Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “design of test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Design and test hardware for a solar array switching unit

This paper describes the control of a pulse width modulated (PWM) type sequential shunt switching unit (SSU) for spacecraft applications. It is found that the solar cell output capacitance has a significant impact on SSU design. Shorting of this cell capacitance by the PWM switch causes input current surges. These surges are minimized by the use of a series filter inductor. The system with a filter is analyzed for ripple and the control to output-voltage transfer function. Stable closed loop design considerations are discussed. The results are supported by modeling and measurements of loop gain and of closed-loop bus impedance on test hardware for NASA's 120 V Earth Observation System (EOS). The analysis and modeling are also applicable to NASA's 160 V Space Station power system.

Patil, A. R.↗
NASA NTRS1979

Analysis, design, and test of acoustic treatment in a laboratory inlet duct

A suppression prediction program based on the method of modal analysis for spinning mode propagation in a circular duct was used in the analytical design of optimized, multielement, Kevlar bulk-absorber treatment configurations for an inlet duct. The NASA-Langley ANRL anechoic chamber using the spinning mode synthesizer as a sound source was used to obtain in-duct spinning mode measurements, radial mode measurements, and far-field traverses, as well as aerodynamic measurements. The measured suppression values were compared to predicted values, using the in-duct, forward-traveling, radial-mode content as the source for the prediction. The performance of the treatment panels was evaluated from the predicted and measured data. Although experimental difficulties were encountered at the design condition, sufficient information was obtained to confirm the expectation that it is the panel impedance components which are critical to suppression at a single frequency, not the particular construction materials. The agreement obtained between measurement and prediction indicates that the analytical program can be used as an accurate, reliable, and useful design tool.

Kraft, R. E.↗
NASA NTRS1976

Design and test experience with a triply redundant digital fly-by-wire control system

A triplex digital fly-by-wire flight control system was developed and then installed in a NASA F-8C aircraft to provide fail-operative, full authority control. Hardware and software redundancy management techniques were designed to detect and identify failures in the system. Control functions typical of those projected for future actively controlled vehicles were implemented. This paper describes the principal design features of the system, the implementation of computer, sensor, and actuator redundancy management, and the ground test results. An automated test program to verify sensor redundancy management software is also described.

Szalai, K. J.↗
NASA NTRSDate not supplied

Mars Ascent Vehicle Flight Test Mission Design, Analysis, and Instrumentation

The Mars Ascent Vehicle (MAV) will be the first rocket ever to launch off the surface of Mars, inserting Martian regolith samples into orbit. Since the MAV vehicle is a two-stage all-solid rocket with no thrust termination system, orbit in-sertion accuracy is heavily dependent on pre-flight predictions of the motor per-formance and dynamics of the spin-stabilized upper stage (MAV2). Therefore, a flight test of the MAV2 as the final stage on a Black Brant IX sounding rocket from Wallops Flight Facility (WFF) is planned. This paper discusses the mission design, post flight reconstruction approach, and instrumentation package pro-posed to meet the relevant flight test objectives.

MAV↗
NASA NTRSDate not supplied

Mars Ascent Vehicle Flight Test Mission Design, Analysis, and Instrumentation

The Mars Ascent Vehicle (MAV) will be the first rocket ever to launch off the surface of Mars, inserting Martian regolith samples into orbit. Since the MAV vehicle is a two-stage all-solid rocket with no thrust termination system, orbit in-sertion accuracy is heavily dependent on pre-flight predictions of the motor per-formance and dynamics of the spin-stabilized upper stage (MAV2). Therefore, a flight test of the MAV2 as the final stage on a Black Brant IX sounding rocket from Wallops Flight Facility (WFF) is planned. This paper discusses the mission design, post flight reconstruction approach, and instrumentation package pro-posed to meet the relevant flight test objectives.

MAV↗
NASA NTRS2024

Design and Test of the Orion Crew Module Launch Abort System Hatch

The Orion spacecraft is part of NASA’s Artemis program to establish a permanent human presence on the lunar surface and further enable future crewed missions to Mars. One of the key safety features of Orion is the Launch Abort System (LAS) which pulls the Orion Crew Module (CM) away in the event of a launch vehicle malfunction. It was necessary to design a LAS hatch that allows for crew access to the CM during pad operations. This paper describes the background and evolution of the LAS hatch design, the features used to address the crew safety requirements, the testing challenges in preparation for the Artemis crewed missions, and lessons learned.

Hatch↗
NASA NTRS2024

Design and Test of the Orion Crew Module Launch Abort System Hatch

The Orion spacecraft is part of NASA’s Artemis program to establish a permanent human presence on the lunar surface and further enable future crewed missions to Mars. One of the key safety features of Orion is the Launch Abort System (LAS) which pulls the Orion Crew Module (CM) away in the event of a launch vehicle malfunction. It was necessary to design a LAS hatch that allows for crew access to the CM during pad operations. This paper describes the background and evolution of the LAS hatch design, the features used to address the crew safety requirements, the testing challenges in preparation for the Artemis crewed missions, and lessons learned.

Hatch↗
NASA NTRS2010

Reliability of a Test Battery Designed for Quickly and Safely Assessing Diverse Indices of Neuromuscular Function

Spaceflight affects nearly every physiological system. Spaceflight-induced alterations in physiological function translate to decrements in functional performance. Purpose: To develop a test battery for quickly and safely assessing diverse indices of neuromuscular performance. I. Quickly: Battery of tests can be completed in approx.30-40 min. II. Safely: a) No eccentric muscle actions or impact forces. b) Tests present little challenge to postural stability. III. Diverse indices: a) Strength: Excellent reliability (ICC = 0.99) b) Central activation: Very good reliability (ICC = 0.87) c) Power: Excellent reliability (ICC = 0.99) d) Endurance: Total work has excellent reliability (ICC = 0.99) e) Force steadiness: Poor reliability (ICC = 0.20 - 0.60) National

Spiering, Barry A.↗
NASA NTRS1962

DESIGN AND TEST EXPERIENCES WITH INSTABILITY OF MAJOR AIRFRAME COMPONENTS

Two test incidents involving instability of large scale commercially built structures are described. Two classes of structure are discussed; the first, a fuselage with skin designed to buckle at low stress, and the second, a wing whose surface remains unbuckled to failure. The structure in the region of failure is defined and the failures described and illustrated. Insofar as possible, the stresses in the critical area at the time of failure are reported and compared to strength determined by analysis. Both fuselage and wing surfaces were observed to fail in the mode of a medium range column when adequate support was provided by ribs and frames. Initial failure in the wing example was premature due to a design deficiency in rib strength. A clear illustration is given of the effect of rib stiffness on wing surface stability. Adding stiffness to wing ribs increases the limit of surface stability to the theoretical flat panel value.

SHELL STABILITY↗
NASA NTRS1992

NASA preferred reliability-practices for design and test

NASA HQ established the NASA R&M Steering Committee (R&MSC) comprised of membership from each NASA field center. The primary charter of the R&MSC is to obtain, record, and share the best design practices that NASA has applied to successful space flight programs and current design considerations (guidelines) that should enhance flight reliability on emerging programs. The practices and guidelines are being assembled in a living document for distribution to NASA centers and the aerospace community. The document will be updated annually with additional practices and guidelines as contributions from the centers are reviewed and approved by the R&MSC. Practices and guidelines are not requirements, but rather a means of sharing procedures and techniques that a given center and the R&MSC together feel have strong technical merit and application to the design of space-related equipment.

Lisk, Ronald C.↗
NASA NTRS2016

Z-2 Threaded Insert Design and Testing Abstract

The Z-2 Prototype Planetary Extravehicular Space Suit Assembly is a continuation of NASA's Z series of spacesuits. The Z-2 is another step in the NASA's technology development roadmap leading to human exploration of the Martian surface. To meet a more challenging set of requirements than previous suit systems standard design features, such as threaded inserts, have been re-analyzed and improved. NASA's Z-2 prototype space suit contains several components fabricated from an advanced hybrid composite laminate consisting of IM10 carbon fiber and fiber glass. One requirement NASA levied on the suit composites was the ability to have removable, replaceable helicoil inserts to which other suit components would be fastened. An approach utilizing bonded in inserts with helicoils inside of them was implemented. The design of the interface flanges of the composites allowed some of the inserts to be a "T" style insert that was installed through the entire thickness of the laminate. The flange portion of the insert provides a mechanical lock as a redundancy to the adhesive aiding in the pullout load that the insert can withstand. In some locations it was not possible to utilize at "T" style insert and a blind insert was used instead. These inserts rely completely on the bond strength of the adhesive to resist pullout. It was determined during the design of the suit that the inserts did not need to withstand loads induced from pressure cycling but instead tension induced from torqueing the screws to bolt on hardware which creates a much higher stress on them. Bolt tension is determined by dividing the torque on the screw by a k value multiplied by the thread diameter of the bolt. The k value is a factor that accounts for friction in the system. A common value used for k for a non-lubricated screw is 0.2. The k value can go down by as much as 0.1 if the screw is lubricated which means for the same torque, a much larger tension could be placed on the bolt and insert. This paper summarizes testing that was performed to determine a k value for helicoil inserts in the Z2 suit and how the insert design was modified to resist a higher pull out tension.

Rhodes, RIchard↗
NASA NTRSDate not supplied

Design, Fabrication, Testing and Validation of a Ruggedized Fiber Optic Sensing System (FOSS) for Launch Application

Fiber-optic sensors based on fiber Bragg grating (FBG) is desirable for structural health monitoring and is used for various aerospace applications such as measuring strain and temperature, where a single optical fiber can multiplex hundreds of FBG sensors. The National Aeronautics and Space Administration (NASA) Armstrong Flight Research Center (AFRC) (Edwards, California) has been developing an optical fiber-based sensing suite called Fiber Optics Sensing System (FOSS) over the past two decades. Successful strain monitoring flight demonstrations such as the NASA Ikhana (General Atomics, San Diego, California) remotely piloted aircraft and the X-56A Multi-Utility Technology Testbed (Lockheed Martin Corporation, Bethesda, Maryland) remotely piloted subscale aircraft have been performed. Interest in adapting fiber-optic sensors for aerospace applications has led to commissioning the development of a ruggedized FOSS system for spaceflight through the NASA Launch Services Program (LSP) at the NASA Kennedy Space Center (KSC) (Merritt Island, Florida). In this paper, a ruggedized FOSS suitable for a launch environment is discussed in detail. Thermal analysis and enclosure design will be discussed as well as environmental testing such as shock, random vibration, thermal vacuum, and electromagnetic interference/electromagnetic compatibility (EMI/EMC). With all relevant environmental testing completed, a ruggedized FOSS unit has successfully passed all testing and is now deemed space-launch ready.

Allen R. Parker, Jr↗
NASA NTRS1982

Ceramic high temperature receiver design and tests

The High Temperature Solar Thermal Receiver, which was tested a Edwards AFB, CA during the winter of 1980-1981, evolved from technologies developed over a five year period of work. This receiver was tested at the Army Solar Furnace at White Sands, NM in 1976. The receiver, was tested successfully at 1768 deg F and showed thermal efficiencies of 85%. The results were sufficiently promising to lead ERDA to fund our development and test of a 250 kW receiver to measure the efficiency of an open cavity receiver atop a central tower of a heliostat field. This receiver was required to be design scalable to 10, 50, and 100 MW-electric sizes to show applicability to central power tower receivers. That receiver employed rectagular silicon carbide panels and vertical stanchions to achieve scalability. The construction was shown to be fully scalable; and the receiver was operated at temperatures up to 2000 deg F to achieve the performance goals of the experiment during tests at the GIT advanced components test facility during the fall of 1978.

Davis, S. B.↗
NASA NTRS2020

Model Design and Pre-Test CFD Analysis for a Supersonic Retropropulsion Wind Tunnel Test

Future Mars human lander missions will require using powered descent beginning at supersonic conditions, something which has never been done before at Mars. Significant aerosciences challenges exist due to interactions between the retrorocket exhaust plumes and the freestream flow that alter the aerodynamic behavior of the powered descent vehicle. Historically, wind tunnel tests have been used to study supersonic retropropulsion with inert gas exhaust simulants. Also, SpaceX has successfully decelerated the Falcon 9 first stage numerous times by using powered flight at supersonic conditions. On the computational side, Reynolds-Averaged Navier-Stokes flowfield simulations are regularly completed at full-scale conditions. However, the available ground and flight data do not provide a basis for calibrating the computational uncertainties for aerodynamic interference forces and moments on proposed Mars descent vehicles, either because of insufficient data or dissimilar vehicles geometries and/or conditions. Thus, additional ground testing is needed to continue addressing the aerosciences risks for large-scale human Mars landers. To that end, a retropropulsion wind tunnel test will be conducted in the NASA Langley Unitary Plan Wind Tunnel in 2020. The test is designed to improve upon similar past tests, both in terms of model design and measured data. The test campaign will use subscale model geometries derived from the two current NASA powered descent reference vehicles: a blunt low lift-to-drag vehicle and a more slender geometry. This paper covers the reference vehicles, test objectives, model design, scaling parameters, test matrix, and computational analysis to date.

Karl T Edquist↗
NASA NTRS1980

Minimum Energy Test Direction Design in the Control of Cryogenic Wind Tunnels

The advent of the cryogenic wind tunnel concept is attributable to the need for high Reynolds number flow in wind tunnels. The cryogenic wind tunnel concept consists of operating the test medium of a conventional tunnel at cryogenic temperatures down to 80 K. Nitrogen gas, cooled by injected liquid nitrogen, proves to be ideal for the cryogenic tunnel test medium because of its near perfect behavior in insentropic flow. Cryogenic operation of a wind tunnel results in reduced fan power consumption and no penalty in flow dynamic pressure. In a cryogenic tunnel, the flow parameters (Reynolds number, Mach number and flow dynamic pressure) can be independently controlled by separately controlling the tunnel flow variables: total temperature, test section mass flow, and the tunnel total pressure. The problem of closed-loop control of the tunnel total temperature, flow Mach number, and total pressure is addressed and reported.

Balakrishna, S.↗
NASA NTRS1990

Design and test of a compact optics system for the pool boiling experiment

The experiment described seeks to improve the understanding of the fundamental mechanisms that constitute nucleate pool boiling. The vehicle for accomplishing this is an investigation, including tests to be conducted in microgravity and coupled with appropriate analyses, of the heat transfer and vapor bubble dynamics associated with nucleation, bubble growth/collapse and subsequent motion, considering the interrelations between buoyancy, momentum and surface tension which will govern the motion of the vapor and surrounding liquid, as a function of the heating rate at the heat transfer surface and the temperature level and distribution in the bulk liquid. The experiment is designed to be contained within the confines of a Get-Away-Special Canister (GAS Can) installed in the bay of the space shuttle. When the shuttle reaches orbit, the experiment will be turned on and testing will proceed automatically. In the proposed Pool Boiling Experiment a pool of liquid, initially at a precisely defined pressure and temperature, will be subjected to a step imposed heat flux from a semitransparent thin-film heater forming part of one wall of the container such that boiling is initiated and maintained for a defined period of time at a constant pressure level. Transient measurements of the heater surface and fluid temperatures near the surface will be made, noting especially the conditions at the onset of boiling, along with motion photography of the boiling process in two simultaneous views, from beneath the heating surface and from the side. The conduct of the experiment and the data acquisition will be completely automated and self-contained. For the initial flight, a total of nine tests are proposed, with three levels of heat flux and three levels of subcooling. The design process used in the development and check-out of the compact photographic/optics system for the Pool Boiling Experiment is documented.

Ling, Jerri S.↗
NASA NTRS1984

Some real-time simulation applications to Space Shuttle approach and landing design and test

In the present discussion of the roles played by real time, man-in-the-loop engineering simulation in the development of NASA Space Shuttle approaches and landings, attention is given to the function of the simulator as a design and verification tool. Aspects of the problem posed by Shuttle landings, and the difficulties involved in this problem's quantification, are noted. Recent results of control system studies for pitch axis control, using fixed- and motion-base simulators, are discussed.

Law, H. G., III↗
NASA NTRS1983

The effect of cell design and test criteria on the series/parallel performance of nickel cadmium cells and batteries

Three batteries were operated in parallel from a common bus during charge and discharge. SMM utilized NASA Standard 20AH cells and batteries, and LANDSAT-D NASA 50AH cells and batteries of a similar design. Each battery consisted of 22 series connected cells providing the nominal 28V bus. The three batteries were charged in parallel using the voltage limit/current taper mode wherein the voltage limit was temperature compensated. Discharge occurred on the demand of the spacecraft instruments and electronics. Both flights were planned for three to five year missions. The series/parallel configuration of cells and batteries for the 3-5 yr mission required a well controlled product with built-in reliability and uniformity. Examples of how component, cell and battery selection methods affect the uniformity of the series/parallel operation of the batteries both in testing and in flight are given.

Halpert, G.↗