Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “monotonicity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Invar and Elinvar type amorphous Fe-Cr-B alloys with high corrosion resistance

Amorphous (Fe(1-x)Cr(x))85B15 alloys (x = 0 to 0.15) were prepared from the melts by rapid quenching using a single roller techinque, and their Invar and Elinvar characteristics and corrosion resistance were investigated. With an increase in chromium content the Curie temperature and the saturation magnetic moment per iron atom decreased monotonically, while the crystallization temperature incresed gradually. The thermal expansion coefficient alpha around room temperature became slightly larger with increasing chromium content. Nevertheless, these amorphous alloys exhibited excellent Invar characteristics below the Curie temperature. The value of Young's modulus increased remarkably in a relatively low magnetic field and then saturated at a field of about 80 kA/m, showing a large delta E effect. Its value as well as a longitudinal linear magnetostriction became smaller with an increase in chromium content. The temperature coefficient of Young's modulus changed from postive to negative, and the temperature range showing the Elinvar characteristics became narrower with chromium content. The temperature coefficient of delay time determined from the values of alpha and e was very small. The corrosion resistance of these alloys was extremely improved by chromium addition.

Kikuci, M.↗
NASA NTRS1985

Error growth in operational ECMWF forecasts

A parameterization scheme used at the European Centre for Medium Range Forecasting to model the average growth of the difference between forecasts on consecutive days was extended by including the effect of error growth on forecast model deficiencies. Error was defined as the difference between the forecast and analysis fields during the verification time. Systematic and random errors were considered separately in calculating the error variance for a 10 day operational forecast. A good fit was obtained with measured forecast errors and a satisfactory trend was achieved in the difference between forecasts. Fitting six parameters to forecast errors and differences that were performed separately for each wavenumber revealed that the error growth rate grew with wavenumber. The saturation error decreased with the total wavenumber and the limit of predictability, i.e., when error variance reaches 95 percent of saturation, decreased monotonically with the total wavenumber.

Kalnay, E.↗
NASA NTRS1986

IR heating of the cometary atmosphere

The transfer of radiation, solar and IR dust, in the cometary atmosphere is analyzed using a six-band radiative transfer model. The first five bands correlate with the strongest IR band of H2O and the sixth corresponds to the bulk of solar energy. The radiation field for each band is calculated as a function of the cometocentric distance using the three-stream approximation. It is observed that the mean intensity of the IR radiation field generated by the dust and the cometary nucleus drops from a very large value of about 40,000 erg/sq cm sec at the surface to 400 erg/sq cm sec at 7 km, rises to a peak value of 500 erg/sq cm sec at 100 km and then falls off monotonically. The causes of these changes in radiation field intensity are discussed. The effect of variation of the IR radiation field on the gas temperature is studied.

Marconi, M. L.↗
NASA NTRS1986

Spectral stability of Taylor's vortex array

In a global sense it is shown that the two-dimensional Taylor vortex array, an exact solution of the Navier-Stokes equation, is absolutely and monotonically stable with respect to infinitesimal disturbances of all discrete frequencies as long as the viscosity is positive. It is suggested that the Taylor vortex array may also be stable with respect to finite amplitude disturbances.

Lin, S. P.↗
NASA NTRS1987

X-ray halos in galaxies and clusters of galaxies - Theory

X-ray measurements provide an excellent method to determine the amount and distribution of the dark matter in clusters. Unfortunately, accurate temperature profiles, necessary to this method, are currently not available. However, if the intracluster gas is assumed to have a monotonically decreasing temperature, one finds that the dark matter is strongly concentrated to the cluster center, and has a mass which only exceeds the known baryonic mass by a factor of about three. On a second topic, cooling flows are shown to be a very common feature of cluster central and normal elliptical galaxies. The cooling gas is probably ultimately converted into low mass stars.

Sarazin, Craig L.↗
NASA NTRS1987

A generalized procedure for constructing an upwind-based TVD scheme

A generalized formulation for constructing second- and higher-order accurate TVD (total variation diminishing) schemes is presented. A given scheme is made TVD by limiting antidiffusive flux differences with some nonlinear functions, so-called limiters. The general idea of the formulation and its mathematical proof of Harten's TVD conditions is shown by applying the Lax-Wendroff method to a scalar nonlinear equation and constant-coefficient system of conservation laws. For the system of equations, several definitions are derived for the argument used in the limiter function and present their performance to numerical experiments. Then the formulation is formally extended to the nonlinear system of equations. It is demonstrated that use of the present procedure allows easy conversion of existing central or upwind, and second- or higher-order differencing schemes so as to preserve monotonicity and to yield physically admissible solutions. The formulation is simple mathematically as well as numerically; neither matrix-vector multiplication nor Riemann solver is required. Roughly twice as much computational effort is needed as compared to conventional scheme. Although the notion of TVD is based on the initial value problem, application to the steady Euler equations of the formulation is also made. Numerical examples including various ranges of problems show both time- and spatial-accuracy in comparison with exact solutions.

Liou, Meng-Sing↗
NASA NTRS1987

The dependence of ultraviolet chromospheric emission upon rotation among late-type stars

Integrated fluxes of chromospheric and transition region emission lines have been measured from low-resolution IUE spectra, obtained between 1981 and 1985, of a large number of chromospherically active stars. It is found that chromospherically active stars of the same R(C IV) show a spread in rotation rate that is as large as that of dwarf stars at fixed R(C IV) and that is correlated with spectral type. The UV emission of the active chromospheric stars decreases in strength with declining rotation rate, but shows little dependence upon rotation within individual luminosity classes. It is suggested that the lack of differences noted between rotation-activity relations for single, slowly rotating dwarf stars is due to the monotonic increase of both the average Rossby number and the average rotation period with later spectral type along the main sequence.

Simon, Theodore↗
NASA NTRS1987

Surface pressure fluctuations in a separating turbulent boundary layer

A novel, microphone-employing technique for the measurement of pressure fluctuations through pinhole apertures in the flow surface is used in the present study of separating boundary layer pressure fluctuation spectra and wavespeeds. The rms of the surface pressure fluctuation increases monotonically through the adverse-pressure gradient attached flow region and the detached flow zone. A correlation of the detached flow data is given which is derived from velocity and length scales of the separated flow. The celerity of the surface pressure fluctuations for the attached flow increases with frequency to a maximum, and the streamwise coherence decreases drastically after the begining of flow reversal.

Simpson, Roger L.↗
NASA NTRS1987

Effect of a localized minimum in equatorial field strength on resistive tearing instability in the geomagnetotail

A two-dimensional, resistive-MHD computer code is used to investigate the spontaneous reconnection of magnetotaillike configurations. The initial conditions adopted in the simulations are of two types: (1) in which the equatorial normal magnetic field component B(ze) declines monotonically down the tail, and (2) in which B(ze) exhibits a deep minimum in the near-earth plasma sheet. To represent the case where the earthward convection stops before the X line forms, zero-flow boundary conditions are imposed at the edges of the computational box. The initial configurations are in equilibrium and table within ideal MHD. The dynamic evolution of the system starts after the resistivity is turned on. The main results of these simulations basically support the neutral-line model of substorms and confirm Birn's (1980) computer studies. Spontaneous formation of an X-type neutral point and a single O-type plasmoid with strong tailward flow on the tailward side of the X point is found. The time interval from the turning on of the resistivity to the formation of a plasmoid is much shorter in the case where there is an initial deep minimum. A simple analytic calculation is also carried out to demonstrate why the configuration with a deep minimum is more susceptible to the development of the neutral point.

Hau, L.-N.↗
NASA NTRS1987

The characteristics of gamma-prime dislocation pairs in a nickel-base superalloy

The gamma-prime dislocation pairs of a single crystal nickel-base superalloy, PWA 1480, after tensile and fatigue loading at 650 C are analyzed. The existence and extent of cube cross slip in octahedral slip, and the nature of gamma-prime dislocation pairs in primary cube slip are investigated. It is observed that the PWA 1480 specimens oriented near (001) and (-3 6 10) line directions deform by octahedral slip and specimens oriented near (-1 1 1) and (-2 3 4) lines deform by primary cube slip. It is determined that the overall dislocation distributions are more homogeneous in low cycle fatigue (LCF) loading than in monotonic tensile loading; however, the gamma-prime dislocation pair characteristics are similar for tensile and LCF test specimens. The data reveal that the gamma-prime dislocation pairs of octahedral slip specimens are near-screw and on the cube cross slip plane and for the cube slip specimens, the dislocation pairs are of various characters and on the primary cube slip plane.

Gabb, T. P.↗
NASA NTRS1987

Singular trajectories in airplane cruise-dash optimization

Optimal cruise-dash trajectories are obtained for the case of time-fuel optimization using a linear combination of time and fuel as the performance index. For the case of the steady-state arc being flown at full throttle, the skeletal transient trajectories are also flown at full throttle and the transients approach the cruise-dash points monotonically in an asymptotic fashion. When the steady-state arc is flown at an intermediate throttle, the transient trajectories follow a singular control law and exhibit a complex structure that differs from that of the full-throttle transients. With respect to optimality of the steady-state arc, it is found that although steady-state cruise fails a Jacobi-type condition, steady-state cruise-dash can satisfy this condition if the emphasis on time is sufficiently large.

Bilimoria, Karl D.↗
NASA NTRS1987

The effects of magnetic B(y) component on geomagnetic tail equilibria

A two-dimensional linear magnetohydrostatic model of the magnetotail is developed here in order to investigate the effects of a significant B(y) component on the configuration of magnetotail equilibria. It is concluded that the enhanced B(y) values must be an essential part of the quiet magnetotail and do not result from a simple intrusion of the IMF. The B(y) field consists of a constant background component plus a nonuniform field existing only in the plasma sheet, where it is dependent on the plasma paramater beta and the strength of the magnetic B(z) component. B(y) is strongest at the neutral sheet and decreases monotonically in the + or - z direction, reaching a constant tail lobe value at the plasma sheet boundaries. The presence of a significant positive B(y) component produces currents, including field-aligned currents, that flow through the equatorial plane and toward and away from earth in the northern and southern halves of the plasma sheet, respectively.

Hilmer, Robert V.↗
NASA NTRS1987

Software reliability models for fault-tolerant avionics computers and related topics

Software reliability research is briefly described. General research topics are reliability growth models, quality of software reliability prediction, the complete monotonicity property of reliability growth, conceptual modelling of software failure behavior, assurance of ultrahigh reliability, and analysis techniques for fault-tolerant systems.

Miller, Douglas R.↗
NASA NTRS1987

SHARP simulation of discontinuities in highly convective steady flow

For steady multidimesional convection, the Quadratic Upstream Interpolation for Convective Kinematics (QUICK) scheme has several attractive properties. However, for highly convective simulation of step profiles, QUICK produces unphysical overshoots and a few oscillations, and this may cause serious problems in nonlinear flows. Fortunately, it is possible to modify the convective flux by writing the normalized convected control-volume face value as a function of the normalized adjacent upstream node value, developing criteria for monotonic resolution without sacrificing formal accuracy. This results in a nonlinear functional relationship between the normalized variables, whereas standard methods are all linear in this sense. The resulting Simple High Accuracy Resolution Program (SHARP) can be applied to steady multidimensional flows containing thin shear or mixing layers, shock waves, and other frontal phenomena. This represents a significant advance in modeling highly convective flows of engineering and geophysical importance. SHARP is based on an explicit, conservative, control-volume flux formation, equally applicable to one, two, or three dimensional elliptic, parabolic, hyperbolic, or mixed-flow regimes. Results are given for the bench-mark purely convective first-order results and the nonmonotonic predictions of second- and third-order upwinding.

Leonard, B. P.↗
NASA NTRS1987

Mechanical response of unidirectional boron/aluminum under combined loading

Three test methods were employed to characterize the response of unidirectional Boron/Aluminum metal matrix composite material under monotonic and cyclic loading conditions, namely, losipescu shear, off-axis tension and compression. The characterization of the elastic and plastic response includes the elastic material properties, yielding and subsequent hardening of the unidirectional composite under different stress ratios in the material principal coordinate system. Yield loci generated for different stress ratios are compared for the three different test methods, taking into account residual stresses and specimen geometry. Subsequently, the yield locus for in-plane shear is compared with the prediction of an analytical, micromechanical model. The influence of the scatter in the experimental data on the predicted yield surface is also analyzed. Lastly, the experimental material strengths in tension and compression are correlated with the maximum stress and the Tsai-Wu failure criterion.

Becker, Wolfgang↗
NASA NTRS1988

The 1987 Airborne Antarctic Ozone Experiment: the Nimbus-7 TOMS Data Atlas

Total ozone data taken by the Nimbus-7 Total Ozone Mapping Spectrometer (TOMS) played a central role in the successful outcome of the 1987 Airborne Antarctic Ozone Experiment. The near-real-time TOMS total ozone observations were suppled within hours of real time to the operations center in Punta Arenas, Chile, over a telecommunications network designed specifically for this purpose. The TOMS data preparation and method of transfer over the telecommunications links are reviewed. This atlas includes a complete set of the near-real-time TOMS orbital overpass data over regions around the Palmer Peninsula of Antarctica for the period of August 8 through September 29, 1987. Also provided are daily polar orthographic projections of TOMS total ozone measurements over the Southern Hemisphere from August through November 1987. In addition, a chronology of the salient points of the experiment, along with some latitudinal cross sections and time series at locations of interest of the TOMS total ozone observations are presented. The TOMS total ozone measurements are evaluated along the flight tracks of each of the ER-2 and DC-8 missions during the experiment. The ozone hole is shown here to develop in a monotonic progression throughout late August and September. The minimum total ozone amount was found on 5 October, when its all-time lowest value of 109 DU is recorded. The hole remains well defined, but fills gradually from mid-October through mid-November. The hole's dissolution is observed here to begin in mid-November, when it elongates and begins to rotate. By the end of November, the south pole is no longer located within the ozone hole.

Krueger, Arlin J.↗
NASA NTRS1988

Modeling the viscoplastic behavior of Inconel 718 at 1200 F

A large number of tests, including tensile, creep, fatigue, and creep-fatigue were performed to characterize the mechanical properties of Inconel 718 (a nickel based superalloy) at 1200 F, the operating temperature for turbine blades. In addition, a few attempts were made to model the behavior of Inconel 718 at 1200 F using viscoplastic theories. The Chaboche theory of viscoplasticity can model a wide variety of mechanical behavior, including monotonic, sustained, and cyclic responses of homogeneous, initially-isotropic, strain hardening (or softening) materials. It is shown how the Chaboche theory can be used to model the viscoplastic behavior of Inconel 718 at 1200 F. First, an algorithm was developed to systematically determine the material parameters of the Chaboche theory from uniaxial tensile, creep, and cyclic data. The algorithm is general and can be used in conjunction with similar high temperature materials. A sensitivity study was then performed and an optimal set of Chaboche's parameters were obtained. This study has also indicated the role of each parameter in modeling the response to different loading conditions.

Abdel-Kader, M. S.↗