Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface cracks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Influence of High Cycle Thermal Loads on Thermal Fatigue Behavior of Thick Thermal Barrier Coatings

Thick thermal barrier coating systems in a diesel engine experience severe thermal Low Cycle Fatigue (LCF) and High Cycle Fatigue (HCF) during engine operation. In the present study, the mechanisms of fatigue crack initiation and propagation, as well as of coating failure, under thermal loads which simulate engine conditions, are investigated using a high power CO2 laser. In general, surface vertical cracks initiate early and grow continuously under LCF and HCF cyclic stresses. It is found that in the absence of interfacial oxidation, the failure associated with LCF is closely related to coating sintering and creep at high temperatures, which induce tensile stresses in the coating after cooling. Experiments show that the HCF cycles are very damaging to the coating systems. The combined LCF and HCF tests produced more severe coating surface cracking, microspallation and accelerated crack growth, as compared to the pure LCF test. It is suggested that the HCF component cannot only accelerate the surface crack initiation, but also interact with the LCF by contributing to the crack growth at high temperatures. The increased LCF stress intensity at the crack tip due to the HCF component enhances the subsequent LCF crack growth. Conversely, since a faster HCF crack growth rate will be expected with lower effective compressive stresses in the coating, the LCF cycles also facilitate the HCF crack growth at high temperatures by stress relaxation process. A surface wedging model has been proposed to account for the HCF crack growth in the coating system. This mechanism predicts that HCF damage effect increases with increasing temperature swing, the thermal expansion coefficient and the elastic modulus of the ceramic coating, as well as the HCF interacting depth. A good agreement has been found between the analysis and experimental evidence.

Zhu, Dongming↗
NASA NTRS2008

Replica-Based Crack Inspection

Surface replication has been proposed as a method for crack detection in space shuttle main engine flowliner slots. The results of a feasibility study show that examination of surface replicas with a scanning electron microscope can result in the detection of cracks as small as 0.005 inch, and surface flaws as small as 0.001 inch, for the flowliner material.

Newman, John A.↗
NASA NTRS1974

Effects of proof loads and combined mode loadings on fracture and flaw growth characteristics of aerospace alloys

This experimental program was undertaken to determine the effects of (1) combined tensile and bending loadings, (2) combined tensile and shear loadings, and (3) proof overloads on fracture and flaw growth characteristics of aerospace alloys. Tests were performed on four alloys: 2219-T87 aluminum, 5Al-2.5Sn (ELl) titanium, 6Al-4V beta STA titanium and high strength 4340 steel. Tests were conducted in room air, gaseous nitrogen at -200F (144K), liquid nitrogen and liquid hydrogen. Flat center cracked and surface flawed specimens, cracked tube specimens, circumferentially notched round bar and surface flawed cylindrical specimens were tested. The three-dimensional photoelastic technique of stress freezing and slicing was used to determine stress intensity factors for surface flawed cylindrical specimens subjected to tension or torsion. Results showed that proof load/temperature histories used in the tests have a small beneficial effect or no effect on subsequent fracture strength and flaw growth rates.

Shah, R. C.↗
DOE OSTI2020

Influence of acid leaching surface treatment on indentation cracking of soda lime silicate glass

Past work has shown that water or acid soaking treatments can increase the mechanical strength of soda lime silicate (SLS) glasses. In this work, we show that acid leaching treatments result in an increase in the apparent crack resistance of the acid-leached surface of SLS glass during indentation. Vickers indentation tests in controlled environments show a humidity dependence of radial cracking, suggesting that the transport of water through the leached layer plays a critical role in the propagation of cracks to the glass surface. Here, molecular dynamics simulations with reactive force fields indicate that the leached surface layer can undergo pressure-induced mechanochemical reactions during indentation, which increases the bridging oxygen connectivity in the silica network of the leached layer. Such structural changes can hinder transport of water molecules from the environment to the subsurface crack tip. Based on experimental observations and simulation results, a new hypothesis is proposed that mechanochemical restructuring in the leached layer in response to the applied load may lower the transport kinetics of molecular water to critical flaws, resulting in an apparent enhancement in the crack resistance of the acid-leached surface of SLS glass.

36 MATERIALS SCIENCE↗
NASA NTRS1977

Friction, deformation and fracture of single-crystal silicon carbide

Friction experiments were conducted with hemispherical and conical diamond riders sliding on the basal plane of silicon carbide. The results indicate that, when deformation is primarily elastic, the friction does not depend on crystallographic orientation and there is no detectable fracture or cracking. When, however, plastic deformation occurs, silicon carbide exhibits anisotropic friction and deformation behavior. Surface fracture crack patterns surrounding wear tracks are observed to be of three types. The crack-geometries of two types are generally independent of orientation, the third crack, however, depends on the orientation. All surface cracks extend into subsurface. Anisotropic friction, deformation and fracture on the basal plane are primarily controlled by the slip system and cleavage.

Miyoshi, K.↗
NASA NTRS1977

Friction, deformation and fracture of single-crystal silicon carbide

An investigation was conducted to determine the nature of the deformation and fracture of silicon carbide and its effects on friction properties. Friction experiments were conducted with hemispherical and conical diamond riders sliding on the basal plane of silicon carbide. The results indicate that, when deformation is primarily elastic, the friction does not depend on crystallographic orientation and there is no detectable fracture or cracking. When, however, plastic deformation occurs, silicon carbide exhibits anisotropic friction and deformation behavior. Surface fracture crack patterns surrounding wear tracks are observed to be of three types. The crack-geometries of two types are generally independent of orientation, the third crack, however, depends on the orientation. All surface cracks extend into subsurface.

Miyoshi, K.↗
NASA NTRS1973

Fracture analysis of surface- and through-cracked sheets and plates.

The Neuber stress-concentration relation for notches in an elastic-plastic material subjected to shear loading was generalized for a crack in a finite plate subjected to tensile loading. An equation was derived which related the linear elastic stress-intensity factor, the applied stress, and two material parameters. The equation was then used as a two-parameter fracture criterion for surface- and through-cracked specimens. Fracture data from the literature on surface- and through-cracked sheet and plate specimens of steel, titanium alloy, titanium weldment, and aluminum alloy tested at room and cryogenic temperature were analyzed according to the proposed equation. For surface cracks, wide ranges of crack-depth to crack-length ratio and crack-depth to specimen-thickness ratio were considered. For through cracks, wide ranges of crack length and specimen width were also considered.-

Newman, J. C., Jr.↗
NASA NTRS1992

GENSURF: A mesh generator for 3D finite element analysis of surface and corner cracks in finite thickness plates subjected to mode-1 loadings

A computer program that generates three-dimensional (3D) finite element models for cracked 3D solids was written. This computer program, gensurf, uses minimal input data to generate 3D finite element models for isotropic solids with elliptic or part-elliptic cracks. These models can be used with a 3D finite element program called surf3d. This report documents this mesh generator. In this manual the capabilities, limitations, and organization of gensurf are described. The procedures used to develop 3D finite element models and the input for and the output of gensurf are explained. Several examples are included to illustrate the use of this program. Several input data files are included with this manual so that the users can edit these files to conform to their crack configuration and use them with gensurf.

Raju, I. S.↗
DOE OSTI2022

The role of surface forces in environment-enhanced cracking of brittle solids

Fracture initiation and propagation in brittle materials is promoted in surface-reactive (sorptive) environments, a phenomenon known as subcritical crack growth (SCG). Laboratory measured crack-propagation velocity vs. stress intensity factor relationships typically exhibit highly nonlinear, multi-stage characteristics that are sensitive to environmental factors such as adsorbate concentration and temperature. For practical purposes, empirical relationships (e.g., a power law) have been used to describe this complex phenomenon. However, how the overall SCG behavior emerges from the underlying fundamental processes near the crack tip, such as the interaction of the crack surfaces separated by only a few nanometers and mass transport within the nano-confined space, is still not well understood. This paper develops a mechanistic, surface-force-based fracture theory (SFFT) which integrates surface force models, fluid transport models, and linear elastic fracture mechanics to quantitatively explain the multi-stage characteristics of SCG in brittle solids. A numerical model is developed based on SFFT and solved through an implicit partitioned scheme for efficiency and modularity. The results are validated by Wiederhorn's data on crack propagation in soda-lime glasses at a wide range of relative humidity levels. We show that, for the first time, the entire range of an SCG curve can be captured by a single physics-based model. The predicted SCG curves reveal that the development of repulsive disjoining pressure behind the crack tip can be responsible for the reduced apparent fracture toughness in a sorptive environment. In conclusion, the shape of the SCG curve, and its changes with respect to the environment, is found to critically depend on the assumed transport models.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Robust Solar Receivers Using MAX Phase Materials

This work was supported by the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy under the Solar Energy Technologies Office Award Number 35928. The objective of the proposed effort was to develop and optimize additive manufacturing technologies for low-cost fabrication of high-temperature receivers using MAX phase-based materials (Ti 3 SiC 2 and Ti 3 AlC 2 ). MAX phase materials are a group of ternary metal carbides and nitrides where M stands for an early transition metal element, A is a group 13–16 element, and X is C and/or N. In Phase 1, the binder jetting additive manufacturing process was used to synthesize and characterize the Ti 3 SiC 2 MAX phase material. The typical process involved first producing a TiC preform using binder jetting followed by infiltration of the preform with silicon melt to form Ti 3 SiC 2 in situ. The reaction-infiltrated samples showed formation of MAX phase in the sample core; however, the surface showed cracking. Various process conditions—cooling rates, hold times, Si proportion, etc.—were varied to minimize the surface cracking. The fabricated MAX phase core was characterized by microstructure analysis and evaluations of mechanical properties such as hardness and thermal shock. In Phase 2, the focus included fabrication of Ti 3 SiC 2 MAX phase materials by spark plasma sintering (SPS) and synthesis of Ti 3 AlC 2 MAX phase materials by the Al melt infiltration process. It is expected that Al infiltration will not cause sample cracking, since Al does not expand during solidification. In addition, other processing approaches were investigated to fabricate the MAX phase materials, such as SPS with a graphite bedding approach for producing short-length Ti 3 AlC 2 MAX phase tubes for demonstration of prototypical Concentrating Solar Power receiver tubes. Fabricated samples underwent thermo-mechanical testing to validate the materials for the solar receiver application at temperatures >1000°C. In Phase 3, the effort focused on the development and optimization of the Ti-Al-C MAX phase composite material using the Al melt infiltration approach. We started with optimization of precursor powders and making preform structures by either pressing them in a die or using the binder jetting additive manufacturing process followed by Al melt infiltration. In addition, we investigated the formation of preform structures by cold isostatic pressing followed by Al melt infiltration for making Ti-Al-C MAX phase composite. Thermo-mechanical characterizations, such as creep, strength, and thermal shock, were conducted to establish the structures’ performance.

36 MATERIALS SCIENCE↗
NASA NTRS1994

Thermomechanical Fatigue Damage/Failure Mechanisms in SCS-6/Timetal 21S [0/90](Sub S) Composite

The thermomechanical fatigue (TMF) deformation, damage, and life behaviors of SCS6/Timetal 21S (0/90)s were investigated under zero-tension conditions. In-phase (IP) and out-of-phase (OP) loadings were investigated with a temperature cycle from 150 to 650 deg C. An advanced TMF test technique was used to quantify mechanically damage progression. The technique incorporated explicit measurements of the macroscopic (1) isothermal static moduli at the temperature extremes of the TMF cycle and (2) coefficient of thermal expansion (CTE) as functions of the TMF cycles. The importance of thermal property degradation and its relevance to accurate post-test data analysis and interpretation is briefly addressed. Extensive fractography and metallography were conducted on specimens from failed and interrupted tests to characterize the extent of damage at the microstructure level. Fatigue life results indicated trends analogous to those established for similar unidirectional(0) reinforced titanium matrix composite systems. High stress IP and mid to low stress OP loading conditions were life-limiting in comparison to maximum temperature isothermal conditions. Dominant damage mechanisms changed with cycle type. Damage resulting from IP TMF conditions produced measurable decreases in static moduli but only minimal changes in the CTE. Metallography on interrupted and failed specimens revealed extensive (0) fiber cracking with sparse matrix damage. No surface initiated matrix cracks were present. Comparable OP TMF conditions initiated environment enhanced surface cracking and matrix cracking initiated at (90) fiber/matrix (F/M) interfaces. Notable static moduli and CTE degradations were measured. Fractography and metallography revealed that the transverse cracks originating from the surface and (90) F/M interfaces tended to converge and coalesce at the (0) fibers.

Castelli, Michael G.↗
NASA NTRS1985

Detecting Cracks in Rough Metal Surfaces

Test based on eddy-current probe technique identifies cracks in swaged metals. Hinged collar with spring-loaded latch holds probe in place on part tested. For repeated measurements on same or similar parts, collar loosened and moved to various measuring positions. Method suitable for many kinds of metal parts, including swaged fittings, tubing, and pipes. Used for rapid crack/no-crack determinations in suspect parts already installed.

Zuver, N. T.↗
NASA NTRS2007

Replica-based Crack Inspection

A surface replica-based crack inspection method has recently been developed for use in Space Shuttle main engine (SSME) hydrogen feedline flowliners. These flowliners exist to ensure favorable flow of liquid hydrogen over gimble joint bellows, and consist of two rings each containing 38 elongated slots. In the summer of 2002, multiple cracks ranging from 0.1 inches to 0.6 inches long were discovered; each orbiter contained at least one cracked flowliner. These long cracks were repaired and eddy current inspections ensured that no cracks longer than 0.075 inches were present. However, subsequent fracture-mechanics review of flight rationale required detection of smaller cracks, and was the driving force for development of higher-resolution inspection method. Acetate tape surface replicas have been used for decades to detect and monitor small cracks. However, acetate tape replicas have primarily been limited to laboratory specimens because complexities involved in making these replicas - requiring acetate tape to be dissolved with acetone - are not well suited for a crack inspection tool. More recently developed silicon-based replicas are better suited for use as a crack detection tool. A commercially available silicon-based replica product has been determined to be acceptable for use in SSME hydrogen feedlines. A method has been developed using this product and a scanning electron microscope for analysis, which can find cracks as small as 0.005 inches and other features (e.g., pits, scratches, tool marks, etc.) as small as 0.001 inches. The resolution of this method has been validated with dozens of cracks generated in a laboratory setting and this method has been used to locate 55 cracks (ranging in size from 0.040 inches to 0.004 inches) on space flight hardware. These cracks were removed by polishing away the cracked material and a second round of replicas confirmed the repair.

Newman, John A.↗
NASA NTRS2015

Experimental and Finite Element Modeling of Near-Threshold Fatigue Crack Growth for the K-Decreasing Test Method

The experimental methods to determine near-threshold fatigue crack growth rate data are prescribed in ASTM standard E647. To produce near-threshold data at a constant stress ratio (R), the applied stress-intensity factor (K) is decreased as the crack grows based on a specified K-gradient. Consequently, as the fatigue crack growth rate threshold is approached and the crack tip opening displacement decreases, remote crack wake contact may occur due to the plastically deformed crack wake surfaces and shield the growing crack tip resulting in a reduced crack tip driving force and non-representative crack growth rate data. If such data are used to life a component, the evaluation could yield highly non-conservative predictions. Although this anomalous behavior has been shown to be affected by K-gradient, starting K level, residual stresses, environmental assisted cracking, specimen geometry, and material type, the specifications within the standard to avoid this effect are limited to a maximum fatigue crack growth rate and a suggestion for the K-gradient value. This paper provides parallel experimental and computational simulations for the K-decreasing method for two materials (an aluminum alloy, AA 2024-T3 and a titanium alloy, Ti 6-2-2-2-2) to aid in establishing clear understanding of appropriate testing requirements. These simulations investigate the effect of K-gradient, the maximum value of stress-intensity factor applied, and material type. A material independent term is developed to guide in the selection of appropriate test conditions for most engineering alloys. With the use of such a term, near-threshold fatigue crack growth rate tests can be performed at accelerated rates, near-threshold data can be acquired in days instead of weeks without having to establish testing criteria through trial and error, and these data can be acquired for most engineering materials, even those that are produced in relatively small product forms.

Smith, Stephen W.↗
NASA NTRS1975

Crack-closure and crack-growth measurements in surface-flawed titanium alloy Ti6Al-4V

The crack-closure and crack-growth characteristics of the titanium alloy Ti-6Al-4V were determined experimentally on surface-flawed plate specimens. Under cyclic loading from zero to tension, cracks deeper than 1 mm opened at approximately 50 percent of the maximum load. Cracks shallower than 1 mm opened at higher loads. The correlation between crack-growth rate and the total stress-intensity range showed a lower threshold behavior. This behavior was attributed to the high crack-opening loads at short cracks because the lower threshold was much less evident in correlations between the crack-growth rates and the effective stress-intensity range.

Elber, W.↗