Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “parameter studies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Some tests on small-scale rectangular throat ejector

A small scale rectangular throat ejector with plane slot nozzles and a fixed throat area was tested to determine the effects of diffuser sidewall length, diffuser area ratio, and sidewall nozzle position on thrust and mass augmentation. The thrust augmentation ratio varied from approximately 0.9 to 1.1. Although the ejector did not have good thrust augmentation performance, the effects of the parameters studied are believed to indicate probable trends in thrust augmenting ejectors.

Dean, W. N., Jr.↗
NASA NTRS1980

Effect of production microclimate on female thermal state with increased temperature and air humidity

The thermal state of women during the effect of high air temperature and relative humidity with a varying degree of physical loads was studied. Parameters for air temperature, relative humidity, and air movement were established. It was established that in women the thermo-regulatory stress occurs at lower air temperatures and with lower physical loads than in men. The accumulation of heat in women was revealed with lower air temperature than in men. It is concluded that to preserve the normal physiological state of the female organism it is necessary to create more favorable microclimate conditions and decrease the physical loads.

Machablishvili, O. G.↗
NASA NTRS1979

Optimization of space manufacturing systems

Four separate analyses are detailed: transportation to low earth orbit, orbit-to-orbit optimization, parametric analysis of SPS logistics based on earth and lunar source locations, and an overall program option optimization implemented with linear programming. It is found that smaller vehicles are favored for earth launch, with the current Space Shuttle being right at optimum payload size. Fully reusable launch vehicles represent a savings of 50% over the Space Shuttle; increased reliability with less maintenance could further double the savings. An optimization of orbit-to-orbit propulsion systems using lunar oxygen for propellants shows that ion propulsion is preferable by a 3:1 cost margin over a mass driver reaction engine at optimum values; however, ion engines cannot yet operate in the lower exhaust velocity range where the optimum lies, and total program costs between the two systems are ambiguous. Heavier payloads favor the use of a MDRE. A parametric model of a space manufacturing facility is proposed, and used to analyze recurring costs, total costs, and net present value discounted cash flows. Parameters studied include productivity, effects of discounting, materials source tradeoffs, economic viability of closed-cycle habitats, and effects of varying degrees of nonterrestrial SPS materials needed from earth. Finally, candidate optimal scenarios are chosen, and implemented in a linear program with external constraints in order to arrive at an optimum blend of SPS production strategies in order to maximize returns.

Akin, D. L.↗
NASA NTRS1980

Magnetohydrodynamic shock propagation in the vicinity of a magnetic neutral sheet

This paper reports a numerical investigation of the propagation of magnetohydrodynamic (MHD) shocks in the vicinity of magnetic neutral sheets. The attenuation of a shock after passing through a neutral sheet has been evaluated (assuming infinite electrical conductivity). In a parameter study, values of shock speed, polytropic index, plasma beta, and neutral-sheet thickness which are representative of solar coronal conditions have been examined. If solar cosmic rays are accelerated in association with a flare-induced shock (as seems most likely), then our results suggest that the spatial structure of solar particle sources will be influenced by helmet streamers. Such streamers are most readily detectable by H alpha filaments in the underlying chromosphere.

Steinolfson, R. S.↗
NASA NTRS1981

Summary of typical parameters that affect sound transmission through general aviation aircraft structures

This paper presents results of a systematic experimental investigation of parameters which affect sound transmission through general aviation structures. Parameters studied include angle of sound incidence, panel curvature, panel stresses, and edge conditions for bare panels; pane thickness, spacing, inclination of window panes, and depressurization for dual pane windows; densities of hard foam and sound absorption materials, air gaps, and trim panel thickness for multilayered panels. Based on the study, some promising methods for reducing interior noise in general aviation airplanes are discussed.

Grosveld, F.↗
NASA NTRS1982

Precipitating electron energy flux and auroral zone conductances - An empirical model

Data from the low energy electron (LEE) experiments on the Atmosphere Explorer C and D satellites have been used to determine the average global distribution of the energy flux of precipitating auroral electrons and their average energy for different levels of geomagnetic activity. Measurements from the Atmosphere Explorer unified abstract file (15-s resolution) have been binned according to invariant latitude (in the range 50-90 deg), magnetic local time, and geomagnetic activity as measured by the Kp and auroral electrojet (AE) indices, separately. Bin-averaged values of precipitating energy flux and average energy have been calculated, and a smoothing algorithm used to reduce stochastic variations in the raw data. The results indicate that, for the parameters studied, the AE inces does a superior job of ordering the data with regard to geomagnetic activity. The global distribution of the auroral enhancement porition of the Pedersen and Hall conductances were inferred from the data by means of an empirical fit to detailed energy deposition calculations.

Spiro, R. W.↗
NASA NTRS1984

Thematic Mapper Image Processing System (TIPS) Processing Status

Radiometric and geometric correction performance is considered. A one quantum level requirement was met in all spectral bands with an occasional band 7 exception. Initial post launch calibration was accomplished. An absolute radiometric calibration is in progress including an investigation of low impact solution to scan striping. Initial and three downstream updates as well as coordination with LANDSAT D' instrument calibration are planned. Methods and problems in measuring geometric correction performance are examined with an emphasis on temporal registration, geodetic registrtion, and the modeling error budget. Planned efforts include eliminating band 2, band 5 chips; continued performance monitoring; calibration of profile, misalignment angles, and filer parameters; studying the need for seasonal geodetic control points; and improvement of the subpixel correlation technique.

Brooks, J.↗
NASA NTRS1984

Embedded shear layer computations for increased drag reduction

One of the most promising methods of minimizing drag is the reduction of skin friction by injection of low momentum fluid into the near-wall region of turbulent boundary layer flows. This method could be made more effective by limiting the spread rate of the resulting mixing region. In order to achieve a better understanding of how this goal might be achieved, numerical investigations of the relevant fluid dynamic processes governing these regions have been conducted. A compact finite-difference algorithm has been applied to the complete form of the governing conservation equations for a two-dimensional laminar mixing layer. The ability of this computational approach to model successfully the formation and interaction of the large scale vortical structures which dominate such flow fields is verified in the present study. Parameters which affect the spread rate of the mixing region are also identified. In addition, the relative importance of viscous and momentum transport effects in the vortex interactions is determined.

Gatski, T. B.↗
NASA NTRS1984

A mathematical model for the iron/chromium redox battery

A mathematical model has been developed to describe the isothermal operation of a single anode-separator-cathode unit cell in a redox-flow battery and has been applied to the NASA iron/chromium system. The model, based on porous electrode theory, incorporates redox kinetics, mass transfer, and ohmic effects as well as the parasitic hydrogen reaction which occurs in the chromium electrode. A numerical parameter study was carried out to predict cell performance to aid in the rational design, scale-up, and operation of the flow battery. The calculations demonstrate: (1) an optimum electrode thickness and electrolyte flow rate exist; (2) the amount of hydrogen evolved and, hence, cycle faradaic efficiency, can be affected by cell geometry, flow rate, and charging procedure; (3) countercurrent flow results in enhanced cell performance over cocurrent flow; and (4) elevated temperature operation enhances cell performance.

Fedkiw, P. S.↗
NASA NTRS1984

Evaluation of the Malcolm horizon in a moving-base flight simulator

The efficacy of the Malcolm Horizon (MH) in a controlled, simulated, instrument flight environment was examined. Eight flight parameters were used to compare performance under experimental and control conditions. The parameters studied were pitch attitude, roll attitude, turn rate, airspeed, vertical velocity, heading, altitude, and course deviation. Testing of a commercial realization of the MH concept in a flight simulator revealed strengths and weaknesses of the currently available MH hardware.

Gillingham, K. K.↗
NASA NTRS1984

A study on the imaging potential of QUASAT

The orbit, ground array, and sensitivities of the space and ground systems of the QUASAT spaceborne astronomy mission were studied. Parameters which yield images in which the noise is within a factor of three of the thermal noise limit were derived. With a very large ground array QUASAT should produce images as complex as the best of the VLA. At 22 GHz the resolution will be 0.1 milliarcsec, the field of view 15 milliarcsec, and it will be possible to make noise limited maps of complex objects. The QUASAT is essential for mapping southern declination objects. Without QUASAT, even the simple core-jet source cannot be mapped at declination minus 60 deg. It will be possible with QUASAT to make maps with observing times as short as 6 hr although the very best maps will require 48 hr observations.

Readhead, A. C. S.↗
NASA NTRS1984

Cyclic oxidation behavior of beta+gamma overlay coatings on gamma and gamma+gamma-prime alloys

Detailed experimental studies of the cyclic oxidation behavior of low-pressure plasma sprayed beta+gamma coasting on gamma-phase Ni-Cr-Al alloys have shown the correlation of weight change, oxide type, and Cr and Al concentration-distance profiles as a function of oxidation time. Of special interest was the transition to breakway oxidation due to the loss of the Al flux to the oxide and the failure of the coated alloy to form an Al2O3-rich oxide scale. The experimental results on beta+gamma/gamma coating systems were used as the basis of a numerical model (ternary, semi-infinite, finite-difference analysis) which accurately predicted changes in Cr and Al concentration-distance profiles. The model was used to study parameters critical to enhancing the life of coatings which fail by a combination of Al loss in forming the oxide scale and Al loss via interdiffusion with the substrate alloy. Comparisons of beta+gamma/gamma coating behavior are made to the oxidation of coated gamma+gamma-prime substrates, both ternary Ni-Cr-Al alloys and Mar-M 247-type alloys.

Nesbitt, J. A.↗
NASA NTRS1987

Plates and shells containing a surface crack under general loading conditions

Various through and part-through crack problems in plates and shells are considered. The line-spring model of Rice and Levy is generalized to the skew-symmetric case to solve surface crack problems involving mixed-mode, coplanar crack growth. Compliance functions are introduced which are valid for crack depth to thickness ratios at least up to .95. This includes expressions for tension and bending as well as expressions for in-plane shear, out-of-plane shear, and twisting. Transverse shear deformation is taken into account in the plate and shell theories and this effect is shown to be important in comparing stress intensity factors obtained from the plate theory with three-dimensional solutions. Stress intensity factors for cylinders obtained by the line-spring model also compare well with three-dimensional solution. By using the line-spring approach, stress intensity factors can be obtained for the through crack and for part-through crack of any crack front shape, without recalculation integrals that take up the bulk of the computer time. Therefore, parameter studies involving crack length, crack depth, shell type, and shell curvature are made in some detail. The results will be useful in brittle fracture and in fatigue crack propagation studies. All problems considered are of the mixed boundary value type and are reducted to strongly singular integral equations which make use of the finite-part integrals of Hadamard. The equations are solved numerically in a manner that is very efficient.

Joseph, Paul F.↗
NASA NTRS1986

Plates and shells containing a surface crack under general loading conditions

The severity of the underlying assumptions of the line-spring model (LSM) are such that verification with three-dimensional solutions is necessary. Such comparisons show that the model is quite accurate, and therefore, its use in extensive parameter studies is justified. Investigations into the endpoint behavior of the line-spring model have led to important conclusions about the ability of the model to predict stresses in front of the crack tip. An important application of the LSM was to solve the contact plate bending problem. Here the flexibility of the model to allow for any crack shape is exploited. The use of displacement quantities as unknowns in the formulation of the problem leads to strongly singular integral equations, rather than singular integral equations which result from using displacement derivatives. The collocation method of solving the integral equations was found to be better and more convenient than the quadrature technique. Orthogonal polynomials should be used as fitting functions when using the LSM as opposed to simpler functions such as power series.

Joseph, Paul F.↗
NASA NTRS1987

On dynamic loads in parallel shaft transmissions. 1: Modelling and analysis

A model of a simple parallel-shaft, spur-gear transmission is presented. The model is developed to simulate dynamic loads in power transmissions. Factors affecting these loads are identified. Included are shaft stiffness, local compliance due to contact stress, load sharing, and friction. Governing differential equations are developed and a solution procedure is outlined. A parameter study of the solutions is presented in NASA TM-100181 (AVSCOM TM-87-C-3).

Lin, Edward Hsiang-Hsi↗
NASA NTRS1988

Application of structural tailoring to spar/shell turboprops

The problem of designing a swept advanced turboprop (ATP) blade for minimum noise output is discussed. Optimal sweep distributions are found using the computer code STAT (Structural Tailoring of Advanced Turboprops). The initial designs are unswept. The blade designs have minimum noise output while satisfying other blade design requirements. The STAT program and the modifications required during this work are described. Parameter studies of the effect of sweep on noise output are also presented.

Rubinstein, Robert↗
NASA NTRS1989

The role of shock induced trailing-edge separation in limit cycle oscillations

The potential role of shock induced trailing edge separation (SITES) in limit cycle oscillations (LCO) was established. It was shown that the flip-flop characteristics of transition to and from SITES as well as its hysteresis could couple with wing modes with torsional motion and low damping. This connection led to the formulation of a very simple nonlinear math model using the linear equations of motion with a nonlinear step forcing function with hysteresis. A finite difference solution with time was developed and calculations were made for the F-111 TACT were used to determine the step forcing function due to SITES transition. Since no data were available for the hysteresis, a parameter study was conducted allowing the hysteresis effect to vary. Very small hysteresis effects, which were within expected bounds, were required to obtain reasonable response levels that essentially agreed with flight test results. Also in agreement with wind tunnel tests, LCO calculations for the 1/6 scale F-111 model showed that the model should have not experienced LCO.

Cunningham, Atlee M., Jr.↗
NASA NTRS1989

Fracture characteristics of balloon films

An attempt was made to determine the failure modes of high altitude scientific balloons through an investigation of the fracture characteristics of the thin polyethylene films. Two films were the subject of the evaluation, Winzen Int.'s Stratafilm SF-85 and Raven Industries' Astro-E. Research began with an investigation of the film's cold brittleness point and it's effect on the ultimate strength and elasticity of the polyethylene film. A series of preliminary investigations were conducted to develop an understanding of the material characteristics. The primary focus of this investigation was on the notch sensitivity of the films. Simple stress strain tests were also conducted to enable analysis employing fracture toughness parameters. Studies were conducted on both film types at 23 C (room temperature), -60 C, -90 C, and -120 C.

Portanova, Marc A.↗