Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hydrogen component”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Electromagnetic dampers for cryogenic applications

Cryogenic turbomachinery of the type used to pump high-pressure liquid hydrogen at -423 F and liquid oxygen at -297 F to the main engines of the Space Shuttle are subjected to lateral rotor vibrations from unbalance forces and transient loads. Conventional dampers which utilize viscous fluids such as lubricating oil cannot be used in turbopumps because the bearing components are filled with either liquid hydrogen or liquid oxygen, which have viscosity comparable to air and, therefore, are not effective in viscous dampers. Electromagentic dampers are currently being explored as a means of providing damping in cryogenic turbopumps because their damping effectiveness increases as temperature decreases and because they are compatible with the liquid hydrogen or liquid oxygen in the turbopumps.

Brown, Gerald V.↗

Evaluation of Alternate Stainless Steel Surface Treatments for Mass Spectroscopy and Other Tritium Systems

There are specific components in the SRS Tritium Facilities that are required to introduce as few chemical impurities (such as protium and methane) as possible into the process gas. Two such components are the inlet systems for the mass spectroscopy facilities and hydrogen isotope mix standard containers. Two vendors now passivate stainless steel components for these systems, and both are relatively small businesses whose future viability can be questioned, which creates the need for new sources. Stainless steel containers were designed to evaluate alternate surface treatment vendors for tritium storage and handling for these high purity tritium systems. Five vendors applied their own 'best' surface treatments to two containers each - one was a current vendor, another was a chemical vapor deposited silicon coating, and the other three were electropolishing and chemical cleaning vendors. Pure tritium gas was introduced into all ten containers and the composition was monitored over time. The only observed impurities in the gas were some HT, less CT 4 , and very small amounts of T 2 O in all cases. The currently used vendor treated containers contained the least impurities. The chemical vapor deposited silicon treatment resulted in the highest impurity levels. Sampling one set of containers after about one month of tritium exposure revealed the impurity level to be nearly the same as that after more than a year of exposure - this result suggests that cleaning new stainless steel components by tritium gas contact for about a month may be a worthy operation.

03 NATURAL GAS↗

Air Force NiH2 IPV storage testing

USAF Phillips Laboratory Nickel Hydrogen IPV storage test, performed at the Naval Surface Warfare Center (NSWC) at Crane Indiana, is discussed. The storage tests is just one component of the USAF Phillips Laboratory Nickel Hydrogen IPV Test Program. The plan was to store cells for a defined period and cycle matching cells to determine the effect on cycle life. The storage period was completed in April 95 and the cycling cells have achieved five years of real time LEO cycling. The two main objectives of the storage test are: to investigate various methods on NiH2 cells by using two different manufacturers and two different storage methods or conditions, and to determine the effect of storage method on cycle performance and cycle life by using matching cells cycling at 25% depth of discharge. The comparisons between individual cycle performance as well as cycle life are also reported. During the test the following variables has been considered: constant potential, cell current, open circuit voltage, and temperature. The results of the test are also discussed using charts and tables.

Smellie, Shawn↗

PROPERTIES OF CARBON–OXYGEN WHITE DWARFS FROM MONTE CARLO STELLAR MODELS

We investigate properties of carbon–oxygen white dwarfs with respect to the composite uncertainties in the reaction rates using the stellar evolution toolkit, Modules for Experiments in Stellar Astrophysics (MESA) and the probability density functions in the reaction rate library STARLIB. These are the first Monte Carlo stellar evolution studies that use complete stellar models. Focusing on 3 M{sub ⊙} models evolved from the pre main-sequence to the first thermal pulse, we survey the remnant core mass, composition, and structure properties as a function of 26 STARLIB reaction rates covering hydrogen and helium burning using a Principal Component Analysis and Spearman Rank-Order Correlation. Relative to the arithmetic mean value, we find the width of the 95% confidence interval to be ΔM{sub 1TP} ≈ 0.019 M{sub ⊙} for the core mass at the first thermal pulse, Δt{sub 1TP} ≈ 12.50 Myr for the age, Δlog(T{sub c}/K) ≈ 0.013 for the central temperature, Δlog(ρ{sub c}/g cm{sup −3}) ≈ 0.060 for the central density, ΔY{sub e,c} ≈ 2.6 × 10{sup −5} for the central electron fraction, ΔX{sub c}({sup 22}Ne) ≈ 5.8 × 10{sup −4}, ΔX{sub c}({sup 12}C) ≈ 0.392, and ΔX{sub c}({sup 16}O) ≈ 0.392. Uncertainties in the experimental {sup 12}C(α,γ){sup 16}O, triple-α, and {sup 14}N(p,γ){sup 15}O reaction rates dominate these variations. We also consider a grid of 1–6 M{sub ⊙} models evolved from the pre main-sequence to the final white dwarf to probe the sensitivity of the initial–final mass relation to experimental uncertainties in the hydrogen and helium reaction rates.

79 ASTRONOMY AND ASTROPHYSICS↗

Helical muon beam cooling channel engineering design

The Helical Cooling Channel (HCC) achieves effective ionization cooling of the six-dimensional (6d) phase space of a muon beam by means of a series of 21st century inventions. In the HCC, hydrogen-pressurized RF cavities enable high RF gradients in strong external magnetic fields. The theory of the HCC, which requires a magnetic field with solenoid, helical dipole, and helical quadrupole components, demonstrates that dispersion in the gaseous hydrogen energy absorber provides effective emittance exchange to enable longitudinal ionization cooling. The 10-year development of a practical implementation of a muon-beam cooling device has involved a series of technical innovations and experiments that imply that an HCC of less than 300 m length can cool the 6d emittance of a muon beam by six orders of magnitude. We describe the design and construction plans for a prototype HCC module based on oxygen-doped hydrogen-pressurized RF cavities that are loaded with dielectric, fed by magnetrons, and operate in a superconducting helical solenoid magnet. The first phase of this project saw the development of a conceptual design for the integration of 805 MHz RF cavities into a 10 T Nb 3 Sn-based HS test section. Two very novel ideas are required to realize the design. The first idea is the use of dielectric inserts in the RF cavities to make them smaller for a given frequency so that the cavities and associated plumbing easily fit inside the magnet cryostat. Calculations indicate that heat loads will be tolerable, while RF breakdown of the dielectric inserts will be suppressed by the pressurized hydrogen gas. The second new idea is the use of a multi-layer Nb 3 Sn helical solenoid. The technology demonstrations for the two aforementioned key components of a 10T, 805 MHz HCC were begun in this project. The work load in the Fermilab Technical Division made it difficult to test a multi-layer Nb 3 Sn solenoid as originally planned. Instead, a complementary project was approved by the DOE Technical Topic Manager to develop magnets for the Mu2e experiment that fit well into the Fermilab Technical Division availability. The difference between the MCC helical solenoid and the Mu2e bent solenoid described in Appendix I is that the helical solenoid is made of coils that are in parallel planes with offset centers, while the coils in the bent solenoid follow the central particle trajectory and look much like a “slinky” toy. The muon-beam cooling-channel technologies developed in this project will enable a muon collider, the next step toward the energy frontier, Higgs/neutrino/Z-factories, and rare muon decay experiments. Commercial uses of the beams made possible by the cooling techniques developed in this project include scanning for nuclear contraband, studies of material properties with spin resonance techniques, and muon-catalyzed fusion.

43 PARTICLE ACCELERATORS↗

In Situ Studies of Copper-Zirconia-Zinc Oxide Model Catalysts for CO 2 Hydrogenation

A combination of in situ X-ray photoelectron spectroscopy (XPS) and infrared reflection absorption spectroscopy (IRAS) was used to investigate the formation of surface intermediates from CO 2 hydrogenation on copper-zirconia-zinc oxide model catalysts under reaction conditions. Copper clusters with different numbers of atoms (n = 1, 4, 13) were deposited onto bare and ZrO 2 -modified ZnO powder supports to systematically examine the effects of Cu cluster size and the synergy between metal and metal-oxide components. Under low pressure CO 2 hydrogenation conditions (CO 2 :H 2 = 1:9, 0.4 mbar, 300–600 K), XPS and IRAS identify the most prominent intermediates as carbonate (CO 3 *), formate (HCOO*) and methoxy (CH 3 O*), which is the final surface-bound intermediate leading to methanol. The temperature profiles are consistent with a mechanism in which CO 2 is adsorbed as carbonate species (HCO 3 *, CO 3 *) followed by hydrogenation reactions to formate (HCOO*) and methoxy (CH 3 O*), but the relative yields strongly depend on surface composition. Specifically, the presence of ZrO 2 promotes CO 2 adsorption and activation and improves the thermal stability of the Cu clusters against loss of surface area. Moreover, the ternary Cu 4 /ZrO 2 /ZnO surface is significantly more active than Cu 4 /ZnO and ZrO 2 /ZnO surfaces for the formation of methoxy (CH 3 O*), indicating that Cu–ZrO 2 interfaces promote the formation of key intermediates leading to methanol. Finally, the yields of intermediates are similar for all Cu cluster sizes (Cu 1 , Cu 4 and Cu 13 ), indicating that the primary role of Cu is to provide H atoms via H 2 dissociation and spillover. In conclusion, these molecular-level insights provide a fundamental understanding of the enhanced efficiency of ternary Cu–ZrO 2 –ZnO catalysts and establish design principles for developing improved catalysts for CO 2 conversion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Precision Spectroscopy of Hydrogen with a Lamb-Shift Polarimeter

A spinfilter, the most important component of a Lamb-shift polarimeter, is used to produce a beam of metastable hydrogen (deuterium) atoms in one hyperfine state (HFS)(alpha1, alpha2 and together with the Sona transition beta3). As function of a magnetic field separated transitions between the 2s{sub 1/2} metastable Zeeman states seem to be observable as well as single transitions into the short-lived 2P{sub 1/2} and 2P{sub 3/2} states. The Breit-Rabi diagrams for these states and, therefore, the g factors can be measured with good precision. Furthermore, the hyperfine splittings and the Lamb shift can be observed as well. Application of this method to anti-hydrogen atoms is suggested.

74 ATOMIC AND MOLECULAR PHYSICS↗

The Integration of a Structural Water Gas Shift Catalyst with a Vanadium Alloy Hydrogen Transport Device

This project is in response to a requirement for a system that combines water gas shift technology with separation technology for coal derived synthesis gas. The justification of such a system would be improved efficiency for the overall hydrogen production. By removing hydrogen from the synthesis gas stream, the water gas shift equilibrium would force more carbon monoxide to carbon dioxide and maximize the total hydrogen produced. Additional benefit would derive from the reduction in capital cost of plant by the removal of one step in the process by integrating water gas shift with the membrane separation device. The answer turns out to be that the integration of hydrogen separation and water gas shift catalysis is possible and desirable. There are no significant roadblocks to that combination of technologies. The problem becomes one of design and selection of materials to optimize, or at least maximize performance of the two integrated steps. A goal of the project was to investigate the effects of alloying elements on the performance of vanadium membranes with respect to hydrogen flux and fabricability. Vanadium was chosen as a compromise between performance and cost. It is clear that the vanadium alloys for this application can be produced, but the approach is not simple and the results inconsistent. For any future contracts, large single batches of alloy would be obtained and rolled with larger facilities to produce the most consistent thin foils possible. Brazing was identified as a very likely choice for sealing the membranes to structural components. As alloying was beneficial to hydrogen transport, it became important to identify where those alloying elements might be detrimental to brazing. Cataloging positive and negative alloying effects was a significant portion of the initial project work on vanadium alloying. A water gas shift catalyst with ceramic like structural characteristics was the second large goal of the project. Alumina was added as a component of conventional high temperature water gas shift iron oxide based catalysts. The catalysts contained Fe-Al-Cr-Cu-O and were synthesized by co-precipitation. A series of catalysts were prepared with 5 to 50 wt% Al2O3, with 8 wt% Cr2O3, 4 wt% CuO, and the balance Fe2O3. All of the catalysts were compared to a reference WGS catalyst (88 wt% FeOx, 8 wt% Cr2O3, and 4 wt% CuO) with no alumina. Alumina addition to conventional high temperature water gas shift catalysts at concentrations of approximately 15 wt% increased CO conversion rates and increase thermal stability. A series of high temperature water gas shift catalysts containing iron, chromia, and copper oxides were prepared with small amounts of added ceria in the system Fe-Cr-Cu-Ce-O. The catalysts were also tested kinetically under WGS conditions. 2-4 wt% ceria addition (at the expense of the iron oxide content) resulted in increased reaction rates (from 22-32% higher) compared to the reference catalyst. The project goal of a 10,000 liter per day WGS-membrane reactor was achieved by a device operating on coal derived syngas containing significant amounts of carbon monoxide and hydrogen sulfide. The membrane flux was equivalent to 52 scfh/ft2 based on a 600 psi syngas inlet pressure and corresponded to membranes costing $191 per square foot. Over 40 hours of iv exposure time to syngas has been achieved for a double membrane reactor. Two modules of the Chart reactor were tested under coal syngas for over 75 hours with a single module tested for 50 hours. The permeance values for the Chart membranes were similar to the REB reactor though total flux was reduced due to significantly thicker membranes. Overall testing of membrane reactors on coal derived syngas was over 115 hours for all reactors tested. Testing of the REB double membrane device exceeded 40 hours. Performance of the double membrane reactor has been similar to the results for the single reactor with good maintenance of flux even after these long exposures to hydrogen sulfide. Of special interest is that the flux is highest at the start of each experiment as predicted, but unusually, the flux returns to higher values after exposures to air as short as 20 seconds. The assumption from these findings is that absorbed carbon monoxide, sulfur, or both are removed by exposure of the membranes to oxygen at 400ºC. This is a good sign that indicates that membranes affected by absorbed species can be recovered, and will require some thought to process design to allow for recovery steps during scaled operations of hydrogen production. An important characteristic in the data is the return to a higher flux level after each new exposure to air at temperature. This indicates that the membrane reactor may be subject to refreshment of the surface during operation.

02 PETROLEUM↗

Development of Directed Energy Deposited NASA HR-1 to Optimize Properties for Liquid Rocket Engine Applications

Metal additive manufacturing (AM) processes have been demonstrated to be effective at reducing costs and lead times associated with fabrication of complex propulsion component designs. Laser powder directed energy deposition (LP-DED) and laser powder bed fusion (L-PBF) are metal AM technologies that have effectively been used to produce a variety of parts for space applications. These technologies have enabled new designs and materials for these applications. The National Aeronautics and Space Administration (NASA) has identified the need to develop and advance new materials in unique space applications such as high-pressure hydrogen environments. One such metal alloy being developed for these applications is NASA HR-1. A high-strength Fe-Ni based superalloy, NASA HR-1 was designed to resist high pressure hydrogen environment embrittlement, oxidation, and corrosion. AM technologies have enabled the manufacturing of NASA HR-1 to be a feasible material for components in hydrogen environments. Development efforts for NASA HR-1 have completed build and heat treatment optimization, material characterization, thermophysical property testing, and mechanical testing in air and hydrogen environments to mature the understanding of the material. This poster will summarize the development of NASA HR-1 for AM including composition and heat treatment optimization, microstructure characterization, and results of mechanical testing in air and high pressure hydrogen.

NASA HR-1↗

Development and Optimization of Additively Manufactured NASA HR-1 for Space Applications

Metal additive manufacturing (AM) processes have been demonstrated to be effective at reducing costs and lead times associated with fabrication of complex propulsion component designs. Laser powder directed energy deposition (LP-DED) and laser powder bed fusion (L-PBF) are metal AM technologies that have effectively been used to produce a variety of parts for space applications. These technologies have enabled new designs and materials for these applications. The National Aeronautics and Space Administration (NASA) has identified the need to develop and advance new materials in unique space applications such as high-pressure hydrogen environments. One such metal alloy being developed for these applications is NASA HR-1. A high-strength Fe-Ni based superalloy, NASA HR-1 was designed to resist high pressure hydrogen environment embrittlement, oxidation, and corrosion. AM technologies have enabled the manufacturing of NASA HR-1 to be a feasible material for components in hydrogen environments. Development efforts for NASA HR-1 have completed build and heat treatment optimization, material characterization, thermophysical property testing, and mechanical testing in air and hydrogen environments to mature the understanding of the material. This presentation will summarize the development of NASA HR-1 for AM including composition and heat treatment optimization, microstructure characterization, and results of mechanical testing in air and high pressure hydrogen.

Additive Manufacturing↗

Updated Filter Leak Frequencies for Use in Risk Assessments

Quantitative risk assessment (QRA) is highly dependent on data, leading to more robust models as new and updated data is acquired. The Hydrogen Plus Other Alternative Fuels Risk Assessment (HyRAM+) QRA capabilities include calculations of individual risk from leaks in a gaseous hydrogen facility due to the potential effects of jet fires and explosions. Leak frequencies are acquired through statistical analysis of published data from a variety of sources and industries. The filter leak frequencies in previous versions of the HyRAM+ software are substantially greater than the leak frequencies of other components, leading to QRA results for gaseous hydrogen in which filters consistently dominate the overall risk. Data that were previously used to derive the filter leak frequencies were reevaluated for applicability and additional data points were added to update the filter leak frequencies. The new frequencies are more comparable to leak frequencies for other components.

08 HYDROGEN↗

Performance and Durability of Pure-Water-Fed Anion Exchange Membrane Electrolyzers Using Baseline Materials and Operation

Water electrolysis powered by renewable electricity produces green hydrogen and oxygen gas, which can be used for energy, fertilizer, and industrial applications and thus displace fossil fuels. Pure-water anion-exchange-membrane (AEM) electrolyzers in principle offer the advantages of commercialized proton-exchange-membrane systems (high current density, low cross over, output gas compression, etc.) while enabling the use of less-expensive steel components and nonprecious metal catalysts. AEM electrolyzer research and development, however, has been limited by the lack of broadly accessible materials that provide consistent cell performance, making it difficult to compare results across studies. Further, even when the same materials are used, different pretreatments and electrochemical analysis techniques can produce different results. Here, we report an AEM electrolyzer comprising commercially available catalysts, membrane, ionomer, and gas-diffusion layers operating near 1.9 V at 1 A cm –2 in pure water. After the initial break in, the performance degraded by 0.67 mV h –1 at 0.5 A cm –2 at 55 °C. We detail the key preparation, assembly, and operation techniques employed and show further performance improvements using advanced materials as a proof-of-concept for future AEM-electrolyzer development. Here, the data thus provide an easily reproducible and comparatively high-performance baseline that can be used by other laboratories to calibrate the performance of improved cell components, nonprecious metal oxygen evolution, and hydrogen evolution catalysts and learn how to mitigate degradation pathways.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Modeling Results For the ITER Cryogenic Fore Pump (Final Report)

A numerical model characterizing the operation of a cryogenic fore-pump (CFP) for ITER has been developed at the University of Wisconsin – Madison during the period from March 15, 2011 through June 30, 2014. The purpose of the ITER-CFP is to separate hydrogen isotopes from helium gas, both making up the exhaust components from the ITER reactor. The model explicitly determines the amount of hydrogen that is captured by the supercritical-helium-cooled pump as a function of the inlet temperature of the supercritical helium, its flow rate, and the inlet conditions of the hydrogen gas flow. Furthermore the model computes the location and amount of hydrogen captured in the pump as a function of time. Throughout the model’s development, and as a calibration check for its results, it has been extensively compared with the measurements of a CFP prototype tested at Oak Ridge National Lab. The results of the model demonstrate that the quantity of captured hydrogen is very sensitive to the inlet temperature of the helium coolant on the outside of the cryopump. Furthermore, the model can be utilized to refine those tests, and suggests methods that could be incorporated in the testing to enhance the usefulness of the measured data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Booster engines derived from the Space Shuttle Main Engine

Current vehicle studies of post-Space Shuttle vehicles have identified the potential need for a high-pressure booster engine using liquid oxygen/hydrocarbon fuel (RP-1) as propellants. Recent studies of the possibility of using Space Shuttle Main Engine (SSME) components for a high pressure LOX/RP-1 engine have resulted in several engine configurations which are based largely on SSME components. The current SSME thrust chamber is regeneratively cooled with hydrogen using a relatively low percentage of the total hydrogen flow. For a LOX/RP-1 application the SSME thrust chamber can be run at high pressures and be cooled with a relatively low hydrogen flow. In addition, the SSME oxygen pump, valves, and main injector components may be utilized for the booster engine. By using a majority of the current SSME engine components for the LOX/RE-1 booster engine, engine development time and cost can be significantly reduced compared to the development of a new engine.

Sobin, A. J.↗

Systems Engineering of Chemical Hydrogen Storage, Pressure Vessel and Balance of Plant for Onboard Hydrogen Storage

This is the annual report for the Hydrogen Storage Engineering Center of Excellence project as required by DOE EERE's Fuel Cell Technologies Office. We have been provided with a specific format. It describes the work that was done with cryo-sorbent based and chemical-based hydrogen storage materials. Balance of plant components were developed, proof-of-concept testing performed, system costs estimated, and transient models validated as part of this work.

balance of plant↗

H{sub α} SPECTRAL DIVERSITY OF TYPE II SUPERNOVAE: CORRELATIONS WITH PHOTOMETRIC PROPERTIES

We present a spectroscopic analysis of the H{sub α} profiles of hydrogen-rich Type II supernovae. A total of 52 Type II supernovae having well-sampled optical light curves and spectral sequences were analyzed. Concentrating on the H{sub α} P-Cygni profile we measure its velocity from the FWHM of the emission and the ratio of absorption to emission (a/e) at a common epoch at the start of the recombination phase, and search for correlations between these spectral parameters and photometric properties of the V-band light curves. Testing the strength of various correlations we find that a/e appears to be the dominant spectral parameter in terms of describing the diversity in our measured supernova properties. It is found that supernovae with smaller a/e have higher H{sub α} velocities, more rapidly declining light curves from maximum during the plateau and radioactive tail phase, are brighter at maximum light, and have shorter optically thick phase durations. We discuss possible explanations of these results in terms of physical properties of Type II supernovae, speculating that the most likely parameters that influence the morphologies of H{sub α} profiles are the mass and density profile of the hydrogen envelope, together with additional emission components due to circumstellar interaction.

79 ASTRONOMY AND ASTROPHYSICS↗

Flow-Control Unit For Nitrogen And Hydrogen Gases

Gas-flow-control unit installed and removed as one piece replaces system that included nine separately serviced components. Unit controls and monitors flows of nitrogen and hydrogen gases. Designed for connection via fluid-interface manifold plate, reducing number of mechanical fluid-interface connections from 18 to 1. Unit provides increasing reliability, safety, and ease of maintenance, and for reducing weight, volume, and power consumption.

Chang, B. J.↗

Performance, reliability and life issues for components of the Planck Sorption Cooler

Continuous-duty hydrogen sorption cryocoolers are being developed for the European Space Agency (ESA) Planck mission. To achieve an acceptable level of performance and robust operation with these hydride refrigerators during flight, detailed investigations have been performed on the sorbent materials and on critical hardware components.

sorption↗