Results for “transitivity” — Page 24

NASA NTRSDate not supplied

Enhancements to Linear Stability-Based, CFD-integrated Transition Prediction for High-Speed Flows

Combining linear stability calculations with computational fluid dynamics (CFD) simulations has great potential for the automated modeling of high-speed flows, especially when adequate information about the configuration and the disturbance environment is available. However, a significant impediment to the applicability of this technique is the lack of an efficient method to calculate the crucial amplification ratio corresponding to the onset of transition in hypersonic flows. This ratio, also known as the "transition N-factor," is dependent upon the freestream disturbance environment as well as the surface properties of the test article. In response to the need for an engineering solution to predict the transition N-factor within conventional hypersonic wind tunnels, this paper presents a data-driven correlation that expands the existing correlations from straight circular cones with a narrow range of half angles to a broader array of axisymmetric configurations. Furthermore, when tested against a chosen dataset that was not used in its calibration, the suggested correlation shows good predictive accuracy with an RMS error of only 6.9%. Although similar accuracy may also be achieved via existing correlations based on similar datasets, predictions based on the proposed correlation have the advantage of not requiring an extensive amount of configuration-specific data. Practical applications often have access to the input parameters needed for this correlation, such as the freestream disturbance intensity, Mach number, and body-based slenderness Reynolds number. Additionally, this correlation outperforms the traditional assumption of a constant N-factor, particularly for configurations with blunted nose geometries. The development of this correlation is grounded in an extensive dataset encompassing conical models with body half-angles varying between 5 degrees and 16 degrees, Mach numbers ranging from 5 to 14, and nosetip-based Reynolds numbers approaching the transition reversal limit for blunt-nosed cones.

CFD↗

NASA NTRSDate not supplied

Enhancements to Linear Stability-Based, CFD-integrated Transition Prediction for High-Speed Flows

Combining linear stability calculations with computational fluid dynamics (CFD) simulations has great potential for the automated modeling of high-speed flows, especially when adequate information about the configuration and the disturbance environment is available. However, a significant impediment to the applicability of this technique is the lack of an efficient method to calculate the crucial amplification ratio corresponding to the onset of transition in hypersonic flows. This ratio, also known as the "transition N-factor," is dependent upon the freestream disturbance environment as well as the surface properties of the test article. In response to the need for an engineering solution to predict the transition N-factor within conventional hypersonic wind tunnels, this paper presents a data-driven correlation that expands the existing correlations from straight circular cones with a narrow range of half angles to a broader array of axisymmetric configurations. Furthermore, when tested against a chosen dataset that was not used in its calibration, the suggested correlation shows good predictive accuracy with an RMS error of only 6.9%. Although similar accuracy may also be achieved via existing correlations based on similar datasets, predictions based on the proposed correlation have the advantage of not requiring an extensive amount of configuration-specific data. Practical applications often have access to the input parameters needed for this correlation, such as the freestream disturbance intensity, Mach number, and body-based slenderness Reynolds number. Additionally, this correlation outperforms the traditional assumption of a constant N-factor, particularly for configurations with blunted nose geometries. The development of this correlation is grounded in an extensive dataset encompassing conical models with body half-angles varying between 5 degrees and 16 degrees, Mach numbers ranging from 5 to 14, and nosetip-based Reynolds numbers approaching the transition reversal limit for blunt-nosed cones.

CFD↗

NASA NTRSDate not supplied

Transition Measurements on the SWiFT Model in the National Transonic Facility

Boundary layer transition locations on the Swept Wing Flow Test (SWiFT) Hybrid Wing Body model were measured in the National Transonic Facility (NTF) at the NASA Langley Research Center using several different methods. These methods include sublimating chemical flow visualization for a limited number of low Reynolds number conditions, as well as mean static pressure and dynamic pressure measurements. Results are presented for a range of conditions in the NTF, demonstrating Mach and Reynolds number effects. The transition front locations obtained from the different techniques agree well. A variation of the static pressure transition detection method is described in which continuous angle of attack polars are performed. This approach enables detection of the transition front at more challenging (high Reynolds number) conditions than is possible with sparser data from pitch-pause angle-of-attack polars. The trip dot effectiveness is also verified using all of the available diagnostics. Additionally, low Reynolds number results are compared with those acquired on the same model at the Aircraft Research Association (ARA) facility, and these results show good agreement overall, suggesting similar freestream flow quality conditions of the two facilities.

National Transonic Facility↗

NASA NTRSDate not supplied

Transition Measurements on the SWiFT Model in the National Transonic Facility

Boundary layer transition locations on the Swept Wing Flow Test (SWiFT) Hybrid Wing Body model were measured in the National Transonic Facility (NTF) at the NASA Langley Research Center using several different methods. These methods include sublimating chemical flow visualization for a limited number of low Reynolds number conditions, as well as mean static pressure and dynamic pressure measurements. Results are presented for a range of conditions in the NTF, demonstrating Mach and Reynolds number effects. The transition front locations obtained from the different techniques agree well. A variation of the static pressure transition detection method is described in which continuous angle of attack polars are performed. This approach enables detection of the transition front at more challenging (high Reynolds number) conditions than is possible with sparser data from pitch-pause angle-of-attack polars. The trip dot effectiveness is also verified using all of the available diagnostics. Additionally, low Reynolds number results are compared with those acquired on the same model at the Aircraft Research Association (ARA) facility, and these results show good agreement overall, suggesting similar freestream flow quality conditions of the two facilities.

National Transonic Facility↗

NASA NTRS2023

CFD Integrated Transition Modeling for High-Speed Flows via Coupled OVERFLOW-LASTRAC Analysis

This work details ongoing efforts at the NASA Langley Research Center to develop and validate a general-use CFD tool that includes built-in predictions of boundary-layer transition in high-speed flows. Existing tools for the coupling of the NASA OVERFLOW structured overset RANS solver and LASTRAC stability analysis code have been extended to capture boundary-layer transition in high-speed flows driven by either Mack’s first-mode or secondmode instabilities and/or crossflow instabilities. The efficacy of this coupled approach has been demonstrated by examining a variety of supersonic and hypersonic test cases for which experimental validation data is available. The intermittency prescription parameters inherited from prior low-speed applications are found to be suitable for some, but not all high-speed flow scenarios. The method is found to be robust for straight cone configurations and improvements necessary to accurately capture transition on geometries with spatially complex amplification factor envelopes with intermediate regions of slow N-factor variation are examined. The automated, coupled analysis is demonstrated for a 3d supersonic test case and found to perform well within the limits of the linear stability analysis on which it relies. Finally, a preliminary investigation of the method’s robustness to non-ideal CFD meshes is conducted.

High-speed flow↗

NASA NTRS1971

Analysis of Free-Flight Laminar, Transitional, and Turbulent Heat-Transfer Results at Free-Stream Mach Numbers Near 20 (Reentry F)

Laminar, transitional, and turbulent heat-transfer data were measured during a reentry flight at a Mach number of 20 on a 5 deg half-angle cone 3.962 m (13 ft) long with an initial nose tip radius of 0.254 cm (0.1 in.). The free-stream Reynolds number increased during the prime data period from 7.0 x 10(exp 6) to 51.5 x 10(exp 6) per meter (2.1 x 10(exp 6) to 15.7 x 10(exp 6) per foot) and the ratio of wall to total temperature varied from 0.053 to 0.12. The angle of attack was less than 1deg for the prime data period. The experimental laminar and turbulent heating rates are compared with results from existing flat-plate prediction methods. At conditions of minimal tip blunting and angle of attack (above 26.8 km (88 000 ft)), values from a flat-plate laminar method agreed within 20 percent with the laminar data. The Schultz-Grunow skin-friction equation with reference enthalpy; conditions, with the Reynolds number based on distance from the transition location, and with the Colburn Reynolds analogy agreed within 10 percent with the experimental turbuleiit heating data. The Van Driest n skin-friction equation with Reynolds number greater than 10(exp 7) based on distance from the peak heating point and the Colburn Reynolds analogy was also within approximately 10 percent of the experimental turbulent heating data. A data correlation jbf the extent of transition and a simple empirical transition-zone heating correlation were also presented.

Zoby, Ernest V.↗

NASA NTRS1971

Boundary layer transition detection on the X-15 vertical fin using surface-pressure-fluctuation measurements

A flush-mounted microphone on the vertical fin of an X-15 airplane was used to investigate boundary layer transition phenomenon during flights to peak altitudes of approximately 70,000 meters. The flight results were compared with those from wind tunnel studies, skin temperature measurements, and empirical prediction data. The Reynolds numbers determined for the end of transition were consistent with those obtained from wind tunnel studies. Maximum surface-pressure-fluctuation coefficients in the transition region were about an order of magnitude greater than those for fully developed turbulent flow. This was also consistent with wind tunnel data. It was also noted that the power-spectral-density estimates of the surface-pressure fluctuations were characterized by a shift in power from high frequencies to low frequencies as the boundary layer changed from turbulent to laminar flow. Large changes in power at the lowest frequencies appeared to mark the beginning of transition.

Lewis, T. L.↗

NASA NTRS1972

Analysis of flight data on boundary layer transition at high angles of attack

Boundary layer transition data were obtained on the flight of two cones which reentered at velocities of about 7.0 km/sec. One cone reentered at a nominal zero degree angle of attack and the other, due to an anomaly above the earth atmosphere, reentered at local angles of attack up to 7.0 km/sec. The transition data were obtained from on-board acoustic and electrostatic sensors. A description of the design, calibration, and method used to detect transition from the sensors is included. The flow field calculation used to obtain the local flow properties on the cones is described. Finally, the transition data found from both cone flights is correlated.

Haigh, W. W.↗

NASA NTRS1972

Role of phonons in the metal-insulator phase transition.

Review, for the transition series oxides, of the Mattis and Lander model, which is one of electrons interacting with lattice vibrations (electron and phonon interaction). The model displays superconducting, insulating, and metallic phases. Its basic properties evolve from a finite crystallographic distortion associated with a dominant phonon mode and the splitting of the Brillouin zone into two subzones, a property of simple cubic and body centered cubic lattices. The order of the metal-insulator phase transition is examined. The basic model has a second-order phase transition and the effects of additional mechanisms on the model are calculated. The way in which these mechanisms affect the magnetically ordered transition series oxides as described by the Hubbard model is discussed.

Langer, W. D.↗

NASA NTRS1972

Corrections to vibrational transition probabilities calculated from a three-dimensional model.

Corrections to the collision-induced vibration transition probability calculated by Hansen and Pearson from a three-dimensional semiclassical model are examined. These corrections come from the retention of higher order terms in the expansion of the interaction potential and the use of the actual value of the deflection angle in the calculation of the transition probability. It is found that the contribution to the transition cross section from previously neglected potential terms can be significant for short range potentials and for the large relative collision velocities encountered at high temperatures. The correction to the transition cross section obtained from the use of actual deflection angles will not be appreciable unless the change in the rotational quantum number is large.

Stallcop, J. R.↗

NASA NTRS1972

The relative age of the transition zone between Hellas and the Martian cratered terrain.

Consideration of the relationships of craters to scarps and ridges and of the antiquity of Hellas relative to the cratered terrain. Scarps and ridges in the transition zone between Hellas and the cratered terrain both postdate and predate large craters. It appears that there are a number of craters which are older than the transition zone structures, which in turn are presumably related in some way to the formation of Hellas. Sharp et al. (1971) have suggested impact, large-scale volcanic explosion, or subsidence for the origin of Hellas. Volcanic explosion seems the least likely explanation, for the resulting deficiency of mass beneath Hellas should induce later isostatic rebound, contrary to observations of the transition zone which imply subsidence relatively late in the history of the Martian surface. An origin of Hellas by impact with later isostatic subsidence (because of a dense mass under its floor, as suggested by Sharp et al.) to account for the characteristics of the transition zone seems to be the best model, and may also account for the featureless floor of the basin.

Thorman, C. H.↗

NASA NTRS1972

Structure of the chromosphere-corona transition region.

The structure and energy balance of the chromosphere-corona transition region is investigated by means of a static, planar model which is compared with the results of XUV-resonance-line observations. In this model, the transition region is heated by thermal conduction from the corona and cooled by radiative losses. Comparison of the model with observational results implies that this is the dominant process in the energy balance of the transition region, and that the base of the transition region is inherently nonstatic and/or nonplanar. The model explains the observational finding of Noyes et al. (1970) that the number density and the downward heat flux both increase by the same factor from quiet regions to active regions.

Moore, R. L.↗

NASA NTRS1972

The effect of angle of attack on boundary-layer transition on cones.

Boundary-layer transition on 5- and 15-deg half-angle cones was studied as a function of angle of attack (ranging from 0 to 20 deg) in a 3.5 ft hypersonic wind tunnel at a freestream Mach number of 7.4. It is shown that the influence of the angle of attack on the transition Reynolds number is a function of the meridian angle. On the windward ray of the 15-deg cone, transition Reynolds numbers show an initial slight increase and then a decrease with increasing angle of attack; leeward-ray Reynolds numbers for this cone decrease rapidly with angle of attack. Windward-ray transition Reynolds numbers increase monotonically with angle of attack on the 5-deg cone, but the effect of the angle of attack on the leeward ray is the same as for the 15-deg cone.

Mateer, G. G.↗

NASA NTRS1972

Evaluation of tantalum 316 stainless steel transition joints

Tubular transition joints providing a metallurgically bonded connection between tantalum and 316 stainless steel pipe sections were comparatively evaluated for durability under thermal cycling conditions approximating the operation of a SNAP-8 mercury boiler. Both coextruded and vacuum brazed transition joints of 50mm (2 inch) diameter were tested by thermal cycling 100 times between 730 C and 120 C(1350 F and 250 F) in a high vacuum environment. The twelve evaluated transition joints survived the full test sequence without developing leaks, although liquid penetrant bond line indications eventually developed in all specimens. The brazed transition joints exhibited the best dimensional stability and bond line durability.

Stoner, D. R.↗

NASA NTRS1973

Ultrasonic investigation of the nematic-isotropic phase transition in MBBA.

Relaxation processes associated with the nematic-isotropic phase transition are investigated in liquid crystals of p-methoxybenzylidine-p-n-butylaniline. Sound velocity and absorption are measured at frequencies from 0.3 to 23 MHz at temperatures from 23 to 77 C in samples without preferred orientations. Particular attention is given to the region of transition at about 44 C. Sound absorption and velocity dispersion far from the phase transition region can be well described by a single relaxation process, while in the vicinity of the phase transition the acoustic properties are characteristic of a multiply relaxing fluid.

Eden, D.↗

NASA NTRS1974

Experimental studies of hypersonic boundary-layer transition and effects of wind tunnel disturbances

Boundary layer transition data on cones and free stream disturbance levels were measured in a hypersonic wind tunnel and Mach 8 variable density hypersonic tunnel. Transition data were obtained by using different conical models and techniques for detecting the location of transition. The disturbance levels were measured by using hot wire anemometry and pressure transducers. The transition Reynolds numbers obtained from the tests correlated well when the fluctuating pressures measured at the surface of conical models were used as a correlating parameter.

Stainback, P. C.↗

NASA NTRS1973

Continuum ionization transition probabilities of atomic oxygen

The technique of photoelectron spectroscopy was used to obtain the relative continuum transition probabilities of atomic oxygen at 584 A for transitions from 3P ground state into the 4S, D2, and P2 states of the ion. Transition probability ratios for the D2 and P2 states relative to the S4 state of the ion are 1.57 + or - 0.14 and 0.82 + or - 0.07, respectively. In addition, transitions from excited O2(a 1 Delta g) state into the O2(+)(2 Phi u and 2 Delta g) were observed. The adiabatic ionization potential of O2(+)(2 Delta g) was measured as 18.803 + or - 0.006 eV.

Samson, J. R.↗

NASA NTRS1974

Comparison of transition and freestream disturbance measurements obtained in two wind tunnel facilities

Boundary-layer transition measurements have been made on two 5-deg half-angle cones at Mach 7 in the Ames 3.5-foot and the Langley variable density wind tunnels. Although there were differences between the measured freestream disturbance scales and pressure fluctuation levels, the choice of consistent locations within the transition region, using either thin-film fluctuation or surface heat-transfer data results in excellent agreement between the transition Reynolds numbers in both facilities. However, there is an apparent connection between changes in freestream pressure fluctuation levels and movement of boundary-layer transition location in the two facilities.

Owen, F. K.↗