Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “difference graphs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Strength Differential Measured in Inconel 718: Effects of Hydrostatic Pressure Studied

Aeropropulsion components, such as disks, blades, and shafts, are commonly subjected to multiaxial stress states at elevated temperatures. Experimental results from loadings as complex as those experienced in service are needed to help guide the development of accurate viscoplastic, multiaxial deformation models that can be used to improve the design of these components. During a recent study on multiaxial deformation (ref. 1) on a common aerospace material, Inconel 718, it was shown that the material in the aged state exhibits a strength differential effect (SDE), whereby the uniaxial compressive yield and subsequent flow behavior are significantly higher than those in uniaxial tension. Thus, this material cannot be described by a standard von Mises yield formulation. There have been other formulations postulated (ref. 2) that involve other combinations of the stress invariants, including the effect of hydrostatic stress. The question remained as to which invariants are necessary in the flow model. To capture the physical mechanisms occurring during deformation and reflect them in the plasticity formulation, researchers examined the flow of Inconel 718 under various amounts of hydrostatic stress to determine whether or not hydrostatic stress is needed in the formulation. Under NASA Grant NCC3-464, monitored by the NASA Glenn Research Center, a series of tensile tests were conducted at Case Western Reserve University on aged (precipitation hardened) Inconel 718 at 650 C and with superimposed hydrostatic pressure. Dogbone shaped tensile specimens (3-mm-diameter gauge by 16-mm gauge length) and cylindrical compression specimens (3-mm-diameter gauge by 6-mm gauge length) were strain gauged and loaded in a high-pressure testing apparatus. Hydrostatic pressures were obtained with argon and ranged from 210 to 630 MPa. The aged Inconel 718 showed a pronounced difference in the tension and compression yield strength (i.e., an SDE), as previously observed. Also, there were no significant effects of hydrostatic pressure on either the tensile and compressive yield strength (see the graph) or on the magnitude of the SDE. This behavior is not consistent with the pressure-dependent theory of the SDE, which postulates that the SDE is associated with pressure-dependent and/or internal friction dependent deformation associated with non-Schmid effects at the crystal level (refs. 3 and 4). Flow in Inconel 718 appears to be independent of hydrostatic pressure, suggesting that this invariant may be removed from the phenomenological constitutive model. As part of an ongoing effort to develop advanced constitutive models, Glenn s Life Prediction Branch coordinated this work with that of research on the multiaxial deformation behavior of Inconel 718 being conducted at Pennsylvania State University under NASA Grant NCC597.

Lewandowski, John J.↗
DOE OSTI2020

Anatomical Fraction segmentation in the biomass bales

The U.S. Department of Energy Bioenergy Technologies Office (BETO) is committed to the development of sustainable, nationwide, commercial biofuel production to displace petroleum-derived fuels, increase domestic energy production, and encourage the creation of a domestic bioenergy and bioproducts industry. Operating a commercial-scale bioenergy operation requires significant technological advancements for determining biomass feedstock quality during the preprocessing stage. Usage of non-food feedstocks- e.g., corn-stover, pine residue, and forest residue - at the biorefineries reduces strain on the food supply chain. But the non-food feedstock heterogeneity- physical size, shape, and chemical composition-poses a significant challenge during milling, conveyance, feeding, and biofuel conversion processes. 3D X-Ray imaging (CT) is capable of distinguishing material features by detecting density and compositional differences. But the inherent complexity introduced during harvesting and bailing makes the reconstruction and interpretation of baled biomass materials from x-ray data time consuming, laborious, and expensive. Feedstocks are low-density materials that produce small contrast differences in the x-ray images. This paper focuses on using the shape and texture properties, using 3D image processing techniques like 3D skeletonization, directional statistics to characterize and extract volumetric content of the different tissue samples in the biomass bales.

09 BIOMASS FUELS↗
DOE OSTI2021

Resilience of electric utilities during the COVID-19 pandemic in the framework of the CIGRE definition of Power System Resilience

Resilience is a vital concept in engineering, business, and natural sciences, and is a measure of the ability of an entity to withstand High Impact Low Probability (HILP) events. During the COVID-19 pandemic, which started in late 2019/early 2020, power system utilities around the globe have responded in effective and efficient ways to enhance the resilience of their organisations, both in terms of real-time operations and prudent management of its infrastructure, in order to continue their mandate in providing reliable supply to meet customer demands. Here, this paper presents the CIGRE definition for power system resilience, established by the C4.47 Working Group in 2018, and demonstrates the application of resilience-oriented thinking within the electrical sector. The response and recovery efforts are described, with respect to the key actionable measures integral to the power system resilience definition, taken before, during and after the COVID-19 pandemic. A practical conceptual framework is also presented for thinking about resilience in terms of three key components of resilience strategies: organisational, infrastructure and operational resilience. The paper also discusses the different strategies adopted in response to COVID-19, based on the C4.47 members’ experiences during the pandemic. Finally, a case study is presented, which proves the effectiveness of a set of response measures, using graph theory and the characteristics of the staff-asset interactions.

42 ENGINEERING↗
DOE OSTI2025

Open Source Software Prevalence Ingest Tool

The OSSP Ingest Tool accepts user-input organizational information, ingests IT/OT asset lists in Excel format, and ingests the associated CycloneDX SBOM's. It then performs analytics demonstrating the ability to answer the follow research questions: o RQ1. Ability to identify all OSS services running on, and all OSS components present within, an OT device o RQ1a: Ability to differentiate multiple versions of the same OSS component within each OT device. o RQ1b: Ability to differentiate running from not-running OSS components. o RQ1c: Ability to differentiate based on the originator of the component, because a supplier may have modified it after retrieval from the upstream software source. o RQ2. Ability to correlate the identity of a single OSS component across multiple OT devices, mitigating common name variations such as differences in capitalization, '-' vs '_', and so on. o RQ3. Ability to perform subset analysis of OSS components across multiple OT devices o RQ3a: Ability to perform subset analysis across OSS libraries, generating density & distribution graphs to identify commonly-used libraries and outliers. o RQ3b: Ability to perform subset analysis of a single OSS library, generating density & distribution by CI sector, by device type, by device make/model, and/or by firmware version. o RQ3c: Ability to perform subset analysis by grouping OSS libraries according to programming language, then overlay with RQ4b. o RQ3d: Ability to perform subset analysis by OSS upstream source, providing insight into degree of modifications performed by suppliers. o RQ4. Ability to identify dependencies (transitive and direct) of each differentiated OSS library within each OT device, and enable RQ1,2,3 iteratively for dependencies. o RQ1. Ability to identify all OSS services running on, and all OSS components present within, an OT device o RQ1a: Ability to differentiate multiple versions of the same OSS component within each OT device. o RQ1b: Ability Page

Kapadia, Shayna [Lawrence Livermore National Labor↗
NASA NTRS1968

Projection transparencies from printed material

Method for preparing project transparencies, or view graphs, permits the use of almost any expendable printed material, pictures, charts, or text, in unlimited color or black and white. The method can be accomplished by either of two techniques, with a slight difference in materials.

Grunewald, L. S.↗
NASA NTRS1981

A program to evaluate a control system based on feedback of aerodynamic pressure differentials. Part 2: Data report for phase 1 wind tunnel test

Wind tunnel test data are presented. The purpose of the test was to determine the sensor location for sensitivity to flap deflection and to determine the range required of the sensor. The calculations followed to correct the raw pressure measurements, the corrected measurements, which represent the static pressures along the airfoil surface, and the static pressures tabulated and in coefficient form are described. However, the chordwise locations of the upper and lower surface taps do not coincide. An interpolation routine is performed to find the lower surface pressure coefficients at the upper surface tap locations. The difference, C sub P(lower) - C sub P(upper), is calculated and listed and the data are reorganized with respect to each tap location. A numerical regression performed to quantify the slopes of the graphs allows more accurate comparison of sensitivity and linearity.

Hrabak, R. R.↗
DOE OSTI2025

Learning to Simulate Aerosol Dynamics with Graph Neural Networks

Aerosol effects on climate, weather, and air quality depend on characteristics of individual particles, which are tremendously diverse and change in time. Particle-resolved models are the only models able to capture this diversity in particle physiochemical properties, and these models are computationally expensive. As a strategy for accelerating particle-resolved microphysics models, we introduce Graph-based Learning of Aerosol Dynamics (GLAD) and use this model to train a surrogate of the particle-resolved model PartMC-MOSAIC. GLAD implements a Graph Network-based Simulator (GNS), a machine learning framework that has been used to simulate particle-based fluid dynamics models. In GLAD, each particle is represented as a node in a graph, and the evolution of the particle population over time is simulated through learned message passing. Here, we demonstrate our GNS approach on a simple aerosol system that includes condensation of sulfuric acid onto particles composed of sulfate, black carbon, organic carbon, and water. A graph with particles as nodes is constructed, and a graph neural network (GNN) is then trained using the model output from PartMC-MOSAIC. The trained GNN can then be used for simulating and predicting aerosol dynamics over time. Results demonstrate the framework's ability to accurately learn chemical dynamics and generalize across different scenarios, achieving efficient training and prediction times. We evaluate the performance across four scenarios, highlighting the framework's robustness and adaptability in modeling aerosol microphysics and chemistry.

aerosol chemistry dynamics↗
DOE OSTI2020

Oak Ridge National Laboratory Technical Input for the Nuclear Regulatory Commission Review of the 2017 Edition of ASME Section III, Division 5, ‘High Temperature Reactors’

To assist the Nuclear Regulatory Commission in its decision making on endorsement of the American Society for Mechanical Engineers Boiler and Pressure Vessel Code Section III, Division 5 (2017 Edition) for development of advanced non-light water reactors, the following Division 5 portions were reviewed: Article HBB-2000 Material; Article HCB-2000 Material; Article HGB-2000 Material; Mandatory Appendix HBB-I-14 Tables and Figures; and, Nonmandatory Appendix HBB-U Guidelines for Restricted Material Specifications to Improve Performance in Certain Service Applications. In addition to the 2017 Edition, the same parts of the 2019 Edition have also been reviewed as indicated in various sections of the report. This review was conducted by a collaboration of national laboratory and private sector participants with significant industrial experience, including some heavy lifting and deep diving from Clarus Consulting, LLC., all intended to achieve an objective, independent, and practical perspective. The report provides recommendations, descriptions of the evaluation methods, and the source references for the data used. To build confidence required for endorsement of the Code, this review was conducted as a verification and validation of the above Code contents. The objective of verification is to ensure that the Code is free of error – direct or implied; contains the information needed for its use, including proper coverage of the Code-specified materials for the intended application, and completeness and adequacy of references to other portions of the Code. The objective of validation is to authenticate that the Code tabulations and graphs represent design inputs consistent with what are determined using rules and methods specified by the Code. The authentication process used data that were assembled and/or generated independent of Code development, while the methods of analysis followed Code-specified methods where appropriate. The designated portions for this review cover the five alloys codified for high temperature reactor applications in Division 5, i.e. 316 SS, 304 SS, 800H, 2¼Cr-1Mo, and 9Cr-1Mo-V, regarding their general requirements, permitted specifications and design stress intensity values for pressure-retaining applications, deterioration in service, fatigue acceptance test, permissible weld materials, tensile and yield strength, expected minimum stress-to-rupture values (including for Alloy 718), weld stress rupture factors, permissible materials for bolting use, and restricted specifications in certain service applications. Additionally, stress intensity values for bolting materials including 316 SS, 304 SS and alloy 718 were reviewed. Analysis and discussion are also provided on contents outside of these designated Code portions where it was deemed relevant and necessary to develop a technically sound understanding of issues relating to the designated portions. Due to unavailability of sufficient test data on welds during the review period, the weld stress rupture factors in Tables HBB-I-10.14A to E, which cover a total of ten tables for the five alloys welded with twenty-eight different weld metals (some with similar properties), have been deferred to a future review effort. The review identified mainly two types of issues. The first type includes instances where the Code is found factually incomplete or incorrect, such as obsolete materials specifications listings, missing tabulation of stresses for bolting. Changes to the Code are recommended in these cases. The second type of issue includes instances where the Code tabulations and graphs are found to be less conservative than the review analysis results. In these cases, recommendations are made for further review and consideration where the difference in conservatism exceeds 10%, which is our threshold for questioning technical adequacy, meriting a risk assessment by the Nuclear Regulatory Commission and/or reactor designers. It is noted that this effort has been executed using all available data and established methods of analysis, including methods and criteria specified and used by the Code. As such, the findings that are presented in quantitative detail, in a format for convenient comparison with the Code, and with identification of where further review is recommended, should provide a sound technical basis for decisions about quantifying the implications of the reduced design margins and technical adequacy/inadequacy to form a basis for conditioning specific Code tabulation values on endorsement. Recommendations for specific changes to the Code, however, entail design conservatism considerations beyond the scope of this review effort, and are not made in this report.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Recursive Gaussian Process over graphs for Integrating Multi-timescale Measurements in Low-Observable Distribution Systems

The transition to a smarter grid is empowered by enhanced sensor deployments and smart metering infrastructure in the distribution system. Measurements from these sensors and meters can be used for many applications, including distribution system state estimation (DSSE). However, these measurements are typically sampled at different rates and could be intermittent due to losses during the aggregation process. These multi timescale measurements should be reconciled in real-time to perform accurate grid monitoring. This paper tackles this problem by formulating a recursive multi-task Gaussian process (RGP-G) approach that sequentially aggregates sensor measurements. Specifically, we formulate a recursive multi-task GP with and without network connectivity information to reconcile the multi time-scale measurements in distribution systems. Here, the proposed framework is capable of aggregating the multi-time scale measurements batch-wise or in real-time. Following the aggregation of the multi time-scale measurements, the spatial states of the consistent time-series are estimated using matrix completion based DSSE approach. Simulation results on IEEE 37 and IEEE 123 bus test systems illustrate the efficiency of the proposed methods from the standpoint of both multi time-scale data aggregation and DSSE.

42 ENGINEERING↗
NASA NTRS1986

On self-preserving, variable-density, turbulent free jets

Published experimental data on incompressible, compresible, free binary, and confined binary turbulent axisymmetric jet flows are compiled and characterized, and the effect of varying turbulent diffusivity across the mixing region of a free jet is investigated analytically, applying the similarity-solution approach of So and Hwang (1986) to the self-preserving region. It is shown that closed-form solutions, represented by Gaussian error functions and having the turbulent Reynolds number and a profile-shape factor as free parameters, can be obtained if the turbulent diffusivities of momentum, mass, or heat are assumed to be different and to vary in both the streamwise and radial directions. An entrainment function uniquely related to the turbulent Reynolds number is derived, and good agreement between theoretical predictions and experimental measurements is demonstrated in graphs.

So, R. M. C.↗
NASA NTRS2004

Synthesizing 3D Surfaces from Parameterized Strip Charts

We believe 3D information visualization has the power to unlock new levels of productivity in the monitoring and control of complex processes. Our goal is to provide visual methods to allow for rapid human insight into systems consisting of thousands to millions of parameters. We explore this hypothesis in two complex domains: NASA program management and NASA International Space Station (ISS) spacecraft computer operations. We seek to extend a common form of visualization called the strip chart from 2D to 3D. A strip chart can display the time series progression of a parameter and allows for trends and events to be identified. Strip charts can be overlayed when multiple parameters need to visualized in order to correlate their events. When many parameters are involved, the direct overlaying of strip charts can become confusing and may not fully utilize the graphing area to convey the relationships between the parameters. We provide a solution to this problem by generating 3D surfaces from parameterized strip charts. The 3D surface utilizes significantly more screen area to illustrate the differences in the parameters and the overlayed strip charts, and it can rapidly be scanned by humans to gain insight. The selection of the third dimension must be a parallel or parameterized homogenous resource in the target domain, defined using a finite, ordered, enumerated type, and not a heterogeneous type. We demonstrate our concepts with examples from the NASA program management domain (assessing the state of many plans) and the computers of the ISS (assessing the state of many computers). We identify 2D strip charts in each domain and show how to construct the corresponding 3D surfaces. The user can navigate the surface, zooming in on regions of interest, setting a mark and drilling down to source documents from which the data points have been derived. We close by discussing design issues, related work, and implementation challenges.

Robinson, Peter I.↗
DOE OSTI2020

WEC fault modelling and condition monitoring: A graph-theoretic approach

The nature of wave resources usually requires wave energy converter (WEC) components to handle peak loads (i.e., torques, forces, and powers) that are many times greater than their average loads, accelerating equipment degradation. Moreover, due to their isolated nature and harsh operating environment, WEC systems are projected to possess high operations and maintenance (O&M) cost, i.e., around 27% of their leveled cost of energy. As such, developing techniques to mitigate these costs through the application of condition monitoring and fault tolerant control will significantly impact the economic feasibility of grid connected WEC power. Toward this goal, models of faulty components are developed in the open source modeling platform, WEC-Sim, to estimate the performance and measurable states of a WEC operating with likely device and sensor failures. Two types of faulty component models are then applied to a point absorber WEC model with basic controller damping and spring forces. Resulting changes in device behavior are recorded as a benchmark, and a graph-theoretic approach is proposed for fault detection and identification utilizing multivariate time series. Simulation results demonstrate that these faults can greatly affect the WEC performance, and that the proposed method can effectively detect and classify different types of faults.

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

Sparse Approximate Multifrontal Factorization with Butterfly Compression for High-Frequency Wave Equations

In this work, we present a fast and approximate multifrontal solver for large-scale sparse linear systems arising from finite-difference, finite-volume or finite-element discretization of high-frequency wave equations. The proposed solver leverages the butterfly algorithm and its hierarchical matrix extension for compressing and factorizing large frontal matrices via graph-distance guided entry evaluation or randomized matrix-vector multiplication-based schemes. Complexity analysis and numerical experiments demonstrate $\mathcal{O}(N\log^2 N)$ computation and $\mathcal{O}(N)$ memory complexity when applied to an $N\times N$ sparse system arising from 3D high-frequency Helmholtz and Maxwell problems.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Dynamic Graph Sequence Data from Simulated Neutron Reflectometry Measurements

This dataset comprises dynamic graph sequences derived from simulated in-situ neutron reflectometry measurements, capturing the gradual evolution of a layer structure over time. Each graph sequence represents a synthetic sample, with node features detailing the scattering vector and corresponding reflectivity measurements, while adjacency matrices have corresponding reference material parameters attached as metadata. The dataset spans multiple sets, each with a different number of sequences, offering a comprehensive basis for training models that handle dynamic input sequences with embedded physics. This dataset is particularly suited for tackling inverse problems with hidden physical states that evolve over time, challenges that are typically difficult to address using conventional iterative fitting methods.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Generalize aerodynamic coefficient table storage, checkout and interpolation for aircraft simulation

The set of programs described has been used for rapidly introducing, checking out and very efficiently using aerodynamic tables in complex aircraft simulations on the IBM 360. The preprocessor program reads in tables with different names and dimensions and stores then on disc storage according to the specified dimensions. The tables are read in from IBM cards in a format which is convenient to reduce the data from the original graphs. During table processing, new auxiliary tables are generated which are required for table cataloging and for efficient interpolation. In addition, DIMENSION statements for the tables as well as READ statements are punched so that they may be used in other programs for readout of the data from disc without chance of programming errors. A quick data checking graphical output for all tables is provided in a separate program.

Neuman, F.↗
NASA NTRS1983

The gas-grain interaction in the interstellar medium - Thermal accommodation and trapping

The paper develops a numerical model for calculating thermal accommodation coefficients alpha sub T and trapping functions f sub t for gases incident on solid surfaces. The method is especially designed for astrophysical applications in that it treats economically and with moderate accuracy (+ or - 20%) the dependences of alpha sub T and f sub t on finite and different surface and gas temperatures for a large number of gas-surface combinations. In particular, the method is applied to the astrophysical combinations of hydrogen and helium gases incident on graphite, silicon, and ice surfaces. Graphs are presented of the dependence of alpha sub T and f sub t on interstellar gas temperatures in the range of 10 to 10,000 K and grain temperatures in the range 10 to 1000 K, assuming the current estimates of the gas-surface physical parameters such as the composition and the Debye temperature of the grain material, the repulsive range of the surface potential, and the gas-grain adsorption energy.

Burke, J. R.↗
NASA NTRSDate not supplied

NASA Life Sciences Portal (NLSP): Supporting Scientific Transparency and Reproducibility

NASA’s Life Sciences Ports (NLSP) serves the scientific community by providing curated data from space life science experiment. The Human Research Program (HRP) with the help of NLSP is currently transforming their life sciences data archive systems and processes to improve compliance with the FAIR principles [1]. Some of these improvements will at the same time support the twin pillars of Open Science [2]: transparency of methods and reproducibility of results. Scientific transparency is marked by the easily intelligible communication of what has been investigated: what were the procedures for collecting sample and the characteristics of samples collected? what kinds of measurements were made, what were the environmental conditions of the measurements? What were the analysis techniques of the collected data? Reproducibility of the results and findings from the investigation requires a high level of transparency for all but the simplest investigations; the slightest deviation in communicating and replicating complex experimental procedures or data analyses can often yield quite different data and even findings, thwarting their validation. One of the ways the NLSP is aiming to improve the communication of scientific information is through the use of ontology-driven metadata. Ontologies are powerful, graph-based knowledge representation structures, which can be leveraged to increase data interoperability, the area of the FAIR principles in which many data systems most lack compliance. Over the past decade, there has been a concerted effort in the biomedical community to develop modular and narrowly focused domain and application-specific ontologies in a common, open-source framework, the Open Biological and Biomedical Ontology (OBO) Foundry [3]. The open sharing and modular nature of this effort promises huge increases in harmonized data sharing for systems that leverage these models. Which is in line with the FAIR Data Principles of Findability, Accessibility, Interoperability, and Reuse for scientific data management and stewardship. 1. Wilkinson, M.D., et al., The FAIR Guiding Principles for scientific data management and stewardship. Sci Data, 2016. 3: p. 160018. 2. National Academies of Sciences, E. and Medicine, Open Science by Design: Realizing a Vision for 21st Century Research. 2018, Washington, DC: The National Academies Press. 232. 3. Smith, B., et al., The OBO Foundry: coordinated evolution of ontologies to support biomedical data integration. Nat Biotechnol, 2007. 25(11): p. 1251-5.

Life Sciences data↗
NASA NTRSDate not supplied

NASA Life Sciences Portal (NLSP): Supporting Scientific Transparency and Reproducibility

NASA’s Life Sciences Ports (NLSP) serves the scientific community by providing curated data from space life science experiment. The Human Research Program (HRP) with the help of NLSP is currently transforming their life sciences data archive systems and processes to improve compliance with the FAIR principles [1]. Some of these improvements will at the same time support the twin pillars of Open Science [2]: transparency of methods and reproducibility of results. Scientific transparency is marked by the easily intelligible communication of what has been investigated: what were the procedures for collecting sample and the characteristics of samples collected? what kinds of measurements were made, what were the environmental conditions of the measurements? What were the analysis techniques of the collected data? Reproducibility of the results and findings from the investigation requires a high level of transparency for all but the simplest investigations; the slightest deviation in communicating and replicating complex experimental procedures or data analyses can often yield quite different data and even findings, thwarting their validation. One of the ways the NLSP is aiming to improve the communication of scientific information is through the use of ontology-driven metadata. Ontologies are powerful, graph-based knowledge representation structures, which can be leveraged to increase data interoperability, the area of the FAIR principles in which many data systems most lack compliance. Over the past decade, there has been a concerted effort in the biomedical community to develop modular and narrowly focused domain and application-specific ontologies in a common, open-source framework, the Open Biological and Biomedical Ontology (OBO) Foundry [3]. The open sharing and modular nature of this effort promises huge increases in harmonized data sharing for systems that leverage these models. Which is in line with the FAIR Data Principles of Findability, Accessibility, Interoperability, and Reuse for scientific data management and stewardship.

Life Sciences data↗