Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “full-scale measurements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Update of the Solar Concentrator Advanced Development Project

The Solar Concentrator Advanced Development Project, which has achieved the successful design, fabrication, and testing of a full-scale prototypical solar dynamic concentrator, is discussed. The design and fabrication process are summarized, and the test results for the reflective facet optical performance and the concentrator structural repeatability are reported. Initial testing of structural repeatability of a seven panel portion of the concentrator was followed by assembly and testing of the full nineteen-panel structure. The testing, which consisted of theodolite and optical measurements over an assembly-disassembly-reassembly cycle, demonstrated that the concentrator maintained the as-built contour and optical characteristics. The facet development effort, which entailed developing a vapor-deposited reflective facet, produced a viable design with demonstrated optical characteristics that are within the project goals.

Corrigan, Robert D.↗
NASA NTRS1991

Inflight source noise of an advanced full-scale single-rotation propeller

Flight tests to define the far field tone source at cruise conditions were completed on the full scale SR-7L advanced turboprop which was installed on the left wing of a Gulfstream II aircraft. This program, designated Propfan Test Assessment (PTA), involved aeroacoustic testing of the propeller over a range of test conditions. These measurements defined source levels for input into long distance propagation models to predict en route noise. Inflight data were taken for 7 test cases. The sideline directivities measured by the Learjet showed expected maximum levels near 105 degrees from the propeller upstream axis. However, azimuthal directivities based on the maximum observed sideline tone levels showed highest levels below the aircraft. An investigation of the effect of propeller tip speed showed that the tone level of reduction associated with reductions in propeller tip speed is more significant in the horizontal plane than below the aircraft.

Woodward, Richard P.↗
NASA NTRS1991

Experimental investigation of the flow field in the head-end star slot section of a solid rocket motor

A test program has been developed to investigate the complex flowfield in the head-end, star grain section of a solid rocket motor. Documentation of the flowfield pattern is to be obtained using both flow visualization techniques and quantitative methods, including static pressure measurements, heat transfer coefficient measurements, and hot-wire anemometry. A cold-flow, one-tenth-scale model based on the geometry of the Space Shuttle SRM head-end section and its single-port igniter, along with two models of a four-port igniter, have been constructed. The scale factor is derived from a scaling analysis which matches Reynolds number between the model and the full-scale flowfield in the star grain section. The NASA Marshall Space Flight Center 14 x 14 inch trisonic wind tunnel will be utilized for the cold flow tests. Since the work is still in progress, no results are included.

Ciucci, A.↗
NASA NTRS1992

Aerodynamic roughness measured in the field and simulated in a wind tunnel

This study evaluates how well values of aerodynamic surface roughness, z sub 0, measured over scale models in wind tunnels correlate with values of z sub 0 measured at full scale in the field. A field experiment was conducted in which values of z sub 0 and u* (wind friction speed) were measured over three arrays of non-erodible roughness elements on a dry lake bed. Wind profiles were measured by ten anemometers on a 15 m mast under thermally neutral atmospheric conditions. Values of z sub 0 increased from .00014 m (dry lake bed only) to .026 m with increasing roughness element density. The three roughness element arrays were simulated at 1/10 and 1/20 scale in an open-circuit atmospheric boundary-layer wind tunnel. Velocities were measured with a boundary-layer pitot-tube rake from the same relative position within the scale model arrays as the anemometers were relative to the field arrays. Each array at each scale was sampled three times at five freestream velocities. Average values of z sub 0 for each model array at each scale were compared with full-scale values of z sub 0 obtained in the field. The field vs. wind tunnel correspondence of z sub 0 is found to be z sub 0 field = 0.2661 x (z sub(0 model) x scale(exp -1))exp .8159.

Sullivan, Robert↗
NASA NTRS1992

Full-scale high angle-of-attack tests of an F/A-18

This paper presents an overview of high angle-of-attack tests of a full-scale F/A-18 in the 80- by 120-Foot Wind Tunnel of the National Full-Scale Aerodynamic Complex at NASA Ames Research Center at Moffett Field, California. A production aircraft was tested over an angle-of-attack range of 18 to 50 deg and at wind speeds of up to 100 knots. These tests had three primary test objectives. Pneumatic and mechanical forebody flow control devices were tested at full-scale and shown to produce significant yawing moments for lateral control of the aircraft at high angles of attack. Mass flow requirements for the pneumatic system were found to scale with freestream density and speed rather than freestream dynamic pressure. Detailed measurements of the pressures buffeting the vertical tail were made and spatial variations in the buffeting frequency were found. The LEX fence was found to have a significant effect on the frequency distribution on the outboard surface of the vertical fin. In addition to the above measurements, an extensive set of data was acquired for the validation of computational fluid dynamics codes and for comparison with flight test and small-scale wind tunnel test results.

Meyn, Larry A.↗
NASA NTRS1992

Flexible control techniques for a lunar base

The fundamental elements found in every terrestrial control system can be employed in all lunar applications. These elements include sensors which measure physical properties, controllers which acquire sensor data and calculate a control response, and actuators which apply the control output to the process. The unique characteristics of the lunar environment will certainly require the development of new control system technology. However, weightlessness, harsh atmospheric conditions, temperature extremes, and radiation hazards will most significantly impact the design of sensors and actuators. The controller and associated control algorithms, which are the most complex element of any control system, can be derived in their entirety from existing technology. Lunar process control applications -- ranging from small-scale research projects to full-scale processing plants -- will benefit greatly from the controller advances being developed today. In particular, new software technology aimed at commercial process monitoring and control applications will almost completely eliminate the need for custom programs and the lengthy development and testing cycle they require. The applicability of existing industrial software to lunar applications has other significant advantages in addition to cost and quality. This software is designed to run on standard hardware platforms and takes advantage of existing LAN and telecommunications technology. Further, in order to exploit the existing commercial market, the software is being designed to be implemented by users of all skill levels -- typically users who are familiar with their process, but not necessarily with software or control theory. This means that specialized technical support personnel will not need to be on-hand, and the associated costs are eliminated. Finally, the latest industrial software designed for the commercial market is extremely flexible, in order to fit the requirements of many types of processing applications with little or no customization. This means that lunar process control projects will not be delayed by unforeseen problems or last minute process modifications. The software will include all of the tools needed to adapt to virtually any changes. In contrast to other space programs which required the development of tremendous amounts of custom software, lunar-based processing facilities will benefit from the use of existing software technology which is being proven in commercial applications on Earth.

Kraus, Thomas W.↗
NASA NTRS1939

Tests of NACA 0009, 0012, and 0018 Airfoils in the Full-Scale Tunnel

An investigation was conducted in the NACA full-scale wind tunnel to determine the aerodynamic characteristics of the NACA 0009, 0012, and 0018 airfoils, with the ultimate purpose of providing data to be used as a basis for comparison with other wind-tunnel data, mainly in the study of scale and turbulence effects. Three symmetrical 6 by 36-foot rectangular airfoils were used. The Reynolds number range for minimum drag was form 1,800,000 to 7,000,000 and for maximum lift, from 1,700,000 to 4,500,000. The effect of rounded tips was determined for each of the airfoils. Tests were also made of the NACA 0012 airfoil equipped with a 0.20c full-span split flap hinged at 0.80c. Tuft surveys were included to show the progressive breakdown of flow near maximum lift. Momentum surveys were made in conjunction with force measurements at zero lift as an aid in converting force-test data to section coefficients.

Goett, Harry J↗
NASA NTRS1993

Development of a quiet supersonic wind tunnel with a cryogenic adaptive nozzle

The main objective of this work is to develop an interim Quiet (low-disturbance) supersonic wind tunnel for the NASA-Ames Fluid Mechanics Laboratory (FML). The main emphasis is to bring on-line a full-scale Mach 1.6 tunnel as rapidly as possible to impact the NASA High Speed Research Program (HSRP). The development of a cryogenic adaptive nozzle and other sophisticated features of the tunnel will now happen later, after the full scale wind tunnel is in operation. The work under this contract for the period of this report can be summarized as follows: provide aerodynamic design requirements for the NASA-Ames Fluid Mechanics Laboratory (FML) Laminar Flow Supersonic Wind Tunnel (LFSWT); research design parameters for a unique Mach 1.6 drive system for the LFSWT using an 1/8th-scale Proof-of-Concept (PoC) supersonic wind tunnel; carry out boundary layer transition studies in PoC to aid the design of critical components of the LFSWT; appraise the State of the Art in quiet supersonic wind tunnel design; and help develop a supersonic research capability within the FML particularly in the areas of high speed transition measurements and schlieren techniques. The body of this annual report summarizes the work of the Principal Investigator.

Wolf, Stephen W. D.↗
NASA NTRS1995

Computational fluid dynamic analysis of hybrid rocket combustor flowfields

Computational fluid dynamic analyses of the Navier-Stokes equations coupled with solid-phase pyrolysis, gas-phase combustion, turbulence and radiation are performed to study hybrid rocket combustor flowfields. The computational study is closely co-ordinated with a companion experimental program using a planar slab burner configuration with HTPB as fuel and gaseous oxygen. Computational predictions agree reasonably well with measurement data of fuel regression rates and surface temperatures. Additionally, most of the parametric trends predicted by the model are in general agreement with experimental trends. The computational model is applied to extend the results from the lab-scale to a full-scale axisymmetric configuration. The numerical predictions indicate that the full-scale configuration burns at a slower rate than the lab-scale combustor under identical specific flow rate conditions. The results demonstrate that detailed CFD analyses can play a useful role in the design of hybrid combustors.

Venkateswaran, S.↗
NASA NTRS1996

Overview of HATP Experimental Aerodynamics Data for the Baseline F/A-18 Configuration

Determining the baseline aerodynamics of the F/A-18 was one of the major objectives of the High-Angle-of-Attack Technology Program (HATP). This paper will review the key data bases that have contributed to our knowledge of the baseline aerodynamics and the improvements in test techniques that have resulted from the experimental program. Photographs are given highlighting the forebody and leading-edge-extension (LEX) vortices. Other data representing the impact of Mach and Reynolds numbers on the forebody and LEX vortices will also be detailed. The level of agreement between different tunnels and between tunnels and flight will be illustrated using pressures, forces, and moments measured on a 0.06-scale model tested in the Langley 7- by 10-Foot High Speed Tunnel, a 0.16-scale model in the Langley 30- by 60-Foot Tunnel, a full-scale vehicle in the Ames 80- by 120-Foot Wind Tunnel, and the flight F/A-18 High Alpha Research Vehicle (HARV). Next, creative use of wind tunnel resources that accelerated the validation of the computational fluid dynamics (CFD) codes will be described. Lastly, lessons learned, deliverables, and program conclusions are presented.

Hall, Robert M.↗
NASA NTRS1961

Preliminary Base Pressures Obtained from the X-15 Airplane at Mach Numbers from 1.1 to 3.2

Base pressure measurements have been made on the fuselage, 10 deg.-wedge vertical fin, and side fairing of the X-15 airplane. Data are presented for Mach numbers between 1.1 and 3.2 for both powered and unpowered flight. Comparisons are made with data from small-scale-model tests, semiempirical estimates, and theory. The results of this preliminary study show that operation of the interim rocket engines (propellant flow rate approximately 70 lb/sec) reduces the base drag of the X-15 by 25 to 35 percent throughout the test Mach number range. Values of base drag coefficient for the side fairing and fuselage obtained from X-15 wind-tunnel models were adequate for predicting the overall full-scale performance of the test airplane. The leading-edge sweep of the upper movable vertical fin was not an important factor affecting the fin base pressure. The power-off base pressure coefficients of the upper movable vertical fin (a 10 deg. wedge with chord-to-thickness ratio of 5.5 and semispan-to-thickness ratio of 3.2) are in general agreement with the small-scale blunt-trailing-edge-wing data of several investigators and with two-dimensional theory.

Saltzman, Edwin J.↗
NASA NTRS1961

Aerodynamic Characteristics, Temperature, and Noise Measurements of a Large-Scale External-Flow Jet-Augmented-Flap Model with Turbojet Engines Operating

An investigation has been conducted in the Langley full-scale tunnel on a large-scale model powered by turbojet engines with flattened rectangular nozzles. The wing had 35 deg. sweep of the leading edge, an aspect ratio of 6.5, a taper ratio of 0.31, and NACA 65(1)-412 and 65-408 airfoils at the root and tip. The investigation included measurements of the longitudinal aerodynamic characteristics of the model with half-span and full-span flaps and measurements of the sound pressure and skin temperature on the portions of the lower surface of the wing immersed in the jet flow. The tests were conducted over a range or angles of attack from -8 to 16 deg. for Reynolds numbers from 1.8 x 10(exp 6) to 4.4 x 10(exp 6) and a range of momentum coefficients from 0 to 2.0. In general, the aerodynamic results of this investigation made with a large-scale hot-jet model verified the results of previous investigations with small models powered by compressed-air jets. Although blowing was only done over the inboard portion of the wing, substantial amounts of induced lift were also obtained over the outboard portion of the wing. Skin temperatures were about 340 F and wing heating could be handled with available materials without cooling. Random acoustic loadings on the wing surface were high enough to indicate that fatigue failure from this source would require special consideration in the design of an external-flow jet flap system for an airplane.

Fink, Marvin P.↗
NASA NTRS1999

Acoustic Treatment Design Scaling Methods: Advanced Treatment Impedance Models for High Frequency Ranges - Volume 2

The primary purpose of this study is to develop improved models for the acoustic impedance of treatment panels at high frequencies, for application to subscale treatment designs. Effects that cause significant deviation of the impedance from simple geometric scaling are examined in detail, an improved high-frequency impedance model is developed, and the improved model is correlated with high-frequency impedance measurements. Only single-degree-of-freedom honeycomb sandwich resonator panels with either perforated sheet or "linear" wiremesh faceplates are considered. The objective is to understand those effects that cause the simple single-degree-of- freedom resonator panels to deviate at the higher-scaled frequency from the impedance that would be obtained at the corresponding full-scale frequency. This will allow the subscale panel to be designed to achieve a specified impedance spectrum over at least a limited range of frequencies. An advanced impedance prediction model has been developed that accounts for some of the known effects at high frequency that have previously been ignored as a small source of error for full-scale frequency ranges.

Kraft, R. E.↗
NASA NTRS1999

Predicting Slag Generation in Sub-Scale Test Motors Using a Neural Network

Generation of slag (aluminum oxide) is an important issue for the Reusable Solid Rocket Motor (RSRM). Thiokol performed testing to quantify the relationship between raw material variations and slag generation in solid propellants by testing sub-scale motors cast with propellant containing various combinations of aluminum fuel and ammonium perchlorate (AP) oxidizer particle sizes. The test data were analyzed using statistical methods and an artificial neural network. This paper primarily addresses the neural network results with some comparisons to the statistical results. The neural network showed that the particle sizes of both the aluminum and unground AP have a measurable effect on slag generation. The neural network analysis showed that aluminum particle size is the dominant driver in slag generation, about 40% more influential than AP. The network predictions of the amount of slag produced during firing of sub-scale motors were 16% better than the predictions of a statistically derived empirical equation. Another neural network successfully characterized the slag generated during full-scale motor tests. The success is attributable to the ability of neural networks to characterize multiple complex factors including interactions that affect slag generation.

Wiesenberg, Brent↗
NASA NTRS1999

A New Way of Testing Large Thin Membrane, Optical Modal Testing of the 1/10th Scale Model of the NASA NAGT Sunshield

The Next Generation Space Telescope design includes a deployed sunshield to thermally insulate the telescope, keeping vital detector temperatures below 60 degrees Kelvin. The sunshield consists of four struts supporting four thin film membranes. Since it would be very difficult to test the full-scale sunshield on the ground due to its size and the 1-g environment, it is important to have accurate analytical models of the sunshield to analyze its affect on the observatory. A 1/10th-scale model of the sunshield has been manufactured in order to test the analytical modeling techniques used to predict the dynamic behavior of such large, lightweight structures. A modal survey test of the scale model has been performed in a vacuum environment, using a laser vibrometer to measure the mode shapes of the membranes. The presentation describes the setup and test procedures related to these tests and presents some of the experimental results obtained and the lessons learned.

Ross, Brian↗
NASA NTRS2000

Design of the Active Elevon Rotor for Low Vibration

Helicopter fuselages vibrate more than desired, and traditional solutions have limited effectiveness and can impose an appreciable weight penalty. Alternative methods of combating high vibration, including Higher Harmonic Control (HHC) via harmonic swashplate motion and Individual Blade Control (IBC) via active pitch links, have been studied for several decades. HHC via an on-blade control surface was tested in 1977 on a full scale rotor using a secondary active swashplate and a mechanical control system. Recent smart material advances have prompted new research into the use of on-blade control concepts. Recent analytical studies have indicated that the use of on-blade control surfaces produces vibration reduction comparable to swashplate-based HHC but for less power. Furthermore, smart materials (such as piezoceramics) have been shown to provide sufficient control authority for preliminary rotor experiments. These experiments were initially performed at small scale for reduced tip speeds. More recent experiments have been conducted at or near full tip speeds, and a full-scale active rotor is under development by Boeing with Eurocopter et al. pursuing a similarly advanced full-scale implementation. The US Army Aeroflightdynamics Directorate has undertaken a new research program called the Active Elevon Rotor (AER) Focus Demo. This program includes the design, fabrication, and wind. tunnel testing of a four-bladed, 12.96 ft diameter rotor with one or two on-blade elevons per blade. The rotor, which will be Mach scaled, will use 2-5/rev elevon motion for closed-loop control and :will be tested in late 2001. The primary goal of the AER Focus Demo is the reduction of vibratory hub loads by 80% and the reduction of vibratory blade structural loads. A secondary goal is the reduction of rotor power. The third priority is the measurement and possible reduction of Blade Vortex Interaction (BVI) noise. The present study is focused on elevon effectiveness, that is, the elevon's ability to reduce all six components of the nonrotating 4/rev hub loads. Some design parameters have been kept fixed in this study, while others have been varied to determine their influence - on elevon effectiveness. The fixed parameters include all blade structural properties except for torsion stiffness; the varied parameters include torsion stiffness, elevon aerodynamic location, and the number and individual authority of elevon aerodynamic surfaces. This paper describes the preliminary design process being used for the AER, and describes and quantifies the emerging active rotor characteristics.

Fulton, Mark V.↗
NASA NTRS1960

Landing Characteristics of a Reentry Capsule with a Torus-Shaped Air Bag for Load Alleviation

An experimental investigation has been made to determine the landing characteristics of a conical-shaped reentry capsule by using torus-shaped air bags for impact-load alleviation. An impact bag was attached below the large end of the capsule to absorb initial impact loads and a second bag was attached around the canister to absorb loads resulting from impact on the canister when the capsule overturned. A 1/6-scale dynamic model of the configuration was tested for nominal flight paths of 60 deg. and 90 deg. (vertical), a range of contact attitudes from -25 deg. to 30 deg., and a vertical contact velocity of 12.25 feet per second. Accelerations were measured along the X-axis (roll) and Z-axis (yaw) by accelerometers rigidly installed at the center of gravity of the model. Actual flight path, contact attitudes, and motions were determined from high-speed motion pictures. Landings were made on concrete and on water. The peak accelerations along the X-axis for landings on concrete were in the order of 3Og for a 0 deg. contact attitude. A horizontal velocity of 7 feet per second, corresponding to a flight path of 60 deg., had very little effect upon the peak accelerations obtained for landings on concrete. For contact attitudes of -25 deg. and 30 deg. the peak accelerations along the Z-axis were about +/- l5g, respectively. The peak accelerations measured for the water landings were about one-third lower than the peak accelerations measured for the landings on concrete. Assuming a rigid body, computations were made by using Newton's second law of motion and the force-stroke characteristics of the air bag to determine accelerations for a flight path of 90 deg. (vertical) and a contact attitude of 0 deg. The computed and experimental peak accelerations and strokes at peak acceleration were in good agreement for the model. The special scaling appears to be applicable for predicting full-scale time and stroke at peak acceleration for a landing on concrete from a 90 deg. flight path at a 0 deg. It appears that the full-scale approximately the same as those obtained from the model for the range of attitudes and flight paths investigated.

McGehee, John R.↗
NASA NTRS1998

Recent Dynamic Measurements and Considerations for Aerodynamic Modeling of Fighter Airplane Configurations

As airplane designs have trended toward the expansion of flight envelopes into the high angle of attack and high angular rate regimes, concerns regarding modeling the complex unsteady aerodynamics for simulation have arisen. Most current modeling methods still rely on traditional body axis damping coefficients that are measured using techniques which were intended for relatively benign flight conditions. This paper presents recent wind tunnel results obtained during large-amplitude pitch, roll and yaw testing of several fighter airplane configurations. A review of the similitude requirements for applying sub-scale test results to full-scale conditions is presented. Data is then shown to be a strong function of Strouhal number - both the traditional damping terms, but also the associated static stability terms. Additionally, large effects of sideslip are seen in the damping parameter that should be included in simulation math models. Finally, an example of the inclusion of frequency effects on the data in a simulation is shown.

Brandon, Jay M.↗