Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “test approach”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Flight test evaluation of precision-code differential GPS for terminal approach and landing

A flight test evaluation conducted at the NASA Ames Research Center of precision-code differential GPS for terminal approach and landing is described. Differential corrections to satellite range and range-rate measurements are computed in a stationary ground reference system, uplinked to the test aircraft, and employed to correct corresponding airborne satellite data. Differentially corrected range and range-rate data, combined with inertial data, are then utilized with satellite position and velocity to compute aircraft position and velocity employing an eight-state extended Kalman filter.

Mcnally, B. D.↗
NASA NTRS1988

An approach for detecting post-launch spectral changes in satellite multispectral sensors

An approach for testing whether or not post-launch changes have occurred in sensor spectral responses is described. The approach uses field measurements of ground targets having differing spectral reflectance properties as well as calculations based on the original spectral response characteristics. As an example, a shift in band location was modeled and evaluated through the simulation of signals from soil and vegetation targets in the spectral bands of five satellite systems.

Suits, G. H.↗
NASA NTRS1991

Life testing of secondary silver-zinc cells

Testing on a variety of secondary silver-zinc (Ag-Zn) cells has been in progress at the Marshall Space Flight Center (MSFC) for over six years. The latest test involves a 350-Ah cell design that has been cycled at 10 C for 16 months. This design has achieved over 7200 low-earth-orbit (LEO) cycles as well as 17 deep discharges at an 85 percent depth of discharge. This test not only is a life test on these cells but also addresses different methods of storing these cells between the deep discharges. As the test is approaching completion, some interesting results are being seen. In particular, two of the four packs currently on test have failed to meet the 35-h (295-Ah) deep discharge requirement that was arbitrarily set at the beginning of the test. This capacity loss failure is likely a result of the storage method used on these two packs between deep discharges. The two packs are LEO cycled in such a way as to minimize overcharge in an attempt to prolong life.

Brewer, Jeffrey C.↗
NASA NTRS2017

Spectro-Photometer for the History of the Universe, Epoch of Reionization, and Ices Explorer, One Quarter Scale Prototype Thermal Testing

The Spectro-Photometer for the History of the Universe, Epoch of Reionization, and Ices Explorer (SPHEREx) instrument has been proposed as NASA Small Explorer (SMEX) and Medium Explorer (MIDEX) missions designed to perform an all-sky near-infrared survey. The primary science objective of the SPHEREx instrument is the mapping and cataloging of data on galaxy red shifts and absorption spectra. The SPHEREx instrument utilizes a linear variable band pass filter to provide discrete spectral coverage of the 0.75 to 5.0 μm range. The nominal on-orbit mission lifetime for the instrument is two years with continuous primary science imaging. The SPHEREx instrument will be placed in a near-circular LEO sun-synchronous terminator orbit with a mean altitude of 600 km, and solar beta angles ranging from 59° to 90°. A passive V-groove radiator cooling system was selected for the SPHEREx instrument. This design was chosen for its simplicity and lack of vibration. It includes five radiator stages with the coldest two stages providing temperatures below 80K and 55K for the 2.5μm and 5.3μm detectors respectively. A one quarter scale thermal prototype was constructed to characterize the performance of the SPHEREx thermal control subsystem. This prototype was directly derived and scaled from the current flight design, and accurately replicates all heat flow paths at scale. The prototype was tested in two bounding hot flight-like environments in the Cryogenic Systems Engineering, Advanced Thermal Technology Lab at NASA’s Jet Propulsion Laboratory. Following testing, a previously developed one quarter scale thermal model was correlated to the two conditions seen in test. The resultant correlated model is able to predict the prototype test temperatures to within 1K for all critical radiator stages. An overview of the thermal control design approach, the test configuration, and test and correlation results are presented.

Bolton, Douglas A.↗
NASA NTRS1980

NASA/FAA flight-test investigation of helicopter microwave landing system approaches

The helicopter Microwave Landing System flight-test investigations, conducted by a joint NASA/FAA effort in order to gather statistical data for establishing terminal instrument procedures criteria, and to provide a performance data base for developing advanced MLS guidance concepts, are presented. The specific flight-test objectives were to: (1) develop acceptable angle-only MLS approach profiles; (2) determine tracking errors; (3) determine altitude loss during missed approach; (4) evaluate guidance display sensitivities; and (5) evaluate pilot acceptability. Fourteen pilots flew 140 manual (without stability augmentation) dual-pilot simulated instrument approaches in a UH-1H helicopter. The flight profiles flown included 3-, 6-, and 9-degree glideslope, centerline approaches to decision heights of 50, 100, and 150 ft, respectively. The angular guidance display sensitivities and the data acquisition system are also described. Eight major conclusions are made, and include the following: (1) the use of pitch attitude to control airspeed and collective to control glideslope was the preferred pilot technique for the steep glideslope approaches, and (2) angular guidance deviation indicator sensitivity requirements for helicopter MLS approaches to STOLports and heliports have been found to be significantly different from standard ILS sensitivities.

Peach, I. L., Jr.↗
NASA NTRSDate not supplied

Computational Fluid Dynamics Models of the NASA White Sands Test Facility Particle Impact Test Nozzles

The particle impact ignition mechanism is considered to be the most effective means for igniting metals in gaseous oxygen environments and is a concern for every oxygen system. For this reason, the National Aeronautics and Space Administration (NASA) commits a large amount of resources attempting to understand and defend against this phenomenon. The most practical means of accomplishing this is through extensive of testing. To this end, over the years NASA has developed and built a facility and various apparatuses to test material or component vulnerability to a particle impact ignition. In testing materials, NASA uses sub-sonic and supersonic nozzles to replicate the conditions that a material is expected to experience in service. However, challenges include obtaining an understanding of the gas dynamics and of the particle behavior through and up to the point of impact at the material under test. One means of addressing these challenges is the use of computational fluid dynamics (CFD). If a CFD model can be built and validated, the model can then be used to confidently interrogate changes to inlet conditions and particle geometries, as well as changes to nozzle geometries to better simulate a material’s in-situ conditions and greatly reduce or eliminate trial-and-error approaches in testing. This paper will show NASA’s approach to and results of using CFD to better understand their particle impact nozzles.

Computational Fluid Dynamics↗
NASA NTRS2000

The Use of Environmental Test Facilities for Purposes Beyond Their Original Design

Increasing demands from space flight project offices are requiring environmental testing facilities to become more versatile with increased capabilities. At the same time, maintaining a cost-effective approach to test operations has driven efforts to use these facilities for purposes beyond their original design. This paper presents an overview of the Jet Propulsion Laboratory's efforts to provide JPL's space flight projects with test facilities to meet unique test requirements and to serve the needs of selected outside customers. The large number of recent Mars Missions, including the Mars Pathfinder project, have required testing of components and systems in a Martian surface environment in facilities originally designed for deep space testing. The unique problems associated with performing these tests are discussed, along with practical solutions. Other unique test requirements are discussed including the use of space simulation chambers for testing high altitude balloon gondolas and the use of vacuum chambers for system level test firing of an ion propulsion engine.

Fisher, Terry C.↗
NASA NTRS2017

Design and Fabrication of a Composite Morphing Radiator Panel Using High Conductivity Fibers

Upcoming crewed space missions will involve large internal and external heat loads and require advanced thermal control systems to maintain a desired internal environment temperature. Radiators with at least 12:1 turndown ratios (the ratio between the maximum and minimum heat rejection rates) will be needed. However, current technologies are only able to achieve turndown ratios of approximately 3:1. A morphing radiator capable of altering shape could significantly increase turndown capabilities. Shape memory alloys offer qualities that may be well suited for this endeavor; their temperature-dependent phase changes could offer radiators the ability to passively control heat rejection. In 2015, a morphing radiator prototype was constructed and tested in a thermal vacuum environment, where it successfully demonstrated the morphing behavior and variable heat rejection. Newer composite prototypes have since been designed and manufactured using two distinct types of SMA materials. These models underwent temperature cycling tests in a thermal vacuum chamber and a series of fatigue tests to characterize the lifespan of these designs. The focus of this paper is to present the design approach and testing of the morphing composite facesheet. The discussion includes: an overall description of the project background, definition of performance requirements, composite materials selection, use of analytic and numerical design tools, facesheet fabrication, and finally fatigue testing with accompanying results.

Wescott, Matthew T.↗
NASA NTRS1984

Some real-time simulation applications to Space Shuttle approach and landing design and test

In the present discussion of the roles played by real time, man-in-the-loop engineering simulation in the development of NASA Space Shuttle approaches and landings, attention is given to the function of the simulator as a design and verification tool. Aspects of the problem posed by Shuttle landings, and the difficulties involved in this problem's quantification, are noted. Recent results of control system studies for pitch axis control, using fixed- and motion-base simulators, are discussed.

Law, H. G., III↗
NASA NTRS1989

B-737 flight test of curved-path and steep-angle approaches using MLS guidance

A series of flight tests were conducted to collect data for jet transport aircraft flying curved-path and steep-angle approaches using Microwave Landing System (MLS) guidance. During the test, 432 approaches comprising seven different curved-paths and four glidepath angles varying from 3 to 4 degrees were flown in NASA Langley's Boeing 737 aircraft (Transport Systems Research Vehicle) using an MLS ground station at the NASA Wallops Flight Facility. Subject pilots from Piedmont Airlines flew the approaches using conventional cockpit instrumentation (flight director and Horizontal Situation Indicator (HSI). The data collected will be used by FAA procedures specialists to develop standards and criteria for designing MLS terminal approach procedures (TERPS). The use of flight simulation techniques greatly aided the preliminary stages of approach development work and saved a significant amount of costly flight time. This report is intended to complement a data report to be issued by the FAA Office of Aviation Standards which will contain all detailed data analysis and statistics.

Branstetter, J. R.↗
NASA NTRS2007

Feasibility of Turing-Style Tests for Autonomous Aerial Vehicle "Intelligence"

A new approach is suggested to define and evaluate key metrics as to autonomous aerial vehicle performance. This approach entails the conceptual definition of a "Turing Test" for UAVs. Such a "UAV Turing test" would be conducted by means of mission simulations and/or tailored flight demonstrations of vehicles under the guidance of their autonomous system software. These autonomous vehicle mission simulations and flight demonstrations would also have to be benchmarked against missions "flown" with pilots/human-operators in the loop. In turn, scoring criteria for such testing could be based upon both quantitative mission success metrics (unique to each mission) and by turning to analog "handling quality" metrics similar to the well-known Cooper-Harper pilot ratings used for manned aircraft. Autonomous aerial vehicles would be considered to have successfully passed this "UAV Turing Test" if the aggregate mission success metrics and handling qualities for the autonomous aerial vehicle matched or exceeded the equivalent metrics for missions conducted with pilots/human-operators in the loop. Alternatively, an independent, knowledgeable observer could provide the "UAV Turing Test" ratings of whether a vehicle is autonomous or "piloted." This observer ideally would, in the more sophisticated mission simulations, also have the enhanced capability of being able to override the scripted mission scenario and instigate failure modes and change of flight profile/plans. If a majority of mission tasks are rated as "piloted" by the observer, when in reality the vehicle/simulation is fully- or semi- autonomously controlled, then the vehicle/simulation "passes" the "UAV Turing Test." In this regards, this second "UAV Turing Test" approach is more consistent with Turing s original "imitation game" proposal. The overall feasibility, and important considerations and limitations, of such an approach for judging/evaluating autonomous aerial vehicle "intelligence" will be discussed from a theoretical perspective.

Young, Larry A.↗
NASA NTRS2012

Aerothermal Ground Testing of Flexible Thermal Protection Systems for Hypersonic Inflatable Aerodynamic Decelerators

Flexible TPS development involves ground testing and analysis necessary to characterize performance of the FTPS candidates prior to flight testing. This paper provides an overview of the analysis and ground testing efforts performed over the last year at the NASA Langley Research Center and in the Boeing Large-Core Arc Tunnel (LCAT). In the LCAT test series, material layups were subjected to aerothermal loads commensurate with peak re-entry conditions enveloping a range of HIAD mission trajectories. The FTPS layups were tested over a heat flux range from 20 to 50 W/cm with associated surface pressures of 3 to 8 kPa. To support the testing effort a significant redesign of the existing shear (wedge) model holder from previous testing efforts was undertaken to develop a new test technique for supporting and evaluating the FTPS in the high-temperature, arc jet flow. Since the FTPS test samples typically experience a geometry change during testing, computational fluid dynamic (CFD) models of the arc jet flow field and test model were developed to support the testing effort. The CFD results were used to help determine the test conditions experienced by the test samples as the surface geometry changes. This paper includes an overview of the Boeing LCAT facility, the general approach for testing FTPS, CFD analysis methodology and results, model holder design and test methodology, and selected thermal results of several FTPS layups.

Bruce, Walter E., III↗
NASA NTRS2017

Online Multi-Modal Learning and Adaptive Information Trajectory Planning for Autonomous Exploration

In robotic information gathering missions, scientists are typically interested in understanding variables which require proxy measurements from specialized sensor suites to estimate. However, energy and time constraints limit how often these sensors can be used in a mission. Robots are also equipped with cheaper to use navigation sensors such as cameras. In this paper, we explore a challenging planning problem in which a robot is required to learn about a scientific variable of interest in an initially unknown environment by planning informative paths and deciding when and where to use its sensors. To tackle this we present two innovations: a Bayesian generative model framework to automatically learn correlations between expensive science sensors and cheaper to use navigation sensors online, and a sampling based approach to plan for multiple sensors while handling long horizons and budget constraints. Our approach does not grow in complexity with data and is anytime making it highly applicable to field robotics. We tested our approach extensively in simulation and validated it with real data collected during the 2014 Mojave Volatiles Prospector Mission. Our planning algorithm performs statistically significantly better than myopic approaches and at least as well as a coverage-based algorithm in an initially unknown environment while having added advantages of being able to exploit prior knowledge and handle other intricacies of the real world without further algorithmic modifications.

learning↗
NASA NTRS2019

Why is UTM Needed?

This presentation is to provide an overview of NASA's Unmanned Aircraft Systems (UAS) Traffic Management research and testing. The content presents the background and need for a UTM system and the concept elements incorporated in the approach. The testing conducted within the project, the architecture, and overall impact of the research is presented as well.

NASA↗
NASA NTRS1976

Flight-test measurement of the noise reduction of a jet transport delayed flap approach procedure

A delayed flap approach procedure was flight tested using the NASA CV-990 airplane to measure and analyze the noise produced beneath the flight path. Three other types of landing approaches were also flight tested to provide a comparison of the noise reduction benefits to the delayed flap approach. The conventional type of approach was used as a baseline to compare the effectiveness of the other approaches. The decelerating approach is a variation of the delayed flap approach. A detailed comparison of the ground perceived noise generated during the approaches is presented. For this comparison, the measured noise data were normalized to compensate for variations in aircraft weight and winds that occurred during the flight tests. The data show that the reduced flap approach offers some noise reduction, while the delayed flap and decelerating approaches offer significant noise reductions over the conventional approach.

Foster, J. D.↗
NASA NTRS1961

Repeatability of the Over-All Errors of an Airplane Altimeter Installation in Landing-Approach Operations

Flight tests have been conducted to determine the repeatability of the over-all altimetry errors in the landing-approach condition of two sensitive altimeters (Air Force type C-12) installed in the cockpit of a transport airplane and of four precision altimeters (Air Force type MA-1) installed in a photo-observer. Data were obtained through a speed range of 62 to 100 knots during 42 landing-approach operations conducted on four different days. The results of the tests show that the repeatability errors of the two sensitive altimeters are +/- 35 feet and +/- 39 feet. These errors are of the same order as the maximum repeatability error measured in previous tests of eleven airplanes of the same type. For each of the four flights of the present tests the mean values of the data obtained with the two sensitive altimeters shifted by relatively large amounts, apparently because of the interaction of the stability and aftereffect- recovery characteristics of the instruments. For concurrent measurements of the over-all errors of the four precision altimeters, it is concluded that for comparable installations, the repeatability errors measured with these altimeters would be smaller than those measured with the sensitive altimeters.

Gracey, William↗
NASA NTRS2018

Fuel Sensitivity of Gas Emissions, Lean Blowout and Combustion Dynamics for a 9-Point LDI Combustor

Fuel sensitivity of gaseous emissions, approach to lean blowout and combustion dynamics are evaluated in this study. Experiments were conducted at the NASA Glenn Research Center's CE-5 flame tube test facility with a 9-point Swirl-Venturi Lean Direct Injection (SV-LDI) combustor. A reference jet fuel (A2) and two test fuels (C1 and C3) from were provided by the National Jet Fuels Combustion Program (NJFCP). C1 is essentially a 2-component iso-paraffin test fuel with a low cetane number of 17, and C3 is a high viscosity test fuel. Approach to lean blowout was monitored in terms of the rapid increase in CO emissions index as equivalence ratio decreased, but testing did not proceed all the way to lean blowout (LBO). Burning C1 was found to produce lower NOx emissions, but C1 flame temperatures were about 25 K higher relative to A2 at near LBO points (where CO emissions increased very rapidly). The NOx emissions of C3 were similar to A2. At low power conditions where fuel injector performance is not optimized for this 9-point LDI combustor, C3 had higher CO emissions than A2 and C1, likely due to C3's higher viscosity relative to A2 and C1. No discernable difference in combustion dynamics was observed between the three fuels tested in the 9-point LDI combustor. While a systematic ignition test campaign was not conducted, it was observed that C1 required a higher equivalence ratio and inlet air temperature for test rig ignition compared to A2 and C3.

Lean Direct Injection↗
NASA NTRS2018

Fuel Sensitivity of Gas Emissions, Lean Blowout and Combustion Dynamics for a 9-Point LDI Combustor

Fuel sensitivity of gaseous emissions, approach to lean blowout and combustion dynamics are evaluated in this study. Experiments were conducted at the NASA Glenn Research Center's CE-5 flame tube test facility with a 9-point Swirl-Venturi Lean Direct Injection (SV-LDI) combustor. A reference jet fuel (A2) and two test fuels (C1 and C3) from were provided by the National Jet Fuels Combustion Program (NJFCP). C1 is essentially a 2-component iso-paraffin test fuel with a low cetane number of 17, and C3 is a high viscosity test fuel. Approach to lean blowout was monitored in terms of the rapid increase in CO emissions index as equivalence ratio decreased, but testing did not proceed all the way to lean blowout (LBO). Burning C1 was found to produce lower NOx emissions, but C1 flame temperatures were about 25 K higher relative to A2 at near LBO points (where CO emissions increased very rapidly). The NOx emissions of C3 were similar to A2. At low power conditions where fuel injector performance is not optimized for this 9-point LDI combustor, C3 had higher CO emissions than A2 and C1, likely due to C3's higher viscosity relative to A2 and C1. No discernable difference in combustion dynamics was observed between the three fuels tested in the 9-point LDI combustor. While a systematic ignition test campaign was not conducted, it was observed that C1 required a higher equivalence ratio and inlet air temperature for test rig ignition compared to A2 and C3.

Combustion dynamics↗