Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “temperature acceleration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Undulator Changes Due To Temperature Excursions

The temperature of the LCLS undulators has not been controlled during storage. The effects of the temperature excursions are documented in this note. After a number of LCLS undulators were tuned, fiducialized, and placed in storage anticipating their use, a test was made to ensure that their properties had not changed. The test revealed, however, that indeed the undulators had changed. Detailed study of this problem followed. We now believe that the gap of the undulators changes permanently when the undulators go through temperature excursions. We have tested the other possible cause, transportation, and do not see gap changes. In this note, we document how the undulators have changed since they were originally tuned. The undulators were tuned and fiducialized in the Magnetic Measurement Facility (MMF). Afterward, many of them (approximately 18) were taken to building 750 for storage during summer and fall 2007. Building 750 had no temperature control. The undulator temperatures went from 20 C, used for tuning, down to approximately 11 C during the winter. In January 2008, three of the undulators were brought back to the MMF for a check. All three undulators showed similar changes. Trajectories, phases, and most undulator properties stayed the same, but the fiducialization (beam axis position relative to tooling balls on the undulator) had changed. Further investigation showed that the undulator gap was altered in a periodic way along the magnetic axis with a net average gap change causing the fiducialization change. A new storage location in building 33 was found and future undulators were placed there. A failure in the temperature control, however, caused the undulators to get too hot. Again the gap changed, but with a different periodic pattern. This note documents the measured changes in the undulators. In particular, it shows the detailed history of undulator 39 which went through both negative and positive temperature excursions.

43 PARTICLE ACCELERATORS↗

Optimal controls for an advanced turbofan engine

Linear optimal control theory is applied to the control synthesis of a high bypass ratio, variable pitch, turbofan engine. The basic control philosophy is to use only a low order dynamic model of the plant coupled with the concept of integral-output states so as to maintain control simplicity yet guarantee integral control of thrust, turbine temperature and other important engine outputs. Linear simulation results indicate that the control system developed provides rapid control of small thrust perturbations and quickly eliminates the effect of unmodelled thrust and temperature disturbances. Large thrust accelerations are obtained in about one half second while the control maintains negligible overshoot in temperature and stall margins.

Slater, G. L.↗

Evaluation of Aluminum Polymer Capacitors for Space Applications

Layered aluminum polymer capacitors (APC) may be viable replacements to currently used chip tantalum capacitors due to their lower ESR, weight, and smaller size. So far, there is a lack of information regarding the reliability of these parts. Available technical literature is mostly related to the effect of humidity. Although APCs have a limited moisture resistance, it may be contained to the level sufficient for space applications. This work analyzes construction and characteristics of seven types of commercial APCs manufactured by four vendors and rated to voltages from 6.3 to 35 V were analyzed. Their reliability under environmental stresses and highly accelerated life tests was assessed in the range of temperatures and voltages to determine reliability acceleration factors. For this purpose, characteristics of the parts, including breakdown voltages, the level of anomalous charging currents (ACC), capacitance, DF, ESR and leakage currents were measured in the process of storage at high-temperatures (from 100 to 150 °C) and high humidity at 85 °C. Monitored highly accelerated life tests have been carried out at temperatures of 85 °C and 125 °C and voltages varying from 1.2 to 1.9 times the rated voltage. Degradation processes and reliability of APCs have been compared to polymer tantalum capacitors.

Alexander A Teverovsky↗

Computing equilibrium free energies through a nonequilibrium quench

Many methods to accelerate sampling of molecular configurations are based on the idea that temperature can be used to accelerate rare transitions. These methods typically compute equilibrium properties at a target temperature using reweighting or through Monte Carlo exchanges between replicas at higher temperatures. A recent paper [G. M. Rotskoff and E. Vanden-Eijnden, Phys. Rev. Lett. 122, 150602 (2019)] demonstrated that accurate equilibrium densities of states can also be computed through a nonequilibrium “quench” process, where sampling is performed at a higher temperature to encourage rapid mixing and then quenched to lower energy states with dissipative dynamics. Here, we provide an implementation of the quench dynamics in LAMMPS and evaluate a new formulation of nonequilibrium estimators for the computation of partition functions or free energy surfaces (FESs) of molecular systems. We show that the method is exact for a minimal model of N-independent harmonic springs and use these analytical results to develop heuristics for the amount of quenching required to obtain accurate sampling. We then test the quench approach on alanine dipeptide, where we show that it gives an FES that is accurate near the most stable configurations using the quench approach but disagrees with a reference umbrella sampling calculation in high FE regions. We then show that combining quenching with umbrella sampling allows the efficient calculation of the free energy in all regions. Moreover, by using this combined scheme, we obtain the FES across a range of temperatures at no additional cost, making it much more efficient than standard umbrella sampling if this information is required. Finally, we discuss how this approach can be extended to solute tempering and demonstrate that it is highly accurate for the case of solvated alanine dipeptide without any additional modifications.

Chemistry↗

Pt Particles on a Dynamic TiO 2 Support in Near-Ambient Conditions−Disentangling Size, Pressure, and Support Effects

Platinum particles on reducible oxides are known to form complex and highly dynamic catalyst systems at elevated pressures and temperatures, often adopting active structures that differ from those found at room temperature and under ultrahigh vacuum (UHV). Here, we study the oxidation and structural evolution of subnanometer Pt clusters and nanoparticles supported on rutile TiO 2 (110) across an oxygen pressure range from UHV to 0.1 mbar, using near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS), scanning tunneling microscopy (STM) under UHV and NAP conditions, and low-energy ion scattering (LEIS). Our results reveal distinct differences in oxidation behavior and thermal stability between Pt nanoparticles and clusters, which are further modulated by the support stoichiometry and oxygen pressure. Small Pt clusters become oxidized even at room temperature but are susceptible to accelerated sintering in 0.1 mbar O 2 at elevated temperatures. In contrast, well-crystallized Pt nanoparticles on near-stoichiometric TiO 2 show weaker oxidation. On a reduced, defective TiO 2 support, Pt instead quickly becomes deeply buried by new titania layers, which are formed during support reoxidation. This process appears to result primarily from interactions of the support with the gas phase, unlike the classical, selflimited encapsulation that is induced by the strong metal−support interaction (SMSI). Finally, we address the full complexity of real catalysts in a direct side-by-side comparison of the single-crystalline model system with a Pt-loaded TiO 2 powder catalyst (P25). We conclude that the stoichiometry of the model supports must be carefully chosen and controlled to accurately reproduce the expected state of powder supports during redox reactions.

metal nanoparticles↗

Thermoregulation in rats: Effects of varying duration of hypergravic fields

The effects of hypergravitational fields on the thermoregulatory system of the rat are examined. The question underlying the investigation was whether the response of the rat to the one hour cold exposure depends only upon the amplitude of the hypergravic field during the period of cold exposure or whether the response is also dependent on the amplitude and duration of the hypergravic field prior to cold exposure. One hour of cold exposure applied over the last hour of either a 1, 4, 7, 13, 19, 25, or 37 hr period of 3G evoked a decrease in core temperature (T sub c) of about 3 C. However, when rats were subjected concurrently to cold and acceleration following 8 days at 3G, they exhibited a smaller fall in T sub c, suggesting partial recovery of the acceleration induced impairment of temperature regulation. In another series of experiments, the gravitational field profile was changed in amplitude in 3 different ways. Despite the different gravitational field profiles used prior to cold, the magnitude of the fall in T sub c over the 1 hr period of cold exposure was the same in all cases. These results suggest that the thermoregulatory impairment has a rapid onset, is a manifestation of an ongoing effect of hypergravity, and is not dependent upon the prior G profile.

Horowitz, J. M.↗

Effect of α-Tocopherol on the Microscopic Dynamics of Dimyristoylphosphatidylcholine Membrane

Vitamin E behaves as an antioxidant and is well known for its protective properties of the lipid membrane. The most biologically active form of vitamin E in the human organism is α-tocopherol (aToc). Recently (Marquardt, D.; et al. J. Am. Chem. Soc. 2014, 136, 203₋210) it has been shown that aToc resides near the center of dimyristoylphosphatidylcholine (DMPC) bilayer, which is in stark contrast with other PC membranes, where aToc is located near the lipid₋water interface. Here we report an unusual effect of this exceptional location of aToc on the dynamical behavior of DMPC membrane probed by incoherent elastic and quasielastic neutron scattering. For pure DMPC vesicles, elastic scan data show two step-like drops in the elastic intensity at 288 and 297 K, which correspond to the pre- and main phase transitions, respectively. However, inclusion of aToc into DMPC membrane inhibits the step-like elastic intensity drops, indicating a significant impact of aToc on the phase behavior of the membrane. This observation is supported by our differential scanning calorimetry data, which shows that inclusion of aToc leads to a significant broadening of the main phase transition peak, whereas the peak corresponding to the pretransition disappears. We have performed quasielastic neutron scattering (QENS) measurements on DMPC vesicles with various concentrations of aToc at 280, 293, and 310 K. We have found that aToc affects both the lateral diffusion and the internal motions of the lipid molecules. Below the main phase transition temperature inclusion of aToc accelerates both the lateral and the internal lipid motions. On the other hand, above the main phase transition temperature the addition of aToc restricts only the internal motion, without a significant influence on the lateral motion. To conclude, our results support the finding that the location of aToc in DMPC membrane is deep within the bilayer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The mechanism of accelerated phase formation of MgB{sub 2} by Cu-doping during low-temperature sintering

Thermal analysis, phase identification and microstructure observation were adopted to explore the accelerating sintering effect of Cu-doping on the low-temperature formation of MgB{sub 2} below Mg melting. It is found that the Cu-doping sintering of MgB{sub 2} bulk followed an activated sintering mechanism and thus obviously promoted the reaction between Mg and B forming bulk MgB{sub 2}. Accordingly, dense MgB{sub 2} bulks with excellent T{sub c} and J{sub c} were successfully synthesized by the Cu-doping sintering at 575 deg. C for only 5 h. Further, a sintering model was proposed to illuminate the Cu-doping activated sintering mechanism. It is found that during the Cu-doping activated sintering process, the local Mg-Cu liquid generates firstly and then segregates to the interface between Mg and B particles, which can wet Mg particles and provide a rapid transport for the diffusion of neighboring Mg atoms into B particles resulting in the accelerated formation of MgB{sub 2} phase.

36 MATERIALS SCIENCE↗

High temperature polymer degradation: Rapid IR flow-through method for volatile quantification

Accelerated aging of polymers at elevated temperatures often involves the generation of volatiles. These can be formed as the products of oxidative degradation reactions or intrinsic pyrolytic decomposition as part of polymer scission reactions. A simple analytical method for the quantification of water, CO 2 , and CO as fundamental signatures of degradation kinetics is required. Here, we describe an analytical framework and develops a rapid mid-IR based gas analysis methodology to quantify volatiles that are contained in small ampoules after aging exposures. The approach requires identification of unique spectral signatures, systematic calibration with known concentrations of volatiles, and a rapid acquisition FTIR spectrometer for time resolved successive spectra. Furthermore, the volatiles are flushed out from the ampoule with dry N2 carrier gas and are then quantified through spectral and time integration. This method is sufficiently sensitive to determine absolute yields of ~50 μg water or CO 2 , which relates to probing mass losses of less than 0.01% for a 1 g sample, i.e. the early stages in the degradation process. Such quantitative gas analysis is not easily achieved with other approaches. Our approach opens up the possibility of quantitative monitoring of volatile evolution as an avenue to explore polymer degradation kinetics and its dependence on time and temperature.

36 MATERIALS SCIENCE↗

Modeling a Nb3Sn Cryounit in GPT at UITF

Nb₃Sn is a prospective material for future superconducting RF (SRF) accelerator cavities. The material can achieve higher quality factors, higher temperature operation and potentially higher accelerating gradients (E_{acc} 96 MV/m) compared to conventional niobium. In this work, we performed modeling of the Upgraded Injector Test Facility (UITF) at Jefferson Lab utilizing newly constructed Nb₃Sn cavities. We studied the effects of the buncher cavity and varied the gun voltages from 200-500 keV. We have calibrated and optimized the SRF cavity gradients and phases for the Nb₃Sn five-cell cavities energy gains with the framework of General Particle Tracer (GPT). Our calculations show the beam goes cleanly through the unit. There is full energy gain out of the second SRF cavity but not from the first SRF cavity due to non-relativistic phase shifts.

Pokharel, S.↗

A numerical evaluation of the ambient air temperature in the Electron-Ion Collider tunnel

The Electron-Ion Collider (EIC) is a next-generation collider-accelerator that may require consistent operating temperature conditions for the beams within the accelerator tunnels to maintain stable operation. Variations in ambient temperature within the tunnel can cause thermal expansion of beampipe and component supports and can negatively affect the tunnel equipment, impacting the stability of the beamline. Modifications will be made to the Relativistic Heavy Ion Collider (RHIC) at Brookhaven National Laboratory (BNL) to create the EIC, which necessitates a temperature model that addresses these modifications. To approach this problem, the consistency of temperature changes in different tunnel sections was first evaluated by plotting RHIC tunnel temperature data at various times of the day and year. From this data, a tunnel section was selected and a 2D temperature model was created for RHIC, EIC, and EIC with added cooling configurations. Soil temperature data was analyzed to determine the maximum, average, and mode soil temperatures, which were used as boundary conditions in different temperature scenarios. Computational fluid dynamics modeling was used to create 2D temperature profiles for the configurations. From this model, the predicted temperatures indicate that further analysis is required to validate the boundary conditions and benchmark the current conditions to allow the prediction of the tunnel ambient conditions at EIC. This research can be used as a preliminary model to create an EIC tunnel cooling system that will increase the operational stability of the EIC. As a result of my work this summer, I have become familiar with computational fluid dynamics, including creating fluid dynamic simulations using ANSYS Fluent and related software. I have also learned about the project process required for planning large-scale engineering projects.

43 PARTICLE ACCELERATORS↗

Integrated EM & Thermal Simulations with Upgraded VORPAL Software

Nuclear physics accelerators are powered by microwaves which must travel in waveguides between room-temperature sources and the cryogenic accelerator structures. The ohmic heat load from the microwaves is affected by the temperature-dependent surface resistance and in turn affects the cryogenic thermal conduction problem. Integrated EM & thermal analysis of this difficult non-linear problem is now possible with the VORPAL finite-difference time-domain simulation tool. We highlight thermal benchmarking work with a complex HOM feed-through geometry, done in collaboration with researchers at the Thomas Jefferson National Accelerator Laboratory, and discuss upcoming design studies with this emerging tool. This work is part of an effort to generalize the VORPAL framework to include generalized PDE capabilities, for wider multi-physics capabilities in the accelerator, vacuum electronics, plasma processing and fusion R&D fields, and we will also discuss user interface and algorithmic upgrades which facilitate this emerging multiphysics capability.

43 PARTICLE ACCELERATORS↗