Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “distributed wind energy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Modeling the Yaw Behavior of Tail Fins for Small Wind Turbines: November 22, 2021 - May 21, 2024

This report describes the aerodynamic modelling of the yaw behavior of tail fins for small wind turbines (SWTs). The analysis is based on unsteady slender body theory (USBT) and is formulated to be used with the proposed tail fin module to be added to OpenFAST. Linearized USBT, which has been applied in the past to SWT tail fins, is developed in three main ways. First, USBT is extended to high yaw angles and aspect ratios by modelling the associated nonlinear vortex dynamics and the chordwise load distribution respectively. Second, we consider the effect of time-varying wind speed. The extended theory is compared to recent unpublished measurements at the University of Perugia, Italy, for the yaw behavior of delta, elliptical, and rectangular tail fins without a rotor and nacelle. The fins were released from initial yaw angles of -40 degrees and -80 degrees ; the latter is of sufficient magnitude to show the importance of the nonlinear yaw dynamics. Further, the friction in the model tail fin bearings was measured and modelled. The constants in the aerodynamic models were taken from the literature but significant improvement in accuracy is achieved by using system identification techniques to optimize the values. This leads to the third main finding: extended USBT is accurate for all generic tail fin shapes that we considered and is, therefore, very suitable for inclusion in aeroelastic codes for SWTs. The final development is of a general nonlinear equation for yaw response that is simpler than the extended USBT and is also suitable for inclusion in OpenFAST. The two nonlinear models are used to highlight the geometric requirements for good tail fin design.

distributed wind↗
DOE OSTI2024

Cybersecurity for Clean Energy Resources [Slides]

This presentation provides motivation for research in clean energy cybersecurity and highlights INL projects and capabilities to address clean energy cybersecurity needs. The projects are broken down by device level, plant level, utility level, regulation level, and implementation. This introduction to INL capabilities creates opportunity for further conversations around how cohort members can improve their own organizational security postures.

14 SOLAR ENERGY↗
DOE OSTI2024

Application Guide for the Cyber-Resilient Design Framework for Hybrid Systems

As the energy landscape evolves, hybrid power plants—integrating multiple renewable energy sources (e.g., solar, wind, and battery storage) with the bulk power electric system—play a crucial role in meeting growing energy demands. However, with a hybrid power plant’s increased number of components, complex network connectivity and digitization of controls, these systems face growing cybersecurity risks. To help mitigate these risks, Idaho National Laboratory (INL) presents this application guide specifically designed for operators and systems engineers to evaluate the cybersecurity resilience of their hybrid power plant’s design.

14 SOLAR ENERGY↗
DOE OSTI2024

Hourly dynamic line ratings for existing transmission across the contiguous United States (preliminary results) [Slides]

The thermal rating of a transmission line depends on the rate at which heat generated by current flow through the line can be dissipated into the environment by convective and radiative cooling, keeping the conductor below a maximum operating temperature. Static or seasonal line ratings assume nearly-worst-case weather conditions (high ambient air temperature, high solar irradiance, and low wind speed), resulting in a low risk of "overrating" a line (i.e., allowing more current to flow than the line is designed for) but a high fraction of time when the line is "underrated" (i.e., able to flow more current while staying below the maximum temperature). Dynamic transmission line ratings (DLR) use real-time measurements of weather conditions, line sag, or line temperature to determine the thermal rating of transmission lines at hourly or higher time resolution, allowing for increased ratings during some (cold, windy, and/or dark) periods and correcting for overrating during other (hot, calm, and/or sunny) periods. Many studies have explored the benefits of DLR, but typically for small collections of transmission lines under a limited sample of weather conditions, leaving open the question of how widely applicable the benefits of DLR might be over diverse geographies and weather conditions. Here, we combine geospatial data on tens of thousands of transmission line routes across the contiguous United States with high-resolution hourly historical weather data for 2007-2013 to estimate the impact of DLR and other weather-adjusted rating systems. We compare static and dynamic line ratings to intermediate ratings adjusted by ambient temperature, day/night irradiance, clear-sky irradiance, and/or measured irradiance, illustrating the benefits of incorporating progressively more detailed weather data into the calculated line ratings. Moving from nighttime-adjusted ratings to clear-sky-adjusted ratings provides more benefit than moving from clear-sky-adjusted ratings to measured-irradiance-adjusted ratings. Depending on the assumed static windspeed for irradiance-adjusted-ratings, DLR either corrects for overrated hours or provides substantially increased ratings in the majority of hours on the majority of lines.

14 SOLAR ENERGY↗
DOE OSTI2025

Community-Centric Microgrid Feasibility Analysis Framework to Accelerate Resilience of Island Communities

Marine energy offers a reliable energy solution for island and coastal communities, which often lack traditional local generation, to support their transition to energy independence and reduce reliance on externally imported fuels. Successful deployment of new technologies in these isolated locations requires community acceptance and approval from the outset, as these communities typically lack the financial and technical resources to operate and maintain new systems. This report presents a community-centric microgrid planning framework for remote coastal and island communities. Community engagement is integrated as the first step in the planning process, incorporating community profiles and visions into energy development scenarios. A case study was conducted in St. George, Pribilof Islands, Alaska, which relies entirely on diesel yet has significant wind and wave energy potential. Community engagement revealed a unique history and current economic status, with an interest in adopting advanced energy technologies despite past failures. Various microgrid configurations were optimized, considering different technologies to meet current and future energy needs while balancing cost and energy resilience. Wave energy converters (WECs) were a key component, integrated with other energy sources using the Xendee optimization tool. The Marine Energy Microgrid Toolkit, developed as part of this work, uses commercial power system analysis tools to optimize and analyze microgrid scenarios. The developed framework and toolkit can be applied to island and coastal communities to enhance resilience and support microgrid deployments. Future enhancements will include incorporating new marine resources, developing dynamic models, and automating the integration of Xendee and PowerFactory simulations.

02 PETROLEUM↗
DOE OSTI2023

West Coast Offshore Wind Transmission Literature Review and Gaps Analysis

This review of the state of west coast OSW transmission research organizes the body of literature to date and describes the most impactful grid integration analysis and convening opportunities. It is intended as a scan of the landscape to ground impactful investments, which will guide state and federal entities and private developers to maximize net value of west coast OSW to the Nation.

17 WIND ENERGY↗
NASA NTRS1972

HEOS-A2: Press kit

The characteristics of the HEOS-A2 satellite and its assigned mission are discussed. The spacecraft carries seven experiments to investigate the strength and direction of the magnetic fields encountered, the energy distribution of protons and electrons, the nature of the solar winds, detection of micrometeorites, and low frequency solar observations. The highly elliptical polar orbit required for this mission will have an apogee of 38 earth radii. The lifetime of the satellite is expected to be one year minimum.

Allaway, H. G.↗
NASA NTRS1991

The metal abundance and specific energy of intracluster gas

The hot gas in the cores of rich galaxy clusters is metal-rich with nearly solar abundances of metals. It is not clear whether the metals were shed from galaxies via protogalactic winds or via ram-pressure stripping. It has been suggested that if metals were injected via centrally concentrated stripping, the overall abundances could be much less than those observed in cluster cores, diminishing the degree of stellar processing required. The observed energetics of intracluster gas can be used to deduce the metal injection mechanism, which in turn may allow the global metal abundance uncertainty to be resolved in the absence of spatially resolved X-ray spectra. Existing X-ray spectral and surface brightness data for galaxy clusters indicate that the gas in cool clusters has substantially greater specific energy than could have been gained through cluster collapse. Supernovae-driven protogalactic winds can provide this extra energy, while ram-pressure stripping cannot. Such protogalactic winds will distribute metals fairly homogeneously. Much processing of gas through stars is then required, with protogalaxies losing perhaps one-half of their initial luminous mass in metal-rich winds. Furthermore, the oxygen-to-iron ratio observed in two clusters indicates that the bulk of the iron in cluster gas was produced by Type II supernovae, not Type I supernovae, as is usually supposed.

White, Raymond E., III↗
NASA NTRS1992

Coronal holes and solar wind streams during the sunspot cycle

Complementary synoptic observations of the Sun and interplanetary space have been obtained nearly continuously for more than two sunspot cycles and have led to new ideas about the origin of the solar wind. These observations show an inverse correlation between wind speed at Earth and magnetic flux tube expansion in the corona, with fast wind originating from slowly diverging tubes and vice versa. Although this result is consistent with the Skylab-era concept that fast wind originates from the center of a large isolated coronal hole, it implies that the wind may be even faster at the facing edges of like-polarity holes where the flux-tubes converge as they begin their outward extension. Thus, very fast wind ought to originate from the high-latitude edges of the circumpolar holes soon after sunspot maximum and from the mid-latitude necks of the polar-hole lobes during the declining phase of the cycle. The observed inverse correlation may be understood physically in terms of a model in which Alfven waves boost the wind to high speed provided that the wave energy flux is distributed approximately uniformly at the coronal base.

Sheeley, N. R., Jr.↗
NASA NTRS2010

Air-Sea Spray Airborne Radar Profiler Characterizes Energy Fluxes in Hurricanes

A report discusses ASAP (Air-sea Spray Airborne Profiler), a dual-wavelength radar profiler that provides measurement information about the droplet size distribution (DSD) of sea-spray, which can be used to estimate heat and moisture fluxes for hurricane research. Researchers have recently determined that sea spray can have a large effect on the magnitude and distribution of the air-sea energy flux at hurricane -force wind speeds. To obtain information about the DSD, two parameters of the DSD are required; for example, overall DSD amplitude and DSD mean diameter. This requires two measurements. Two frequencies are used, with a large enough separation that the differential frequency provides size information. One frequency is 94 GHz; the other is 220 GHz. These correspond to the Rayleigh and Mie regions. Above a surface wind speed of 10 m/ s, production of sea spray grows exponentially. Both the number of large droplets and the altitude they reach are a function of the surface wind speed.

Durden, Stephen L.↗
DOE OSTI2021

Forecasting Dynamic Line Rating with Spatial Variation Considerations

Dynamic line rating (DLR) is a technology that allows the ampacity of an electrical conductor to be calculated using real-time or forecasted weather conditions. Historically, the ampacity of a conductor has been determined using a static line rating method which assumes conservative weather assumptions. Therefore, not only can DLR give a more accurate measurement of the true ampacity of a conductor, but it can also increase its ampacity during weather conditions with greater thermal mitigations. The two primary cooling factors in the ampacity calculations are wind speed and direction. In complex terrain, wind speed and direction can have large variations over short distances. Therefore, accurately identifying the limiting span of a transmission line requires high spatial resolution of the wind along its path. One solution is to install dense weather stations along their path, though this can become costly over long distances. Therefore, researchers have investigated the use of Computation Fluid Dynamic (CFD) simulations to accurately compute the wind field along the path of a transmission line and use these results to identify the limiting section of the conductor. This work presents a case study that evaluates the coupling of CFD simulations and forecasted weather simulations using the High-Resolution Rapid Refresh (HRRR) model points over a 2-year span within a region in south eastern Idaho. The primary goal of the work is the evaluation of the number of HRRR model points used, i.e., weather stations, along the path of the line and the accuracy of the resulting DLR ampacity. This was done using 4, 10, 17, 26, and 35 HRRR model points along two transmission line paths. The results indicate that as the number of model points are increased, the DLR ampacity of the lines decrease, yet converge as more points are added and demonstrate little change with additional HRRR points. It is expected that these results can help transmission line operators identify the number of weather stations that must be installed when coupled with CFD simulations and DLR ampacity to ensure accurate ratings and safe operations.

17 WIND ENERGY↗
DOE OSTI2021

Forecasting Dynamic Line Rating with Spatial Variation Considerations

Dynamic line rating (DLR) is a technology that allows the ampacity of an electrical conductor to be calculated using real-time or forecasted weather conditions. Historically, the ampacity of a conductor has been determined using a static line rating method which assumes conservative weather assumptions. Therefore, not only can DLR give a more accurate measurement of the true ampacity of a conductor, but it can also increase its ampacity during weather conditions with greater thermal mitigations. The two primary cooling factors in the ampacity calculations are wind speed and direction. In complex terrain, wind speed and direction can have large variations over short distances. Therefore, accurately identifying the limiting span of a transmission line requires high spatial resolution of the wind along its path. One solution is to install dense weather stations along their path, though this can become costly over long distances. Therefore, researchers have investigated the use of Computation Fluid Dynamic (CFD) simulations to accurately compute the wind field along the path of a transmission line and use these results to identify the limiting section of the conductor. This work presents a case study that evaluates the coupling of CFD simulations and forecasted weather simulations using the High-Resolution Rapid Refresh (HRRR) model points over a 2-year span within a region in south eastern Idaho. The primary goal of the work is the evaluation of the number of HRRR model points used, i.e., weather stations, along the path of the line and the accuracy of the resulting ampacity. This was done using 4, 10, 17, 26, and 35 HRRR model points along two transmission line paths. The results indicate that as the number of model points are increased, the DLR ampacity of the lines decrease, yet converge as more points are added and demonstrate little change with additional HRRR points. It is expected that these results can help transmission line operators identify the number of weather stations that must be installed when coupled with CFD simulations and DLR ampacity to ensure accurate ratings and safe operations.

17 WIND ENERGY↗
DOE OSTI2024

Cybersecurity Considerations for Emerging Energy Technologies

AI, cloud computing, post-quantum cryptography, zero-trust architectures, microgrids, and virtual power plants. What do these things have in common? They are all emerging technologies in the clean energy space that will be a critical part of grid modernization efforts. As we work towards clean energy and decarbonization targets, these technologies, developed to solve real-world problems, will help us reach goals and achieve new efficiencies as the paradigm of grid operation shifts. However, there are growing concerns about the cybersecurity risks associated with these trending topics as they are used in critical infrastructure applications. This talk will cover gaps, challenges, and opportunities for the secure implementation of grid modernization solutions and novel energy applications of state-of-the-art networking and communications. Proactive risk mitigation strategies, including the application of cyber-informed engineering, will be discussed. Practical applications of these techniques will help provide countermeasures to the impact of cyberattacks on critical infrastructure technologies in a new, digitized grid landscape.

14 SOLAR ENERGY↗
DOE OSTI2024

Developing a Supply Chain Security Program

Amid growing concerns over foreign manufacturing for components and devices deployed in critical energy infrastructure, this research from the national labs will highlight best practices for developing and maintaining a supply chain security program. Tools for asset inventory, tips for developing and maintaining software- and hardware-bills-of-materials (SBOMs and HBOMs), recommended contractual language for vendor agreements, and identification of responsibilities will be shared. We discuss the one-time requirements to enable a successful supply chain security program and the best ways to operationalize this program for maximum impact, including development of robust practices for vulnerability tracking, patch management, and workarounds, with understanding of the reliability and uptime requirements for utilities. The recommendations shared are based on a cyber-informed engineering approach to identification of high-consequence impacts and the engineering controls related to supply chain management that can best mitigate these impacts. This approach allows for prioritization of resources. Additionally, we highlight relative up-front and ongoing costs associated with recommended controls. Viewers will leave with an understanding what a supply chain security program is, and what steps, prioritized for resource-constrained organizations, can build a robust program.

14 SOLAR ENERGY↗