SEARCH · Engineering Papers

Results for “local stresses”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

All sources NASA NTRS DOE OSTI

NASA NTRS1998

Aerothermal Effects of Cavities and Protuberances for High-Speed Sample Return Capsules

Extraterrestrial sample return is a growing component of solar system exploration. Currently, four missions, Stardust, 1 Muses-C, 2 Genesis, and Mars Sample Return, are under development that employ sample return as a prime component of the mission architecture. Respectively, these missions will return samples from the tail of a comet, an asteroid, the solar wind, and, Mars. An important component of these missions and the focus of this paper is the design of the sample return capsule (SRC). The purpose of the SRC is to safely return to Earth any gathered samples for terrestrial analysis. The two major design constraints for any SRC are as follows: 1) it must be able to survive a high-speed Earth entry (11 km/s to as a high as 15 km/s), 2) the mass of the SRC must be as small as possible. Because the SRC mass is carried from Earth to the sample sight and back, the SRC mass is a strong driver in the mission mass budget. Further, for the Mars Sample Return Capsule, planetary protection is another constraint. For this capsule, the probability of planetary contamination at Earth due to an SRC failure at entry must be minimal. For an SRC, a possible failure mechanism is severe local heating as a result of cavities and or protuberances in the SRC forebody heatshield. For example, the Apollo Command Module had a number of cavities and protuberances as part of the baseline designs Wind-tunnel tests of models containing small cavities and protuberances showed severe local heating augmentations in the vicinity of these surface discontinuities.4-5 As another example, the Genesis SRC forebody heat-shield contains penetrations (cavities) to mount the vehicle to the carrier bus. It is expected that these penetrations will also experience a severe local heating environment. A concern is that the large thermal gradients may produce sufficient thermal stress to cause local mechanical failure of the heatshield. Penetrations to the forebody heat-shield can also result from damage at vehicle integration, during launch, or during transportation of the sample return capsule from earth to the sample site and back. For example, the Starting SRC was damaged near the shoulder during the heatshield integration process producing a local surface discontinuity. Also, the Starting SRC traverses through the tail of a comet and is in space for 7 years. Thus, damage to the heatshield as a result of micrometeroid impact is a concern. Finally, it is difficult to characterize the effects of these potential heatshield singularities with ground-test facilities. Either detailed simulation or a dedicated flight test is required.

Olynick, David↗

NASA NTRS2004

TiAl Scramjet Inlet Flap Subelement Designed and Fabricated

Next-generation launch vehicles are being designed with turbine-based combined cycle (TBCC) propulsion systems having very aggressive thrust/weight targets and long lives. Achievement of these goals requires advanced materials in a wide spectrum of components. TiAl has been identified as a potential backstructure material for maintainable composite panel heat exchangers (HEX) in the inlet, combustor, and nozzle section of a TBCC propulsion system. Weight reduction is the primary objective of this technology. Design tradeoff studies have assessed that a TiAl structure, utilizing a high-strength, hightemperature TiAl alloy called Gamma MET PX,1 reduce weight by 41 to 48 percent in comparison to the baseline Inconel 718 configuration for the TBCC propulsion system inlet, combustor, and nozzle. A collaborative effort between the NASA Glenn Research Center, Pratt & Whitney, Engineering Evaluation & Design, PLANSEE AG (Austria), and the Austrian Space Agency was undertaken to design, manufacture, and validate a Gamma-MET PX TiAl structure for scramjet applications. The TiAl inlet flap was designed with segmented flaps to improve manufacturability, to better control thermal distortion and thermal stresses, and to allow for maintainable HEX segments. The design philosophy was to avoid excessively complicated shapes, to minimize the number of stress concentrations, to keep the part sizes reasonable to match processing capabilities, and to avoid risky processes such as welding. The conceptual design used a standard HEX approach with a double-pass coolant concept for centrally located manifolds. The flowpath side was actively cooled, and an insulation package was placed on the external side to save weight. The inlet flap was analyzed structurally, and local high-stress regions were addressed with local reinforcements.

Draper, Susan L.↗

DOE OSTI2024

Analysis of thermal and mechanical properties with inventory level of the molten salt storage tank in central receiver concentrating solar power plants

Molten salt thermal energy storage (TES) tanks ensure steady power output of concentrating solar power (CSP) plants; however, recent tank failures have highlighted the need for further analysis. Current studies primarily focus on analyzing the molten salt flow, heat transfer, and thermal efficiency. Additionally, research on the latest tank structures is limited and lacks newest experimental validation. This study measures temperature and molten salt inventory levels in the high-temperature tank at a 50 MW central receiver CSP plant, connected to the power grid in 2019. A multi-physics model was developed to evaluate thermal and mechanical properties of TES tanks by combining computational fluid dynamics and finite element modeling using real plant data. Heat loss, temperature, displacement, and stress distribution of the tank at different inventory levels were investigated. Results show that ambient air velocity near the tank roof reaches 2.14 m/s, much higher than 0.2 m/s near the wall. The temperatures of inventory fluid and tank are close, varying slightly at different levels due to thermal conduction and radiation. Because the heat loss strongly depends on temperature, the total tank loss remains nearly constant across inventory levels. Larger temperature gradients and thermal stresses are primarily localized along the tank floor edge and the air-salt interface. Notably, the maximum thermal stress at the tank edge is three times higher than that at the interface. The magnitude of total stress changes by less than 5 MPa with and without thermal load, indicating that high temperatures exert only a minor impact on tank stress. In contrast, thermal load significantly affects tank deformation, particularly at the roof edge, where values exceed 150 mm. Despite the large variation in molten salt levels, tank wall temperatures and displacements present a minor change, suggesting a weak correlation with inventory levels. In conclusion, the findings obtained in this study provide important insights on the TES tank that could be used to optimize tank design and operation strategies.

14 SOLAR ENERGY↗

DOE OSTI2023

Effects of rhodium doping on dislocation nucleation in a [001] SrNi 2 P 2 single crystal under spherical nanoindentation

Nanoindentation was performed on SrNi 2 P 2 single crystals and their dilute solid solutions, Sr(Ni 1–x Rh x ) 2 P 2 (x = 0 ~ 0.055), under [001] loading to investigate the effects of elemental doping on Young’s modulus and dislocation nucleation stress. The results show that Young’s modulus and the dislocation nucleation stress decrease as the Rh content increases, and their Rh content dependence also varies with the Rh content. Electron diffraction analysis and the anisotropic lattice distortion calculations revealed that a local structural transition from the orthorhombic superstructure to the tetragonal structure and local compressive residual stresses could be the main reasons for the decrease in Young’s modulus and dislocation nucleation stress, respectively. The overlap of stress–strain fields between Rh atoms and the associated local structural transition contribute to their Rh content dependence. Here, the results also indicate that elemental doping does not necessarily strengthen materials if the incipient plasticity is controlled by dislocation nucleation, unlike conventional solid solution strengthening.

36 MATERIALS SCIENCE↗

NASA NTRS2024

Analytical Simulation of Effects of Local Mechanisms and Microstructure on Creep Response of Unidirectional Ceramic Matrix Composites

A micromechanics-based method has been developed to analyze the creep response of uncoated ceramic matrix minicomposites. Although the global stress level at which the creep response is analyzed is lower than the composite proportional limit, local stresses are assumed to be high enough that localized damage is present in the composite in the form of matrix microcracks. To model the composite creep response, including the effects of matrix cracking, a fiber shear lag-based methodology is employed. In this approach, stresses are assumed to vary in the fiber as a function of time and distance from the crack plane. The varying stresses are then used to compute the overall creep strain for the composite. Various assumptions regarding the level of matrix microcracking in the composite and the level of creep in the fiber and matrix in various portions of the composite unit cell are also examined. The creep response of the fiber is modeled using a linear Burgers model. The model is applied to a SiCf/SiC unidirectional minicomposite system. The computed creep results are compared to experimentally obtained values. The effects of the local fiber volume fraction on the overall creep response of the composite are also studied. This work will allow increased understanding of the key material damage mechanisms and load sharing that take place during creep conditions and can be expanded to provide improved analysis methods for full macrocomposites.

Micromechanics↗

NASA NTRS2024

Analytical Simulation of the Effects of Local Mechanisms and Microstructure on the Creep Response of Unidirectional Ceramic Matrix Composites

A micromechanics-based method has been developed to analyze the creep response of uncoated ceramic matrix minicomposites. Although the global stress level at which the creep response is analyzed is lower than the composite proportional limit, local stresses are assumed to be high enough that localized damage is present in the composite in the form of matrix microcracks. To model the composite creep response including the effects of matrix cracking, a fiber shear lag-based methodology is employed. In this approach, stresses are assumed to vary in the fiber as a function of time and distance from the crack plane. The varying stresses are then used to compute the overall creep strain for the composite. Various assumptions regarding the level of matrix microcracking in the composite, and the level of creep in the fiber and matrix in various portions of the composite unit cell, are also examined. The creep response of the fiber is modeled using a linear Burgers model. The model is applied to a SiC f /SiC unidirectional minicomposite system. The computed creep results are compared to experimentally obtained values. The effects of the local fiber volume fraction on the overall creep response of the composite are also studied. This work will allow increased understanding of the key material damage mechanisms and load sharing that take place during creep conditions and can be expanded to provide improved analysis methods for full macrocomposites.

Micromechanics↗

NASA NTRS2010

Comparison of Damage Models for Predicting the Non-Linear Response of Laminates Under Matrix Dominated Loading Conditions

Five models for matrix damage in fiber reinforced laminates are evaluated for matrix-dominated loading conditions under plane stress and are compared both qualitatively and quantitatively. The emphasis of this study is on a comparison of the response of embedded plies subjected to a homogeneous stress state. Three of the models are specifically designed for modeling the non-linear response due to distributed matrix cracking under homogeneous loading, and also account for non-linear (shear) behavior prior to the onset of cracking. The remaining two models are localized damage models intended for predicting local failure at stress concentrations. The modeling approaches of distributed vs. localized cracking as well as the different formulations of damage initiation and damage progression are compared and discussed.

Schuecker, Clara↗

DOE OSTI2021

Effect of neighboring grain orientation on strain localization in slip bands in HCP materials

Particularly in plastically anisotropic crystals, such as hexagonal close packed (HCP) materials, plastic deformation is realized by slip acting in the small volumes within individual crystals. Here we extend a full field fast Fourier transform (FFT)-based elasto-viscoplastic formulation to simulate the development of a single slip band on either prismatic or basal planes spanning a crystal. Calculations of the strain and stress fields induced locally within the band and parent crystal, and ahead of the band/grain boundary junction in the neighboring crystal are analyzed as the slip band intensifies under increasing applied strain. We report a substantial influence of the crystallographic orientation of the nearest neighboring grain on the rate of slip band localization. Performing the analysis on two materials, CP-Ti and Mg, indicates that the strength of the material affects the rate of localization, with stronger materials tending to localize more easily. A slip band tip stress-based criterion is proposed for identifying the nearest neighbor orientations in which slip band transmission is possible and the likely slip system for which it occurs. This indicator is validated against experimental studies on commercially pure Ti, an Mg–Y alloy, and Ti–6Al–4V. Finally, we show that for low GB misorientations, the slip band is likely to transmit into another slip band of the same type in the neighbor grain, while for high GB misorientations, it is likely to transmit into one of a different type or to not transmit at all.

36 MATERIALS SCIENCE↗

NASA NTRS1980

Local redistribution of blood under the effect of fixation stress against a background of hypokinesia

Fixation stress was used as a model of emotional disturbance. The effect of previous restrictions on mobility on the local redistribution of blood resulting from fixation stress was examined. Disturbances in carbohydrate which result from prolonged hypokinesia was studied. Radioactivity was used to determine the local redistribution of blood. Modified factor analysis was used to study the results of the experiment.

Kovalev, O. A.↗

DOE OSTI2023

Determining Stress in Metallic Conducting Layers of Microelectronics Devices Using High Resolution Electron Backscatter Diffraction and Finite Element Analysis

Delayed failure due to stress voiding is a concern with some aging microelectronics, as these voids can grow large enough to cause an open circuit. Local measurements of stress in the metallic layers are crucial to understanding and predicting this failure, but such measurements are complicated by the fact that exposing the aluminum conducting lines will relieve most of their stress. In this study, we instead mechanically thin the device substrate and measure distortions on the thinned surface using high resolution electron backscatter diffraction (HREBSD). These measurements are then related to the stresses in the metallic layers through elastic simulations. This study found that in legacy components that had no obvious voids, the stresses were comparable to the theoretical stresses at the time of manufacture (≈300 MPa). Distortion fields in the substrate were also determined around known voids, which may be directly compared to stress voiding models. In conclusion, the technique presented here for stress determination, HREBSD coupled with finite element analysis to infer subsurface stresses, is a valuable tool for assessing failure in layered microelectronics devices.

HREBSD↗

DOE OSTI2022

[Presentation Slides] Code-to-Code Benchmark Study for Thermal Stress Modeling and Preliminary Analysis of the High-temperature Single Heat-Pipe Experiment

In the heat-pipe-cooled microreactor, heat pipes remove heat from the reactor core as a passive heat-transfer device, so the fluid circulation is not required for cooling, which can substantially simplify the overall reactor design. However, given the extremely high temperatures in the core region and potentially large temperature gradients across the structure materials, thermal stresses need to be well-analyzed to ensure structural integrity during normal operations and accident scenarios. This presentation slides discuss finite element method-based thermal-stress analysis for the high-temperature single heat-pipe test article in the Single Primary Heat Extraction and Removal Emulator (SPHERE) facility at Idaho National Laboratory (INL), using two commercial software packages, Abaqus and Star-CCM+. A code-to-code benchmark study was performed to crosscheck the model setup and capability of each code and to gain preliminary insights into the potential thermal stress concerns from the current experimental setup. It is observed the significant thermal stresses happen at the inner surface of the heat pipe hole surrounded by electric heaters where the largest temperature gradients appear. The temperature fields have good agreements between Abaqus and Star-CCM+, while the induced thermal stresses show modest deviations probably due to differences of meshing engines used in these two codes. It is found that the local maximum thermal stresses may reach close to the ultimate tensile strength and yield strength of structural material depending on the heater power. Ultimately, the coupled thermal-structural analysis will help guide the current experimental plan and ensure the facility safety for future experimental study.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1980

Near-wall similarity in a pressure-driven three-dimensional turbulent boundary layer

Mean velocity, measured wall pressure and wall shear stress fields were made in a three dimensional pressure-driven turbulent boundary layer created by a cylinder with trailing edge placed normal to a flat plate floor. The direct force wall shear stress measurements were made with floating element direct force sensing shear meter that responded to both the magnitude and direction of the local wall shear stress. The ability of 10 near wall similarity models to describe the near wall velocity field for the measured flow under a wide range of skewing conditions and a variety of pressure gradient and wall shear vector orientations was used.

Pierce, F. J.↗

NASA NTRS1982

Measurements in a pressure-driven and a shear-driven three-dimensional turbulent boundary layer

Results of mean velocity field, wall static pressure field and simultaneous, direct force measurements of the local wall shear stress magnitude and direction are reported for a pressure-driven and a shear-driven three-dimensional turbulent boundary layer. These data, particularly the direct force local wall shear data, were obtained to test the validity of several of the near-wall similarity models proposed in the literature for such flows.

Pierce, F. J.↗

NASA NTRS1997

Global-Local Finite Element Analysis for Thermo-Mechanical Stresses in Bonded Joints

An analysis of adhesively bonded joints using conventional finite elements does not capture the singular behavior of the stress field in regions where two or three dissimilar materials form a junction with or without free edges. However, these regions are characteristic of the bonded joints and are prone to failure initiation. This study presents a method to capture the singular stress field arising from the geometric and material discontinuities in bonded composites. It is achieved by coupling the local (conventional) elements with global (special) elements whose interpolation functions are constructed from the asymptotic solution.

Shkarayev, S.↗

NASA NTRS1987

On the modelling of non-reactive and reactive turbulent combustor flows

A study of non-reactive and reactive axisymmetric combustor flows with and without swirl is presented. Closure of the Reynolds equations is achieved by three models: kappa-epsilon, algebraic stress and Reynolds stress closure. Performance of two locally nonequilibrium and one equilibrium algebraic stress models is analyzed assuming four pressure strain models. A comparison is also made of the performance of a high and a low Reynolds number model for combustor flow calculations using Reynolds stress closures. Effects of diffusion and pressure-strain models on these closures are also investigated. Two models for the scalar transport are presented. One employs the second-moment closure which solves the transport equations for the scalar fluxes, while the other solves the algebraic equations for the scalar fluxes. In addition, two cases of non-premixed and one case of premixed combustion are considered. Fast- and finite-rate chemistry models are applied to non-premixed combustion. Both show promise for application in gas turbine combustors. However, finite rate chemistry models need to be examined to establish a suitable coupling of the heat release effects on turbulence field and rate constants.

Nikjooy, Mohammad↗

NASA NTRS1984

Fatigue and fracture: Overview

A brief overview of the status of the fatigue and fracture programs is given. The programs involve the development of appropriate analytic material behavior models for cyclic stress-strain-temperature-time/cyclic crack initiation, and cyclic crack propagation. The underlying thrust of these programs is the development and verification of workable engineering methods for the calculation, in advance of service, of the local cyclic stress-strain response at the critical life governing location in hot section compounds, and the resultant crack initiation and crack growth lifetimes.

Halford, G. R.↗

NASA NTRS1995

Differential localization of cytoplasmic myosin II isoforms A and B in avian interphase and dividing embryonic and immortalized cardiomyocytes and other cell types in vitro

Two principal isoforms of cytoplasmic myosin II, A and B (CMIIA and CMIIB), are present in different proportions in different tissues. Isoform-specific monoclonal and polyclonal antibodies to avian CMIIA and CMIIB reveal the cellular distributions of these isoforms in interphase and dividing embryonic avian cardiac, intestinal epithelial, spleen, and dorsal root ganglia cells in primary cell culture. Embryonic cardiomyocytes react with antibodies to CMIIB but not to CMIIA, localize CMIIB in stress-fiber-like-structures during interphase, and markedly concentrate CMIIB in networks in the cleavage furrow during cytokinesis. In contrast, cardiac fibroblasts localize both CMIIA and CMIIB in stress fibers and networks during interphase, and demonstrate slight and independently regulated concentration of CMIIA and CMIIB in networks in their cleavage furrows. V-myc-immortalized cardiomyocytes, an established cell line, have regained the ability to express CMIIA, as well as CMIIB, and localize both CMIIA and CMIIB in stress fibers and networks in interphase cells and in cleavage furrows in dividing cells. Conversely, some intestinal epithelial, spleen, and dorsal root ganglia interphase cells express only CMIIA, organized primarily in networks. Of these, intestinal epithelial cells express both CMIIA and CMIIB when they divide, whereas some dividing cells from both spleen and dorsal root ganglia express only CMIIA and concentrate it in their cleavage furrows. These results suggest that within a given tissue, different cell types express different isoforms of CMII, and that cells expressing either CMIIA or CMIIB alone, or simultaneously, can form a cleavage furrow and divide.

NASA Discipline Developmental Biology↗

DOE OSTI2022

Atomic-scale defects generated in the early/intermediate stages of dielectric breakdown in Si/SiO 2 transistors

In this study, electrically detected magnetic resonance and near-zero-field magnetoresistance measurements were used to study atomic-scale traps generated during high-field gate stressing in Si/SiO 2 MOSFETs. The defects observed are almost certainly important to time-dependent dielectric breakdown. The measurements were made with spin-dependent recombination current involving defects at and near the Si/SiO 2 boundary. The interface traps observed are P b0 and P b1 centers, which are silicon dangling bond defects. The ratio of P b0 /P b1 is dependent on the gate stressing polarity. Electrically detected magnetic resonance measurements also reveal generation of E' oxide defects near the Si/SiO 2 interface. Near-zero-field magnetoresistance measurements made throughout stressing reveal that the local hyperfine environment of the interface traps changes with stressing time; these changes are almost certainly due to the redistribution of hydrogen near the interface.

42 ENGINEERING↗