Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “variable geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Validation of MODIS 3 km Land Aerosol Optical Depth from NASA's EOS Terra and Aqua Missions

In addition to the standard resolution product (10km), the MODerate resolution Imaging Spectroradiometer (MODIS) Collection 6 (C006) data release included a higher resolution (3km). Other than accommodations for the two different resolutions, the 10 and 3km Dark Target (DT) algorithms are basically the same. In this study, we perform global validation of the higher-resolution aerosol optical depth (AOD) over global land by comparing against AErosol RObotic NETwork (AERONET) measurements. The MODIS-AERONET collocated data sets consist of 161410 high-confidence AOD pairs from 2000 to 2015 for Terra MODIS and 2003 to 2015 for Aqua MODIS. We find that 62.5 and 68.4% of AODs retrieved from Terra MODIS and Aqua MODIS, respectively, fall within previously published expected error bounds of +/-(0.05+0.2 × AOD), with a high correlation (R = 0.87). The scatter is not random, but exhibits a mean positive bias of ∼ 0.06 for Terra and ∼ 0.03 for Aqua. These biases for the 3km product are approximately 0.03 larger than the biases found in similar validations of the 10km product. The validation results for the 3km product did not have a relationship to aerosol loading (i.e., true AOD), but did exhibit dependence on quality flags, region, viewing geometry, and aerosol spatial variability. Time series of global MODIS-AERONET differences show that validation is not static, but has changed over the course of both sensors' lifetimes, with Terra MODIS showing more change over time. The likely cause of the change of validation over time is sensor degradation, but changes in the distribution of AERONET stations and differences in the global aerosol system itself could be contributing to the temporal variability of validation.

Gupta, Pawan↗
NASA NTRS2018

Exploring the Effects of Installation Geometry in High-Lift Propeller Systems

A high-lift propeller system is a distributed electric propulsion technology which dedicates an array of wing-mounted tractor propellers to actively augment wing lift during takeoff and landing. This paper describes the results of a wind tunnel experiment dedicated to investigating the effects of high-lift propeller installation geometry on lift generation. Variables investigated include propeller height, offset, and inclination. Results show that propeller height is the most critical variable and that the height for maximum lift depends highly on the angle of attack and flap deflection. In addition, a relationship between optimal propeller height and the wing’s unblown lift coefficient is discovered.

Fei, Xiaofan↗
NASA NTRSDate not supplied

Effective Emissivity of Nonisothermal Isogrid for Spacecraft Radiator Applications

Accurate knowledge of the optical properties of spacecraft components, especially external components, is critical for proper spacecraft thermal design. The effective emissivity of isogrid (an array of equilateral triangular cavities) is not well understood, which poses a challenge for spacecraft thermal management. In this thesis the effective emissivity of isogrid with a prescribed base temperature and nonisothermal walls is examined. The temperature profile of the cavity’s walls and the overall effective emissivity of the cavity are found using Thermal Desktop with Monte Carlo ray tracing. The effective emissivity’s dependence on the wall height, wall thickness, wall resistance, and surface emissivity are examined. The existence of a critical wall height, and the contributing factors to this critical height, are discussed. Comparisons between isogrid and cavities with different base geometries are made. A variable emissivity isogrid spacecraft radiator concept employing the cavity effect is proposed, and mechanisms for achieving this are discussed.

Seth Abramczyk↗
NASA NTRS2022

Look-up Table Approach for Uncertainty Determination for Operational Vicarious Calibration of Earth Imaging Sensors

Understanding the uncertainty of a vicarious calibration is essential for any application to Earth imaging sensors. The Radiometric Calibration Network provides SI-traceable spectral top-of-atmosphere (TOA) reflectance from a network of ground sites and uses a look-up table (LUT) approach for uncertainty determination. The uncertainty LUT was derived using Monte Carlo techniques applied to the relevant solar geometry, surface, and atmospheric variables. While surface reflectance is typically the dominant uncertainty source, atmospheric contributions do play an important role, depending upon the exact scenario and conditions. This approach allows knowledge of TOA reflectance uncertainty to within 0.5%.

Brian N. Wenny↗
NASA NTRS1982

A Computer Code for Swirling Turbulent Axisymmetric Recirculating Flows in Practical Isothermal Combustor Geometries

A primitive pressure-velocity variable finite difference computer code was developed to predict swirling recirculating inert turbulent flows in axisymmetric combustors in general, and for application to a specific idealized combustion chamber with sudden or gradual expansion. The technique involves a staggered grid system for axial and radial velocities, a line relaxation procedure for efficient solution of the equations, a two-equation k-epsilon turbulence model, a stairstep boundary representation of the expansion flow, and realistic accommodation of swirl effects. A user's manual, dealing with the computational problem, showing how the mathematical basis and computational scheme may be translated into a computer program is presented. A flow chart, FORTRAN IV listing, notes about various subroutines and a user's guide are supplied as an aid to prospective users of the code.

Lilley, D. G.↗
NASA NTRSDate not supplied

A Moving Discontinuous Galerkin Method with Interface Condition Enforcement for Reacting Hypersonic Flows

The necessity of enforcing conservation in computational elements or cells (element conservation) for discontinuous solutions is well understood and respected for solving conservation laws in computational fluid dynamics (CFD). In contrast, interface conservation, where the conservation across cell interfaces is enforced, is long ignored, and yet is also ruled and required by the underlying physics just like element conservation. Violation of the interface conservation across discontinuities is the root cause why an exact discontinuous solution can never be achieved in shock capturing methods. The interface conservation is examined and explored in this talk. Moving discontinuous Galerkin (MDG) finite element method with interface conservation enforcement (MDG-ICE) [1],[2] are then presented for solving compressible flow problems with discontinuities based on the observation that the interface conservation can only be satisfied, only when mesh interfaces are aligned with discontinuities. In the MDG-ICE formulation, both conservative quantities and grid geometry are considered as independent variables. A space-time DG formulation is used to solve the multi-material compressible Euler equations in the standard discontinuous solution space and the discrete grid geometry is solved using a variational formulation in a continuous space. A self-adaptive Levenberg-Marquardt method is utilized to solve the resulting over-determined system of nonlinear equations arising from the MDG-ICE formulation. A number of numerical experiments for a variety of flow problems are conducted to assess the accuracy and performance of the MDG-ICE method. Numerical results obtained indicate that the MDG-ICE method is able to deliver the designed order of both h- and p-convergence even for discontinuous solutions, and detect all types of interfaces, via interface condition enforcement and satisfy, via grid movement, the compressible Euler equations and the associated interface condition.

Discontinuous Galekin↗
NASA NTRS1980

On the nonlinear deformation geometry of Euler-Bernoulli beams

Nonlinear expressions are developed to relate the orientation of the deformed beam cross section, torsion, local components of bending curvature, angular velocity, and virtual rotation to deformation variables. The deformed beam kinematic quantities are proven to be equivalent to those derived from various rotation sequences by identifying appropriate changes of variable based on fundamental uniqueness properties of the deformed beam geometry. The torsion variable used is shown to be mathematically analogous to an axial deflection variable commonly used in the literature. Rigorous applicability of Hamilton's principle to systems described by a class of quasi-coordinates that includes these variables is formally established.

Hodges, D. H.↗
NASA NTRS2008

Advanced Stirling Convertor Heater Head Durability and Reliability Quantification

The National Aeronautics and Space Administration (NASA) has identified the high efficiency Advanced Stirling Radioisotope Generator (ASRG) as a candidate power source for long duration Science missions, such as lunar applications, Mars rovers, and deep space missions, that require reliable design lifetimes of up to 17 years. Resistance to creep deformation of the MarM-247 heater head (HH), a structurally critical component of the ASRG Advanced Stirling Convertor (ASC), under high temperatures (up to 850 C) is a key design driver for durability. Inherent uncertainties in the creep behavior of the thin-walled HH and the variations in the wall thickness, control temperature, and working gas pressure need to be accounted for in the life and reliability prediction. Due to the availability of very limited test data, assuring life and reliability of the HH is a challenging task. The NASA Glenn Research Center (GRC) has adopted an integrated approach combining available uniaxial MarM-247 material behavior testing, HH benchmark testing and advanced analysis in order to demonstrate the integrity, life and reliability of the HH under expected mission conditions. The proposed paper describes analytical aspects of the deterministic and probabilistic approaches and results. The deterministic approach involves development of the creep constitutive model for the MarM-247 (akin to the Oak Ridge National Laboratory master curve model used previously for Inconel 718 (Special Metals Corporation)) and nonlinear finite element analysis to predict the mean life. The probabilistic approach includes evaluation of the effect of design variable uncertainties in material creep behavior, geometry and operating conditions on life and reliability for the expected life. The sensitivity of the uncertainties in the design variables on the HH reliability is also quantified, and guidelines to improve reliability are discussed.

Krause, David L.↗
NASA NTRS1999

Engineering Overview of a Multidisciplinary HSCT Design Framework Using Medium-Fidelity Analysis Codes

An objective of the HPCC Program at NASA Langley has been to promote the use of advanced computing techniques to more rapidly solve the problem of multidisciplinary optimization of a supersonic transport configuration. As a result, a software system has been designed and is being implemented to integrate a set of existing discipline analysis codes, some of them CPU-intensive, into a distributed computational framework for the design of a High Speed Civil Transport (HSCT) configuration. The proposed paper will describe the engineering aspects of integrating these analysis codes and additional interface codes into an automated design system. The objective of the design problem is to optimize the aircraft weight for given mission conditions, range, and payload requirements, subject to aerodynamic, structural, and performance constraints. The design variables include both thicknesses of structural elements and geometric parameters that define the external aircraft shape. An optimization model has been adopted that uses the multidisciplinary analysis results and the derivatives of the solution with respect to the design variables to formulate a linearized model that provides input to the CONMIN optimization code, which outputs new values for the design variables. The analysis process begins by deriving the updated geometries and grids from the baseline geometries and grids using the new values for the design variables. This free-form deformation approach provides internal FEM (finite element method) grids that are consistent with aerodynamic surface grids. The next step involves using the derived FEM and section properties in a weights process to calculate detailed weights and the center of gravity location for specified flight conditions. The weights process computes the as-built weight, weight distribution, and weight sensitivities for given aircraft configurations at various mass cases. Currently, two mass cases are considered: cruise and gross take-off weight (GTOW). Weights information is obtained from correlations of data from three sources: 1) as-built initial structural and non-structural weights from an existing database, 2) theoretical FEM structural weights and sensitivities from Genesis, and 3) empirical as-built weight increments, non-structural weights, and weight sensitivities from FLOPS. For the aeroelastic analysis, a variable-fidelity aerodynamic analysis has been adopted. This approach uses infrequent CPU-intensive non-linear CFD to calculate a non-linear correction relative to a linear aero calculation for the same aerodynamic surface at an angle of attack that results in the same configuration lift. For efficiency, this nonlinear correction is applied after each subsequent linear aero solution during the iterations between the aerodynamic and structural analyses. Convergence is achieved when the vehicle shape being used for the aerodynamic calculations is consistent with the structural deformations caused by the aerodynamic loads. To make the structural analyses more efficient, a linearized structural deformation model has been adopted, in which a single stiffness matrix can be used to solve for the deformations under all the load conditions. Using the converged aerodynamic loads, a final set of structural analyses are performed to determine the stress distributions and the buckling conditions for constraint calculation. Performance constraints are obtained by running FLOPS using drag polars that are computed using results from non-linear corrections to the linear aero code plus several codes to provide drag increments due to skin friction, wave drag, and other miscellaneous drag contributions. The status of the integration effort will be presented in the proposed paper, and results will be provided that illustrate the degree of accuracy in the linearizations that have been employed.

Weston, R. P.↗
NASA NTRS1993

Optimal design of composite hip implants using NASA technology

Using an adaptation of NASA software, we have investigated the use of numerical optimization techniques for the shape and material optimization of fiber composite hip implants. The original NASA inhouse codes, were originally developed for the optimization of aerospace structures. The adapted code, which was called OPORIM, couples numerical optimization algorithms with finite element analysis and composite laminate theory to perform design optimization using both shape and material design variables. The external and internal geometry of the implant and the surrounding bone is described with quintic spline curves. This geometric representation is then used to create an equivalent 2-D finite element model of the structure. Using laminate theory and the 3-D geometric information, equivalent stiffnesses are generated for each element of the 2-D finite element model, so that the 3-D stiffness of the structure can be approximated. The geometric information to construct the model of the femur was obtained from a CT scan. A variety of test cases were examined, incorporating several implant constructions and design variable sets. Typically the code was able to produce optimized shape and/or material parameters which substantially reduced stress concentrations in the bone adjacent of the implant. The results indicate that this technology can provide meaningful insight into the design of fiber composite hip implants.

Blake, T. A.↗
NASA NTRS1982

Computer modeling of thermoelectric generator performance

Features of the DEGRA 2 computer code for simulating the operations of a spacecraft thermoelectric generator are described. The code models the physical processes occurring during operation. Input variables include the thermoelectric couple geometry and composition, the thermoelectric materials' properties, interfaces and insulation in the thermopile, the heat source characteristics, mission trajectory, and generator electrical requirements. Time steps can be specified and sublimation of the leg and hot shoe is accounted for, as are shorts between legs. Calculations are performed for conduction, Peltier, Thomson, and Joule heating, the cold junction can be adjusted for solar radition, and the legs of the thermoelectric couple are segmented to enhance the approximation accuracy. A trial run covering 18 couple modules yielded data with 0.3% accuracy with regard to test data. The model has been successful with selenide materials, SiGe, and SiN4, with output of all critical operational variables.

Chmielewski, A. B.↗
NASA NTRS1974

Effect degree of crosslinking on the tearing energy

Much recent work has been carried out on the tear behavior of elastomers, both filled and unfilled. By use of a criterion for tearing involving the concept of the tearing energy, the effects of variables such as test temperature, test rate, specimen geometry, and chemical nature of the elastomer have been investigated. The one variable which has not yet been studied is the specific effect of changes in the degree of crosslinking on tear behavior. By use of data published in the literature on the smooth tear behavior of unfilled vulcanizates, it is shown that these data can all be superposed onto a common response curve when the proper normalizations are applied.

Fedors, R. F.↗
NASA NTRSDate not supplied

Influence of Thermophysical Property Variability on Thermal Predictions of Ti-6Al-4V

The additive manufacturing (AM) industry has experienced rapid growth in recent decades as industrial interest in the process has grown. Because of this, there are many groups interested in simulations of the AM process. However, the influence of thermophysical property variability on the melt pool geometry during processing of various AM alloys is unclear. The goal of my work at NASA Langley Research Center (LaRC) was to characterize this influence on Ti-6Al-4V during AM processing alongside developing a tool to enable equivalent studies on other AM materials. To facilitate this process, a database tool was developed to contain and organize thermophysical data previously reported by primary sources. The specific thermophysical properties of interest for this study were density, specific heat capacity, and conductivity. Thermal diffusivity was calculated using the other three properties. This data was then fit with a Gaussian distribution and then randomly sampled from using Monte Carlo random value sampling. Using the Rosenthal equation, this sample data was used to simulate the temperature field during additive manufacturing and extract the melt pool geometry. Specifically, the melt pool’s length, width, and depth. This process was repeated an arbitrary number of times, with the default being 1000. Once this information was obtained, histograms were made showing the distributions of the sizes of the melt pool’s length, width, and depth. Representative statistical metrics of the distributions were calculated (mean, standard deviation, and coefficient of variance). This work found that at the simulated processing values, the melt pool’s width and depth had a 5.7% variation while the length had a 3.2% variation. Additionally, a tool was constructed to graph a thermal color map representation of the melt pool for specific, arbitrary values of density, specific heat, and conductivity. This tool allowed for more efficient plotting of individual queries of the thermophysical properties. The results that were observed in the research were that values reported in literature vary and this variance can have a significant impact on the simulation. Predictions of the melt pool’s dimensions show that length has a standard deviation of approximately 6 μm, width has a standard deviation of approximately 5 μm, and depth can vary by approximately 3 μm. Considering the mean sizes of length, width, and depth are 185 μm, 88 μm, and 44 μm respectively, such a deviation is significant. This shows that depth, for example, could be more than 10% larger or smaller than expected. This demonstrates that variability in the reported thermophysical properties are not negligible and should be expected to have an influence on the results of the laser powder bed fusion additive manufacturing process. When simulating this process in the future, measures should be taken to account for this discrepancy and the uncertainty involved

Justin Martin↗
NASA NTRS1972

Phased array antenna matching: Simulation and optimization of a planar phased array of circular waveguide elements

A computerized simulation of a planar phased array of circular waveguide elements is reported using mutual coupling and wide angle impedance matching in phased arrays. Special emphasis is given to circular polarization. The aforementioned computer program has as variable inputs: frequency, polarization, grid geometry, element size, dielectric waveguide fill, dielectric plugs in the waveguide for impedance matching, and dielectric sheets covering the array surface for the purpose of wide angle impedance matching. Parameter combinations are found which produce reflection peaks interior to grating lobes, while dielectric cover sheets are successfully employed to extend the usable scan range of a phased array. The most exciting results came from the application of computer aided optimization techniques to the design of this type of array.

Dudgeon, J. E.↗
NASA NTRS1974

Craters on Earth, Moon, and Mars - Multivariate classification and mode of origin

Testing extraterrestrial craters and candidate terrestrial analogs for morphologic similitude is treated as a problem in numerical taxonomy. According to a principal-components solution and a cluster analysis, 402 representative craters on the Earth, the Moon, and Mars divide into two major classes of contrasting shapes and modes of origin. Craters of net accumulation of material (cratered lunar domes, Martian calderas, and all terrestrial volcanoes except maars and tuff rings) group apart from craters of excavation (terrestrial meteorite impact and experimental explosion craters, typical Martian craters, and all other lunar craters). Maars and tuff rings belong to neither group but are transitional. The classification criteria are four independent attributes of topographic geometry derived from seven descriptive variables by the principal-components transformation. Morphometric differences between crater bowl and raised rim constitute the strongest of the four components.

Pike, R. J.↗
NASA NTRS1975

Static and wind tunnel model tests for the development of externally blown flap noise reduction techniques

Externally blown flap models were tested for noise and performance at one-fifth scale in a static facility and at one-tenth scale in a large acoustically-treated wind tunnel. The static tests covered two flap designs, conical and ejector nozzles, third-flap noise-reduction treatments, internal blowing, and flap/nozzle geometry variations. The wind tunnel variables were triple-slotted or single-slotted flaps, sweep angle, and solid or perforated third flap. The static test program showed the following noise reductions at takeoff: 1.5 PNdB due to treating the third flap; 0.5 PNdB due to blowing from the third flap; 6 PNdB at flyover and 4.5 PNdB in the critical sideline plane (30 deg elevation) due to installation of the ejector nozzle. The wind tunnel program showed a reduction of 2 PNdB in the sideline plane due to a forward speed of 43.8 m/s (85 kn). The best combination of noise reduction concepts reduced the sideline noise of the reference aircraft at constant field length by 4 PNdB.

Pennock, A. P.↗
NASA NTRS1976

Inlet/nacelle/exhaust system integration for the QCSEE propulsion systems

The key features of the integrated propulsion systems developed for short haul aircraft are discussed including the high Mach number, fixed geometry, near sonic inlet, the variable area nozzles, thrust reversing systems, and aircraft accessory location. The roles and interplay of each element are considered and comparisons are made with conventional state-of-the-art technology.

Kutney, J. T.↗