimating when certain operational challenges arise (high rates of change of frequency, underdamped control interactions, low system strength, low fault current availability, and so on). Another similar and commonly used metric pioneered on the relatively large island of Ireland, system nonsynchronous penetration (SNSP), is similar to the % IBR and is subject to similar limitations. SNSP has the advantage of handling high-voltage dc in a defined way.

fault currents↗
DOE OSTI2020

Modeling and Harmonic Stability of MMC-HVDC With Passive Circulating Current Filters

A modular multilevel converter (MMC) is an emerging converter technology widely used in wind power applications using high-voltage direct current (HVDC) transmission, and it has been largely investigated in medium-voltage solar harvesting as well as electric motor drives. Different from studies dealing with active circulating current control loops, this paper focuses on impedance modeling and harmonic stability studies for MMCs with passive circulating current filters (PCCFs). A power stage circuit including a PCCF is transformed and remodeled to obtain small-signal formulations. This transformation leads to additional high-order matrix computing complexity due to the added impedance subnetwork matrix from the PCCF as well as relevant crossed-frequency impacts. To simplify the computational burden, the proposed model aims to solve one arm equation instead of all six MMC arm equations. To achieve this result, additional challenges occur when the MMC is connected to a renewable energy source instead of the grid voltage, where low-level zero-sequence components might exist in the neutral point of three phases, especially in the case of no integrated advanced modular voltage balancing control, which prevents computational simplification. To overcome this challenge, further impedance matrix adjustments are conducted in this paper to theoretically suppress the impact of zero-sequence harmonics when obtaining small-signal impedance, taking into account the frequency coupling effect. Finally, simulations are carried out to validate the developed impedance model under different operating scenarios. Harmonic stability case studies of MMCs with PCCFs connected to renewable energy current sources are also presented, where frequency-domain stability analyses based on Bode diagrams are compared to time-domain simulation waveforms and FFTs, which validate the effectiveness of the proposed impedance model.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2023

Inhibit the strain accumulation for 5V spinel cathode by mitigating the phase separation during high voltage stage

LiNi 0.5 Mn 1.5 O 4 (LNMO) spinel cathode is a potential cathode material for high-power, low-cost lithium-ion batteries (LIBs) due to its low raw material cost, high operating voltage and efficient lithium-ion transport channel. However, LNMO suffers from structural stability due to the two-phase-transformation during charge/discharge process, leading to poor cycling performance. Here, to address the issues, we have constructed a homogeneous aggregated LNMO cathode with a multifaceted primary particle, namely the LNMO with single-crystal secondary particles (SSP LNMO). Ex situ and in situ characterizations including the synchrotron X-ray diffraction, the neutron diffraction and full pouch cell validated that the SSP LNMO exhibit a single solid-solution reactions with a restrained lattice evolution during the delithiation/lithiation process. This is in contrast to the normal LNMO cathode, which demonstrates a significant two-phase transition from spinel Li 1-x Ni 0.5 Mn 1.5 O 4 to rock-salt MnO 2 at high voltage. Therefore, the SSP LNMO has greatly improved cycle life compared to the normal LNMO cathode. Overall, this study demonstrates the possibility of constructing LNMO based on primary-grain morphology modulation to improve the intrinsic stability of LIBs.

25 ENERGY STORAGE↗
DOE OSTI2021

Sequence Impedance Measurement of Utility-Scale Wind Turbines and Inverters – Reference Frame, Frequency Coupling, and MIMO/SISO Forms

Sequence impedance responses with or without considering frequency coupling in both MIMO and SISO forms are increasingly used for the stability analysis of three-phase power electronic systems; however, many aspects of sequence impedance measurement are not fully explored. It is not clear if the sequence impedance has a reference frame similar to the dq impedance. If so, the role of the grid voltage angle estimation in aligning the sequence impedance reference frame has not been discussed. Additionally, existing methods for measuring the sequence impedance with frequency coupling are complicated, are not feasible for large wind turbines and inverters, and provide the sequence impedance responses in only either MIMO or SISO form. This paper presents a sequence impedance measurement method that considers the frequency coupling, performs reference frame alignment, demonstrates the impact of the grid voltage angle estimation, and obtains the sequence impedance response in both MIMO and SISO forms. This paper demonstrates the proposed method and practical problems associated with the sequence impedance measurement of utility-scale wind turbines and inverters on a 1.9-MW Type III wind turbine and a 2.2-MVA inverter using an impedance measurement system built around a 7-MW/13.8-kV grid simulator and a 5-MW dynamometer.

17 WIND ENERGY↗
DOE OSTI2025

Precise Synthesis of 4.75 V-Tolerant LiCoO 2 with Homogeneous Delithiation and Reduced Internal Strain

The rapid advancements in 3C electronic devices necessitate an increase in the charge cutoff voltage of LiCoO 2 to unlock a higher energy density that surpasses the currently available levels. However, the structural devastation and electrochemical decay of LiCoO 2 are significantly exacerbated, particularly at ≥4.5 V, due to the stress concentration caused by more severe lattice expansion and shrinkage, coupled with heterogeneous Li + intercalation/deintercalation reactions. Herein, employing the molten-salt synthesis technique, we propose a universal morphology-shaping strategy to attain bulk reaction homogeneity and reduce internal strains, even at extremely high charge voltages. The newly designed flattened polygon prismlike LiCoO 2 (P-LCO) particle, featuring a regular symmetrical arrangement along the c-axis, demonstrates a more homogeneous Li + extraction/insertion reaction, which results in a restrained transformation to detrimental O1 phase and reduced variation in lattice volume throughout the (de)lithiation processes. This benefits the mitigation of the local stress accumulation misfit dislocations and particle cracking, ultimately maintaining the mechanical stability of the cathode. Consequently, P-LCO is capable of breaking the voltage ceiling and exhibits exceptional long-term cycling capability at an ultrahigh voltage of 4.75 V. In conclusion, this work offers a brand-new perspective for the rational design of cathode morphology to address capacity deterioration caused by inhomogeneous delithiation and internal strain, thus inspiring the development of high-energy-density cathodes with improved durability.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Digital Twin-Enabled Adaptive Control for Hydroelectric Systems: Turbine Governor and Voltage Regulation

This paper presents a comprehensive digital twin (DT) framework for hydroelectric systems that enables adaptive control of turbine governors and excitation systems without requiring detailed manufacturer specifications. The proposed framework integrates neural network-based system identification with stabilizing adaptive control laws for the installed turbine controller and middle-branch adaptive tuning for the installed voltage regulator. Using real operational data from Unit C-8 at Rocky Reach Dam (1,349 MW capacity), highfidelity neural network models are developed to capture turbine and generator dynamics without requiring detailed manufacturer specifications. The DT enables safe controller synthesis and validation in simulation before deployment. For turbine control, the proposed method achieves a 79.9% mean square error (MSE) reduction compared with that of an optimal controller. For voltage regulation, the adaptive excitation controller achieves approximately 42.6% MSE reduction while preserving installed protection logic. The results demonstrate that DT technology provides a practical pathway for modernizing hydropower control systems with minimal operational disruption.

Gui, Yonghao [ORNL] (ORCID:0000000250435534)↗
DOE OSTI2020

Beyond Strain: Controlling the Surface Chemistry of CsPbI 3 Nanocrystal Films for Improved Stability against Ambient Reactive Oxygen Species

Colloidal halide perovskite nanocrystals (NCs) have the possibility of easy scale-up due to their batch synthesis and have demonstrated excellent optoelectronic properties. In particular, perovskite NCs have remarkably high photoluminescence quantum yields in solution and as thin films and impressive open circuit voltages in photovoltaic devices. Despite these promising results, little work has been done to understand the stability of CsPbI 3 NCs for optoelectronic device applications. It has been previously shown that the ligands impart tensile surface strain, which stabilizes the black three-dimensional (3D) perovskite phase against phase degradation, making CsPbI 3 NCs some of the most structurally robust inorganic halide perovskites to date. However, understanding exactly how CsPbI 3 NCs degrade under ambient conditions is critical. Additionally, we demonstrate that the degradation mechanism of NCs is unique from, and 2 orders of magnitude slower than, their polycrystalline thin-film counterparts. Under specific conditions, CsPbI 3 NC films show a compositional instability instead of the phase instability seen in large grain CsPbI 3 . This is mediated through reactions with superoxide and other reactive oxygen species, which are initiated from surface defect states, O 2 and light. We then use this mechanistic insight to identify multiple strategies to prolong the lifetimes of CsPbI 3 NC films, by going beyond surface strain to mitigate key surface chemistries. We demonstrate that (1) minimizing the number of surface defects (2) using an alkylammonium bromide ligand surface treatment and (3) encapsulation with an oxygen scavenging layer all increase NC film lifetimes by inhibiting various steps in the photo-oxidation degradation reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Device Performance of Emerging Photovoltaic Materials (Version 3)

Abstract Following the 2nd release of the “Emerging PV reports,” the best achievements in the performance of emerging photovoltaic devices in diverse emerging photovoltaic research subjects are summarized, as reported in peer‐reviewed articles in academic journals since August 2021. Updated graphs, tables, and analyses are provided with several performance parameters, e.g., power conversion efficiency, open‐circuit voltage, short‐circuit current density, fill factor, light utilization efficiency, and stability test energy yield. These parameters are presented as a function of the photovoltaic bandgap energy and the average visible transmittance for each technology and application, and are put into perspective using, e.g., the detailed balance efficiency limit. The 3rd installment of the “Emerging PV reports” extends the scope toward triple junction solar cells.

14 SOLAR ENERGY↗
DOE OSTI2021

Large area vertical Ga 2 O 3 Schottky diodes for X-ray detection

In this work, the Schottky barrier diodes were fabricated from a bulk Sn-doped (001) n-type Ga 2 O 3 substrate with a Si-doped epitaxial layer grown by hydride vapor phase epitaxy (HVPE), which demonstrate a good response to X-rays. Circular metal contacts with diameters ranging from 50 to 1500 um and square metal contacts ranging from 100 X 100 to 1600 X 1600 um 2 were deposited on the wafer. The devices were characterized for their electrical performance including forward current–voltage (FIV), reverse current–voltage (RIV), and capacitance-voltage (CV) measurements. The best device showed a breakdown voltage of –804 V and the devices tested had an average ideality of 1.12. The devices exhibited a clear response to X-rays even at zero bias with an experimentally observed response time 1.03 s and a linear response of detector signal to the X-ray dose rate. The experimentally observed device response time improved to 0.25 s when bias voltage is applied. The device also survived a long-term stability test of over 2 h under a constant X-ray irradiation. The sensitivity and the lower limit of detection for X-ray by Ga2O3 epitaxial Schottky detectors were discussed and determined as 43.5 C/mGy cm –2 at –200 V and 8.31 nGy Air /s, respectively.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Transition Metal Dissolution Mechanisms and Impacts on Electronic Conductivity in Composite LiNi 0.5 Mn 1.5 O 4 Cathode Films

The high-voltage LiNi 0.5 Mn 1.5 O 4 (LNMO) spinel cathode material offers high energy density storage capabilities without the use of costly Co that is prevalent in other Li-ion battery chemistries (e.g., LiNi x Mn y Co z O 2 (NMC)). Unfortunately, LNMO-containing batteries suffer from poor cycling performance because of the intrinsically coupled processes of electrolyte oxidation and transition metal dissolution that occurs at high voltage. In this work, we use operando electron paramagnetic resonance (EPR) and nuclear magnetic resonance (NMR) spectroscopies to demonstrate that transition metal dissolution in LNMO is tightly coupled to HF formation (and thus, electrolyte oxidation reactions as detected with operando and in situ solution NMR), indicative of an acid-driven disproportionation reaction that occurs during delithiation (i.e., battery charging). Leveraging the temporal resolution (s-min) of magnetic resonance, we find that the LNMO particles accelerate the rate of LiPF 6 decomposition and subsequent Mn 2+ dissolution, possibly due to the acidic nature of terminal Mn-OH groups. X-ray photoemission electron microscopy (XPEEM) provides surface-sensitive and localized X-ray absorption spectroscopy (XAS) measurements, in addition to X-ray photoelectron spectroscopy (XPS), that indicate disproportionation is enabled by surface reconstruction upon charging, which leads to surface Mn 3+ sites on the LNMO particle surface that can disproportionate into Mn 2+ (dissolved) and Mn 4+ (s) . During discharge of the battery, we observe high quantities of metal fluorides (in particular, MnF 2 ) in the cathode electrolyte interphase (CEI) on LNMO as well as the conductive carbon additives in the composite. Electronic conductivity measurements indicate that the MnF 2 decreases film conductivity by threefold compared to LiF, suggesting that this CEI component may impede both the ionic and electronic properties of the cathode. Ultimately, to prevent transition metal dissolution and the associated side reactions in spinel-type cathodes (particularly those that operate at high voltages like LNMO), the use of electrolytes that offer improved anodic stability and prevent acid byproducts will likely be necessary.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Enabling Grid-Forming Control with Fault Ride-Through in Unbalanced Distribution Networks

Distribution networks are often unbalanced, causing oscillatory responses in inverter control designed for balanced conditions. Here, to address this problem, this paper proposes a novel time-domain transformation appropriate for inverter control and enables the decomposition of three-phase unbalanced signals into constant positive and negative components. Relations useful for calculating unbalanced active and reactive power are derived from first principle, providing insight into vector products of unbalanced three-phase signals. Furthermore, a grid-forming control effective under unbalanced conditions is developed, which delivers superior performance while meeting UNIFI1 specifications for grid-forming control under unbalanced conditions. specifications applicable to category 4 inverter-based resource, like setting and regulating frequency/voltage, providing voltage support, sharing active power, injecting negative sequence current, and riding through faults. A current limiter is proposed for safe fault ride-through and integrates with the grid-forming control featuring frequency/voltage droop controllers and current and voltage control loops. The transformation of interconnected inverters is formulated and stability of the proposed control analyzed to support robust parameter selections. The effectiveness of the proposed transformation and grid-forming control is demonstrated through analytical results and real-time simulation of a IEEE 123 distribution network on the Real-Time Digital Simulator. Comparison with existing methods shows that the proposed strategy satisfies the UNIFI specifications with a much better performance.

24 - POWER TRANSMISSION AND DISTRIBUTION↗