Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “height estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

An Examination of the Effect of Boundary Layer Ingestion on Turboelectric Distributed Propulsion Systems

A Turboelectric Distributed Propulsion (TeDP) system differs from other propulsion systems by the use of electrical power to transmit power from the turbine to the fan. Electrical power can be efficiently transmitted over longer distances and with complex topologies. Also the use of power inverters allows the generator and motors speeds to be independent of one another. This decoupling allows the aircraft designer to place the core engines and the fans in locations most advantageous for each. The result can be very different installation environments for the different devices. Thus the installation effects on this system can be quite different than conventional turbofans where the fan and core both see the same installed environments. This paper examines a propulsion system consisting of two superconducting generators, each driven by a turboshaft engine located so that their inlets ingest freestream air, superconducting electrical transmission lines, and an array of superconducting motor driven fan positioned across the upper/rear fuselage area of a hybrid wing body aircraft in a continuous nacelle that ingests all of the upper fuselage boundary layer. The effect of ingesting the boundary layer on the design of the system with a range of design pressure ratios is examined. Also the impact of ingesting the boundary layer on off-design performance is examined. The results show that when examining different design fan pressure ratios it is important to recalculate of the boundary layer mass-average Pt and MN up the height for each inlet height during convergence of the design point for each fan design pressure ratio examined. Correct estimation of off-design performance is dependent on the height of the column of air measured from the aircraft surface immediately prior to any external diffusion that will flow through the fan propulsors. The mass-averaged Pt and MN calculated for this column of air determine the Pt and MN seen by the propulsor inlet. Since the height of this column will change as the amount of air passing through the fans change as the propulsion system is throttled, and since the mass-average Pt and MN varies by height, this capture height must be recalculated as the airflow through the propulsor is varied as the off-design performance point is converged.

Felder, James L.↗
NASA NTRS2014

Comparison of GEOS-5 AGCM Planetary Boundary Layer Depths Computed with Various Definitions

Accurate models of planetary boundary layer (PBL) processes are important for forecasting weather and climate. The present study compares seven methods of calculating PBL depth in the GEOS-5 atmospheric general circulation model (AGCM) over land. These methods depend on the eddy diffusion coefficients, bulk and local Richardson numbers, and the turbulent kinetic energy. The computed PBL depths are aggregated to the Koppen climate classes, and some limited comparisons are made using radiosonde profiles. Most methods produce similar midday PBL depths, although in the warm, moist climate classes, the bulk Richardson number method gives midday results that are lower than those given by the eddy diffusion coefficient methods. Additional analysis revealed that methods sensitive to turbulence driven by radiative cooling produce greater PBL depths, this effect being most significant during the evening transition. Nocturnal PBLs based on Richardson number are generally shallower than eddy diffusion coefficient based estimates. The bulk Richardson number estimate is recommended as the PBL height to inform the choice of the turbulent length scale, based on the similarity to other methods during the day, and the improved nighttime behavior.

AGCM↗
NASA NTRS2013

Antarctica, Greenland and Gulf of Alaska Land-ice Evolution from an Iterated GRACE Global Mascon Solution

We have determined the ice mass evolution of the Antarctica and Greenland ice sheets (AIS and GIS) and Gulf of Alaska (GOA) glaciers from a new GRACE global solution of equal-area surface mass concentration parcels (mascons) in equivalent height of water. The mascons were estimated directly from the reduction of the inter-satellite K-band range-rate (KBRR) observations, taking into account the full noise covariance, and formally iterating the solution. The new solution increases signal recovery while reducing the GRACE KBRR observation residuals. The mascons were estimated with 10 day and 1 arc degree equal-area sampling, applying anisotropic constraints. An ensemble empirical mode decomposition adaptive filter was applied to the mascon time series to compute annual mass balances. The details and causes of the spatial and temporal variability of the land-ice regions studied are discussed. The estimated mass trend over the total GIS, AIS and GOA glaciers for the time period 1 December 2003 to 1 December 2010 is -380 plus or minus 31 Gt a(exp -1), equivalent to -1.05 plus or minus 0.09 mma(exp -1) sea-level rise. Over the same time period we estimate the mass acceleration to be -41 plus or minus 27 Gt a(exp -2), equivalent to a 0.11 plus or minus 0.08 mm a(exp -2) rate of change in sea level. The trends and accelerations are dependent on significant seasonal and annual balance anomalies.

MASCON↗
NASA NTRS2014

Remote Sensing of Cloud Top Height from SEVIRI: Analysis of Eleven Current Retrieval Algorithms

The role of clouds remains the largest uncertainty in climate projections. They influence solar and thermal radiative transfer and the earth's water cycle. Therefore, there is an urgent need for accurate cloud observations to validate climate models and to monitor climate change. Passive satellite imagers measuring radiation at visible to thermal infrared (IR) wavelengths provide a wealth of information on cloud properties. Among others, the cloud top height (CTH) - a crucial parameter to estimate the thermal cloud radiative forcing - can be retrieved. In this paper we investigate the skill of ten current retrieval algorithms to estimate the CTH using observations from the Spinning Enhanced Visible and InfraRed Imager (SEVIRI) onboard Meteosat Second Generation (MSG). In the first part we compare ten SEVIRI cloud top pressure (CTP) data sets with each other. The SEVIRI algorithms catch the latitudinal variation of the CTP in a similar way. The agreement is better in the extratropics than in the tropics. In the tropics multi-layer clouds and thin cirrus layers complicate the CTP retrieval, whereas a good agreement among the algorithms is found for trade wind cumulus, marine stratocumulus and the optically thick cores of the deep convective system. In the second part of the paper the SEVIRI retrievals are compared to CTH observations from the Cloud-Aerosol LIdar with Orthogonal Polarization (CALIOP) and Cloud Profiling Radar (CPR) instruments. It is important to note that the different measurement techniques cause differences in the retrieved CTH data. SEVIRI measures a radiatively effective CTH, while the CTH of the active instruments is derived from the return time of the emitted radar or lidar signal. Therefore, some systematic differences are expected. On average the CTHs detected by the SEVIRI algorithms are 1.0 to 2.5 kilometers lower than CALIOP observations, and the correlation coefficients between the SEVIRI and the CALIOP data sets range between 0.77 and 0.90. The average CTHs derived by the SEVIRI algorithms are closer to the CPR measurements than to CALIOP measurements. The biases between SEVIRI and CPR retrievals range from −0.8 kilometers to 0.6 kilometers. The correlation coefficients of CPR and SEVIRI observations vary between 0.82 and 0.89. To discuss the origin of the CTH deviation, we investigate three cloud categories: optically thin and thick single layer as well as multi-layer clouds. For optically thick clouds the correlation coefficients between the SEVIRI and the reference data sets are usually above 0.95. For optically thin single layer clouds the correlation coefficients are still above 0.92. For this cloud category the SEVIRI algorithms yield CTHs that are lower than CALIOP and similar to CPR observations. Most challenging are the multi-layer clouds, where the correlation coefficients are for most algorithms between 0.6 and 0.8. Finally, we evaluate the performance of the SEVIRI retrievals for boundary layer clouds. While the CTH retrieval for this cloud type is relatively accurate, there are still considerable differences between the algorithms. These are related to the uncertainties and limited vertical resolution of the assumed temperature profiles in combination with the presence of temperature inversions, which lead to ambiguities in the CTH retrieval. Alternative approaches for the CTH retrieval of low clouds are discussed.

Hamann, U.↗
NASA NTRS2021

ICESat-2 Early Mission Synopsis and Observatory Performance

The Advanced Topographic Laser Altimetry System (ATLAS) onboard the NASA Ice, Cloud and land Elevation Satellite-2 (ICESat-2) is the newest and most recent Earth observing satellite for global elevation studies. The primary objectives for ICESat-2 follow that of its predecessor, ICESat, and focus on providing cryospheric measurements to determine ice sheet mass balance, and monitor both sea ice thickness and extent. However, the global observations support secondary science objectives such as biomass estimation, inland water elevation, sea state height and aerosol concentrations. In all, ATLAS measurements support 7 along-track geophysical products with multiple gridded products to provide regional and global change detection for seasonal and annual cycles. Since the launch of ICESat-2, the instrument has operated nominally and collected more than a trillion measurements. This paper provides an overview of the mission, a description of the operational components that support the altimeter products for science discovery and on-orbit observatory performance.

Lori Magruder↗
NASA NTRS2018

Satellite Remote Sensing Estimation of River Discharge: Application to the Yukon River Alaska

A methodology based on general hydraulic relations for rivers has been developed to estimate the discharge (flow rate) of rivers using satellite remote sensing observations. The estimates of discharge, flow depth, and flow velocity are derived from remotely observed water surface area, water surface slope, and water surface height, and demonstrated for two reaches of the Yukon River in Alaska, at Eagle (reach length 34.7 km) and near Stevens Village (reach length 38.3 km). The method is based on fundamental equations of hydraulic flow resistance in rivers, including the Manning equation and the Prandtl-von Karman universal velocity distribution equation. The method employs some new hydraulic relations to help define flow resistance and height of the zero flow boundary in the channel. Estimates are made both with and without calibration. The water surface area of the river reach is measured by using a provisional version of the U.S. Geological Survey (USGS) Landsat based product named Dynamic Surface Water Extent (DSWE). The water surface height and slope measurements require a self-consistent datum, and are derived from observations from the Jason-2 satellite altimeter mission. At both reach locations, the Jason-2 radar altimeter non-winter heights consistently tracked the stage recorded at USGS streamgages with a standard deviation of differences (error) during the non-winter periods of less than 7%. Part of the error may be due to differences in the gage and altimeter crossing locations with respect to the range of stage change and the response to changes in discharge at the upstream and downstream locations. For the non-winter periods, the radar derived slope estimates (mean = 0.0003) were constant over the mission lifetime, and in agreement with previously measured USGS water surface slopes and slopes determined from USGS topographic maps. The accuracy of the mean of the uncalibrated daily estimates of discharge varied between reaches, ranging from 13% near Stevens Village (N = 90) to −21% at Eagle (N = 246) based on the absolute error, and 5% to −6% based on the error of the log of the estimates. Calibrating to the mean of USGS daily discharge estimates from the streamflow rating for the same period of record at each streamgage resulted in mean absolute errors ranging from 1% to 2%, and log errors ranging from 1% or less. The error pattern of the estimates shows that without calibration, even though the mean is well simulated, the high and low end values over the range of estimates may have significant bias.

Bjerklie, David M.↗
NASA NTRS1995

Structure and dynamics of coronal plasmas

The Normal Incidence X-ray Telescope (NIXT) obtained a unique set of high resolution full disk solar images which were exposed simultaneously by X-rays in a passband at 63.5 A and by visible light. The perfect alignment of a photospheric visible light image with a coronal X-ray image enables us to present observations of X-ray intensity vs an accurately determined height above the visible limb. The height at which the observed X-ray intensity peak varies from 4000 km in active regions to 9000 km in quiet regions of the sun. The interpretation of the observations stems from the previously established fact that, for the coronal loops, emission in the NIXT bandpass peaks sharply just above the footpoints. Because there is not a sharp peak in the observed X-ray intensity vs off limb height, we conclude that the loop footpoints, when viewed at the limb, are obscured by absorption in chromospheric material along the line of sight. We calculate the X-ray intensity vs height predicted by a number of different idealizations of the solar atmosphere, and we compare these calculations with the observed X-ray intensity vs height. The calculations use existing coronal and chromospheric models. In order for the calculations to reproduce the observed off limb X-ray intensities, we are forced to assume an atmosphere in which the footpoints of coronal loops are interspersed along the line of sight with cooler chromospheric material extending to heights well above the loop footpoints. We argue that the absorption coefficient for NIXT X-rays by chromospheric material is roughly proportional to the neutral hydrogen density, and we estimate an average neutral hydrogen density and scale height implied by the data.

Golub, Leon↗
NASA NTRS2022

Using Atmospheric Trace Gas Vertical Profiles to Evaluate Model Fluxes: A Case Study of Arctic-Cap Observations and Geos Simulations for the ABoVE Domain

Accurate estimates of carbon–climate feedbacks require an independent means for evaluating surface flux models at regional scales. The altitude-integrated enhancement (AIE) derived from the Arctic Carbon Atmospheric Profiles (Arctic-CAP) project demonstrates the utility of this bulk quantity for surface flux model evaluation. This bulk quantity leverages background mole fraction values from the middle free troposphere, is agnostic to uncertainties in boundary layer height, and can be derived from model estimates of mole fractions and vertical gradients. To demonstrate the utility of the bulk quantity, six airborne profiling surveys of atmospheric carbon dioxide (CO2), methane (CH4), and carbon monoxide (CO) throughout Alaska and northwestern Canada between April and November 2017 were completed as part of NASA’s Arctic–Boreal Vulnerability Experiment (ABoVE). The Arctic-CAP sampling strategy involved acquiring vertical profiles of CO2, CH4, and CO from the surface to 5 km altitude at 25 sites around the ABoVE domain on a 4- to 6-week time interval. All Arctic-CAP measurements were compared to a global simulation using the Goddard Earth Observing System (GEOS) modeling system. Comparisons of the AIE bulk quantity from aircraft observations and GEOS simulations of atmospheric CO2, CH4, and CO highlight the fidelity of the modeled surface fluxes. The model–data comparison over the ABoVE domain reveals that while current state-of-the-art models and flux estimates are able to capture broad-scale spatial and temporal patterns in near-surface CO2 and CH4 concentrations, more work is needed to resolve fine-scale flux features that are captured in CO observations

CO2↗
NASA NTRS1990

The estimation of convective rainfall by area integrals. I - The theoretical and empirical basis. II - The height-area rainfall threshold (HART) method

A theory is developed which establishes the basis for the use of rainfall areas within present thresholds as a measure of either the instantaneous areawide rain rate of convective storms or the total volume of rain from an individual storm over its lifetime. The method is based upon the existence of a well-behaved pdf of rain rate either from the many storms at one instant or from a single storm during its life. The generality of the instantaneous areawide method was examined by applying it to quantitative radar data sets from the GARP Tropical Atlantic Experiment for South Africa, Texas, and Darwin (Australia). It is shown that the pdf's developed for each of these areas are consistent with the theory.

Rosenfeld, Daniel↗
NASA NTRS1987

Earth science research

The analysis of ground-truth data from the boreal forest plots in the Superior National Forest, Minnesota, was completed. Development of statistical methods was completed for dimension analysis (equations to estimate the biomass of trees from measurements of diameter and height). The dimension-analysis equations were applied to the data obtained from ground-truth plots, to estimate the biomass. Classification and analyses of remote sensing images of the Superior National Forest were done as a test of the technique to determine forest biomass and ecological state by remote sensing. Data was archived on diskette and tape and transferred to UCSB to be used in subsequent research.

Botkin, Daniel B.↗
DOE OSTI2021

An Automated Method for Mapping Giant Kelp Canopy Dynamics from UAV

Satellite and aerial imagery have been used extensively for mapping the abundance and distribution of giant kelp ( Macrocystis pyrifera ) in southern California. There is now great potential for using unoccupied aerial vehicles (UAVs) to map kelp canopy at very high resolutions. However, tides and currents have been shown to affect the amount of floating kelp canopy on the water surface, and the impacts of these processes on remotely sensed kelp estimates in this region have not been fully quantified. UAVs were used to map fine-scale changes in canopy area due to tidal height and current speed at kelp forests off the coast of Palos Verdes, CA and Santa Barbara, CA. An automated method for detecting kelp canopy was developed that was 67% accurate using red-green-blue (RGB) UAV imagery and 93% accurate using multispectral UAV imagery across a range of weather, ocean, and illumination conditions. Increases in tidal height of 1 m reduced the amount of floating kelp canopy by 15% in Santa Barbara and by over 30% in Palos Verdes. The effect of current speed on visible kelp canopy was inconclusive, but there was a trend towards lower canopy area with increased current speed. Therefore, while tidal height and current speed can introduce significant variability to estimates of kelp abundance, the magnitude of this variability is site specific. Still, UAVs are a valuable tool for mapping of kelp canopy and can provide greater spatial resolution and temporal coverage than is possible from many satellite sensors. This data can provide insight into the patterns and drivers of high frequency fluctuations in kelp abundance.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Aerosol impacts on isolated deep convection: findings from TRACER

This study focuses on quantifying the conditional relationship between aerosol and convective precipitation properties of isolated deep convective clouds (DCCs) in the Houston–Galveston region, after adjusting for confounding effects. We leverage comprehensive ground-based observations from the TRacking Aerosol Convection interactions ExpeRiment (TRACER) to estimate aerosol effects on convective echo top height (ETH), intensity, and area separately. Our results show that greater aerosol number concentrations generally have a limited impact on these convective properties, showing relationships consistent with the possibility of both invigoration and suppression effects. Under certain conditions, where ultrafine particles are abundant, aerosols exhibit a positive effect on ETH, increasing it by about 1 km. However, it is inevitable to consider measurement uncertainties and the limitations of temporal and spatial resolution in the data, as these factors can further contribute to uncertainties in our estimates. In DCCs associated with sea breezes, the estimated aerosol effects on DCCs are found to be more pronounced. However, this heightened effect could be attributed to the exclusion of key confounders such as boundary layer updrafts in the analysis.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1994

Preliminary estimates of Gulf Stream characteristics from TOPEX data and a precise gravimetric geoid

TOPEX sea surface height data has been used, with a gravimetric geoid, to calculate sea surface topography across the Gulf Stream. This topography was initially computed for nine tracks on cycles 21 to 29. Due to inaccurate geoid undulations on one track, results for eight tracks are reported. The sea surface topography estimates were used to calculate parameters that describe Gulf Stream characteristics from two models of the Gulf Stream. One model was based on a Gaussian representation of the velocity while the other was a hyperbolic representation of velocity or the sea surface topography. The parameters of the Gaussian velocity model fit were a width parameter, a maximum velocity value, and the location of the maximum velocity. The parameters of the hyperbolic sea surface topography model were the width, the height jump, position, and sea surface topography at the center of the stream. Both models were used for the eight tracks and nine cycles studied. Comparisons were made between the width parameters, the maximum velocities, and the height jumps. Some of the parameter estimates were found to be highly (0.9) correlated when the hyperbolic sea surface topography fit was carried out, but such correlations were reduced for either the Gaussian velocity fits or the hyperbolic velocity model fit. A comparison of the parameters derived from 1-year TOPEX data showed good agreement with values derived by Kelly (1991) using 2.5 years of Geosat data near 38 deg N, 66 deg W longitude. Accuracy of the geoid undulations used in the calculations was of order of +/- 16 cm with the accuracy of a geoid undulation difference equal to +/- 15 cm over a 100-km line in areas with good terrestrial data coverage. This paper demonstrates that our knowledge or geoid undulations and undulation differences, in a portion of the Gulf Stream region, is sufficiently accurate to determine characteristics of the jet when used with TOPEX altimeter data. The method used here has not been shown to be more accurate than methods that average altimeter data to form a reference surface used in analysis to obtain the Gulf Stream characteristics. However, the results show the geoid approach may be used in areas where lack of current meandering reduces the accuracy of the average surface procedure.

Rapp, Richard H.↗
NASA NTRS1990

A preliminary estimate of geoid-induced variations in repeat orbit satellite altimeter observations

Altimeter satellites are often maintained in a repeating orbit to facilitate the separation of sea-height variations from the geoid. However, atmospheric drag and solar radiation pressure cause a satellite orbit to drift. For Geosat this drift causes the ground track to vary by + or - 1 km about the nominal repeat path. This misalignment leads to an error in the estimates of sea surface height variations because of the local slope in the geoid. This error has been estimated globally for the Geosat Exact Repeat Mission using a mean sea surface constructed from Geos 3 and Seasat altimeter data. Over most of the ocean the geoid gradient is small, and the repeat-track misalignment leads to errors of only 1 to 2 cm. However, in the vicinity of trenches, continental shelves, islands, and seamounts, errors can exceed 20 cm. The estimated error is compared with direct estimates from Geosat altimetry, and a strong correlation is found in the vicinity of the Tonga and Aleutian trenches. This correlation increases as the orbit error is reduced because of the increased signal-to-noise ratio.

Brenner, Anita C.↗
NASA NTRS1985

Modeling gravity and magnetic fields for crustal and upper mantle structures

Research was conducted to: (1) make a direct comparison between the gravity and magnetic fields near the ellipsoid and at the height expected for the Geopotential Research Mission (GRM) for the same geologic model, (2) obtain realistic estimates of the gradients that can be expected at the orbit height of the GRM, and (3) demonstrate the value of data that the GRM could provide for investigating upper mantle and deep crustal anomalies.

Denoyer, J. M.↗
NASA NTRS1992

Effect of the geomagnetic field on the diffusion of meteor trains

A solution to the problem of the diffusion of a meteor train in the geomagnetic field from an initial line density may be written in closed form in terms of effective diffusion coefficients depending on direction, enabling detailed calculations across the entire range of angle of train to field and relevant heights. While the effective diffusion coefficient in the plane of train and field then remains close to the zero field ambipolar value right up to 90 deg, the effective coefficient in the direction of the normal to plane of train and field drops steadily to its theta = 0 value at theta = 90 deg. At 95 km this corresponds to a change of almost 5 km, in 'diffusion height', that is, the height of an underdense meteor calculated on the basis of the exponential decay of its radar echo. We have estimated the consequent changes in the expected distribution of diffusion heights for various orientations of radar antenna and find the dependence on azimuth is very marked. The effect of the field is relatively minor for a south pointing beam but very strong if the beam is pointing north.

Jones, William↗
DOE OSTI2020

SCOPE: Spectral cloud optical property estimation using real-time GOES-R longwave imagery

The output of ground-based, solar power generation systems is strongly dependent on cloud cover, which is the main contributor to solar power variability and uncertainty. Cloud optical properties are typically over-simplified in forecasting applications due to the lack of realtime, accurate estimates. In this work, we introduce a method, the Spectral Cloud Optical Property Estimation (SCOPE), for estimating cloud optical properties directly from high-resolution (5-min, 2 km) imagery from Geostationary Operational Environmental Satellite (GOES)-R, which is the newest generation of the GOES system. The SCOPE method couples a two-stream, spectrally resolved radiative model with the longwave GOES-R sensor output to simultaneously estimate the cloud optical depth, cloud top height, and cloud thickness during both day and night at 5-min intervals. The accuracy of SCOPE is evaluated using one year (2018) of downwelling longwave (DLW) radiation measurements from the Surface Radiation Budget Network, which consists of seven sites spread across climatically diverse regions of the contiguous United States. During daytime clear-sky periods, SCOPE predicts DLW within instrument uncertainty (10 W m -2 ) for four of the seven locations, with the remaining locations yielding errors of the order of 11.2, 17.7, and 20.2 W m -2 . For daytime cloudy-sky, daytime all-sky (clear or cloudy), and nighttime all-sky periods, SCOPE achieves root mean square error values of 23.0–34.5 W m -2 for all seven locations. These results, together with the low-latency of the method (1 s per sample), show that SCOPE provides a viable solution to real-time, accurate estimation of cloud optical properties for both day and night.

42 ENGINEERING↗
NASA NTRS1990

The 27-28 October 1986 FIRE IFO cirrus case study - Cloud parameter fields derived from satellite data

A cirrus parameter retrieval methodology and the results of its application over the cirrus Intensive Field Observation (IFO) area using data from the Geostationary Operational Environmental Satellite (GOES) taken during the FIRE cirrus case study days, October 27-28, 1986. An impirical cloud bidirectional reflectance model derived from another IFO analysis was combined with a theoretical ice crystal cloud albedo model to estimate visible cloud optical thickness, which was used to derive the cloud infrared emittance. Cloud altitude was adjusted based on the derived emittance and observed temperatures. The approach developed here produced a very reasonable picture of cirrus cloud fields. It was estimated that the cloud-top and cloud-center heights are derived with a precision of about 0.6 km, except in very broken cloud conditions. Cirrus cloud thicknesses were also estimated and it is found that the derived results are comparable to other case study observations.

Minnis, Patrick↗