Results for “departure time” — Page 24

NASA NTRS2019

Alternatives for Scheduling Departures for Efficient Surface Metering in ATD-2: Exploration in a Human-in-the-Loop Simulation

A Human-in-the-Loop (HITL) simulation was conducted to explore whether Ramp Controllers at Charlotte Douglas International Airport (CLT) could both release departing aircraft at an advised time at the gate and also meet an advised time at the spot, where Air Traffic Control (ATC) takes control. Three conditions were compared: (1) Baseline, with no scheduling advisories, (2) instructions to meet advisory times at the gate only, and (3) instructions to meet advisory times at both the gate and the spot. Surprisingly, results showed increased compliance with advisories at the spot in the second condition. This was likely due to increased ramp congestion in the third condition as well as higher Ramp Controller workload and lower situation awareness. Instructing Ramp Controllers to meet scheduling times at the spots, in addition to the gates, is therefore not likely to improve surface scheduling predictability at CLT and may indeed worsen it.

airport surface scheduling↗

NASA NTRS1990

Analysis of exhaustive limited service for token ring networks

Token ring operation is well-understood in the cases of exhaustive, gated, gated limited, and ordinary cyclic service. There is no current data, however, on queueing models for the exhaustive limited service type. This service type differs from the others in that there is a preset maximum (omega) on the number of packets which may be transmitted per token reception, and packets which arrive after token reception may still be transmitted if the preset packet limit has not been reached. Exhaustive limited service is important since it closely approximates a timed token service discipline (the approximation becomes exact if packet lengths are constant). A method for deriving the z-transforms of the distributions of the number of packets present at both token departure and token arrival for a system using exhaustive limited service is presented. This allows for the derivation of a formula for mean queueing delay and queue lengths. The method is theoretically applicable to any omega. Fortunately, as the value of omega becomes large (typically values on the order of omega = 8 are considered large), the exhaustive limited service discipline closely approximates an exhaustive service discipline.

Peden, Jeffery H.↗

NASA NTRSDate not supplied

ATD-2 Field Evaluation of Pre-Departure Trajectory Option Set Reroutes in North Texas Metroplex

The NASA Airspace Technology Demonstration-2 Phase 3 capabilities extend Integrated Arrival, Departure and Surface scheduling to a Metroplex environment where multiple airports are interacting and sharing resources along the terminal boundary. The Phase 3 coordinated scheduling provides pre-departure reroute recommendations to ﬂight operators which reduce delay caused by terminal restrictions. This paper reports results of the Phase 3 Stormy 2021 Field Evaluation conducted between November 2020 and September 2021 in the North Texas Metroplex. During the ﬁeld evaluation NASA partnered with the FAA, American Airlines, Southwest Airlines, and Envoy Airlines to evaluate Phase 3 capabilities in an operational environment. The beneﬁts results are provided as delay savings metrics measured in time and converted to fuel and emissions savings using detailed fuel ﬂow models provided by ﬂight operators.

ATD-2↗

NASA NTRS2018

Simulation Evaluations of an Autonomous Urban Air Mobility Network Management and Separation Service

This paper presents an initial implementation of an autonomous Urban Air Mobility network management and aircraft separation service for urban airspace that does 1) departure and arrival scheduling across the network, 2) continuous trajectory management to ensure safe separation between aircraft, and 3) seamless integration with traditional operations. The highly-autonomous AutoResolver algorithm developed for traditional aviation was extended to provide these capabilities. An evaluation of this initial implementation was conducted in fast-time simulations using a dense, two-hour traffic scenario with Urban Air Mobility aircraft flying between a network of 20 vertiports in the Dallas-Fort Worth metroplex. When the spatial separation was reduced from 0:3nmi to 0:1nmi, the total de- lay decreased by 7:3%; when the temporal separation was reduced from 60s to 45s, the total delay decreased by 28:4%. The total number of conflict resolutions decreased by 26% and 17%, respectively. Furthermore, when a scheduling horizon greater than the duration of UAM flights was used (50min), most conflicts were resolved pre-departure producing ground delay. By comparison, when a shorter scheduling horizon was used (8min), most conflicts were resolved post-departure generating airborne delay. For all scheduling and separation constraints tested, AutoResolver prevented loss of separation from occurring. Urban Air Mobility operations have the ability to revolutionize how people and goods are transported and this paper presents initial research focusing on the high levels of autonomy required for an airspace system capable of scaling to handle significantly higher densities of aircraft.

Bosson, Christabelle S.↗

NASA NTRSDate not supplied

Overview of an Exploratory, Real-Time, Multi-Pilot Simulation Study of Early eVTOL Operations at Non-Towered Vertiports

This paper provides a report out on an exploratory, multi-aircraft/multi-pilot, real-time simulation study conducted by NASA of early commercial powered-lift, Urban Air Mobility (UAM) operations at a non-towered vertiport. As used in this paper, vertiport refers to the primary ground and airspace elements facilitating the takeoff and landing of electric vertical takeoff and landing (eVTOL) aircraft with central emphasis on a vertipad, i.e. the physical touch-down and lift-off area and surrounding approach , departure, local pattern procedures. The study, known as the Piloted UML-2 ConOps Study (PUCS), had two high-level goals. The first goal was providing preliminary insights and observations relevant to the piloting and flight operations of early, commercial UAM operations aligned with the initial stage of the FAA’s Advanced Air Mobility (AAM) Implementation Plan and the second level NASA’s UAM Maturity Level (UML) scale. The second goal was evaluating a novel, medium-fidelity, extensible, many-pilot, real-time simulation capability known as the UAM Flyers developed by NASA. The Flyers are intended to allow rapid development, screening, evaluation, and demonstrations of potential Concepts of Operation (ConOps) for UAM flight operations and airspace management in a modular and low-cost, real-time, human-in-the-loop rapid simulation prototyping environment. For this study, ten Flyer cockpits were configured to evaluate flight operations through a non-towered vertiport with pilot interfaces and displays (external and in-cockpit) appropriate for operations under visual flight rules (VFR) and employing flight and communication procedures representative of current operations at non-towered airports. The presented results include an achieved operational tempo; durations of individual flight tasks for approaches and departures; off-nominal events and triggers; and pilot comments regarding potential procedural and technology improvements.

Urban Air Mobility↗

NASA NTRSDate not supplied

Overview of an Exploratory, Multi-Pilot Simulation Study of Early eVTOL Operations at Non-Towered Vertiports

This paper provides a report out on an exploratory, multi-aircraft/multi-pilot, real-time simulation study conducted by NASA of early commercial powered-lift, Urban Air Mobility (UAM) operations at a non-towered vertiport. As used in this paper, vertiport refers to the primary ground and airspace elements facilitating the takeoff and landing of electric vertical takeoff and landing (eVTOL) aircraft with central emphasis on a vertipad, i.e. the physical touch-down and lift-off area and surrounding approach , departure, local pattern procedures. The study, known as the Piloted UML-2 ConOps Study (PUCS), had two high-level goals. The first goal was providing preliminary insights and observations relevant to the piloting and flight operations of early, commercial UAM operations aligned with the initial stage of the FAA’s Advanced Air Mobility (AAM) Implementation Plan and the second level NASA’s UAM Maturity Level (UML) scale. The second goal was evaluating a novel, medium-fidelity, extensible, many-pilot, real-time simulation capability known as the UAM Flyers developed by NASA. The Flyers are intended to allow rapid development, screening, evaluation, and demonstrations of potential Concepts of Operation (ConOps) for UAM flight operations and airspace management in a modular and low-cost, real-time, human-in-the-loop rapid simulation prototyping environment. For this study, ten Flyer cockpits were configured to evaluate flight operations through a non-towered vertiport with pilot interfaces and displays (external and in-cockpit) appropriate for operations under visual flight rules (VFR) and employing flight and communication procedures representative of current operations at non-towered airports. The presented results include an achieved operational tempo; durations of individual flight tasks for approaches and departures; off-nominal events and triggers; and pilot comments regarding potential procedural and technology improvements.

Urban Air Mobility↗

DOE OSTI2024

CIRCLES: Congestion Impacts Reduction via CAV-in-the-loop Lagrangian Energy Smoothing

The energy efficiency of today’s vehicular mobility relies on the un-integrated combination of i) control via static assets (traffic lights, metering, variable speed limits, etc.); and ii) onboard vehicle automation (adaptive cruise control (ACC), ecodriving, etc.). These two families of control were not co-designed and are not engineered to work in coordination. Recent studies have shown i) limitations of controls, and even ii) negative impacts of ACC. This project focused on the technology development, implementation and prototyping, and validation of Mobile Traffic Control (MTC). MTC can be viewed as an extension of classical traffic control (in which static infrastructure actuates traffic flow). In the MTC paradigm, automated vehicles actuate the entire flow via their behavior, offering enhanced possibilities to optimize the energy footprint of traffic, if designed correctly. We set out to demonstrate for the first time that considerably reduced fuel consumption of all vehicles in traffic can be achieved via distributed control of a small proportion of CAVs. Compared to baseline vehicular technologies, our work offers a significant design departure: control algorithms for the CAVs consider the impact one vehicle can have on overall traffic, improving resulting overall fuel consumption. We focus on using a few vehicles (as traffic controllers via CAV technology) to improve the energy efficiency of traffic flow to further optimize energy efficiency. A live-traffic demonstration in November 2022 featured the deployment of 100 specially-equipped CAVs, constituting an approximate local penetration rate upwards of 2%.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

NASA NTRS1985

Trends in the Southern Hemisphere

The station data of monthly mean sea level pressure, surface air temperature as well as monthly mean upper air rawinsonde observations were used to study the trends in the southern winter (June, July and August) and summer (December, January and February). This study covers the period 1951 to 1981. Most of the surface data have continuous 31 year records, however, for some high latitude stations, both surface and upper air records started in 1957 or even later. The normalized anomaly for a given variable Z is defined as the departure from the 1951 to 1981 grand mean divided by the standard deviation during the same period. To eliminate the large fluctuations in the data, the 1-3-1 smoothing was applied to the time series of normalized anomalies. The trends of monthly mean temperatures and height from the surface to 200 mb level is documented.

Mo, K. C.↗

NASA NTRS1992

Non-LTE radiating acoustic shocks and Ca II K2V bright points

We present, for the first time, a self-consistent solution of the time-dependent 1D equations of non-LTE radiation hydrodynamics in solar chromospheric conditions. The vertical propagation of sinusoidal acoustic waves with periods of 30, 180, and 300 s is calculated. We find that departures from LTE and ionization recombination determine the temperature profiles of the shocks that develop. In LTE almost all the thermal energy goes into ionization, so the temperature rise is very small. In non-LTE, the finite transition rates delay the ionization to behind the shock front. The compression thus goes into thermal energy at the shock front leading to a high temperature amplitude. Further behind the shock front, the delayed ionization removes energy from the thermal pool, which reduces the temperature, producing a temperature spike. The 180 s waves reproduce the observed temporal changes in the calcium K line profiles quite well. The observed wing brightening pattern, the violet/red peak asymmetry and the observed line center behavior are all well reproduced. The short-period waves and the 5 minute period waves fail especially in reproducing the observed behavior of the wings.

Carlsson, Mats↗

NASA NTRS1994

Hydro-isostatic deflection and tectonic tilting in the central Andes: Initial results of a GPS survey of Lake Minchin shorelines

Sufficiently large lake loads provide a means of probing rheological stratification of the crust and upper mantle. Lake Minchin was the largest of the late Pleistocene pluvial lakes in the central Andes. Prominent shorelines, which formed during temporary still-stands in the climatically driven lake level history, preserve records of lateral variations in subsequent net vertical motions. At its maximum extent the lake was 140 m deep and spanned 400 km N-S and 200 km E-R. The load of surficial water contained in Lake Minchin was sufficient to depress the crust and underlying mantle by 20-40 m, depending on the subjacent rheology. Any other differential vertical motions will also be recorded as departures from horizontality of the shorelines. We recently conducted a survey of shoreline elevations of Lake Minchin with the express intent of monitoring the hydro-isostatic deflection and tectonic tilting. Using real-time differential Global Positioning System (GPS), we measured topographic profiles across suites of shorelines at 15 widely separated locations throughout the basin. Horizontal and vertical accuracies attained are roughly 30 and 70 cm, respectively. Geomorphic evidence suggests that the highest shoreline was occupied only briefly (probably less than 200 years) and radiocarbon dates on gastropod shells found in association with the shore deposits constrain the age to roughly 17 kyr. The basin-side pattern of elevations of the highest shoreline is composed of two distinct signals: (27 +/- 1) m of hydro-isostatic deflection due to the lake load, and a planar tilt with east and north components of (6.8 +/- 0.4) 10(exp -5) and 9-5.3 +/- 0.3) 10(exp -5). This rate of tilting is too high to be plausibly attributed to steady tectonism, and presumably reflects some unresolved combination of tectonism plus the effects of oceanic and lacustrine loads on a laterally heterogeneous substrate. The history of lake level fluctuations is still inadequately known to allow detailed inferences of crust and mantle rheology. However, it is already clear that the effective elastic plate thickness is closer to 40 km than the 60-70 km crustal thickness in the central Andes and the effective viscosity is less than 5 10(exp 20) Pa s.

Bills, Bruce G.↗

NASA NTRSDate not supplied

An Artificial Neural Network Approach to Predict Rotor-Airframe Acoustic Waveforms

A surrogate artificial neural network/machine learning model was developed to predict the acoustic interaction for a fixed-pitch rotor in proximity to a downstream cylindrical airframe typical of small Unmanned Aerial System (sUAS) platforms. The model was trained to predict the acoustic waveform under representative hover conditions as a function of rotational speed, airframe proximity, and observer angle. Training data were acquired in an anechoic chamber on both isolated rotors and rotor-airframe configurations. Acoustic amplitude and phase of the revolution-averaged interaction were predicted, which required up to 25 harmonics to capture the impulse event caused by the blade’s approach and departure from the airframe. Prediction performance showed, on average, that the models could estimate the acoustic amplitude and phase over the relevant harmonics for unseen conditions with 86% and 75% accuracy, respectively, enabling a time domain reconstruction of the waveform for the range of geometric and flow parameters tested.

acoustics↗

NASA NTRSDate not supplied

An Artificial Neural Network Approach to Predict Rotor-Airframe Acoustic Waveforms

A surrogate artificial neural network/machine learning model was developed to predict the acoustic interaction for a fixed-pitch rotor in proximity to a downstream cylindrical airframe typical of small Unmanned Aerial System (sUAS) platforms. The model was trained to predict the acoustic waveform under representative hover conditions as a function of rotational speed, airframe proximity, and observer angle. Training data were acquired in an anechoic chamber on both isolated rotors and rotor-airframe configurations. Acoustic amplitude and phase of the revolution-averaged interaction were predicted, which required up to 25 harmonics to capture the impulse event caused by the blade’s approach and departure from the airframe. Prediction performance showed, on average, that the models could estimate the acoustic amplitude and phase over the relevant harmonics for unseen conditions with 86% and 75% accuracy, respectively, enabling a time domain reconstruction of the waveform for the range of geometric and flow parameters tested.

acoustics↗

NASA NTRS2012

DataComm in Flight Deck Surface Trajectory-Based Operations

The purpose of this pilot-in-the-loop aircraft taxi simulation was to evaluate a NextGen concept for surface trajectory-based operations (STBO) in which air traffic control (ATC) issued taxi clearances with a required time of arrival (RTA) by Data Communications (DataComm). Flight deck avionics, driven by an error-nulling algorithm, displayed the speed needed to meet the RTA. To ensure robustness of the algorithm, the ability of 10 two-pilot crews to meet the RTA was tested in nine experimental trials representing a range of realistic conditions including a taxi route change, an RTA change, a departure clearance change, and a crossing traffic hold scenario. In some trials, these DataComm taxi clearances or clearance modifications were accompanied by preview information, in which the airport map display showed a preview of the proposed route changes, including the necessary speed to meet the RTA. Overall, the results of this study show that with the aid of the RTA speed algorithm, pilots were able to meet their RTAs with very little time error in all of the robustness-testing scenarios. Results indicated that when taxi clearance changes were issued by DataComm only, pilots required longer notification distances than with voice communication. However, when the DataComm was accompanied by graphical preview, the notification distance required by pilots was equivalent to that for voice.

Bakowski, Deborah L.↗

NASA NTRS2012

DataComm in Flight Deck Surface Trajectory-Based Operations

The purpose of this pilot-in-the-loop aircraft taxi simulation was to evaluate a NextGen concept for surface trajectory-based operations (STBO) in which air traffic control (ATC) issued taxi clearances with a required time of arrival (RTA) by Data Communications (DataComm). Flight deck avionics, driven by an error-nulling algorithm, displayed the speed needed to meet the RTA. To ensure robustness of the algorithm, the ability of 10 two-pilot crews to meet the RTA was tested in nine experimental trials representing a range of realistic conditions including a taxi route change, an RTA change, a departure clearance change, and a crossing traffic hold scenario. In some trials, these DataComm taxi clearances or clearance modifications were accompanied by 'preview' information, in which the airport map display showed a preview of the proposed route changes, including the necessary speed to meet the RTA. Overall, the results of this study show that with the aid of the RTA speed algorithm, pilots were able to meet their RTAs with very little time error in all of the robustness-testing scenarios. Results indicated that when taxi clearance changes were issued by DataComm only, pilots required longer notification distances than with voice communication. However, when the DataComm was accompanied by graphical preview, the notification distance required by pilots was equivalent to that for voice.

NextGen↗

DOE OSTI2023

The future of the El Niño–Southern Oscillation: using large ensembles to illuminate time-varying responses and inter-model differences

Future changes in the El Niño–Southern Oscillation (ENSO) are uncertain, both because future projections differ between climate models and because the large internal variability of ENSO clouds the diagnosis of forced changes in observations and individual climate model simulations. By leveraging 14 single model initial-condition large ensembles (SMILEs), we robustly isolate the time-evolving response of ENSO sea surface temperature (SST) variability to anthropogenic forcing from internal variability in each SMILE. We find nonlinear changes in time in many models and considerable inter-model differences in projected changes in ENSO and the mean-state tropical Pacific zonal SST gradient. We demonstrate a linear relationship between the change in ENSO SST variability and the tropical Pacific zonal SST gradient, although forced changes in the tropical Pacific SST gradient often occur later in the 21st century than changes in ENSO SST variability, which can lead to departures from the linear relationship. Single-forcing SMILEs show a potential contribution of anthropogenic forcing (aerosols and greenhouse gases) to historical changes in ENSO SST variability, while the observed historical strengthening of the tropical Pacific SST gradient sits on the edge of the model spread for those models for which single-forcing SMILEs are available. Our results highlight the value of SMILEs for investigating time-dependent forced responses and inter-model differences in ENSO projections. The nonlinear changes in ENSO SST variability found in many models demonstrate the importance of characterizing this time-dependent behavior, as it implies that ENSO impacts may vary dramatically throughout the 21st century.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1994

Rapid computation of spectrally integrated non-local thermodynamic equilibrium limb emission

The interpretation of infrared radiance measurements made by satellite-borne limb-scanning broadband radiometers requires accurate and computationally fast techniques with which to evaluate the equation of radiative transfer. This requirement is made even more stringent when analyzing measurements of non-local thermodynamic equilibrium (non-LTE) emission from the terrestrial mesosphere and lower thermosphere. In principle, line-by-line calculations which explicitly account for the departure from thermodynamic equilibrium in both the source functions and the transmittances are necessary. In this paper we extend the emissivity growth approximation (EGA) technique developed for local thermodynamic equilibrium (LTE) limb radiance for the molecular oxygen dayglow (1.27 micrometers and 762 nm), ozone and carbon dioxide in the 9- to 11-micrometer spectral interval, carbon monoxide (4.6 micrometers), nitric oxide (5.3 micrometers), and the carbon dioxide bands (15 micrometers) are presented. Using the non-LTE form of the EGA, the spectrally integrated limb emission is calculated for 35 tangent heights in the mesosphere and lower thermosphere (a total of 1200 atmospheric layers) with line-by-line accuracy in approximately 0.35 s of CPU time on readily available desktop computer hardware, while the corresponding line-by-line calculations may require several minutes. The non-LTE EGA technique will allow kinetic temperature and minor constituend retrieval algorithms to readily include non-LTE efects limited only by the a priori knowledge of the departure from LTE in the observed bands.

Mlynczak, Martin G.↗

NASA NTRS1974

Simulation studies of STOL airplane operations in metropolitan downtown and airport air traffic control environments

The operating problems and equipment requirements for STOL airplanes in terminal area operations in simulated air traffic control (ATC) environments were studied. These studies consisted of Instrument Flight Rules (IFR) arrivals and departures in the New York area to and from a downtown STOL port, STOL runways at John F. Kennedy International Airport, or STOL runways at a hypothetical international airport. The studies were accomplished in real time by using a STOL airplane flight simulator. An experimental powered lift STOL airplane and two in-service airplanes having high aerodynamic lift (i.e., STOL) capability were used in the simulations.

Sawyer, R. H.↗

NASA NTRS1981

A Quasi-Parabolic technique for computation of three-dimensional viscous flows

A computational technique is presented for obtaining flowfield solutions to a parabolic form of the Navier-Stokes equations. The point of departure is the General Interpolant Method (GIM) which provides a discretization for partial differential equations on arbitrary three-dimensional geometries. The new scheme, termed Quasi-Parabolic, treats the parabolized equations but with 'time-like' terms appended. Addition of these extra terms, which are relaxed by iteration, avoid many of the singularities inherent in classical parabolic Navier-Stokes methods. Streamwise derivatives are approximated by three-point backward differences and the cross plane operators use an alternating forward-backward sweep. A two-step sequence is used to implement the difference scheme in the spatial dimensions and a time-like relaxation converges the quasi-parabolic procedure at each plane. Solutions are presented for flows in two and three dimensions. Inviscid flows are solved for internal and external applications and viscous flows in boundary layers and free shear layers are also computed with the GIM/Quasi-Parabolic scheme.

Spradley, L. W.↗