SEARCH · Engineering Papers

Results for “measured materials properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

All sources NASA NTRS DOE OSTI

NASA NTRS1984

Measuring and Modeling of the Dielectric Properties and Attenuation of Vegetation

The dielectric properties and attenuation of vegetation was measured and modeled. The purpose was to: (1) measure the microwave dielectric properties of vegetation material as a function of moisture content and microwave frequency; (2) develop dielectric mixing models for the vegetation-water mixture; (3) develop a model for the loss factor of a vegetation canopy; (4) relate the results of (1) and (2) to (3); and (5) test the model in (3) against direct canopy transmission measurements.

F Ulaby↗

NASA NTRS1976

A device for rapid determination of thermophysical properties of phase-change wind-tunnel models

An experimental method for direct measurement of the thermophysical properties of wind tunnel heat transfer models was developed. The technique consists of placing the model under a bank of high intensity, radiant heaters so that the fast opening water cooled shutters, which isolate the heater bank from the model, allow a step-input heat rate to be applied. Measurements of the heat transfer rate coupled with a surface-temperature time history of the same material are sufficient to determine the material thermophysical properties. An infrared thermometer is used to measure model surface temperature and a slug calorimeter provides heat transfer rate information. The output from the infrared thermometer and calorimeter is then fed into an analog-to-digital converter which provides digitized data to a computer. This computer then calculates combined thermophysical properties and a teleprinter prints out all the data. Thus, results are available within 7 minutes of test initiation as opposed to the weeks or months required using prior techniques.

Creel, T. R., Jr.↗

NASA NTRS1986

Ultrasonic nondestructive materials characterization

A brief review of ultrasonic wave propagation in solid materials is presented with consideration of the altered behavior in anisotropic and nonlinear elastic materials in comparison with isotropic and linear elastic materials. Some experimental results are described in which ultrasonic velocity and attenuation measurements give insight into materials microstructure and associated mechanical properties. Recent developments with laser beam non-contact generation and detection of ultrasound are presented. The results of several years of experimental measurements using high-power ultrasound are discussed, which provide substantial evidence of the inability of presently accepted theories to fully explain the interaction of ultrasound with solid materials. Finally, a special synchrotron X-ray topographic system is described which affords the possibility of observing direct interaction of ultrasonic waves with the microstructural features of real crystalline solid materials for the first time.

Green, R. E., Jr.↗

NASA NTRS1972

Microphysical, microchemical, and adhesive properties of lunar material. III - Gas interaction with lunar material.

Gas adsorption measurements on an Apollo 12 ultrahigh vacuum-stored sample and Apollo 14 and 15 N2-stored samples, show that the cosmic ray track and solar wind damaged surface of lunar soil is very reactive. Room temperature monolayer adsorption of N2 by the Apollo 12 sample at 0.0001 atm was observed. Gas evolution of Apollo 14 lunar soil at liquid nitrogen temperature during adsorption/desorption cycling is probably due to cosmic ray track stored energy release accompanied by solar gas release from depths of 100-200 nm.

Grossman, J. J.↗

NASA NTRS2001

Development of a Novel Method for Determination of Residual Stresses in a Friction Stir Weld

Material constitutive properties, which describe the mechanical behavior of a material under loading, are vital to the design and implementation of engineering materials. For homogeneous materials, the standard process for determining these properties is the tensile test, which is used to measure the material stress-strain response. However, a majority of the applications for engineering materials involve the use of heterogeneous materials and structures (i.e. alloys, welded components) that exhibit heterogeneity on a global or local level. Regardless of the scale of heterogeneity, the overall response of the material or structure is dependent on the response of each of the constituents. Therefore, in order to produce materials and structures that perform in the best possible manner, the properties of the constituents that make up the heterogeneous material must be thoroughly examined. When materials exhibit heterogeneity on a local level, such as in alloys or particle/matrix composites, they are often treated as statistically homogenous and the resulting 'effective' properties may be determined through homogenization techniques. In the case of globally heterogeneous materials, such as weldments, the standard tensile test provides the global response but no information on what is Occurring locally within the different constituents. This information is necessary to improve the material processing as well as the end product.

Reynolds, Anthony P.↗

NASA NTRS1993

Differential Scanning Calorimetry (DSC) for planetary surface exploration

Differential Scanning Calorimetry (DSC) is the quantitative measurement of the enthalpic response of a material to a systematic change in temperature. In practice, the heat flow into or outward from a sample is measured as the sample is heated or cooled at a carefully controlled rate. DSC superficially resembles, but is not the same as differential thermal analysis (DTA), which is the measurement of temperature differences between a sample and reference material as the pair is heated or cooled. The fundamental properties measured by DSC are enthalpies and temperatures of phase transitions and constant-pressure heat capacities. Depending on instrument design and the nature of the sample, high-quality DSC analyses can be obtained on only a few milligrams of solid materials. DSC requires direct contact with the sample and generally degrades, if not destroys, the sample as a consequence of heating. In laboratory applications, it is common to subject the gaseous effluent from the DSC to analysis by a separate evolved-gas analyzer (EGA).

Gooding, James L.↗

NASA NTRS2003

Multi-sensor electrometer

An array of triboelectric sensors is used for testing the electrostatic properties of a remote environment. The sensors may be mounted in the heel of a robot arm scoop. To determine the triboelectric properties of a planet surface, the robot arm scoop may be rubbed on the soil of the planet and the triboelectrically developed charge measured. By having an array of sensors, different insulating materials may be measured simultaneously. The insulating materials may be selected so their triboelectric properties cover a desired range. By mounting the sensor on a robot arm scoop, the measurements can be obtained during an unmanned mission.

Gompf, Raymond↗

NASA NTRS1975

Conference on Interactions of the Interplanetary Plasma with the Modern and Ancient Moon, George Williams College, Lake Geneva, Wis., September 30-October 4, 1974, Proceedings

The papers deal with solar-wind and magnetospheric interactions with the moon, ancient and present-day lunar surface magnetic and electric fields, the dynamics and evolution of the lunar atmosphere, the lunar record of solar radiation, and nonmeteoric transport of lunar surface materials. Topics discussed include bow-shock protons in the lunar environment, energetic ion events during the lunar night, mapping of the lunar surface magnetic field from orbital observations of mirrored electrons, geomagnetic disturbances induced by the moon, the relationship between lunar topography and limb compressions, measurements of lunar sky brightness, atmospheric supply and loss mechanisms on the moon, the nature and composition of the lunar atmosphere, molecular gas species in that atmosphere, and vacuum-UV spectroscopic measurements of the surface properties of lunar materials. Individual items are announced in this issue.

Source record↗

DOE OSTI2024

A model to separate conduction and radiation in high temperature laser flash measurements for semi-transparent materials

Laser flash analysis (LFA) is a widely used technique in the scientific and industrial communities for measuring the thermal diffusivity and conductivity of materials. However, traditional fitting methods based solely on heat conduction do not account for radiation heat transfer in transparent and semi-transparent materials, which becomes significant at high temperatures. In this study, we have developed a coupled radiation-conduction model that considers the optical properties of materials to accurately extract thermal diffusivity from LFA measurements. We conducted LFA measurements on fused silica glass samples of varying thicknesses and within the temperature range of 25 to 1000 °C and fitted the data with the model. Since the coupled model requires optical properties as input parameters, which are often unavailable for new materials, we have also proposed a modified transparent model. Compared to the coupled model, results from the modified transparent model generally overestimate thermal conductivity, but the errors are acceptable in silica glass with small thickness. Here, we also investigated the applicability of the modified transparent model with materials of different optical properties.

14 SOLAR ENERGY↗

NASA NTRS2012

Containerless Measurements of Density and Viscosity of Fe-Co Alloys

During the past years, extensive collaborative research has been done to understand phase selection in undercooled metals using novel containerless processing techniques such as electrostatic and electromagnetic levitation. Of major interest is controlling a two-step solidification process, double recalescence, in which the metastable phase forms first and then transforms to the stable phase after a certain delay time. The previous research has shown that the delay time is greatly influenced by the internal convection velocity. In the prediction of internal flow, the fidelity of the results depends on the accuracy of the material properties. This research focuses on the measurements of density and viscosity of Fe-Co alloys which will be used for the fluid simulations whose results will support upcoming International Space Station flight experiments.

Lee, Jonghyun↗

DOE OSTI2025

X-ray diffraction strains in laser-ablated aluminum, nickel, sodium, and invar: Pressures to 475 GPa

Dynamically compressed materials in longitudinal waves are described by two physical models: hydrostatic pressure, with equal, normal, principal stresses or material uniaxially strained in the wave propagation direction. These models are disparate, so experimental comparisons and evaluations are important. Polycrystalline material in a state of hydrostatic pressure will have no eccentricity of x-ray-diffracted Debye–Scherrer rings. A general three-dimensional solution of Bragg diffracted x rays based on principal crystallographic strains in the compression wave was found. The distortion of x-ray diffraction beams has been used for strain measurements; the analysis developed incorporates a strained reciprocal lattice and the incident x-ray beam. Strain-distorted Polanyi surfaces form an annulus of compression with an ellipsoid of revolution in reciprocal space, which is intersected by Ewald's sphere for Bragg diffraction. The in situ measurements for strain describe nanosecond diffraction evaluated using two planes, (hkl) and (h′k′l′), both in the same crystallographic phase. Diffraction from Al, Ni, Na, and Invar quantifies the compression axial strains in these materials: The compression axial ratios are 0.65, 1.05, 0.88, and 1.58 at pressures of 291, 402, 409, and 367 GPa for the respective materials. Crystal structure transformations with homogeneous pressurized stresses, mandating equal normal strains, should not be anticipated to agree with heterogeneous, uniaxially strained, and sheared crystalline phases. Measurements support in-plane strains increasing with pressure, p , in fcc and hcp aluminum as ε 22 = −0.21 p /TPa.

Alloys↗

DOE OSTI2023

Overview of a Versatile Loading System for Anisotropic Material Property Characterization

Additive manufacturing, cold rolling, and other thermomechanical treatments on metals, especially HCP, can cause texture and oriented grain structures resulting in anisotropic mechanical properties. This can lead to macroscopic response that significantly deviates from isotropic assumptions which motivates studying mechanical properties in multiple directions. In addition, multiaxial loading and complex stress states overlapping the above mentioned material anisotropy can lead to unexpected outcomes. Idaho National Laboratory developed an advanced mechanical testing system to study a range of uniaxial to multiaxial stress states while measuring the anisotropic response bringing insight into the overlap between material properties and stress states. High-temperature capability and stress- or strain-controlled loading is available to enable a variety of experiment types and conditions to measure elastic, plastic, and viscoplastic properties. This poster presents the design and capabilities of this system with preliminary results highlighting the benefits of multiaxial loading and anisotropic analysis in an integrated system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1982

Ultrasonic measurement of axial stress

The theory of acoustic propagation in strained media is examined, with particular emphasis on rod (bolt) geometries. The continuous wave (CW) approach is the basis of the study, and the theory is developed from a frequency domain analysis standpoint in order to obtain an applied stress/normalized frequency shift relationship. CW measurements may be influenced by such factors as propagation effects, mode conversion, frequency, material properties, and geometry. After the first loading cycle, axial stress measurements for a preloading with an initial frequency of 4.995 36 MHz dropped to 4.989 19 MHz, indicating a 6.17 kHz change. CW and pseudo-CW ultrasonic techniques are found to be reliable for axial stress measurements, and acoustic attenuation measurements correlated to residual stress fields may possibly involve transducer phase cancellation. It is thus concluded that signal drop is an artifact of the transducer directivity, rather than an actual acoustic power decrease.

Heyman, J. S.↗

NASA NTRS2008

Organic/Inorganic Polymeric Composites for Heat-Transfer Reduction

Organic/inorganic polymeric composite materials have been invented with significant reduction in heat-transfer properties. Measured decreases of 20-50 percent in thermal conductivity versus that of the unmodified polymer matrix have been attained. These novel composite materials also maintain mechanical properties of the unmodified polymer matrix. The present embodiments are applicable, but not limited to: racing applications, aerospace applications, textile industry, electronic applications, military hardware improvements, and even food service industries. One specific application of the polymeric composition is for use in tanks, pipes, valves, structural supports, and components for hot or cold fluid process systems where heat flow through materials is problematic and not desired. With respect to thermal conductivity and physical properties, these materials are superior alternatives to prior composite materials. These materials may prove useful as substitutes for metals in some cryogenic applications. A material of this type can be made from a blend of thermoplastics, elastomers, and appropriate additives and processed on normal polymer processing equipment. The resulting processed organic/inorganic composite can be made into fibers, molded, or otherwise processed into useable articles.

Smith, Trent↗

DOE OSTI2020

Magnetoelectric effect arising from a field-induced pseudo Jahn-Teller distortion in a rare-earth magnet

Magnetoelectric materials are attractive for several applications, including actuators, switches, and magnetic field sensors. Typical mechanisms for achieving a strong magnetoelectric coupling are rooted in transition metal magnetism. In sharp contrast, here we identify CsEr(MoO 4 ) 2 as a magnetoelectric material without magnetic transition metal ions, thus ensuring that the Er ions play a key role in achieving this interesting property. Our detailed study includes measurements of the structural, magnetic, and magnetoelectric properties of this material. Bulk characterization and neutron powder diffraction show no evidence for structural phase transitions down to 0.3 K and therefore CsEr(MoO 4 ) 2 maintains the room temperature P2/c space group over a wide temperature range without external magnetic field. These same measurements also identify collinear antiferromagnetic ordering of the Er 3+ moments below T N =0.87K. Complementary dielectric constant and pyroelectric current measurements reveal that a ferroelectric phase with a maximum polarization P~0.6 nC/cm 2 emerges when applying a modest external magnetic field, which indicates that this material has a strong magnetoelectric coupling. Finally, we argue that the magnetoelectric coupling in this system arises from a pseudo Jahn-Teller distortion induced by the magnetic field.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS1998

Ultrasonic Nondestructive Evaluation Techniques Applied to the Quantitative Characterization of Textile Composite Materials

An overall goal of this research has been to enhance our understanding of the scientific principles necessary to develop advanced ultrasonic nondestructive techniques for the quantitative characterization of advanced composite structures. To this end, we have investigated a thin woven composite (5-harness biaxial weave). We have studied the effects that variations of the physical parameters of the experimental setup can have on the ultrasonic determination of the material properties for this thin composite. In particular, we have considered the variation of the nominal center frequency and the f-number of the transmitting transducer which in turn address issues such as focusing and beam spread of ultrasonic fields. This study has employed a planar, two-dimensional, receiving pseudo-array that has permitted investigation of the diffraction patterns of ultrasonic fields. Distortion of the ultrasonic field due to the spatial anisotropy of the thin composite has prompted investigation of the phenomenon of phase cancellation at the face of a finite-aperture, piezoelectric receiver. We have performed phase-sensitive and phase-insensitive analyses to provide a measure of the amount of phase cancellation at the face of a finite-aperture, piezoelectric receiver. The pursuit of robust measurements of received energy (i.e., those not susceptible to phase cancellation at the face of a finite-aperture, piezoelectric receiver) supports the development of robust techniques to determine material properties from measure ultrasonic parameters.

Miller, James G.↗

DOE OSTI2023

High‐Throughput Evaluation of Hardening Coefficients of Eight Alloying Elements in Magnesium

Liquid–solid diffusion couples (LSDCs) are employed to generate a composition gradient in the single‐phase hexagonal closed‐packed (hcp) solid solution with compositions up to the solubility limit of various solutes in Mg. Nanoindentation scanning across the composition gradient in LSDCs allows effective evaluation of composition‐dependent hardness of eight alloying elements (Al, Ca, Ce, Gd, Li, Sn, Y, and Zn) in the hcp Mg phase. The hardening coefficients, an indicator of the potency of solid‐solution hardening, are evaluated from the measured composition‐hardness data and correlated with various materials properties such as atomic radius, shear modulus, and elastic modulus of the solutes. The rank of hardening potency of Al, Gd, Sn, Y, and Zn measured by nanoindentation is in good agreement with that measured by microindentation reported in the literature. The hardening coefficient (potency) from the strongest to the weakest is Ce > Ca > Y ≈ Gd > Zn > Al ≈ Sn > Li in Mg‐based hcp binary solid solutions. The hardening coefficient is found to be closely correlated with the strengthening potency.

36 MATERIALS SCIENCE↗

NASA NTRS1998

Magnesium-Aluminum-Zirconium Oxide Amorphous Ternary Composite: A Dense and Stable Optical Coating

In the present work, the process parameter dependent optical and structural properties of MgO-Al(2)O(3)-ZrO(2) ternary mixed-composite material have been investigated. Optical properties were derived from spectrophotometric measurements. The surface morphology, grain size distributions, crystallographic phases and process dependent material composition of films have been investigated through the use of Atomic Force Microscopy (AFM), X-ray diffraction analysis and Energy Dispersive X- ray (EDX) analysis. EDX analysis made evident the correlation between the optical constants and the process dependent compositions in the films. It is possible to achieve environmentally stable amorphous films with high packing density under certain optimized process conditions.

Sahoo, N. K.↗