Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “deviated”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Flight crew performance when pilot-flying and pilot-not-flying duties are exchanged

This study compares reports from the ASRS database depicting operational anomalies related to flight crew performance when pilot-flying and pilot-not-flying duties were exchanged. A greater number of near midair collisions, takeoff anomalies, and crossing altitude deviations were reported when the Captain was flying. More altitude deviations, near midair collisions during approach, and landing incidents occurred when the First Officer was flying. There were differences in monitoring effectiveness and in the type and distribution of information transfer problems associated with the anomalies. In addition, a number of crew performance factors were noted that were not affected by the exchange of duties. Several of these were deemed important enough to be included as matter of general interest.

Orlady, H. W.↗

Microwave holographic surface measurement of the Tidbinbilla 64-m antenna

The use of a holographic technique for accurately measuring the surface figure of the Tidbinbilla (Canberra, Australia) 64-m antenna is described. Described by Bennet et al. (1976) and Scott and Ryle (1977), the technique consists of measuring the complex far-field response of the antenna at a single frequency using a terrestrial, satellite-borne or celestial radiation source of small angular diameter. This two-dimensional pattern is then Fourier transformed to yield the complex illumination function across the antenna aperture; antenna surface deviations are manifested as phase fluctuations in this function. The speed and low cost of using the technique are real advantages where observing schedules with the telescopes are heavily subscribed. For the 64-m antenna, the unweighted rms surface deviation is found to be about 1.8 mm; when weighted by the radial amplitude taper it is about 1.1 mm. Two earlier estimates by other methods had yielded tolerances of about 1.2 mm rms and 1.1 mm rms. It is planned to use the technique to survey the 22-m antennas of the Australian Telescope accurate to approximately 0.1 mm rms near 10 Ghz.

Rahmat-Samii, Y.↗

Development and flight test of an X-band precision approach concept for remote-area rotorcraft operations

A novel airborne radar-based precision approach concept was developed and flight tested as a part of NASA's Rotorcraft All-Weather Operations Research Program. A demonstration, transponder-based beacon landing system (BLS), incorporating state-of-the-art X-band radar technology and digital processing techniques, was built and flight tested to demonstrate the concept feasibility. The BLS airborne hardware consists of an add-on microprocessor, installed in conjunction with the aircraft weather/mapping radar, which analyzes the radar beacon receiver returns and determines range, localizer deviation, and glide slope deviation. The ground station is an inexpensive, portable unit which can be quickly deployed at a landing site. Results from the flight test program show that the BLS concept has a significant potential for providing rotorcraft with low-cost, precision, instrument approach capability in remote areas. Previously announced in STAR as N84-10041

Clary, G. R.↗

An analysis of Landsat-4 Thematic Mapper geometric properties

Landsat-4 Thematic Mapper data of Washington, DC, Harrisburg, PA, and Salton Sea, CA were analyzed to determine geometric integrity and conformity of the data to known earth surface geometry. Several tests were performed. Intraband correlation and interband registration were investigated. No problems were observed in the intraband analysis, and aside from indications of slight misregistration between bands of the primary versus bands of the secondary focal planes, interband registration was well within the specified tolerances. A substantial number of ground control points were found and used to check the images' conformity to the Space Oblique Mercator (SOM) projection of their respective areas. The means of the residual offsets, which included nonprocessing related measurement errors, were close to the one pixel level in the two scenes examined. The Harrisburg scene residual mean was 28.38 m (0.95 pixels) with a standard deviation of 19.82 m (0.66 pixels), while the mean and standard deviation for the Salton Sea scene were 40.46 (1.35 pixels) and 30.57 m (1.02 pixels), respectively. Overall, the data were judged to be a high geometric quality with errors close to those targeted by the TM sensor design specifications.

Walker, R. E.↗

Satellite and correlative measurements of stratospheric ozone - Comparison of measurements made by SAGE, ECC balloons, chemiluminescent, and optical rocketsondes

The validity of ozone-profile data from the satellite sensor SAGE was tested in a series of correlative experiments conducted at five fixed sites between 6 deg S and 65 deg N during 1979-1980. The intercomparisons included data taken with electrochemical ozone (ECC) balloonsondes and chemiluminescent and optical rocketsondes. The average mean difference for 17 separate comparisons between the SAGE and ECC balloonsonde observations over the altitudes 18-28 km was 9.3 percent with a standard deviation of 2.8 percent. Excluding comparisons separated by greater than 500 km reduces the average mean difference to 8.9 percent and the standard deviation to 2.1 percent. The average mean difference between SAGE and three optical rocketsonde observations over the altitudes 25-50 km was 11 percent, and between SAGE and two chemiluminescent rocketsondes over the altitudes 20-60 km it was 13.5 percent. Considering the differences in vertical resolution, experimental errors, and ozone time and space gradients, the agreement between SAGE-derived ozone profiles and these correlative measurements is considered very good. In addition, isopleths of ozone mixing ratio versus latitude and altitude are in good agreement with previously published results.

Mccormick, M. P.↗

Estimating Antenna Shape From Far-Field Measurements

Amplitude and phase measurements help characterize nearly paraboloidal reflectors. Deviation of microwave reflector from ideal paraboloidal shape deduced from far-field amplitude and phase measurements with help of theoretical technique referred to as microwave holographic metrology. Technique enables estimation of antenna-surface figure from measurements taken at prescribed number of field points. After determining amount of surface deviation, performance of antenna then improved by properly adjusting surface panels.

Rahmat-Samii, Y.↗

Static jet noise test results of four 0.35 scale-model QCGAT mixer nozzles

As part of the NASA Quiet Clean General Aviation Turbofan (QCGAT) engine mixer-nozzle exhaust system program, static jet exhaust noise was recorded at microphone angles of 45 to 155 deg relative to the nozzle inlet for a conventional profile coaxial nozzle and three 12-lobed coaxial mixer nozzles. Both flows in all four nozzles are internally mixed before being discharged from a single exhaust nozzle. The conventional profile coaxial nozzle jet noise is compared to the current NASA Lewis coaxial jet noise prediction and after applying an adjustment to the predicted levels based on the ratio of the kinetic energy of the primary and secondary flows, the prediction is within a standard deviation of 0.9 dB of the measured data. The mass average (mixed flow) prediction is also compared to the noise data for the three mixer nozzles with a reasonably good fit after applying another kinetic energy ratio adjustment (standard deviation of 0.7 to 1.5 dB with the measured data). The tests included conditions for the full-scale engine at takeoff (T.O.), cutback (86% T.O.) and approach (67% T.O.).

Groesbeck, D. E.↗

Preliminary analysis of selected gas dynamic problems

The VAST computer code was used to analyze SSME main combustion chamber start-up transients and the IUS flow field for a damaged nozzle was investigated to better understand the gas dynamic considerations involved in vehicle problems, the effect of start transients on the nozzle flow field for the SSME, and the possibility that a damaged nozzle could account for the acceleration anomaly noted on IUS burn. The results obtained were compared with a method of characteristics prediction. Pressure solutions from both codes were in very good agreement and the Mach number solution on the nozzle centerline deviates substantially for the high expansions for the SSME. Since this deviation was unexpected, the phenomenon is being further examined.

Prozan, R. J.↗

Orientation and temperature dependence of some mechanical properties of the single-crystal nickel-base superalloy Rene N4. 3: Tension-compression anisotropy

Single crystal superalloy specimens with various crystallographic directions along their axes were tested in compression at room temperature, 650, 760, 870, and 980 deg C. These results are compared with the tensile behavior studied previously. The alloy, Rene N4, was developed for gas turbine engine blades and has the nominal composition 3.7 Al, 4.2 Ti, 4 Ta, 0.5 Nb, 6 W, 1.5 Mo 9 Cr. 7.5 Co, balance Ni, in weight percent. Slip trace analysis showed that primary cube slip occurred even at room temperature for the 111 specimens. With increasing test temperature more orientations exhibited primary cube slip, until at 870 deg C only the 100 and 011 specimens exhibited normal octahedral slip. The yield strength for octahedral slip was numerically analysed using a model proposed by Lall, Chin, and Pope to explain deviations from Schmid's Law in the yielding behavior of a single phase Gamma prime alloy, Ni3(Al, Nb). The Schmid's Law deviations in Rene N4 were found to be largely due to a tension-compression anisotropy. A second effect, which increases trength for orientations away from 001, was found to be small in Rene N4. Analysis of recently published data on the single crystal superalloy PWA 1480 yielded the same result.

Miner, R. V.↗

Derivation of Model Topography

The Fourth-Order model necessitates representation of the topography. The problem of the representation of the topography at grid points is addressed. The attempted was to derive an envelope topography. The TI is obtained by taking local mean plus one standard deviation at each grid point and sigma filtering it. The method was greatly influenced by large standard deviations at steep mountains. The O1 topography is the local mean. The S1 is obtained by Sigma filtering in both latitude and longitude the mean O1. The S2 is when the operation is applied twice and S3 thrice, the Q3 is the sigma filtered local mean of the upper third quantile of the source data.

Balgovind, R. C.↗

The response of ionization chambers to relativistic heavy nuclei

As part of a recent calibration at the LBL Bevalac for the Heavy Nuclei Experiment on HEAO-3, the response of a set of laboratory ionization chambers were compared to beams of 26Fe, 36 Kr, 54Xe, 67 Ho, and 79 Au nuclei at maximum energies ranging from 1666 MeV/amu for Fe to 1049 MeV/amu for Au. The response of these chambers shows a significant deviation from the expected energy dependence, but only a slight deviation from Z squared scaling.

Newport, B. J.↗

The response of ionization chambers to relativistic heavy nuclei

The LBL Bevalac for the Heavy Nuclei Experiment on HEAO-3, compared the response of a set of laboratory ionization chambers to beams of 26Fe, 36Kr, 54Xe, 67 Ho, and 79Au nuclei at maximum energies ranging from 1666 MeV/amu for Fe to 1049 MeV/amu for Au. The response of these chambers shows a significant deviation from the expected energy dependence, but only a slight deviation from Z sq scaling.

Newport, B. J.↗

Multiple spacecraft observations of interplanetary shocks Shock-normal oscillations and their effects

Observations of interplanetary shocks with multiple spacecraft and multiple instruments has permitted the determination of their average shock normals with unprecedented accuracy. Nevertheless, there are still local deviations from the best-fit normal. These deviations in general appear to be less than 5 deg but on occasion can be of the order of 20 deg or more. These fluctuating normals and the fluctuating upstream field can cause variations in the downstream field strength even when the upstream field strength is constant. This behavior has important consequences for the appearance of quasi-parallel shocks. Precursor waves which stand on the shock ramp and do not propagate or are not convected across the shock front do not affect the downstream field.

Russell, C. T.↗

Absolute spectral irradiance measurements of lightning from 375 to 880 nm

The time-integrated emissions from cloud-to-ground lightning have been recorded in the 375-880 nm region, using a spectrometer-detector and multichannel analyzer system capable of absolute spectral irradiance measurements. A schematic drawing of the detector-analyzer system is presented, and the experimental setup is described. A total of ten flashes containing 46 individual strikes were recorded and compared to recordings of 500 flashes from 1981. The average spectral irradiance from 375 to 695 nm for flashes at about 15 km was 3.5 x 10 to the -5th J/sq m per stroke with a standard deviation of 2.0 x 10 to the -5th and a range from 0.7 x 10 to the 0.7-6.8 x 10 to the -5th J/sq m per stroke. The average stroke spectra irradiance from 650 to 880 nm for the same strokes was 1.2 x 10 to the -5th, with a standard deviation of 0.7 x 10 to the -5th and a range from 0.5 to 3.2 x 10 to the -5th J/sq m per stroke. A summary table of spectral irradiance values in 50 nm increment is presented. Analysis of the spectral emission data show that unresolved neutral hydrogen lines (NI) at 744.2 nm were more intense than H-alpha emission at 656.3 nm. The strong emission of a flash with a continuing current was identified as cyanogen (CN) emission.

Orville, R. E.↗

The SEASAT altimeter wet tropospheric range correction revisited

An expanded set of radiosonde observations was used to calculate the wet tropospheric range correction for the brightness temperature measurements of the SEASAT scanning multichannel microwave radiometer (SMMR). The accuracy of the conventional algorithm for wet tropospheric range correction was evaluated. On the basis of the expanded observational data set, the algorithm was found to have a bias of about 1.0 cm, and a standard deviation 2.8 cm. In order to improve the algorithm, the exact linear, quadratic and logarithmic relationships between brightness temperatures and range corrections were determined. Various combinations of measurement parameters were used to reduce the standard deviation between SEASAT SMMR and radiosonde observations to about 2.1 cm. The performance of various range correction formulas is compared in a table.

Tapley, D. B.↗

Climate variability and atmospheric teleconnection from satellite observed cloud fluctuations

To investigate the low-frequency variability of the large-scale circulation over the tropics and its relationship with different regions of the globe, statistics of cloud fluctuations, as inferred from outgoing longwave radiation (OLR) are used. The data consists of seven years of global OLR in a 2.5 x 2.5-deg grid derived from NOAA polar orbiting satellite observations. The time series of area-averaged monthly deviation from the seven-year mean of OLR over an equatorial Central Pacific region is presented. It is shown that positive and negative deviations reflect local drier and wetter than normal conditions, respectively. Consideration is given to teleconnection based on the Central Pacific variations and to southern oscillation contributions.

Lau, K. M.↗

Superconducting electromagnetic actuators for astronomical Fabry-Perot interferometers

Two types of superconducting electromagnetic actuators linear and angular - for precise control of Fabry-Perot spectrometer etalons at liquid helium temperature were manufactured and tested successfully. The linear displacement unit (45 Newtons/Amp) has maximum travel of + or - 44 microns with off-axis deviation of less than 1.5 arcseconds for 15 microns path. The angular unit has maximum tilt of + or - 8 arcminutes and can maintain parallelism of two etalons to better than 0.3 arcsecond of angle by compensating the differential contraction upon cooling and off-axis deviation of the linear displacement unit. These actuators are proving especially useful in low temperature infrared instrumentation where other choices, such as piezoelectric crystals, fail and where essentially zero power dissipation permits low infrared backgrounds to be maintained along with long cryogenic lifetimes.

Nishimura, T.↗

Oscillator strengths of some Ba lines - A treatment including core-valence correlation and relativistic effects

Theoretical calculations of selected excitation energies and oscillator strengths for Ba are presented that overcome the difficulties of previous theoretical treatments. A relativistic effective-core potential treatment is used to account for the relativistic core contraction, but the outermost ten electrons are treated explicitly. Core-valence correlation can be included in this procedure in a rigorous and systematic way through a configuration-interaction calculation. Insight is gained into the importance of relativistic effects by repeating many of the calculations using an all-electron nonrelativistic treatment employing an extended Slater basis set. It is found that the intensity of the intercombination line 3P1-1S0 is accurately determined by accounting for the deviation from LS coupling through spin-orbit mixing with the 1P1 state, and that deviations from the Lande interval rule provide an accurate measure of the degree of mixing.

Bauschlicher, C. W., Jr.↗