Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “materials evaluation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Evaluation of insulation materials and composites for use in a nuclear radiation environment, phase 2

The nuclear heating of the propellant in all of the four baseline RNS configurations studied was much lower than that of the nuclear flight module configuration with the 5000-MW NERVA analyzed previously. Although the nuclear heating has been reduced, the effect of nuclear heating on the propellant as well as the effect of nuclear heating on internal structures such as antivortex baffles, screens, and sump components cannot be neglected. In addition, it was found that the present analytical precedures were not able to predict boundary layer initiation and breakoff points with the accuracy necessary to predict propellant thermodynamic nonequilibrium (stratification) and/or mixing.

Westerheide, D. E.↗
NASA NTRS1973

Evaluation of RSI Materials

Novel attachment and strain-measuring techniques were developed to obtain valid mechanical and thermophysical property data to above 1530 K in air on nonmetallic insulators and their coatings. The lever-arm extensometer developed used for measuring thermal and/or mechanical strain. Thermal expansion measurements were made on a tensile load to define their softening points. Creep characteristics of the insulators were monitored at elevated temperatures and found to become significant above 1090 K (1500 F).

Kistler, C. W.↗
NASA NTRS1977

Development and evaluation of die materials for use in the growth of silicon ribbons by the inverted ribbon growth process, task 2, LSSA project

Silicon sessile drop experiments were performed on a variety of commercially available refractory carbides, nitrides, oxides, and borides to examine the potential of these materials for applications involving either direct contact with molten silicon or as substrates for CVD coatings in the fabrication of dies and crucibles for containing molten silicon. Simultaneous experiments were also conducted with CVD layers of SiC, Si3N4, and SiOxNy. Silicon nitride layers, deposited with NH3:SiH4 ratios ranging from 100:1 down to 5:1, were examined in sessile drop experiments to determine if the layers are degraded as a result of using lower reagent ratios. Preliminary experiments were undertaken on the stability of CVD Si3N4 near the melting point of silicon. Silicon ribbon segments were grown from vitreous carbon dies which had been coated with CVD Si3N4. Depending upon the purity of the die materials, ribbon resistivity values up to 40 Omega cm were obtained.

Duffy, M. T.↗
NASA NTRS1978

Development and evaluation of elastomeric materials for geothermal applications

A material for a casing packer for service for 24 hours in a geothermal environment was developed by synthesis of new elastomers and formulation of available materials. Formulation included use of commercial elastomer gumstocks and also crosslinking of plastic (high Tg) materials. Fibrous reinforcement of fluorocarbon rubbers was emphasized. Organic fiber reinforcement did not increase hot properties significantly. Glass fiber reinforcement gave significant increase in tensile properties. Elongation was reduced, and the glass-reinforced composition examined so far did not hold up well in the geothermal environment. Colloidal asbestos fibers were also investigated. A few experiments with polyphenyl ether gave material with low tensile and high compression set. Available high styrene SBR compositions were studied. Work to date suggests that new synthetic polymers will be required for service in geothermal environments.

Mueller, W. A.↗
NASA NTRS1978

Fire resistivity and toxicity studies of candidate aircraft passenger seat materials

This paper describes fire resistivity studies of a wide range of candidate nonmetallic materials for the construction of improved fire resistant aircraft passenger seats. These materials were evaluated on the basis of FAA airworthiness burn and smoke generation tests, colorfastness, and animal toxicity tests. Physical, mechanical, and aesthetic properties were also included in the evaluations. Candidate seat materials that have significantly improved thermal response to various thermal loads corresponding to reasonable fire threats, as they relate to in-fight fire situations, are identified.

Fewell, L. L.↗
NASA NTRS1978

Development and evaluation of die materials for use in the growth of silicon ribbons by the inverted ribbon growth process, task 2. LSSA project

The results of emission spectroscopic analysis indicate that molten silicon can remain in contact with hot-pressed Si3N4 (99.2 percent theoretical density) for prolonged periods without attaining the impurity content level of the nitride. Although MgO was used as binder, Mg was not found present in the silicon sessile drop in quantities much above the level initially present in the silicon source material. Preliminary experiments with EFG-type dies coated with CVD Si3N4 or CVD SiOxNy indicate that capillary rise does not occur readily in these dies. The same was found to be true of hot-pressed and reaction-sintered Si3N4 obtained commercially. However, when dies were formed by depositing CVD layers on shaped silicon slabs, a column of molten silicon was maintained in each CVD die while being heated in contact with a crucible of molten silicon. Preliminary wetting of dies appears necessary for EFG growth. Several ribbon growth experiments were performed from V-shaped dies.

Duffy, M. T.↗
NASA NTRS1978

Development and Evaluation of Die Materials for Use in the Growth of Silicon Ribbons by the Inverted Ribbon Growth Process. Task 2: LSSA Project

Several ribbon growth experiments were performed from V-shaped dies coated with CVD Si3N4. The most significant result was the ability to perform five consecutive growth runs from the same die without mechanical degradation of the die through temperature cycling. The die was made from vitreous carbon coated with CVD Si3N4. Silicon oxynitride, Si2N2O, was examined with respect to thermal stability in contact with molten silicon. The results of X-ray analysis indicate that this material is converted to both alpha - and beta-Si3N4 in the presence of molten silicon. Experiments on the stability of CVD SiOxNy shoe that this material can be maintained in contact with molten silicon (sessile drop test) for greater than 30 h at 1450 C without total decompositon. These layers are converted mainly to beta-Si3N4.

Duffy, M. T.↗
NASA NTRS1979

Development and Evaluation of Elastomeric Materials for Geothermal Applications

A material was formulated having about 250-350 psi tensile strength and 30-80 percent elongation at 260 C for at least 24 hours in simulated brine. The relationship between these laboratory test results and sealing performance in actual or simulated test conditions is not entirely clear; however, it is believed that no conventional formation or casing packer design is likely to perform well using these materials. The synthetic effort focused on high temperature block copolymers and development of curable polystyrene. Procedures were worked out for synthesizing these new materials. Initial results with heat-cured unfilled polystyrene 'gum' at 260 C indicate a tensile strength of about 50 psi. Cast films of the first sample of polyphenyl quinoxaline-polystyrene block copolymer, which has 'graft-block' structure consisting of a polystyrene chain with pendant polyphenyl quinoxaline groups, show elastomeric behavior in the required temperature range. Its tensile strength and elongation at 260 C were 220-350 psi and 18-36 percent, respectively. All of these materials also showed satisfactory hydrolytic stability.

Mueller, W. A.↗