Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “stiffness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Development of procedures for calculating stiffness and damping of elastomers in engineering applications, part 6

An elastomer damper was designed, tested, and compared with the performance of a hydraulic damper for a power transmission shaft. The six button Viton-70 damper was designed so that the elastomer damper or the hydraulic damper could be activated without upsetting the imbalance condition of the assembly. This permitted a direct comparison of damper effectiveness. The elastomer damper consistently performed better than the hydraulic mount and permitted stable operation of the power transmission shaft to speeds higher than obtained with the squeeze film damper. Tests were performed on shear specimens of Viton-79, Buna-N, EPDM, and Neoprene to determine performance limitations imposed by strain, temperature, and frequency. Frequencies of between 110 Hz and 1100 Hz were surveyed with imposed strains between 0.0005 and 0.08 at temperatures of 32 C, 66 C, and 80 C. A set of design curves was generated in a unified format for each of the elastomer materials.

Rieger, A.↗
NASA NTRS1980

Development of procedures for calculating stiffness and damping of elastomers in engineering applications, part 7

An elastomer shear damper was designed, tested, and compared with the performance of the T 55 power turbine supported on the production engine roller bearing support. The Viton 70 shear damper was designed so that the elastomer damper could be interchanged with the production T 55 power turbine roller bearing support. The results show that the elastomer sheer dampener permitted stable operation of the power turbine to the maximum operating speed of 16,000 rpm.

Rieger, A.↗
NASA NTRS1982

Aerodynamic stiffness of an unbound eccentric whirling centrifugal impeller with an infinite number of blades

An unbounded eccentric centrifugal impeller with an infinite number of log spiral blades undergoing synchronous whirling in an incompressible fluid is considered. The forces acting on it due to coriolis forces, centripetal forces, changes in linear momentum, changes in pressure due to rotating and changes in pressure due to changes in linear momentum are evaluated.

Allaire, P. E.↗
NASA NTRS1983

Identification and management of filament-wound case stiffness parameters

The high specific strength and the high specific modules made graphite epoxy laminate an expedient material substitute for the Shuttle Solid Rocket Motor steel case to substantially increase the payload performance without increasing the composite case axial growth during thrust build up which was constrained to minimize liftoff excitation effects on existing structural elements and interfaces. Parameters associated with axial growth were identified for quality and manufacturing controls. Included is an innovative method for experimentally verifying extensional elastic properties on a laminate pressurized test bottle.

Verderaime, V.↗
NASA NTRS1982

Stiffness reductions during tensile fatigue testing of graphite/epoxy angle-ply laminates

Tensile fatigue data was generated under carefully controlled test conditions. A computerized data acquisition system was used to permit the measurement of dynamic modulus without interrupting the fatigue cycling. Two different 8-ply laminate configurations, viz, + or - 45 (2s) and + or - 67.5 (2s), of a T300/5208 graphite/epoxy composite were tested. The + or - 45 (2s) laminate did exhibit some modulus decay, although there was no well-defined correlation with applied stress level or number of cycles. The + or - 67.5 (2s) laminate did not exhibit any measurable modulus decay. Secondary effects observed included a small but distinct difference between modulus as measured statically and dynamically, a slight recovery of the modulus decay after a test interruption, and a significant viscoelastic (creep) response of the + or - 45 (2s) laminate during fatigue testing.

Odom, E. M.↗
NASA NTRS1983

Numerical methods for stiff systems of two-point boundary value problems

Numerical procedures are developed for constructing asymptotic solutions of certain nonlinear singularly perturbed vector two-point boundary value problems having boundary layers at one or both endpoints. The asymptotic approximations are generated numerically and can either be used as is or to furnish a general purpose two-point boundary value code with an initial approximation and the nonuniform computational mesh needed for such problems. The procedures are applied to a model problem that has multiple solutions and to problems describing the deformation of thin nonlinear elastic beam that is resting on an elastic foundation.

Flaherty, J. E.↗
NASA NTRS1984

Hydrodynamic impeller stiffness, damping, and inertia in the rotordynamics of centrifugal flow pumps

The lateral hydrodynamic forces experienced by a centrifugal pump impeller performing circular whirl motions within several volute geometries were measured. The lateral forces were decomposed into: (1) time averaged lateral forces and (2) hydrodynamic force matrices representing the variation of the lateral forces with position of the impeller center. It is found that these force matrices essentially consist of equal diagonal terms and skew symmetric off diagonal terms. One consequence of this is that during its whirl motion the impeller experiences forces acting normal and tangential to the locus of whirl. Data on these normal and tangential forces are presented; it is shown that there exists a region of positive reduced whirl frequencies, within which the hydrodynamic forces can be destablizing with respect to whirl.

Jery, S.↗
NASA NTRS1985

Stiffness Control of Large Space Structures

A technique for using internal force producing dual element/actuators for vibration suppression of large space structures is proposed. The method is applied to a low order system. Selective modal damping is achieved. The actuators used in this method may be electrically powered. The method is suitable for structures which are too slender or flimsy to permit the use of reaction jet-type actuators.

Fanson, J. L.↗
NASA NTRS1983

Stiffness reductions during tensile fatigue testing of graphite/epoxy angle-ply laminates

The monitoring of modulus decay during fatigue testing as an indicator of damage accumulation and incipient failure has frequently been postulated. The present study was designed to generate tensile fatigue data under carefully controlled test conditions. A computerized data acquisition system was used to permit the measurement of dynamic modulus without interrupting the fatigue cycling. Two different 8-ply laminate configurations, viz, (+ or - 45)2s and (+ or - 67.5)2s, of a T300/5208 graphite/epoxy composite were tested. The (+ or 45)2s laminate did exhibit some modulus decay, although there was no well-defined correlation with applied stress level or number of cycles. The (+ or - 67.5)2s laminate did not exhibit any measurable modulus decay. Secondary effects observed included a slight recovery of the modulus decay after a test interruption, and a significant viscoelastic (creep) response of the (+ or - 45)2s laminate during fatigue testing.

Odom, E. M.↗
NASA NTRS1985

Identification of bearing and seal dynamic stiffness parameters

The results are presented of two simple tests, mainly steady state load test and squeeze film test, for establishing the coefficients of bearings and seals. It also discusses the methodology of the tests and some observed conclusions from the obtained data. Perturbation testing results are given as an example of verification and proof of validity of the two previous tests.

Bently, D. E.↗
NASA NTRS1985

Stiffness control of large space structures

A method of using internal force producing dual element/actuators for vibration suppression of large space structures is proposed. The technique is applied to a vibrating string and to a low order system. Response feedback control for the vibrating string and selected modal control are used for achieving the modal damping. The actuators may be electrically powered and are suitable for structures with extremely low rigidity.

Chen, J. C.↗
NASA NTRS1985

Stiffness control of large space structures

A method of using internal force producing dual element/actuators for vibration suppression of large space structures is proposed. This technique is applied to a vibrating string as well as a low order system. Response feedback control for the vibrating string and selected modal control are used for achieving the modal damping. The actuators used in this method may be electrically powered and are suitable for structures with extremely low rigidity.

Chen, J.-C.↗
NASA NTRS1986

Ultrasonic determination of the elastic constants of the stiffness matrix for unidirectional fiberglass epoxy composites

The elastic constants of a fiberglass epoxy unidirectional composite are determined by measuring the phase velocities of longitudinal and shear stress waves via the through transmission ultrasonic technique. The waves introduced into the composite specimens were generated by piezoceramic transducers. Geometric lengths and the times required to travel those lengths were used to calculate the phase velocities. The model of the transversely isotropic medium was adopted to relate the velocities and elastic constants.

Marques, E. R. C.↗