Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface area”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Control of volume resistivity in inorganic-organic separators

Control of resistivity in NASA inorganic-organic separators is achieved by incorporating small percentages of high surface area, fine-particle silica with other ingredients in the separator coating. The volume resistivity appears to be predictable from coating composition, that is, from the surface area of filler particles in the coating. The approach has been applied to two polymer-'plasticizer'-filler coating systems, where the filler content of each is below the generally acknowledged critical pigment volume concentration of the coating. Application of these coating systems to 0.0254 cm thick (10 mil) fuel-cell grade asbestos sheet produces inexpensive, flexible, microporous separators that perform at least as well as the original inorganic-organic concept, the Astropower separator.

Sheibley, D. W.↗
NASA NTRS1995

Latitudinal distribution of black carbon soot in the upper troposphere and lower stratosphere

Black carbon soot from the upper troposphere and lower stratosphere has been systematically collected at latitudes from 90 deg N to 45 deg S. The measured latitudinal distribution of this soot at 10 to 11 km altitude is found to covary with commercial air traffic fuel use, suggesting that aircraft fuel combustion at altitude is the principal source. In addition, at latitudes where the commercial air traffic is high, measured black carbon soot values are high even at 20 km altitude, suggesting that aircraft-generated soot injected just above the tropopause may be transported to higher altitudes. During the volcanically influenced period in which these samples were collected, the number abundances, total mass, and calculated total surface area of black carbon soot are 2-3 orders of magnitude lower than similar measures of sulfuric acid aerosol. During volcanically quiescent periods, the calculated total surface area of black carbon soot aerosol is of the same order of magnitude as that of the background sulfuric acid aerosol. It appears from this comparison that black carbon soot is only capable of influencing lower stratosphere or upper troposphere chemistry during periods when the aerosol budget is not dominated by volcanic activity. It remains to determine the extent to which black carbon soot particles act as nuclei for sulfuric acid aerosol formation. However, mass balance calculations suggest that aircraft soot injected at altitude does not represent a significant source of condensation nuclei for sulfuric acid aerosols.

Blake, David F.↗
NASA NTRS1995

A Model Simulation of Pinatubo Volcanic Aerosols in the Stratosphere

A one-dimensional, time-dependent model is used to study the chemical, microphysical, and radiative properties of volcanic aerosols produced by the Mount Pinatubo eruption on June 15, 1991. Our model treats gas-phase sulfur photochemistry, gas-to-particle conversion of sulfur, and the microphysics of sulfate aerosols and ash particles under stratospheric conditions. The dilution and diffusion of the volcanic eruption clouds are also accounted for in these conditions. Heteromolecular homogeneous and heterogeneous binary H2SO4/H2O nucleation, acid and water condensational growth, coagulation, and gravitational sedimentation are treated in detail in the model. Simulations suggested that after several weeks, the volcanic cloud was composed mainly of sulfuric acid/water droplets produced in situ from the SO2 emissions. The large amounts of SO2 (around 20 Mt) injected into the stratosphere by the Pinatubo eruption initiated homogeneous nucleation which generated a high concentration of small H2SO4/H2O droplets. These newly formed particles grew rapidly by condensation and coagulation in the first few months and then reach their stabilized sizes with effective radii in a range between 0.3 and 0.5 micron approximately one-half year after the eruption. The predicted volcanic cloud parameters reasonably agree with measurements in term of the vertical distribution and lifetime of the volcanic aerosols, their basic microphysical structures (e.g., size distribution, concentration, mass ratio, and surface area) and radiative properties. The persistent volcanic aerosols can produce significant anomalies in the radiation field, which have important climatic consequences. The large enhancement in aerosol surface area can result in measurable global stratospheric ozone depletion.

Zhao , Jing-xia↗
DOE OSTI2022

Construction of Fluorine- and Piperazine-Engineered Covalent Triazine Frameworks Towards Enhanced Dual-Ion Positive Electrode Performance

Organic positive electrodes featuring lightweight, and tunable energy storage modes by molecular structure engineering have promising application prospects in dual-ion batteries. Herein, a series of highly porous covalent triazine frameworks (CTFs) were synthesized under ionothermal conditions using fluorinated aromatic nitrile monomers containing a piperazine ring. Fluorinated monomers can result in more defects in CTFs, leading to a higher surface area up to 2515 m 2 /g and a higher N content of 11.34 wt% compared to the products from the non-fluorinated monomer. The high surface area and abundant redox sites of these CTFs afforded high specific capacities (up to 279 mAh/g at 0.1 A/g), excellent rate performance (89 mAh/g at 5 A/g), and durable cycling performance (92.3% retention rate after 500 cycles at 2.0 A g -1 ) as dual-ion positive electrodes

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Effects of chemical composition and physicochemical properties of poplar biomass on the performance of 3D printed poplar-reinforced PLA materials

Lignocellulosic biomass has been well-acknowledged as a filler for making 3D printed composites. The technical performances of composites were influenced by the characteristics of the components. The correlations between poplar biomass properties and the mechanical and thermal performances of the 3D printed poplar-plastic composites were investigated. The characteristics of poplar were modified by different pretreatment methods, including using hot water, dilute acid, and organic solvent (organosolv), and each treated poplar biomass was applied as a filler in a polylactic acid (PLA) polymer matrix to produce eco-friendly materials. These solvent pretreatments increased the hydrophobicity and surface area of poplar. Organosolv treated poplar showed the highest cellulose content and significantly increased Young's modulus of its biocomposites. Principal component analysis revealed that the specific surface area and water contact angle of biomass contributed to the thermal stability of biocomposites. Additionally, the degree of polymerization of cellulose and xylan content within the biomass correlated with the biocomposites' break stress. Notably, the crystallinity of biocomposites impacted the modulus of these materials. The reported relationships between biomass characteristics and 3D printed composite behaviors provide guidance for optimizing biomass processing in biocomposite applications.

Ji, Anqi [State Univ. of New York (SUNY), Syracuse↗
DOE OSTI2024

Cellulose regulated lignin/cellulose-based carbon materials with hierarchical porous structure for energy storage

Lignin has gained extensive attention as an ideal carbon precursor due to its abundance and high carbon content. However, the agglomeration of lignin and additional corrosive and unrecyclable reagents in direct pyrolysis still limit the development of lignin-based porous carbons. Herein, a facile and eco-friendly strategy was proposed to fabricate hierarchical porous lignin/cellulose-based carbon materials (LCs). In the process, cellulose nanofibrils acted as the skeleton of the bio-aerogels, which supported lignin and benefit the preparation of the LCs. Moreover, the specific surface area and the graphitization degree of LCs can be regulated by varying the cellulose content. Without activation, the bio-based carbon material (LC30) had a high specific surface area of 1770 m 2 g –1 , which displayed high specific capacitance of 216.2 F g –1 at the current density of 0.5 A g –1 . The supercapacitor based on LC30 also showed outstanding energy density of 12.3 Wh kg –1 at the power density of 50 W kg –1 . The sustainable raw material, simple and harmless preparation process, and remarkable electrochemical performance enable LC30, a promising supercapacitor electrode for energy storage.

25 ENERGY STORAGE↗
DOE OSTI2024

The Role of Lignin Molecular Weight on Activated Carbon Pore Structure

Over the past decade, the production of biofuels from lignocellulosic biomass has steadily increased to offset the use of fuels from petroleum. To make biofuels cost-competitive, however, it is necessary to add value to the “ligno-” components (up to 30% by mass) of the biomass. The properties of lignin, in terms of molecular weight (MW), chemical functionality, and mineral impurities often vary from biomass source and biorefinery process, resulting in a challenging precursor for product development. Activated carbon (AC) is a feasible target for the lignin-rich byproduct streams because it can be made from nearly any biomass, and it has a market capacity large enough to use much of the lignin generated from the biorefineries. However, it is not known how the variability in the lignin affects the key properties of AC, because, until now, they could not be well controlled. In this work, various fractions of ultraclean (<0.6% ash) lignin are created with refined MW distributions using Aqueous Lignin Purification using Hot Agents (ALPHA) and used as precursors for AC. AC is synthesized via zinc chloride activation and characterized for pore structure and adsorption capacity. We show that AC surface area and the adsorption capacity increase when using lignin with increasing MW, and, furthermore, that reducing the mineral content of lignin can significantly enhance the AC properties. The surface area of the AC from the highest MW lignin can reach ~1830 m2/g (absorption capacity). Furthermore, single step activation carbonization using zinc chloride allows for minimal carbon burn off (<30%), capturing most of the lignin carbon compared to traditional burn off methods in biorefineries for heat generation.

Biochemistry & Molecular Biology↗
NASA NTRS1994

Ozone response to enhanced heterogeneous processing after the eruption of Mt. Pinatubo

Increases in aerosol loading after the Pinatubo eruption are expected to cause additional ozone depletion. Even though aerosol loadings were highest in the winter of 1991-1992, recent analyses of satellite and ground-based ozone measurements indicate that ozone levels in the winter of 1992-1993 are the lowest recorded in recent years, raising the question of the mechanisms responsible for such behavior. We have incorporated aerosol surface areas derived from the Stratospheric Aerosol and Gas Experiment II (SAGE-II) measurements into our two-dimensional model. Inclusion of heterogeneous chemsitry on these enhanced aerosol surfaces yields maximum ozone reductions during the winter of 1992-1993 in the Northern Hemisphere, consistent with those derived from observations. This delayed behavior is due to the combination of the non-linear nature of the impact of heterogeneous reactions as a function of aerosol surface area, and the long time constants for ozone in the lower stratosphere. If heterogeneous mechanisms are primarily responsible for the low 1992-1993 ozone levels, we expect ozone concentrations to start recovering in 1994.

Rodriguez, Jose M.↗
DOE OSTI2020

Zinc-iodine secondary energy storage methods, devices, and electrolytes

Disclosed are cathodes having electron-conductive high-surface-area materials, aqueous non-halide-containing electrolytes, secondary zinc-iodine energy storage devices using the same, and methods for assembling the same. The disclosed high-surface-area materials and the aqueous non-halide-containing electrolyte solutions can contribute together to the confinement of the active iodine species in the cathode and to the minimization of shuttle effects and self-discharging. The non-halide-containing electrolyte salts can facilitate preferential adsorption of the iodine species to the cathode material rather than dissolution in the aqueous electrolyte solution, thereby contributing to the confinement of the active iodine species.

25 ENERGY STORAGE↗
NASA NTRS2004

Homoepitaxial and Heteroepitaxial Growth on Step-Free SiC Mesas

This article describes the initial discovery and development of new approaches to SiC homoepitaxial and heteroepitaxial growth. These approaches are based upon the previously unanticipated ability to effectively supress two-dimensional nucleation of 3C-SiC on large basal plane terraces that form between growth steps when epitaxy is carried out on 4H- and 6H-SiC nearly on-axis substrates. After subdividing the growth surface into mesa regions, pure stepflow homoeptixay with no terrace nucleation was then used to grow all existing surface steps off the edges of screw-dislocation-free mesas, leaving behind perfectly on-axis (0001) basal plane mesa surfaces completely free of atomic-scale steps. Step-free mesa surfaces as large as 0.4 mm x 0.4 mm were experimentally realized, with the yield and size of step-free mesas being initally limited by substrate screw dislocations. Continued epitaxial growth following step-free surface formation leads to the formation of thin lateral cantilevers that extend the step-free surface area from the top edge of the mesa sidewalls. By selecting a proper pre-growth mesa shape and crystallographic orientation, the rate of cantilever growth can be greatly enhanced in a web growth process that has been used to (1) enlarge step-free surface areas and (2) overgrow and laterally relocate micropipes and screw dislocations. A new growth process, named step-free surface heteroepitaxy, has been developed to achieve 3C-SiC films on 4H- and 6H-SiC substrate mesas completely free of double positioning boundary and stacking fault defects. The process is based upon the controlled terrace nucleation and lateral expansion of a single island of 3C-SiC across a step-free mesa surface. Experimental results indicate that substrateepilayer lattice mismatch is at least partially relieved parallel to the interface without dislocations that undesirably thread through the thickness of the epilayer. These results should enable realization of improved SiC homojunction and heterojunction devices. In addition, these experiments offer important insights into the nature of polytypism during SiC crystal growth.

Neudeck, Philip G.↗
NASA NTRS1988

Space plasma contactor research, 1987

A simple model describing the process of electron collection from a low pressure ambient plasma in the absence of magnetic field and contactor velocity effects is presented. Experimental measurments of the plasma surrounding the contactor are used to demonstrate that a double-sheath generally develops and separates the ambient plasma from a higher density, anode plasma located adjacent to the contactor. Agreement between the predictions of the model and experimental measurements obtained at the electron collection current levels ranging to 1 A suggests the surface area at the ambient plasma boundary of the double-sheath is equal to the electron current being collected divided by the ambient plasma random electron current density; the surface area of the higher density anode plasma boundary of the double-sheath is equal to the ion current being emitted across this boundary divided by the ion current density required to sustain a stable sheath; and the voltage drop across the sheath is determined by the requirement that the ion and electron currents counterflowing across the boundaries be at space-charge limited levels. The efficiency of contactor operation is shown to improve when significant ionization and excitation is induced by electrons that stream from the ambient plasma through the double-sheath and collide with neutral atoms being supplied through the hollow cathode.

Wilbur, Paul J.↗
NASA NTRS1993

High temperature co-axial winding transformers

The analysis and design of co-axial winding transformers is presented. The design equations are derived and the different design approaches are discussed. One of the most important features of co-axial winding transformers is the fact that the leakage inductance is well controlled and can be made low. This is not the case in conventional winding transformers. In addition, the power density of co-axial winding transformers is higher than conventional ones. Hence, using co-axial winding transformers in a certain converter topology improves the power density of the converter. The design methodology used in meeting the proposed specifications of the co-axial winding transformer specifications are presented and discussed. The final transformer design was constructed in the lab. Co-axial winding transformers proved to be a good choice for high power density and high frequency applications. They have a more predictable performance compared with conventional transformers. In addition, the leakage inductance of the transformer can be controlled easily to suit a specific application. For space applications, one major concern is the extraction of heat from power apparatus to prevent excessive heating and hence damaging of these units. Because of the vacuum environment, the only way to extract heat is by using a cold plate. One advantage of co-axial winding transformers is that the surface area available to extract heat from is very large compared to conventional transformers. This stems from the unique structure of the co-axial transformer where the whole core surface area is exposed and can be utilized for cooling effectively. This is a crucial issue here since most of the losses are core losses.

Divan, Deepakraj M.↗
NASA NTRS1994

Two-dimensional simulation of Pinatubo aerosol and its effect on stratospheric ozone

This paper presents time-dependent simulations of the response of the stratosphere to the injection into the atmosphere of massive amounts of sulfur during the eruption of Mt. Pinatubo (The Philippines) in June 1991. The study is based on a coupled two-dimensional chemical-dynamical-radiative model to which a microphysical model for sulfate aerosol formation and fate has been added. The study suggests that, during the first year (July 1991 to June 1992) following the volcanic eruption, the observed changes in the ozone amount integrated between 65 deg S and 65 deg N were caused primarily by changes in the meridional circulation (associated with heating by the volcanic cloud in the tropics) and in the photolysis rate of molecules such as ozone (associated with backscattering of light by the cloud). During the second year after the eruption, as the aerosol was dispersed at all latitudes and, in particular, reached the polar region, the largest contribution to ozone reduction resulted from the heterogeneous chemical conversion of N2O5 and ClONO2 on the surface of the aerosol particles. The conversion of the latter compound, and hence the magnitude of the calculated ozone depletion, is highly dependent on the temperature in the lower stratosphere. Despite the fact that the surface area provided by aerosol particles decreased during the second year following the eruption, the calculated ozone depletion remained significant because the conversion of N2O5 is insensitive to the aerosol surface area density for values larger than 1-10 sq microns/cu cm (depending on latitude). The predicted reduction in ozone at 20 km in March during the third year (July 1993 to June 1994) of the model integration is smaller by a factor of 2 than it was during the second year.

Tie, Xuexi↗
NASA NTRS2003

Ceramic Spheres From Cation Exchange Beads

Porous ZrO2 and hollow TiO2 spheres were synthesized from a strong acid cation exchange resin. Spherical cation exchange beads, polystyrene based polymer, were used as a morphological-directing template. Aqueous ion exchange reaction was used to chemically bind (ZrO)(2+) ions to the polystyrene structure. The pyrolysis of the polystyrene at 600 C produces porous ZrO2 spheres with a surface area of 24 sq m/g with a mean sphere size of 42 microns. Hollow TiO2 spheres were synthesized by using the beads as a micro-reactor. A direct surface reaction - between titanium isopropoxide and the resin beads forms a hydrous TiO2 shell around the polystyrene core. The pyrolysis of the polystyrene core at 600 C produces hollow anatase spheres with a surface area of 42 sq m/g with a mean sphere size of 38 microns. The formation of ceramic spheres was studied by XRD, SEM and B.E.T. nitrogen adsorption measurements.

Dynys, F. W.↗
NASA NTRS1974

Micrometeoroid abrasion of lunar rocks - A Monte Carlo simulation

A Monte Carlo computer model simulating the randomness of the impact process both in space and in time is developed in order to provide insight into lunar rock erosion by single particle abrasion and into bombardment history of fractional surface areas of lunar rocks. Microcrater frequencies derived from lunar rocks are used to calculate magnitude and probability of each cratering event, and experimental cratering results are employed to determine the eroded volumina for individual crater sizes. It is shown that a fractional surface area of a lunar rock sample may have a completely different bombardment history, and that the exposure histories and actual erosion depths of the surfaces vary accordingly and are highly heterogeneous. A minimum erosion rate of 0.3 to 0.6 mm for the past one million years is obtained.

Hoerz, F.↗
NASA NTRS1986

Houseplants, Indoor Air Pollutants, and Allergic Reactions

The technology of using houseplant leaves for reducing volatile organics inside closed facilities has been demonstrated with formaldehyde and benzene. Philodendrons are among the most effective plants tested to date. Philodendron domesticum had demonstrated the ability to remove formaldehyde from small experimental chambers at a rate of 4.31 micro-g/sq cm leaf surface area with initial starting concentrations of 22 ppm. At initial starting concentrations of 2.3 ppm a formaldehyde removal rate of 0.57 micro-g/sq cm was achieved during a 24 hour test. Aleo vera demonstrated a much higher formaldehyde efficiency removal rate than Philodendron domesticum at low formaldehyde concentrations. During a 24 hour exposure period 5 ppm of formaldehyde were reduced to 0.5 ppm demonstrating a removal efficiency rate of 3.27 micro-g/sq cm. Removal efficiency rates can be expected to decrease with concentration levels because fewer molecules of chemicals come in contact with the leaf surface area. Several centimeters of small washed gravel should be used to cover the surface of pot plants when large numbers of plants are kept in the home. The reason for this is to reduce the exposed area of damp potting soil which encourages the growth of molds (fungi). The leaves of Philodendron domesticum and golden pothos (Scindapsus aureus) have also demonstrated their ability to remove benzene and carbon monoxide from closed chambers. A combination of activated carbon and plant roots have demonstrated the greatest potential for removing large volumes of volatile organics along with smoke and possible radon from closed systems. Although fewer plants are required for this concept a mechanical blower motor must be used to pull or push the air through the carbon-root filter. NASA studies on motor sizes and bioregeneration rates should be completed by 1988.

Wolverton, B. C.↗
DOE OSTI2025

Rigid Supramolecular Aramid Nanotubes as Catalyst Supports

Solution‐phase heterogeneous catalysts benefit from nanoscale dimensions, which maximize specific surface area and enhance catalytic activity. However, the ease of recovering such nanocatalysts depends on the design of the support materials, which are often particle‐like. Rigid 1D nanomaterials are proposed as supports that can enhance separability while offering high volumetric specific surface area for greater catalyst loading and activity. Here, aramid amphiphiles (AAs) are designed to spontaneously self‐assemble in water into high‐aspect‐ratio supramolecular nanotubes with tunable surface chemistry. These AA nanotubes exhibit high persistence lengths (P = 750 ± 340 µm) and mechanical stiffnesses (3 N/m). Incorporating surface thiol groups enables immobilization of catalytic gold nanoparticles. The resulting AA nanotube‐gold nanoparticle complexes exhibit high catalytic activity, efficient recoverability via simple microfiltration, and sustained reusability over ten reaction cycles. This study demonstrates the utility of molecular self‐assembled 1D nanomaterials as versatile scaffolds for the reuse and recovery of nanoscale catalysts.

1D nanomaterials↗