Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “direct casting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Improving creep resistance of Al-0.27Zr-0.08Sn (wt%) via cold swaging while maintaining high electrical conductivity

This study investigates the effect of mechanical cold work (0, 50, and 90% cross-sectional area reduction via swaging) on the creep properties of cast aluminum alloys with high electrical conductivity including high-purity Al (HP-Al), Al-0.15Zr (Al-Zr), and Al-0.27Zr-0.08Sn (Al-Zr-Sn, wt%). The Al-Zr alloy is strengthened by Zr in solid solution while the Al-Zr-Sn alloy is additionally strengthened by Al3Zr nanoprecipitates (8 nm diameter). After 90% cold swaging, the alloys exhibit grains elongated along the swaging direction with their widths ranging between 8 and 152 μm perpendicular to the swaging direction. Creep testing at 200 °C shows that the minimum creep rate of all 90% swaged alloys shows high sensitivity to stress, which can be modeled via a threshold stress σth. Increasing swaging magnitude from 0 to 50 to 90% in Al-Zr-Sn improves the creep resistance without reducing electrical conductivity. The formation of subgrains, increased dislocation density, and columnar grain structure in swaged alloys all enhance creep resistance. HP-Al swaged to 90% exhibits much lower creep resistance (σth = 18 MPa) due to subgrain coarsening and the absence of precipitates compared to Al-Zr (σth = 40 MPa) and Al-Zr-Sn (σth = 40 MPa), which maintain stable subgrain structures and benefit from solid solution strengthening and Al3Zr nanoprecipitates, respectively. Although Al3Zr precipitates are known to stabilize the deformed microstructure by pinning grain-boundaries, this work demonstrates that Zr in solid solution alone can effectively stabilize the deformed microstructure resulting in enhanced creep resistance. This effect of Zr solute on stabilizing grain boundaries for creep performance was not previously well-defined in the literature. Despite similar creep performances of Al-Zr and Al-Zr-Sn, the latter shows 70% higher room-temperature microhardness and slightly improved electrical conductivity (56%IACS (International Annealed Copper Standard) vs. 57%IACS, respectively). This work provides new insights into creep mechanisms of cold-worked Al–Zr alloys that will guide the design of heat-resistant Al conductors for high-demand applications.

Coello ramirez, Ismael [Northwestern University,]↗
NASA NTRS1999

Themes from a NASA workshop on gene regulatory processes in development and evolution

A memorable workshop, focused on causal mechanisms in metazoan evolution and sponsored by NASA, was held in early June 1998, at MBL. The workshop was organized by Mike Levine and Eric H. Davidson, and it included the PI and associates from 12 different laboratories, a total of about 30 people. Each laboratory had about two and one half hours in which to represent its recent research and cast up its current ideas for an often intense discussion. In the following we have tried to enunciate some of the major themes that emerged, and to reflect on their implications. The opinions voiced are our own. We would like to tender apologies over those contributions we have not been able to include, but this is not, strictly speaking, a meeting review. Rather we have focused on those topics that bear more directly on evolutionary mechanisms, and have therefore slighted some presentations (including some of our own), that were oriented mainly toward developmental processes. J. Exp. Zool. (Mol. Dev. Evol. ) 285:104-115, 1999. Copyright 1999 Wiley-Liss, Inc.

NASA Discipline General Space Life Sciences↗
DOE OSTI2022

Impacts of the Additive Manufacturing Process on the Roughness of Engine Scale Vanes and Cooling Channels

Abstract By leveraging the additive manufacturing (AM) platform, development time and costs for turbine component testing can be reduced relative to traditional investment casting. Surface roughness is a key characteristic of the additive manufacturing process that can impact flow, heat transfer, and mechanical integrity of printed components. There are multiple design and build considerations that result in variability in surface roughness, especially when additively fabricating complicated three-dimensional vanes and internal cooling passages. This study characterizes the surface roughness of internal cooling passages, vanes, and flat external surface samples made using additive manufacturing, specifically the direct metal laser sintering process. The samples were manufactured with various wall thicknesses, layer thicknesses, build locations, build directions, and on different AM machines. A combination of computed tomography scanning and optical profilometry was used to evaluate surface roughness levels. The data indicate that the dominant factors in roughness for a given layer thickness are a function of wall thickness, build location, and build direction.

Engineering↗
NASA NTRS1979

Composites for Advanced Space Transportation Systems - (CASTS)

The CASTS Project initiated to develop graphite fiber/polyimide matrix (GR/PI) composite structures with 589K operational capability for aerospace vehicles is described. Near term tasks include screening composites and adhesives for 589K service, developing fabrication procedures and specifications, developing design allowables test methods and data, design and test of structural elements, and construction of a full scale aft body flap for the space shuttle orbiter vehicle for ground testing. Far term tasks include research efforts directed at new materials, manufacturing procedures and design/analysis methodology. Specific results discussed include: (1) identification of four GR/PI composites and three PI adhesives with 589K service potential for periods ranging from 125 to 500 hours; (2) development of an adhesive formulation suitable for bonding reusable surface insulation (RSI) titles to 589K (GR/PI) substructure; (3) the capability to fabricate and nondestructively inspect laminates, hat section shaped stiffeners, honeycomb sandwich panels, and chopped fiber moldings; and (4) test methods for measuring design allowables at 117K.

Davis, J. G., Jr.↗
DOE OSTI2020

Edge States Drive Exciton Dissociation in Ruddlesden–Popper Lead Halide Perovskite Thin Films

Efficient photovoltaic cells based on thin films of solution-processed 2D Ruddlesden–Popper hybrid perovskites (RPPs) represent an exciting breakthrough due to their enhanced tunability and chemical stability relative to those fabricated from 3D phases. However, reports of efficient charge separation and current collection are in apparent contradiction with the well-known enhancement of the exciton binding energy in multilayered halide perovskites, which should lower the device’s internal quantum efficiency and voltage. This controversy has led to various proposals for the electronic and physical structure of RPP thin films, including phase inhomogeneity as the driving force for exciton dissociation and transport. We address this apparent paradox in high-quality hot-cast RPP films by correlating ultrafast transient absorption spectroscopy with X-ray scattering measurements. We show that a hot-casting fabrication method produces highly phase pure n = 3 (BA) 2 (MA) n-1 Pb n I 3n+1 RPP structures. The high-phase purity and large grain sizes allow us to observe vertical transport of excitons via a diffusive process and allow us to determine that charge separation is primarily driven by dissociation at surface localized subgap electronic states. Furthermore, we analyze the differential absorption kinetics in films of varying thickness to directly determine that the excitonic diffusion constant is ~0.18 cm 2 s –1 . We propose that a surface localized structural distortion, observed using surface selective grazing incidence X-ray scattering measurements, is responsible for the creation of the surface localized defect states. We find that the density and spatial distribution of these defect states is a function of preparation conditions.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

A new platform for development of photosystem I based thin films with superior photocurrent: TCNQ charge transfer salts derived from ZIF-8

The transmembrane photosynthetic protein complex Photosystem I (PSI) is highly sought after for incorporation into biohybrid photovoltaic devices due to its remarkable photoactive electrochemical properties, chiefly driving charge separation with ~1 V potential and ~100% quantum efficiency. In pursuit of these integrated technologies, three factors must be simultaneously tuned, namely, direct redox transfer steps, three-dimensional coordination and stabilization of PSI aggregates, and interfacial connectivity with conductive pathways. Building on our recent successful encapsulation of PSI in the metal–organic framework ZIF-8, herein we use the zinc and imidazole cations from this precursor to form charge transfer complexes with an extremely strong organic electron acceptor, TCNQ. Specifically, the PSI-Zn-H 2 mim-TCNQ charge transfer salt complex was drop cast on ITO to form dense films. Subsequent voltammetric cycling induced cation exchange and electrochemical annealing of the film was used to enhance electron conductivity giving rise to a photocurrent in the order of 15 μA cm -2 . This study paves the way for a myriad of future opportunities for successful integration of this unique class of charge transfer salt complexes with biological catalysts and light harvesters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Predicting Thermal Excursions During in situ Oxidative Regeneration of Packed Bed Catalytic Fast Pyrolysis Catalyst

Ex situ catalytic fast pyrolysis (CFP) uses a secondary reactor to upgrade biomass pyrolysis vapors to stabilized CFP oils with reduced oxygen content. In one configuration, the secondary reactor is operated as a packed-bed swing reactor system which allows coke-deactivated beds to be decarbonized in situ while other beds remain online for vapor upgrading. In situ decarbonization must be done carefully to avoid irreversible deactivation and/or physical degradation of catalyst pellets. Given that packed bed reactors are well known to have poor heat transfer characteristics, this is a critical issue impacting scaleability and commercial viability of the technology. To predict thermal excursions during regeneration, finite element computational models have been built to assist in scaling up oxidative decarbonization of a Pt/TiO2 CFP catalyst (0.5 mm spheres) from a bench scale packed bed with 100 g of catalyst to a pilot scale packed bed with 2 kg of catalyst and internal cooling tubes. Based on transient measurements of outlet temperature and effluent CO2 concentration, and using an assumed coke profile and activation energy, this paper demonstrates that specific combinations of effective thermal conductivity and wall heat transfer coefficient can fit bench scale oxidative regeneration data equally well. For the upscaled 2 kg bed, four bench-scale “best fit” parameter pairs give different predictions for location and magnitude of thermal excursions, with the maximum computed bed temperature gradients ranging from 30 °C cm-1 to as high as 3000 °C cm-1. The larger the fraction of heat removal by conduction through the cooling tubes, the greater the differences between the parameter pairs. The modelling results presented in this paper cast doubt on the industrial viability of the proposed combination of catalyst, bed and regeneration process, and point to the need for alternate reactor designs. However, there is considerable uncertainly in some of the key model parameters. The reliability of model predictions can be increased by adding more temperature measurements at key bed locations, testing additional variations in process conditions, performing careful bed dissections to determine the true coke profile, and perhaps most importantly, directly measuring the effective thermal conductivity of the catalyst pellets.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Highly Efficient Vacuum Smelting of Aluminum

The goal of this SBIR project was to develop and demonstrate an innovative aluminum smelting technology that will significantly increase the range of aluminum alloys that can be manufactured from recycling of scrap aluminum. This will result in reduction of need for primary aluminum with corresponding 95% energy and CO 2 emission benefits. The proposed melting of pre-sorted aluminum alloys using UHV’s patented high throughput sorter funded by ARPA-E METALS program in an energy efficient vacuum furnace avoids the typical 5% metal loss due to oxidation of molten metal. In addition, pre-sorting scrap into different categories (cast, wrought, extrusion and aerospace) allows lower cost production of high value aluminum alloys without the need for adding alloying elements to primary aluminum. During this SBIR project, pure aluminum and several different commercial alloys were procured and melted in a laboratory furnace in vacuum, CH4 and air environments. The slag and oxidation formation were measured using weight and cross-sectional scanning electron microscope. The results otained were mixed and did not show direct correlation between furnace pressure and oxidation. We believe that the results were tainted due to small furnace size and non-uniformity of oxidation layer. A more thorough investigation is required to prove the advantages of vacuum smelting which could not be performed due to the COVID-19 lockdowns during this project. The theoretical fact remains that in the absence of oxygen in the furnace, there should be no oxide after melting, however the team could not prove it experimentally, and thus decided to dis-continue the project.

36 MATERIALS SCIENCE↗
NASA NTRS1991

Compression, bend, and tension studies on forged Al67Ti25Cr8 and Al66Ti25Mn(g) L1(2) compounds

Cast, homogenized, and isothermally forged aluminum-rich L1(2) compounds Al67Ti25Cr8 and Al66Ti25Mn(g) were tested in compression as a function of temperature and as a function of strain rate at elevated temperatures (1000 K and 1100 K). Three-point bend specimens were tested as a function of temperature in the range 300 K to 873 K. Strain gages glued on the tensile side of the ambient and 473 K specimens enabled direct strain measurements. A number of 'buttonhead' tensile specimens were electro-discharge machined, fine polished, and tested between ambient and 1073 K for yield strength and ductility as a function of temperature. Scanning electron microscope (SEM) examination of fracture surfaces from both the bend and tensile specimens revealed a gradual transition from transgranular cleavage to intergranular failure with increasing temperature.

Kumar, K. S.↗
NASA NTRS1981

The growth of metastable peritectic compounds

The influence of gravitationally driven thermosolutal convection on the directional solidification of peritectic alloys is considered as well as the relationships between the solidification processing conditions, and the microstructure, chemistry, and magnetic properties of such alloys. Analysis of directionally solidified Pb-Bi peritectic samples indicates that appreciable macrosegregation occurs due to thermosolutal convection and/or Soret diffusion. A peritectic solidification model which accounts for partial mixing in the liquid ahead of the planar solidification interface and describes macrosegregation has been developed. Two-phase dendritic and banded microstructures were grown in the Pb-Bi peritectic system, refined two-phase microstructures have were observed, and candidate formation mechanisms proposed. Material handling, containment, casting, microstructural and magnetic characterization techniques were developed for the Sm-Co system. Alloys produced with these procedures are homogeneous.

Larson, D. J., Jr.↗
NASA NTRS1996

Advancement of Solidification Processing Technology Through Real Time X-Ray Transmission Microscopy: Sample Preparation

Two types of samples were prepared for the real time X-ray transmission microscopy (XTM) characterization. In the first series directional solidification experiments were carried out to evaluate the critical velocity of engulfment of zirconia particles in the Al and Al-Ni eutectic matrix under ground (l-g) conditions. The particle distribution in the samples was recorded on video before and after the samples were directionally solidified. In the second series samples of the above two type of composites were prepared for directional solidification runs to be carried out on the Advanced Gradient Heating Facility (AGHF) aboard the space shuttle during the LMS mission in June 1996. X-ray microscopy proved to be an invaluable tool for characterizing the particle distribution in the metal matrix samples. This kind of analysis helped in determining accurately the critical velocity of engulfment of ceramic particles by the melt interface in the opaque metal matrix composites. The quality of the cast samples with respect to porosity and instrumented thermocouple sheath breakage or shift could be easily viewed and thus helped in selecting samples for the space shuttle experiments. Summarizing the merits of this technique it can be stated that this technique enabled the use of cast metal matrix composite samples since the particle location was known prior to the experiment.

Stefanescu, D. M.↗
NASA NTRS1989

Analysis and test of insulated components for rotary engine

The direct-injection stratified-charge (DISC) rotary engine, while attractive for aviation applications due to its light weight, multifuel capability, and potentially low fuel consumption, has until now required a bulky and heavy liquid-cooling system. NASA-Lewis has undertaken the development of a cooling system-obviating, thermodynamically superior adiabatic rotary engine employing state-of-the-art thermal barrier coatings to thermally insulate engine components. The thermal barrier coating material for the cast aluminum, stainless steel, and ductile cast iron components was plasma-sprayed zirconia. DISC engine tests indicate effective thermal barrier-based heat loss reduction, but call for superior coefficient-of-thermal-expansion matching of materials and better tribological properties in the coatings used.

Badgley, Patrick R.↗
NASA NTRS2004

A Study of Penalty Function Methods for Constraint Handling with Genetic Algorithm

COMETBOARDS (Comparative Evaluation Testbed of Optimization and Analysis Routines for Design of Structures) is a design optimization test bed that can evaluate the performance of several different optimization algorithms. A few of these optimization algorithms are the sequence of unconstrained minimization techniques (SUMT), sequential linear programming (SLP) and the sequential quadratic programming techniques (SQP). A genetic algorithm (GA) is a search technique that is based on the principles of natural selection or "survival of the fittest". Instead of using gradient information, the GA uses the objective function directly in the search. The GA searches the solution space by maintaining a population of potential solutions. Then, using evolving operations such as recombination, mutation and selection, the GA creates successive generations of solutions that will evolve and take on the positive characteristics of their parents and thus gradually approach optimal or near-optimal solutions. By using the objective function directly in the search, genetic algorithms can be effectively applied in non-convex, highly nonlinear, complex problems. The genetic algorithm is not guaranteed to find the global optimum, but it is less likely to get trapped at a local optimum than traditional gradient-based search methods when the objective function is not smooth and generally well behaved. The purpose of this research is to assist in the integration of genetic algorithm (GA) into COMETBOARDS. COMETBOARDS cast the design of structures as a constrained nonlinear optimization problem. One method used to solve constrained optimization problem with a GA to convert the constrained optimization problem into an unconstrained optimization problem by developing a penalty function that penalizes infeasible solutions. There have been several suggested penalty function in the literature each with there own strengths and weaknesses. A statistical analysis of some suggested penalty functions is performed in this study. Also, a response surface approach to robust design is used to develop a new penalty function approach. This new penalty function approach is then compared with the other existing penalty functions.

Ortiz, Francisco↗
NASA NTRS2006

Metallurgical Mechanisms Controlling Mechanical Properties of Aluminum Alloy 2219 Produced By Electron Beam Freeform Fabrication

The electron beam freeform fabrication (EBF3) layer-additive manufacturing process has been developed to directly fabricate complex geometry components. EBF3 introduces metal wire into a molten pool created on the surface of a substrate by a focused electron beam. Part geometry is achieved by translating the substrate with respect to the beam to build the part one layer at a time. Tensile properties have been demonstrated for electron beam deposited aluminum and titanium alloys that are comparable to wrought products, although the microstructures of the deposits exhibit features more typical of cast material. Understanding the metallurgical mechanisms controlling mechanical properties is essential to maximizing application of the EBF3 process. In the current study, mechanical properties and resulting microstructures were examined for aluminum alloy 2219 fabricated over a range of EBF3 process variables. Material performance was evaluated based on tensile properties and results were compared with properties of Al 2219 wrought products. Unique microstructures were observed within the deposited layers and at interlayer boundaries, which varied within the deposit height due to microstructural evolution associated with the complex thermal history experienced during subsequent layer deposition. Microstructures exhibited irregularly shaped grains, typically with interior dendritic structures, which were described based on overall grain size, morphology, distribution, and dendrite spacing, and were correlated with deposition parameters. Fracture features were compared with microstructural elements to define fracture paths and aid in definition of basic processing-microstructure-property correlations.

Domack, Marcia S.↗
DOE OSTI2021

Activation of dislocations in Mg with solute Y

Mg-Y cast alloy shows excellent ductility (elongation to failure > 15%) compared with pure Mg and commercial Mg cast alloys. By monitoring the microstructure evolution during an in situ tensile test of a Mg-2.5 wt%Y alloy, we identify the activation of prismatic slip, which is rare in Mg. Synchrotron X-ray micro-beam Laue diffraction (μ-Laue) and transmission electron microscopy revealed the morphology of prismatic slip bands and individual dislocations. Density functional theory and molecular dynamics calculations indicate that solute Y can significantly reduce the stacking fault energy (SFE) along direction on prismatic plane in Mg lattice and thus facilitate the nucleation of dislocations during deformation. The presence of free dislocations in the Mg lattice can also lead to nucleation of {10–12} twins even under unfavorable geometric conditions.

36 MATERIALS SCIENCE↗
NASA NTRS1994

Development of Advanced Alloys using Fullerenes

Development of advanced alloys using fullerenes is currently underway to produce materials for use in the extravehicular mobility unit (EMU). These materials will be directed toward commercial usages as they are continually developed. Fullerenes (of which the most common is C(sub 60)) are lightweight, nanometer size, hollow molecules of carbon which can be dispersed in conventional alloy systems to enhance strength and reduce weight. In this research, fullerene interaction with aluminum is investigated and a fullerene-reinforced aluminum alloy is being developed for possible use on the EMU. The samples were manufactured using standard commercial approaches including powder metallurgy and casting. Alloys have been processed having 1.3, 4.0 and 8.0 volume fractions of fullerenes. It has been observed that fullerene dispersion is related to the processing approach and that they are stable for the processing conditions used in this research. Emphasis will be given to differential thermal analysis and wavelength dispersive analysis of the processed alloys. These two techniques are particularly useful in determining the condition of the fullerenes during and after processing. Some discussion will be given as to electrical properties of fullerene-reinforced materials. Although the aluminum and other advanced alloys with fullerenes are being developed for NASA and the EMU, the properties of these materials will be of interest for commercial applications where specific Dual-Use will be given.

Sims, J.↗
NASA NTRS1996

ROSAT observations of the Orion-Eridanus superbubble

The Orion-Eridanus bubble is a superbubble created by the Orion OB1 stellar association. The X-ray emission from the interior of this bubble forms a prominent feature of the soft X-ray diffuse background extending across approximately 20 x 35 deg. The Rosat all sky survey maps of this object show various soft X-ray shadows cast by neutral foreground clouds against the bright emission of the superbubble interior. The velocities of some of these absorbing clouds were identified and distance limits were established, providing a 3D model of the bubble. The data are consistent with a model for the bubble in which the structure is formed by stellar winds and a recent supernova. Absorption features associated with the shell of the local bubble were identified which enable constraints to be placed on the distance and direction and to obtain measurement of the thermal pressure of the hot gas in this direction.

Burrows, David N.↗
NASA NTRS2000

1300 K Compressive Properties of Directionally Solidified Ni-33Al-33Cr-1Mo

The Ni-33Al-33Cr-1Mo eutectic has been directionally solidified by a modified Bridgeman technique at growth rates ranging from 7.6 to 508 mm/h to produce grain/cellular microstructures, containing alternating plates of NiAl and Cr alloyed with Mo. The grains had sharp boundaries for slower growth rates (< 12.7 mm/h), while faster growth rates (> 25.4 mm/h) lead to cells bounded by intercellular regions. Compressive testing at 1300 K indicated that alloys DS'ed at rates between 25.4 to 254 mm/h possessed the best strengths which exceed that for the as-cast alloy.

Whittenberger, J. Daniel↗