Results for “model testing” — Page 24

NASA NTRS1983

Scale model performance test investigation of mixed flow exhaust systems for an energy efficient engine /E3/ propulsion system

As part of the NASA Energy Efficient Engine program, scale-model performance tests of a mixed flow exhaust system were conducted. The tests were used to evaluate the performance of exhaust system mixers for high-bypass, mixed-flow turbofan engines. The tests indicated that: (1) mixer penetration has the most significant affect on both mixing effectiveness and mixer pressure loss; (2) mixing/tailpipe length improves mixing effectiveness; (3) gap reduction between the mixer and centerbody increases high mixing effectiveness; (4) mixer cross-sectional shape influences mixing effectiveness; (5) lobe number affects mixing degree; and (6) mixer aerodynamic pressure losses are a function of secondary flows inherent to the lobed mixer concept.

Kuchar, A. P.↗

NASA NTRSDate not supplied

Modeling instrumented test articles for Plasmatron X aerothermal environment

This work discusses the ablative response of thermal protection system materials when exposed to aerothermal environments. It focuses on modeling instrumented test article assemblies tested in the Plasmatron X inductively coupled plasma wind tunnel. For this purpose, as the samples are mounted to a water-cooled arm using numerous assembly components and are embedded with thermocouples for in-depth temperature measurements, the variation in ablative response of the samples as a result of these components is studied. The aerothermal boundary conditions for Plasmatron X are obtained for hypersonic flight-relevant conditions using the multi-physics aerothermal framework built at the University of Illinois at Urbana-Champaign. For simulating the material response, a material response code, Porous Material Analysis Toolbox based on OpenFOAM (PATO) is used. In PATO, numerous configurations and materials of thermocouples were studied. The optimal configuration for obtaining temperature measurements with minimal error using embedded thermocouples was found to be the U-shaped Type S, 30 American wire gauge thermocouple configuration.

Thermal Protection Systems↗

NASA NTRSDate not supplied

Modeling instrumented test articles for Plasmatron X aerothermal environment

This work discusses the ablative response of thermal protection system materials when exposed to aerothermal environments. It focuses on modeling instrumented test article assemblies tested in the Plasmatron X inductively coupled plasma wind tunnel. For this purpose, as the samples are mounted to a water-cooled arm using numerous assembly components and are embedded with thermocouples for in-depth temperature measurements, the variation in ablative response of the samples as a result of these components is studied. The aerothermal boundary conditions for Plasmatron X are obtained for hypersonic flight-relevant conditions using the multi-physics aerothermal framework built at the University of Illinois at Urbana-Champaign. For simulating the material response, a material response code, Porous Material Analysis Toolbox based on OpenFOAM (PATO) is used. In PATO, numerous configurations and materials of thermocouples were studied. The optimal configuration for obtaining temperature measurements with minimal error using embedded thermocouples was found to be the U-shaped Type S, 30 American wire gauge thermocouple configuration.

Thermal Protection Systems↗

NASA NTRS1975

Effects of upper-surface blowing and thrust vectoring on low-speed aerodynamic characteristics of a large-scale supersonic transport model

Tests were conducted in the Langley full-scale tunnel to determine the low-speed aerodynamic characteristics of a large-scale arrow-wing supersonic transport configured with engines mounted above the wing for upper surface blowing, and conventional lower surface engines with provisions for thrust vectoring. A limited number of tests were conducted for the upper surface engine configuration in the high lift condition for beta = 10 in order to evaluate lateral directional characteristics, and with the right engine inoperative to evaluate the engine out condition.

Coe, P. L., Jr.↗

NASA NTRS1976

Effects of upper-surface blowing and thrust vectoring on low speed aerodynamic characteristics of a large-scale supersonic transport model

Tests were conducted in a full scale tunnel to determine the low speed aerodynamic characteristics of a large scale arrow wing supersonic transport configured with engines mounted above the wing for upper surface blowing and conventional lower surface engines having provisions for thrust vectoring. Tests were conducted over an angle of attack range of -10 deg to 34 deg and for Reynolds numbers (based on the mean aerodynamic chord) of 5.17 x 1 million and 3.89 x 1 million. A limited number of tests were also conducted for the upper surface engine configuration in the high lift condition at an angle of sideslip of 10 deg in order to evaluate lateral directional characteristics and with the right engine inoperative in order to evaluate the engine out condition.

Coe, P. L., Jr.↗

NASA NTRS1928

Tests on Models of Three British Airplanes in the Variable Density Wind Tunnel

This report contains the results of tests made in the National Advisory Committee for Aeronautics variable density wind tunnel on three airplane models supplied by the British Aeronautical Research Committee. These models, the BE-2E with R.A.F. 19 wings, the British Fighter with R.A.F. 15 wings, and the Bristol Fighter with R.A.F. 30 wings, were tested over a wide range in Reynolds numbers in order to supply data desired by the Aeronautical Research Committee for scale effect studies. The maximum lifts obtained in these tests are in excellent agreement with the published results of British tests, both model and full scale. No attempt is made to compare drag data, owing to the emission of tail surfaces, radiator, etc., from the model, but is shown that the scale effect observed on the drag coefficients in these tests is due to a large extent to the parts of the models other than the wings. (author)

Higgins, George J↗

NASA NTRS2005

Elevated Temperature Testing and Modeling of Advanced Toughened Ceramic Materials

The purpose of this report is to provide a final report for the period of 12/1/03 through 11/30/04 for NASA Cooperative Agreement NCC3-776, entitled "Elevated Temperature Testing and Modeling of Advanced Toughened Ceramic Materials." During this final period, major efforts were focused on both the determination of mechanical properties of advanced ceramic materials and the development of mechanical test methodologies under several different programs of the NASA-Glenn. The important research activities made during this period are: 1. Mechanical properties evaluation of two gas-turbine grade silicon nitrides. 2) Mechanical testing for fuel-cell seal materials. 3) Mechanical properties evaluation of thermal barrier coatings and CFCCs and 4) Foreign object damage (FOD) testing.

Keith, Theo G.↗

NASA NTRS1976

A comparison of the aerodynamic characteristics at transonic speeds of four wing-fuselage configurations as determined from different test techniques, 4 October 1960

The high speed aerodynamic characteristics of a family of four wing-fuselage configurations of 0, 35, 45, and 60 deg sweepback were determined from transonic bump model tests that were conducted in the Langley high speed 7 by 10 foot tunnel; sting supported model tests were conducted in the Langley 8 foot high speed tunnel and in the Langley high speed 7 by 10 foot tunnel, and rocket model tests were conducted by the Langley Pilotless Aircraft Research Division. A complementary study of the effect of Mach number gradients and streamline curvature on bump results is also included. The qualitative data obtained from the various test facilities for the wing-fuselage configurations were in essential agreement as regards the relative effects of sweepback and Mach number except for drag at zero lift. Quantitatively, important differences were present.

Donlan, C. J.↗

NASA NTRS1977

Transparent materials processing system

A zero gravity processing furnace system was designed that will allow acquisition of photographic or other visual information while the sample is being processed. A low temperature (30 to 400 C) test model with a flat specimen heated by quartz-halide lamps was constructed. A high temperature (400 to 1000 C) test model heated by resistance heaters, utilizing a cylindrical specimen and optics, was also built. Each of the test models is discussed in detail. Recommendations are given.

Hetherington, J. S.↗

NASA NTRS1978

Model fire tests on polyphosphazene rubber and polyvinyl chloride (PVC)/nitrile rubber foams

A video tape record of model room fire tests was shown, comparing polyphosphazene (P-N) rubber and polyvinyl chloride (PVC)/nitrile rubber closed-cell foams as interior finish thermal insulation under conditions directly translatable to an actual fire situation. Flashover did not occur with the P-N foam and only moderate amounts of low density smoke were formed, whereas with the PVC/nitrile foam, flashover occurred quickly and large volumes of high density smoke were emitted. The P-N foam was produced in a pilot plant under carefully controlled conditions. The PVC/nitrile foam was a commercial product. A major phase of the overall program involved fire tests on P-N open-cell foam cushioning.

Widenor, W. M.↗

DOE OSTI2023

Definition of the Stiesdal Offshore TetraSpar Floating Wind System for OC6 Phase IV

The Offshore Code Comparison Collaboration, Continued, with Correlation, and unCertainty (OC6) is an international project focused on verifying and validating modeling tools used in the analysis of floating offshore wind systems. The fourth phase of the project aims to assess the ability of the tools to model a novel floating wind design. The TetraSpar was designed by Stiesdal Offshore Technologies and was selected as the subject platform for the project. The platform is a unique design that features spar-like stability with a very low center of gravity, but does not require rare deep-water ports. This combination is achieved with a system made of two separate steel structures, a hull at the water's surface that supports the wind turbine tower, and a keel that is suspended below the main body. This lower keel has a very high density and drives the total platform's low center of gravity. The TetraSpar, with hull and keel, spar-type stability, and relatively slender components, is unique compared to platforms studied in earlier phases of OC3-OC6 projects, and it offers an opportunity to evaluate the applicability of modeling tools to a novel design, especially unique hydrodynamics and compliant cables. Scaled model tests of the TetraSpar design were performed in 2018-2019 by the University of Maine. The data collected in the model tests provides a detailed description of the response of the platform in various controlled and relatively well understood conditions. Comparison with this data provides a good opportunity for validation of numerical models. The OC6 Phase IV work focuses on the specific parameters used in these scaled model tests. Descriptions of the platform and the test campaign in this document are based on the report written by Allen and Fowler of the University of Maine in 2019.

17 WIND ENERGY↗

NASA NTRS1982

Pilot model hypothesis testing

The aircraft control time history predicted by the optimal control pilot model and actual pilot tracking data obtained from NASA Langley's differential maneuvering simulator (DMS) are analyzed. The analysis is performed using a hypothesis testing scheme modified to allow for changes in the true hypothesis. A finite number of pilot models, each with different hypothesized internal model representations of the aircraft dynamics, are constructed. The hypothesis testing scheme determines the relative probability that each pilot model best matches the DMS data. By observing the changes in probabilities, it is possible to determine when the pilot changes control strategy and which hypothesized pilot model best represent's the pilot's control behavior.

Broussard, J. R.↗

NASA NTRS1936

Tank Tests of Models of Flying Boat Hulls Having Longitudinal Steps

Four models with longitudinal steps on the forebody were developed by modification of a model of a conventional hull and were tested in the National Advisory Committee for Aeronautics (NACA) tank. Models with longitudinal steps were found to have smaller resistance at high speed and greater resistance at low speed than the parent model that had the same afterbody but a conventional V-section forebody. The models with a single longitudinal step had better performance at hump speed and as low high-speed resistance except at very light loads. Spray strips at angles from 0 degrees to 45 degrees to the horizontal were fitted at the longitudinal steps and at the chine on one of the two step models having two longitudinal steps. The resistance and the height of the spray were less with each of the spray strips than without; the most favorable angle was found to lie between 15 degrees and 30 degrees.

Allison, John M↗

NASA NTRS2012

Using a New Crustal Thickness Model to Test Previous Candidate Lunar Basins and to Search for New Candidates

A new crustal thickness model was used to test the viability of 110 candidate large lunar basins previously identified using older topographic and crustal thickness data as well as photogeologic data. The new model was also used to search for new candidate lunar basins greater than 300 km in diameter. We eliminated 11 of 27 candidates previously identified in the older crustal thickness model, and found strong evidence for at least 8 new candidates.

Meyer, H. M.↗

NASA NTRS1991

Use of system identification techniques for improving airframe finite element models using test data

A method for using system identification techniques to improve airframe finite element models was developed and demonstrated. The method uses linear sensitivity matrices to relate changes in selected physical parameters to changes in total system matrices. The values for these physical parameters were determined using constrained optimization with singular value decomposition. The method was confirmed using both simple and complex finite element models for which pseudo-experimental data was synthesized directly from the finite element model. The method was then applied to a real airframe model which incorporated all the complexities and details of a large finite element model and for which extensive test data was available. The method was shown to work, and the differences between the identified model and the measured results were considered satisfactory.

Hanagud, Sathya V.↗

NASA NTRS2009

Modeling and Testing of Phase Transition-Based Deployable Systems for Small Body Sample Capture

This paper summarizes the modeling, simulation, and testing work related to the development of technology to investigate the potential that shape memory actuation has to provide mechanically simple and affordable solutions for delivering assets to a surface and for sample capture and return. We investigate the structural dynamics and controllability aspects of an adaptive beam carrying an end-effector which, by changing equilibrium phases is able to actively decouple the end-effector dynamics from the spacecraft dynamics during the surface contact phase. Asset delivery and sample capture and return are at the heart of several emerging potential missions to small bodies, such as asteroids and comets, and to the surface of large bodies, such as Titan.

flexible appendage↗

NASA NTRS2012

Verification of Ares I Liftoff Acoustic Environments via the Ares Scale Model Acoustic Test

Launch environments, such as Liftoff Acoustic (LOA) and Ignition Overpressure (IOP), are important design factors for any vehicle and are dependent upon the design of both the vehicle and the ground systems. The NASA Constellation Program had several risks to the development of the Ares I vehicle linked to LOA which are used in the development of the vibro-acoustic environments. The risks included cost, schedule and technical impacts for component qualification due to high predicted vibro-acoustic environments. One solution is to mitigate the environment at the component level. However, where the environment is too severe to mitigate at the component level, reduction of the launch environments is required. The Ares I Scale Model Acoustic Test (ASMAT) program was implemented to verify the predicted Ares I launch environments and to determine the acoustic reduction for the LOA environment with an above deck water sound suppression system. The test article included a 5% scale Ares I vehicle model, tower and Mobile Launcher. Acoustic and pressure data were measured by approximately 200 instruments. The ASMAT results are compared to the Ares I LOA predictions and water suppression effectiveness results are presented.

Counter, Douglas D.↗

NASA NTRS2012

Verification of Ares I Liftoff Acoustic Environments via the Ares I Scale Model Acoustic Test

Launch environments, such as Liftoff Acoustic (LOA) and Ignition Overpressure (IOP), are important design factors for any vehicle and are dependent upon the design of both the vehicle and the ground systems. The NASA Constellation Program had several risks to the development of the Ares I vehicle linked to LOA which are used in the development of the vibro-acoustic environments. The risks included cost, schedule and technical impacts for component qualification due to high predicted vibro-acoustic environments. One solution is to mitigate the environment at the component level. However, where the environment is too severe to mitigate at the component level, reduction of the launch environments is required. The Ares I Scale Model Acoustic Test (ASMAT) program was implemented to verify the predicted Ares I launch environments and to determine the acoustic reduction for the LOA environment with an above deck water sound suppression system. The test article included a 5% scale Ares I vehicle model, tower and Mobile Launcher. Acoustic and pressure data were measured by approximately 200 instruments. The ASMAT results are compared to the Ares I LOA predictions and water suppression effectiveness results are presented.

Counter, Douglas D.↗