Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “parametric analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Definition study for photovoltaic residential prototype system

A site evaluation was performed to assess the relative merits of different regions of the country in terms of the suitability for experimental photovoltaic powered residences. Eight sites were selected based on evaluation criteria which included population, photovoltaic systems performance and the cost of electrical energy. A parametric sensitivity analysis was performed for four selected site locations. Analytical models were developed for four different power system implementation approaches. Using the model which represents a direct (or float) charge system implementation the performance sensitivity to the following parameter variations is reported: (1) solar roof slope angle; (2) ratio of the number of series cells in the solar array to the number of series cells in the lead-acid battery; and (3) battery size. For a Cleveland site location, a system with no on site energy storage and with a maximum power tracking inverter which feeds back excess power to the utility was shown to have 19 percent greater net system output than the second place system. The experiment test plan is described. The load control and data acquisition system and the data display panel for the residence are discussed.

Shepard, N. F.↗
NASA NTRS1978

Correlation of chemistry with normal albedo in the Crisium region

The region in the vicinity of the Luna 24 handling site (40-70 deg E; 0-20 deg N) is studied by means of the Apollo orbital fluorescent X-ray Al/Si and Mg/Al data and earth-based normal albedo measurements. By means of unsupervised non-parametric cluster analysis this region is divided into eight surface units. One of these units centered in the Proclus region deviates from the usual trend of increasing normal albedo with increasing Al/Si values and decreasing Mg/Al values

Bielefeld, M. J.↗
NASA NTRS1980

Concept definition study of small Brayton cycle engines for dispersed solar electric power systems

Three first-generation Brayton cycle engine types were studied for solar application: a near-term open cycle (configuration A), a near-term closed cycle (configuration B), and a longer-term open cycle (configuration C). A parametric performance analysis was carried out to select engine designs for the three configurations. The interface requirements for the Brayton cycle engine/generator and solar receivers were determined. A technology assessment was then carried out to define production costs, durability, and growth potential for the selected engine types.

Six, L. D.↗
NASA NTRS1980

Solid state SPS microwave generation and transmission study. Volume 2, phase 2: Appendices

The solid state sandwich concept for SPS was further defined. The design effort concentrated on the spacetenna, but did include some system analysis for parametric comparison reasons. Basic solid state microwave devices were defined and modeled. An initial conceptual subsystems and system design was performed as well as sidelobe control and system selection. The selected system concept and parametric solid state microwave power transmission system data were assessed relevant to the SPS concept. Although device efficiency was not a goal, the sensitivities to design of this efficiency were parametrically treated. Sidelobe control consisted of various single step tapers, multistep tapers and Gaussian tapers. A hybrid concept using tubes and solid state was evaluated. Thermal analyses are included with emphasis on sensitivities to waste heat radiator form factor, emissivity, absorptivity, amplifier efficiency, material and junction temperature.

Maynard, O. E.↗
NASA NTRS1981

Systems design and analysis of the microwave radiometer spacecraft

Systems design and analysis data were generated for microwave radiometer spacecraft concept using the Large Advanced Space Systems (LASS) computer aided design and analysis program. Parametric analyses were conducted for perturbations off the nominal-orbital-altitude/antenna-reflector-size and for control/propulsion system options. Optimized spacecraft mass, structural element design, and on-orbit loading data are presented. Propulsion and rigid-body control systems sensitivities to current and advanced technology are established. Spacecraft-induced and environmental effects on antenna performance (surface accuracy, defocus, and boresight off-set) are quantified and structured material frequencies and modal shapes are defined.

Garrett, L. B.↗
NASA NTRS1981

Advanced oxygen-hydrocarbon Earth-to-orbit propulsion

Liquid oxygen/hydrocarbon (LO2/HC) rocket engine cycles for a surface to orbit transportation system were evaluated. A consistent engine system data base is established for defining advantages and disadvantages, system performance and operating limits, engine parametric data, and technology requirements for candidate engine systems. Preliminary comparisons of the engine cycles utilizing delivered specific impulse values are presented. Methane and propane staged combustion cycles are the highest LO2/HC performers. The hydrogen cooled LO2/methane dual throat engine was found to be the highest performing. Technology needs identified in the study include: high temperature turbines; oxidizer-rich preburners; LO2, methane, and propane cooling; methane and propane fuel-rich preburners; the HC fuel turbopump; and application of advanced composite materials to the engine system. Parametric sensitivity analysis data are displayed which show the effect of variations in engine thrust, mixture ratio, chamber pressure, area ratio, cycle life, and turbine inlet temperature on specific impulse and engine weight.

Obrien, C. J.↗
NASA NTRS1983

Aerodynamic heating and surface temperatures on vehicles for computer-aided design studies

A computer subprogram has been developed to calculate aerodynamic and radiative heating rates and to determine surface temperatures by integrating the heating rates along the trajectory of a vehicle. Convective heating rates are calculated by applying the axisymmetric analogue to inviscid surface streamlines and using relatively simple techniques to calculate laminar, transitional, or turbulent heating rates. Options are provided for the selection of gas model, transition criterion, turbulent heating method, Reynolds Analogy factor, and entropy-layer swallowing effects. Heating rates are compared to experimental data, and the time history of surface temperatures are given for a high-speed trajectory. The computer subprogram is developed for preliminary design and mission analysis where parametric studies are needed at all speeds.

Dejarnette, F. R.↗
NASA NTRS1983

Simulation of spaceborne stereo radar imagery - Experimental results

Computer simulation of radar imagery was used to investigate spaceborne stereo radar. The major conclusions reached are that stereo pairs representing different angles of incidence with the same look-direction appear best and that the angles of incidence and stereo intersection angle be matched to the slope and relief of terrain. A parametric tradeoff analysis was performed for eleven different angles of incidence over three different model areas. The eleven angles spanned the range from small- to large-incidence angles. The three model areas were selected as typical of relatively flat, moderately rough, and mountainous terrain. The stereo pair judged best for each model area are included.

Kaupp, V. H.↗
NASA NTRS1984

An experimental evaluation of the Sternberg task as a workload metric for helicopter Flight Handling Qualities (FHQ) research

The objective was to determine whether the Sternberg item-recognition task, employed as a secondary task measure of spare mental capacity for flight handling qualities (FHQ) simulation research, could help to differentiate between different flight-control conditions. FHQ evaluations were conducted on the Vertical Motion Simulator at Ames Research Center to investigate different primary flight-control configurations, and selected stability and control augmentation levels for helicopters engaged in low-level flight regimes. The Sternberg task was superimposed upon the primary flight-control task in a balanced experimental design. The results of parametric statistical analysis of Sternberg secondary task data failed to support the continued use of this task as a measure of pilot workload. In addition to the secondary task, subjects provided Cooper-Harper pilot ratings (CHPR) and responded to workload questionnaire. The CHPR data also failed to provide reliable statistical discrimination between FHQ treatment conditions; some insight into the behavior of the secondary task was gained from the workload questionnaire data.

Hemingway, J. C.↗
NASA NTRS1984

The Sternberg Task as a Workload Metric in Flight Handling Qualities Research

The objective of this research was to determine whether the Sternberg item-recognition task, employed as a secondary task measure of spare mental capacity for flight handling qualities (FHQ) simulation research, could help to differentiate between different flight-control conditions. FHQ evaluations were conducted on the Vertical Motion Simulator at Ames Research Center to investigate different primary flight-control configurations, and selected stability and control augmentation levels for helicopers engaged in low-level flight regimes. The Sternberg task was superimposed upon the primary flight-control task in a balanced experimental design. The results of parametric statistical analysis of Sternberg secondary task data failed to support the continued use of this task as a measure of pilot workload. In addition to the secondary task, subjects provided Cooper-Harper pilot ratings (CHPR) and responded to a workload questionnaire. The CHPR data also failed to provide reliable statistical discrimination between FHQ treatment conditions; some insight into the behavior of the secondary task was gained from the workload questionnaire data.

Hemingway, J. C.↗
NASA NTRS1986

Application of intersatellite links to domestic satellite systems

The results of a study on intersatellite link (ISL) applications for domestic satellite communications are presented. It was determined if any technical, economic, or performance benefits could be gained by introducing intersatellite links into a domestic satellite communication network. Several key systems issues of domestic ISL's are addressed. These include the effect of a skewed traffic distribution on the selection of ISL satellite orbit locations, tolerable satellite spacing, and crosslink traffic-handling requirements. An ISL technology assessment is made by performing a parametric link analysis for several microwave and optical implementations. The impact of the crosslink on the end-to-end link performance is investigated for both regenerative and nonregenerative ISL architectures. A comparison is made between single satellite systems operating at C-, and Ku-bands and the corresponding ISL systems in terms of ground segment cost, space segment cost, and net link performance. Results indicate that ISL's can effectively expand the CONUS orbital arc, with a 60 GHz ISL implementation being the most attractive.

Ponchak, D. S.↗
NASA NTRS1986

Application of intersatellite links to domestic satellite systems

The results of a study on intersatellite link (ISL) applications for domestic satellite communications are presented. It was determined if any technical, economic, or performance benefits could be gained by introducing intersatellite links into a domestic satellite communication network. Several key systems issues of domestic ISL's are addressed. These include the effect of a skewed traffic distribution on the selection of ISL satellite orbit locations, tolerable satellite spacing, and crosslink traffic-handling requirements. An ISL technology assessment is made by performing a parametric link analysis for several microwave and optical implementations. The impact of the crosslink on the end-to-end link performance is investigated for both regenerative and nonregenerative ISL architectures. A comparison is made between single satellite systems operating at C-, and Ku-bands and the corresponding ISL systems in terms of ground segment cost, space segment cost, and net link performance. Results indicate that ISL's can effectively expand the CONUS orbital arc, with a 60 GHz ISL implementation being the most attractive.

Ponchak, D. S.↗
NASA NTRS1987

A versatile and low order hybrid stress element for general shell geometry

A hybrid stress general shell element is developed based on the Hellinger-Reissner principle modified for relaxed element compatibility conditions. The element is based on a consistent first order thin shell theory with Love Kirchhoff hypotheses. It is of quadrilateral shape with only four corner nodes and five degrees of freedom per node. The geometry of the element is approximated through a bi-cubic polynomial surface patch. Numerical examples consist of torsion-loaded slit cylinder and pinched cylinder with open ends and rigid diaphragmed ends. Also, the representation of the rigid body motion is studied by series of parametric eigenvalue analysis of the stiffness matrix.

Kang, David S.↗
NASA NTRS1989

Modal analysis of gear housing and mounts

Dynamic finite element analysis of a real gear housing is presented. The analysis was conducted for the housing without the rotating components (gears, shafts, and bearings). Both rigid and flexible mounting conditions for the gear housing are considered in this analysis. The flexible support simulates the realistic mounting condition on a rotorcraft, and the rigid one is analyzed for comparison purposes. The effect of gear housing stiffeners is also evaluated. The results indicate that the first six natural modes of the flexibly mounted gear housing in the 0 to 200 Hz range correspond to the translational and rotational rigid body vibration modes of the housing. Above this range, the housing plate elastic modes begin to occur. In the case of the rigid mount, only the housing plate elastic modes are observed which are verified by modal analysis experiments. Parametric studies show that the housing plate stiffeners and rigid mounts tend to increase most of the natural frequencies, the lower ones being affected the most.

Lim, Teik C.↗
NASA NTRS1989

Modal analysis of gear housing and mounts

Dynamic finite element analysis of a real gear housing is presented. The analysis was conducted for the housing without the rotating components (gears, shafts, and bearings). Both rigid and flexible mounting conditions for the gear housing are considered in this analysis. The flexible support simulates the realistic mounting condition on a rotorcraft, and the rigid one is analyzed for comparison purposes. The effect of gear housing stiffeners is also evaluated. The results indicate that the first six natural modes of the flexibly mounted gear housing in the 0 to 200 Hz range correspond to the translational and rotational rigid body vibration modes of the housing. Above this range, the housing plate elastic modes begin to occur. In the case of the rigid mount, only the housing plate elastic modes are observed which are verified by modal analysis experiments. Parametric studies show that the housing plate stiffeners and rigid mounts tend to increase most of the natural frequencies, the lower ones being affected the most.

Lim, Teik C.↗
NASA NTRS1991

Fast Approximate Analysis Of Modified Antenna Structure

Abbreviated algorithms developed for fast approximate analysis of effects of modifications in supporting structures upon root-mean-square (rms) path-length errors of paraboloidal-dish antennas. Involves combination of methods of structural-modification reanalysis with new extensions of correlation analysis to obtain revised rms path-length error. Full finite-element analysis, usually requires computer of substantial capacity, necessary only to obtain responses of unmodified structure to known external loads and to selected self-equilibrating "indicator" loads. Responses used in shortcut calculations, which, although theoretically "exact", simple enough to be performed on hand-held calculator. Useful in design, design-sensitivity analysis, and parametric studies.

Levy, Roy↗
NASA NTRS1991

Industrial Code Development

The industrial codes will consist of modules of 2-D and simplified 2-D or 1-D codes, intended for expeditious parametric studies, analysis, and design of a wide variety of seals. Integration into a unified system is accomplished by the industrial Knowledge Based System (KBS), which will also provide user friendly interaction, contact sensitive and hypertext help, design guidance, and an expandable database. The types of analysis to be included with the industrial codes are interfacial performance (leakage, load, stiffness, friction losses, etc.), thermoelastic distortions, and dynamic response to rotor excursions. The first three codes to be completed and which are presently being incorporated into the KBS are the incompressible cylindrical code, ICYL, and the compressible cylindrical code, GCYL.

Shapiro, Wilbur↗
NASA NTRS1990

Determining structural performance

An overview of the methods and concepts developed to enhance and predict structural dynamic characteristics of advanced aeropropulsion systems is presented. Aeroelasticity, vibration control, dynamic systems, and computational structural methods are four disciplines that make up the structural dynamic effort at LeRC. The aeroelasticity program develops analytical and experimental methods for minimizing flutter and forced vibration of aerospace propulsion systems. Both frequency domain and time domain methods were developed for applications on the turbofan, turbopump, and advanced turboprop. In order to improve life and performance, the vibration control program conceives, analyzes, develops, and demonstrates new methods for controlling vibrations in aerospace systems. Active and passive vibration control is accomplished with electromagnetic dampers, magnetic bearings, and piezoelectric crystals to control rotor vibrations. The dynamic systems program analyzes and verifies the dynamics of interacting systems, as well as develops concepts and methods for high-temperature dynamic seals. Work in this field involves the analysis and parametric identification of large, nonlinear, damped, stochastic systems. The computational structural methods program exploits modern computer science as an aid to the solutions of structural problems.

Ernst, Michael A.↗