Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “local control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Analysis and quantification of errors in the geometric correction of satellite images

The quantitative use of remote sensing satellite images in many applications requires that the geometric distortion inherent in these images be corrected, or rectified, to a desired map projection. The most widely used technique relies on ground control points to empirically determine a mathematical coordinate transformation to correct the geometry. In this paper, using the method of least squares, expressions for the accuracy of the geometric transformation and of the rectification of the satellite image to a map projection are derived. Explicit relations between the global accuracy of the transformation and the number, location, and local accuracy of the ground control points are obtained. The results are applied to the correction of a Landsat MSS image.

Ford, G. E.↗
NASA NTRS1992

Active control of interior noise in a large scale cylinder using piezoelectric actuators

The noise reduction effectiveness of two types of control force actuator models has been analytically investigated: (1) a point actuator, and (2) an in-plane, piezoelectric actuator. The actuators were attached to the wall of a simply supported, elastic cylinder closed with rigid end caps. Control inputs to the actuators were determined such that the integrated square of the pressure over the interior of the vibrating cylinder was a minimum. Significant interior noise reductions were achieved for all actuator configurations, but especially for the structurally dominated response. Noise reduction of 9 dB to 26 dB were achieved using point force actuators, as well as localized and extended piezoelectric actuators. Control spillover was found to limit overall performance for all cases. However, the use of extended piezoelectric actuators was effective in reducing control spillover, without increasing the number of control degrees of freedom.

Lester, H. C.↗
NASA NTRS1991

Active control of interior noise in a large scale cylinder using piezoelectric actuators

The noise reduction effectiveness of two types of control force actuator models has been analytically investigated: (1) a point actuator, and (2) an in-plane, piezoelectric actuator. The actuators were attached to the wall of a simply supported, elastic cylinder closed with rigid end caps. Control inputs to the actuators were determined such that the integrated square of the pressure over the interior of the vibrating cylinder was a minimum. Significant interior noise reductions were achieved for all actuator configurations, but especially for the structurally dominated response. Noise reduction of 9 dB to 26 dB were achieved using point force actuators, as well as localized and extended piezoelectric actuators. Control spillover was found to limit overall performance for all cases. However, the use of extended piezoelectric actuators was effective in reducing control spillover, without increasing the number of control degrees of freedom.

Lester, H. C.↗
NASA NTRS2016

Separating the Influence of Environment from Stress Relaxation Effects on Dwell Fatigue Crack Growth in a Nickel-Base Disk Alloy

Both environmental embrittlement and crack tip visco-plastic stress relaxation play a significant role in determining the dwell fatigue crack growth (DFCG) resistance of nickel-based disk superalloys. In the current study performed on the Low Solvus High Refractory (LSHR) disk alloy, the influence of these two mechanisms were separated so that the effects of each could be quantified and modeled. Seven different microstructural variations of LSHR were produced by controlling the cooling rate and the subsequent aging and thermal exposure heat treatments. Through cyclic fatigue crack growth testing performed both in air and vacuum, it was established that four out of the seven LSHR heat treatments evaluated, possessed similar intrinsic environmental resistance to cyclic crack growth. For these four heat treatments, it was further shown that the large differences in dwell crack growth behavior which still persisted, were related to their measured stress relaxation behavior. The apparent differences in their dwell crack growth resistance were attributed to the inability of the standard linear elastic fracture mechanics (LEFM) stress intensity parameter to account for visco-plastic behavior. Crack tip stress relaxation controls the magnitude of the remaining local tensile stresses which are directly related to the measured dwell crack growth rates. It was hypothesized that the environmentally weakened grain boundary crack tip regions fail during the dwells when their strength is exceeded by the remaining local crack tip tensile stresses. It was shown that the classical creep crack growth mechanisms such as grain boundary sliding did not contribute to crack growth, but the local visco-plastic behavior still plays a very significant role by determining the crack tip tensile stress field which controls the dwell crack growth behavior. To account for the influence of the visco-plastic behavior on the crack tip stress field, an empirical modification to the LEFM stress intensity parameter, Kmax, was developed by incorporating into the formulation the remaining stress level concept as measured by simple stress relaxation tests. The newly proposed parameter, Ksrf, did an excellent job in correlating the dwell crack growth rates for the four heat treatments which were shown to have similar intrinsic environmental cyclic fatigue crack growth resistance.

Dwell crack growth↗
NASA NTRS2016

Separating the Influence of Environment from Stress Relaxation Effects on Dwell Fatigue Crack Growth

Seven different microstructural variations of LSHR were produced by controlling the cooling rate and the subsequent aging and thermal exposure heat treatments. Through cyclic fatigue crack growth testing performed both in air and vacuum, it was established that four out of the seven LSHR heat treatments evaluated, possessed similar intrinsic environmental resistance to cyclic crack growth. For these four heat treatments, it was further shown that the large differences in dwell crack growth behavior which still persisted, were related to their measured stress relaxation behavior. The apparent differences in their dwell crack growth resistance were attributed to the inability of the standard linear elastic fracture mechanics (LEFM) stress intensity parameter to account for visco-plastic behavior. Crack tip stress relaxation controls the magnitude of the remaining local tensile stresses which are directly related to the measured dwell crack growth rates. It was hypothesized that the environmentally weakened grain boundary crack tip regions fail during the dwells when their strength is exceeded by the remaining local crack tip tensile stresses. It was shown that the classical creep crack growth mechanisms such as grain boundary sliding did not contribute to crack growth, but the local visco-plastic behavior still plays a very significant role by determining the crack tip tensile stress field which controls the dwell crack growth behavior. To account for the influence of the visco-plastic behavior on the crack tip stress field, an empirical modification to the LEFM stress intensity parameter, Kmax, was developed by incorporating into the formulation the remaining stress level concept as measured by simple stress relaxation tests. The newly proposed parameter, Ksrf, did an excellent job in correlating the dwell crack growth rates for the four heat treatments which were shown to have similar intrinsic environmental cyclic fatigue crack growth resistance.

environmental damage↗
NASA NTRS1994

Peripheral Microvascular Responses to Whole-Body Tilting, G(z) Centrifugation, and Lower Body Negative Pressure Stresses in Humans

The response of the cutaneous microcirculation to orthostatic stress varies along the length of the body due to the interaction of central controls with regional responses to local blood pressure. We hypothesize that artificial orthostatic stresses such as Gz centrifugation and LBNP differ from whole-body tilting in terms of the distribution of microvascular blood flow. Cutaneous microvascular flows were measured by laser Doppler flowmetry at the neck, thigh, and leg of 15 normal subjects. Volunteers underwent stepwise head-up tilt (HUT) and short- and long-arm centrifugation protocols from supine control (0 Gz) to 0.2, 0.4, 0.6, 0.8, 1.0, 0.8, 0.6, 0.4, 0.2, and 0 Gz at the feet, for 30-s periods with 10-s transitions between levels. The same subjects underwent a corresponding supine LBNP protocol, up to 100 mmHg (in 20 mmHg increments) and back to zero pressure, which produced transmural pressure across blood vessels in the foot approximately equal to the HUT protocol. In general, application of all orthostatic stresses produced significant flow reductions in the lower body (p less than 0.05) and inconsistent changes in the neck. At low levels of each stress (0.4 Gz, 40 mmHg), LBNP generated the greatest relative reduction in flow in the lower body (-66.9+/-5.7%, thigh; -60.6 +/-5.7%, leg, mean +/- SE). HUT caused a less severe flow reduction than LBNP at the thigh and leg (-39.9 +/- 8.1% and -55.9+/-4.8%), while the effects induced by both forms of centrifugation were the least profound. Higher levels of each stress generally resulted in similar responses. These responses exhibit a consistent relationship to hypothesized changes in local microvascular transmural pressure, suggesting that myogenic and veno-arteriolar reflexes play a significant role in determining microvascular perfusion during orthostatic stress.

Breit, G. A.↗
NASA NTRS2000

Predictive Multiple Model Switching Control with the Self-Organizing Map

A predictive, multiple model control strategy is developed by extension of self-organizing map (SOM) local dynamic modeling of nonlinear autonomous systems to a control framework. Multiple SOMs collectively model the global response of a nonautonomous system to a finite set of representative prototype controls. Each SOM provides a codebook representation of the dynamics corresponding to a prototype control. Different dynamic regimes are organized into topological neighborhoods where the adjacent entries in the codebook represent the global minimization of a similarity metric. The SOM is additionally employed to identify the local dynamical regime, and consequently implements a switching scheme that selects the best available model for the applied control. SOM based linear models are used to predict the response to a larger family of control sequences which are clustered on the representative prototypes. The control sequence which corresponds to the prediction that best satisfies the requirements on the system output is applied as the external driving signal.

Motter, Mark A.↗
NASA NTRS1989

Concurrent hypercube system with improved message passing

A network of microprocessors, or nodes, are interconnected in an n-dimensional cube having bidirectional communication links along the edges of the n-dimensional cube. Each node's processor network includes an I/O subprocessor dedicated to controlling communication of message packets along a bidirectional communication link with each end thereof terminating at an I/O controlled transceiver. Transmit data lines are directly connected from a local FIFO through each node's communication link transceiver. Status and control signals from the neighboring nodes are delivered over supervisory lines to inform the local node that the neighbor node's FIFO is empty and the bidirectional link between the two nodes is idle for data communication. A clocking line between neighbors, clocks a message into an empty FIFO at a neighbor's node and vica versa. Either neighbor may acquire control over the bidirectional communication link at any time, and thus each node has circuitry for checking whether or not the communication link is busy or idle, and whether or not the receive FIFO is empty. Likewise, each node can empty its own FIFO and in turn deliver a status signal to a neighboring node indicating that the local FIFO is empty. The system includes features of automatic message rerouting, block message transfer and automatic parity checking and generation.

Peterson, John C.↗
NASA NTRS1988

Telerobotics - Problems and research needs

With major emphasis on simulation, a university laboratory telerobotics facility permits problems to be approached by groups of graduate students. Helmet-mounded displays provide realism; the slaving of the display to the human operator's viewpoint gives a sense of 'telepresence' that may be useful for prolonged tasks. Using top-down three-dimensional model control of distant images allows distant images to be reduced to a few parameters to update the model used for display to the human operator in a preview mode to circumvent, in part, the communication delay. Also, the model can be used as a format for supervisory control and permit short-term local autonomous operations. Image processing algorithms can be made simpler and faster without trying to construct sensible images from the bottom. Control studies of telerobots lead to preferential manual control modes and basic paradigms for human motion and thence, perhaps, to redesign of robotic control, trajectory path planning, and rehabilitation prosthetics.

Stark, Lawrence↗
NASA NTRS2004

Future Concepts for Realtime Data Interfaces for Control Centers

Existing methods of exchanging realtime data between the major control centers in the International Space Station program have resulted in a patchwork of local formats being imposed on each Mission Control Center. This puts the burden on a data customer to comply with the proprietary data formats of each data supplier. This has increased the cost and complexity for each participant, limited access to mission data and hampered the development of efficient and flexible operations concepts. Ideally, a universal format should be promoted in the industry to prevent the unnecessary burden of each center processing a different data format standard for every external interface with another center. With the broad acceptance of XML and other conventions used in other industries, it is now time for the Aerospace industry to fully engage and establish such a standard. This paper will briefly consider the components that would be required by such a standard (XML schema, data dictionaries, etc.) in order to accomplish the goal of a universal low-cost interface, and acquire broad industry acceptance. We will then examine current approaches being developed by standards bodies and other groups. The current state of CCSDS panel work will be reviewed, with a survey of the degree of industry acceptance. Other widely accepted commercial approaches will be considered, sometimes complimentary to the standards work, but sometimes not. The question is whether de facto industry standards are in concert with, or in conflict with the direction of the standards bodies. And given that state of affairs, the author will consider whether a new program establishing its Mission Control Center should implement a data interface based on those standards. The author proposes that broad industry support to unify the various efforts will enable collaboration between control centers and space programs to a wider degree than is currently available. This will reduce the cost for programs to provide realtime access to their data, hence reducing the cost of access to space, and benefiting the industry as a whole.

Kearney, Mike W., III↗
NASA NTRS1997

Fuel Cell Power Plant Initiative: Solid Oxide Fuel Cell/Logistics Fuel Processor 27 kWe Power System Demonstration for ARPA - Volume 1

This report describes the successful testing of a 27 kWe Solid Oxide Fuel Cell (SOFC) generator fueled by natural gas and/or a fuel gas produced by a brassboard logistics fuel preprocessor (LFP). The test period began on May 24, 1995 and ended on February 26, 1996 with the successful completion of all program requirements and objectives. During this time period, this power system produced 118.2 MWh of electric power. No degradation of the generator's performance was measured after 5582 accumulated hours of operation on these fuels: local natural gas - 3261 hours, jet fuel reformate gas - 766 hours, and diesel fuel reformate gas - 1555 hours. This SOFC generator was thermally cycled from full operating temperature to room temperature and back to operating temperature six times, because of failures of support system components and the occasional loss of test site power, without measurable cell degradation. Numerous outages of the LFP did not interrupt the generator's operation because the fuel control system quickly switched to local natural gas when an alarm indicated that the LFP reformate fuel supply had been interrupted. The report presents the measured electrical performance of the generator on all three fuel types and notes the small differences due to fuel type. Operational difficulties due to component failures are well documented even though they did not affect the overall excellent performance of this SOFC power generator. The final two appendices describe in detail the LFP design and the operating history of the tested brassboard LFP.

Veyo, S.E.↗
NASA NTRS2005

Phase control of electromagnetically induced transparency and its applications to tunable group velocity and atom localization

We show that, by simple modifications of the usual three-level lambda-type scheme used in electromagnetically induced transparency (EIT) schemes, phase dependence in the response of the atomic medium to a weak probe field can be introduced. This gives rise to phase dependent susceptibility. By properly controlling phase and amplitudes of the drive fields we obtain variety of interesting effects. On one hand we obtain phase control of the group velocity of a probe field passing through medium to the extend that continuous tuning of the group velocity from subluminal to superluminal and back is possible. While on the other hand, by choosing one of the drive fields to be a standing wave field inside a cavity, we obtain sub-wavelength localization of moving atoms passing through the cavity field.

Zubairy, M. Suhail↗
NASA NTRS1993

Exact methods for modal transient response analysis including feedback control

This paper presents a modal method for the analysis of controlled structural systems that retains the uncoupled nature of the classical transient response analysis of a structure subjected to a prescribed time-varying load. The control force is expanded as a Taylor series that remains on the right side of the equations, and it does not lead to a computational approach that requires coupling between modes on the left side. Retaining a sufficient number of terms in the series produces a solution to the modal equations that is accurate to machine precision. The approach is particularly attractive for large problems in which standard matrix exponential methods become computationally prohibitive. Numerical results are presented to show the accuracy and efficiency of the proposed approach for dynamic feedback compensation of a truss structure with local member modes in the controller bandwidth.

Anderson, Melvin S.↗
NASA NTRS2011

Distributed Aerodynamic Sensing and Processing Toolbox

A Distributed Aerodynamic Sensing and Processing (DASP) toolbox was designed and fabricated for flight test applications with an Aerostructures Test Wing (ATW) mounted under the fuselage of an F-15B on the Flight Test Fixture (FTF). DASP monitors and processes the aerodynamics with the structural dynamics using nonintrusive, surface-mounted, hot-film sensing. This aerodynamic measurement tool benefits programs devoted to static/dynamic load alleviation, body freedom flutter suppression, buffet control, improvement of aerodynamic efficiency through cruise control, supersonic wave drag reduction through shock control, etc. This DASP toolbox measures local and global unsteady aerodynamic load distribution with distributed sensing. It determines correlation between aerodynamic observables (aero forces) and structural dynamics, and allows control authority increase through aeroelastic shaping and active flow control. It offers improvements in flutter suppression and, in particular, body freedom flutter suppression, as well as aerodynamic performance of wings for increased range/endurance of manned/ unmanned flight vehicles. Other improvements include inlet performance with closed-loop active flow control, and development and validation of advanced analytical and computational tools for unsteady aerodynamics.

Brenner, Martin↗
NASA NTRS1999

Design and Development of Lateral Flight Director

The current control law used for the flight director in the Boeing 737 simulator is inadequate with large localizer deviations near the middle marker. Eight different control laws are investigated. A heuristic method is used to design control laws that meet specific performance criteria. The design of each is described in detail. Several tests were performed and compared with the current control law for the flight director. The goal was to design a control law for the flight director that can be used with large localizer deviations near the middle marker, which could be caused by winds or wake turbulence, without increasing its level of complexity.

Kudlinski, Kim E.↗
NASA NTRS1994

The head and neck discomfort of autonomic failure: an unrecognized aetiology of headache

Information concerning the frequency, severity, character, location, duration, diurnal pattern of headache and ancillary symptoms were obtained in 25 patients with autonomic failure and 44 control subjects. Precipitating and ameliorating factors were identified. Autonomic failure patients had more head and neck discomfort than controls. Their discomfort was much more likely to localize in the occiput, nape of the neck and shoulder, compared with controls. There was a greater tendency for the discomfort to occur in the morning and after meals. It was sometimes less than 5 min in duration and was often associated with dimming, blurring, or tunnelling of vision. It was provoked by upright posture and relieved by lying down. Patients with severe autonomic failure and orthostatic hypotension often present with a posture-dependent headache or neck pain. Because the relationship of these symptoms to posture is often not recognized, the fact that these findings may signal an underlying autonomic disorder is underappreciated, and the opportunity to consider this aetiology for the headache may be missed.

NASA Discipline Regulatory Physiology↗
NASA NTRS1981

Automatic control algorithm effects on energy production

A computer model was developed using actual wind time series and turbine performance data to simulate the power produced by the Sandia 17-m VAWT operating in automatic control. The model was used to investigate the influence of starting algorithms on annual energy production. The results indicate that, depending on turbine and local wind characteristics, a bad choice of a control algorithm can significantly reduce overall energy production. The model can be used to select control algorithms and threshold parameters that maximize long term energy production. The results from local site and turbine characteristics were generalized to obtain general guidelines for control algorithm design.

Mcnerney, G. M.↗