Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “defect passivation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Carrier collection losses in interface passivated amorphous silicon thin-film solar cells

In silicon thin-film solar cells the interface between the i- and p-layer is the most critical. In the case of back diffusion of photogenerated minority carriers to the i/p-interface, recombination occurs mainly on the defect states at the interface. To suppress this effect and to reduce recombination losses, hydrogen plasma treatment (HPT) is usually applied. As an alternative to using state of the art HPT we apply an argon plasma treatment (APT) before the p-layer deposition in n-i-p solar cells. To study the effect of APT, several investigations were applied to compare the results with HPT and no plasma treatment at the interface. Carrier collection losses in resulting solar cells were examined with spectral response measurements with and without bias voltage. To investigate single layers, surface photovoltage and X-ray photoelectron spectroscopy (XPS) measurements were conducted. The results with APT at the i/p-interface show a beneficial contribution to the carrier collection compared with HPT and no plasma treatment. Therefore, it can be concluded that APT reduces the recombination centers at the interface. Further, we demonstrate that carrier collection losses of thin-film solar cells are significantly lower with APT.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Light-emitting Si nanostructures formed in SiO{sub 2} on irradiation with swift heavy ions

SiO{sub 2} layers containing implanted excess Si are irradiated with Xe ions with an energy of 130 MeV and doses of 3 x 10{sup 12}-10{sup 14} cm{sup -2}. In the samples irradiated with a dose of 3 x 10{sup 12} cm{sup -2}, {approx}10{sup 12} cm{sup -2} segregated clusters 3-4 nm in dimension are detected by transmission electron microscopy. With increasing dose, the dimensions and number of these clusters increase. In the photoluminescence spectrum, a 660- to 680-nm band is observed, with the intensity dependent on the dose. After passivation of the sample with hydrogen at 500 deg. C, the band disappears, but a new {approx}780-nm band typical of Si nanocrystals becomes evident. On the basis of the entire set of data, it is concluded that the 660- to 680-nm band is associated with imperfect Si nanocrystals grown in the tracks of Xe ions due to high ionization losses. The nonmonotonic dependence of the photoluminescence intensity on the dose is attributed to the difference between the diameters of tracks and the diameters of the displacements' cascades responsible for defect formation.

36 MATERIALS SCIENCE↗

Utilization of Tabula Rasa to Stabilize Bulk Lifetimes in n-Cz Silicon for High-Performance Solar Cell Processing

We investigate a high temperature, high cooling-rate anneal Tabula Rasa (TR) and report its implications on n-type Czochralski-grown silicon (n-Cz Si) for photovoltaic fabrication. Tabula Rasa aims at dissolving and homogenizing oxygen precipitate nuclei that can grow during the cell process steps and degrade the cell performance due to their high internal gettering and recombination activity. The Tabula Rasa thermal treatment is performed in a clean tube furnace with cooling rates >100 degrees C/s. We characterize the bulk lifetime by Sinton lifetime and photoluminescence mapping just after Tabula Rasa, and after the subsequent cell processing. After TR, the bulk lifetime surprisingly degrades to <; 0.1ms, only to recover to values equal or higher than the initial non-treated wafer (several ms), after typical high temperature cell process steps. Those include boron diffusion and oxidation; phosphorus diffusion/oxidation; ambient annealing at 850 degrees C; and crystallization annealing of tunneling-passivating contacts (doped polycrystalline silicon on 1.5 nm thermal oxide). The drastic lifetime improvement during high temperature cell processing is attributed to improved external gettering of metal impurities and annealing of intrinsic point defects. Time and injection dependent lifetime spectroscopy further reveals the mechanisms of lifetime improvement after Tabula Rasa treatment. Additionally, we report the efficacy of Tabula Rasa on n-type Cz-Si wafers and its dependence on oxygen concentration, correlated to position within the ingot.

14 SOLAR ENERGY↗

Understanding Part to Part Variability During Directed Energy Deposition Processes Using In Situ and Ex Situ Process Characterization

The overall goal of this technical collaboration is the use of in situ and ex situ characterization techniques to understand part to part variability in Ti-6Al-4V parts fabricated using directed energy deposition (DED) process, and subsequently qualify parts fabricated using AM. The primary goal of the Phase-1 of this CRADA was to demonstrate the feasibility of capturing the above changes using a combination of high speed stereo imaging and in situ monitoring using two wavelength pyrometers. The in situ monitoring was then correlated using ex situ characterization performed using optical microscopy. The results from phase-1 clearly show that changes to the process and shielding gases have a significant impact on the geometric conformity of the build and the build layer height. The results from phase-1 show that in addition to using IR thermography as a tool to measure the temperature and gradients, we could use it to monitor the build topography and the layer height and use the information to develop closed loop control systems. The phase-1 results show that there is a narrow zone under which the process must operate in order to be “passively stable” or autocorrect for over building. In addition, the results demonstrate that when operated within this range the build autocorrects and there is a drastic reduction in the interlayer lack of fusion defect formation.

36 MATERIALS SCIENCE↗

Changes in Hydrogen Concentration and Defect State Density at the Poly-Si/SiOx/c-Si Interface Due to Firing

We determined the density of defect states of poly-Si/SiOx/c-Si junctions featuring a wet chemical interfacial oxide from lifetime measurements using the MarcoPOLO model to calculate recombination and contact resistance in poly-Si/SiOx/c-Si-junctions. In samples that did not receive any hydrogen treatment, the Dit,cSi is about 2 × 1012 cm-2 eV1 before firing and rises to 3–7 × 1012 cm2 eV1 during firing at measured peak temperatures between 620 °C and 863 °C. To address the question of why AlOx/SiNy stacks in contrast to pure SiNy layers for hydrogenation during firing provides better passivation quality, we have measured the hydrogen concentrations at the poly-Si/SiOx/c-Si interface as a function of AlOx layer thickness and compared these to J0 and calculated Dit,c-Si values. We observe an increase of the hydrogen concentration at the SiOx/c-Si interface upon firing as a function of the firing temperature that exceeds the defect concentrations at the interface several times. However, the AlOx layer thickness appears to cause an increase in hydrogen concentration at the SiOx/c-Si interface in these samples rather than exhibiting a hydrogen blocking property.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Performance analysis of boron nitride embedded armchair graphene nanoribbon metal–oxide–semiconductor field effect transistor with Stone Wales defects

We study the performance of a hybrid Graphene-Boron Nitride armchair nanoribbon (a-GNR-BN) n-MOSFET at its ballistic transport limit. We consider three geometric configurations 3p, 3p + 1, and 3p + 2 of a-GNR-BN with BN atoms embedded on either side (2, 4, and 6 BN) on the GNR. Material properties like band gap, effective mass, and density of states of these H-passivated structures are evaluated using the Density Functional Theory. Using these material parameters, self-consistent Poisson-Schrodinger simulations are carried out under the Non Equilibrium Green's Function formalism to calculate the ballistic n-MOSFET device characteristics. For a hybrid nanoribbon of width ∼5 nm, the simulated ON current is found to be in the range of 265 μA–280 μA with an ON/OFF ratio 7.1 × 10{sup 6}–7.4 × 10{sup 6} for a V{sub DD} = 0.68 V corresponding to 10 nm technology node. We further study the impact of randomly distributed Stone Wales (SW) defects in these hybrid structures and only 2.5% degradation of ON current is observed for SW defect density of 3.18%.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electronic Structure and Epitaxy of CdTe Shells on InSb Nanowires

Abstract Indium antimonide (InSb) nanowires are used as building blocks for quantum devices because of their unique properties, that is, strong spin‐orbit interaction and large Landé g‐factor. Integrating InSb nanowires with other materials could potentially unfold novel devices with distinctive functionality. A prominent example is the combination of InSb nanowires with superconductors for the emerging topological particles research. Here, the combination of the II–VI cadmium telluride (CdTe) with the III–V InSb in the form of core–shell (InSb–CdTe) nanowires is investigated and potential applications based on the electronic structure of the InSb–CdTe interface and the epitaxy of CdTe on the InSb nanowires are explored. The electronic structure of the InSb–CdTe interface using density functional theory is determined and a type‐I band alignment is extracted with a small conduction band offset ( ⩽0.3 eV). These results indicate the potential application of these shells for surface passivation or as tunnel barriers in combination with superconductors. In terms of structural quality, it is demonstrated that the lattice‐matched CdTe can be grown epitaxially on the InSb nanowires without interfacial strain or defects. These shells do not introduce disorder to the InSb nanowires as indicated by the comparable field‐effect mobility measured for both uncapped and CdTe‐capped nanowires.

36 MATERIALS SCIENCE↗

Influence of Heat Treatments in H 2 and Ar on the E 1 center in β -Gs 2 O 3

In this report the influence of heat treating n-type bulk β-Ga 2 O 3 in hydrogen (H2) and argon (Ar) gases on the presence of the defect level commonly labeled as E 1 was studied. Fourier transform-infrared spectroscopy confirms that hydrogen (H) is incorporated into β-Ga 2 O 3 during H 2 annealing at 900 °C. Deep-level transient spectroscopy measurements reveal that the concentration of the E 1 level is promoted by the introduction of H, in contrast to what is observed in samples heat-treated in an Ar flow. We further find the E 1 level to be stable against heat treatments at 650 K, both with and without an applied reverse-bias voltage. Potential candidates for the defect origin of E 1 are investigated using hybrid-functional calculations, and three types of defect complexes involving H are found to exhibit charge-state transition levels compatible with E 1 , including substitutional H at one of the threefold coordinated O sites, Ga-substitutional shallow donor impurities passivated by H, and certain configurations of singly hydrogenated Ga–O divacancies. Among these types, only the latter exhibit H binding energies that are consistent with the observed thermal stability of E 1 .

36 MATERIALS SCIENCE↗

Hydrogenation of Dislocation-Limited Heteroepitaxial Silicon Solar Cells: Preprint

Post-deposition hydrogenation by remote plasma significantly improves performance of heteroepitaxial silicon solar cells. Heteroepitaxial deposition of thin crystal silicon on sapphire for photovoltaics (PV) is an excellent model system for the study and improvement of deposition on inexpensive Al2O3-coated (100) biaxially-textured metal foils. Without hydrogenation, PV conversion efficienciesare less than 1% on our model system. Performance is limited by carrier recombination at electrically active dislocations that result from lattice mismatch, and other defects. We find that low-temperature hydrogenation at 350 degrees C is more effective than hydrogenation at 610 degrees C. In this work, we use measurements such as spectral quantum efficiency, secondary ion mass spectrometry(SIMS), and vibrational Si-H spectroscopies to understand the effects of hydrogenation on the materials and devices. Quantum efficiency increases most at red and green wavelengths, indicating hydrogenation is affecting the bulk more than the surface of the cells. SIMS shows there are 100X more hydrogen atoms in our cells than dangling bonds along dislocations. Yet, Raman spectroscopy indicatesthat only low temperature hydrogenation creates Si-H bonds; trapped hydrogen does not stably passivate dangling-bond recombination sites at high temperatures.

14 SOLAR ENERGY↗

Surface Passivation and Junction Formation Using Low Energy Hydrogen Implants

New applications for high current, low energy hydrogen ion implants on single crystal and polycrystal silicon grain boundaries are discussed. The effects of low energy hydrogen ion beams on crystalline Si surfaces are considered. The effect of these beams on bulk defects in crystalline Si is addressed. Specific applications of H+ implants to crystalline Si processing are discussed. In all of the situations reported on, the hydrogen beams were produced using a high current Kaufman ion source.

Fonash, S. J.↗

Electrochemical characterization of InP structures

Electrochemical (EC) techniques represent a simple and yet accurate method to characterize InP and related materials structures. With EC techniques, uncertainties in the measurements arising from factors such as surface effects, the composition and thickness of a front dead layer, the contacts, etc., can be significantly reduced when both a suitable electrolyte is used and the measuring conditions are carefully selected. In this work, the use of photoelectrochemical techniques with InP structures is reported. The work focuses on both the characterization and the optimization of structures grown by thermal diffusion and by epitaxial methods. Characterization of the structures is done by studying the variation in the density of surface states, number of defects, and net majority carrier concentration as a function of material removed. A step-by-step optimization process of n(sup +)p and p(sup+)n InP structures is also described. This involves the passivation and subsequent removal of damaged layers in order to extract the performance parameters of solar cells fabricated with these structures.

Faur, Maria↗

Dynamic annealing in Ge studied by pulsed ion beams

The formation of radiation damage in Ge above room temperature is dominated by complex dynamic annealing processes, involving migration and interaction of ballistically-generated point defects. Here, we study the dynamics of radiation defects in Ge in the temperature range of 100–160 °C under pulsed beam irradiation with 500 keV Ar ions when the total ion fluence is split into a train of equal square pulses. By varying the passive portion of the beam duty cycle, we measure a characteristic time constant of dynamic annealing, which rapidly decreases from ~8 to 0.3 ms with increasing temperature. By varying the active portion of the beam duty cycle, we measure an effective diffusion length of ~38 nm at 110 °C. Results reveal a major change in the dominant dynamic annealing process at a critical transition temperature of ~130 °C. The two dominant dynamic annealing processes have an order of magnitude different activation energies of 0.13 and 1.3 eV.

42 ENGINEERING↗

Real-space characterization of reactivity towards water at the B i 2 T e 3 (111) surface

Surface reactivity is important in modifying the physical and chemical properties of surface-sensitive materials, such as the topological insulators. Even though many studies addressing the reactivity of topological insulators towards external gases have been reported, it is still under heavy debate whether and how the topological insulators react with H2O. Here, we employ scanning tunneling microscopy to directly probe the surface reaction of Bi2Te3 towards H2O. Surprisingly, it is found that only the top quintuple layer is reactive to H2O, resulting in a hydrated Bi bilayer as well as some Bi islands, which passivate the surface and prevent subsequent reaction. A reaction mechanism is proposed with H2Te and hydrated Bi as the products. Unexpectedly, our study indicates that the reaction with water is intrinsic and not dependent on any surface defects. Since water inevitably exists, these findings provide key information when considering the reactions of Bi2Te3 with residual gases or atmosphere.

Zhang, Kai-Wen↗

Recent Progress in Nanoelectrical Characterizations of CdTe and Cu(In,Ga)Se2

We report two recent nanoelectrical characterizations of CdTe and Cu(In, Ga)Se 2 (CIGS) thin-film solar cells by developing atomic force microscopy-based nanoelectrical probes. Charges trapped at defects at the CdS/CdTe interface were probed by Kelvin probe force microscopy (KPFM) potential mapping and by ion-milling the CdTe superstrate device in a bevel glancing angle of ~0.5 degrees. The results show randomly distributed donor-like defects at the interface. The effect of K post-deposition treatment on the near-surface region of the CIGS film was studied by KPFM potential and scanning spreading resistance microscopy (SSRM) resistivity mapping, which shows passivation of grain-boundary potential and improvement of resistivity uniformity by the K treatment.

14 SOLAR ENERGY↗

Zirconium oxide surface passivation of crystalline silicon

This letter reports effective passivation of crystalline silicon (c-Si) surfaces by thermal atomic layer deposited zirconium oxide (ZrO x ). The optimum layer thickness and activation annealing conditions are determined to be 20 nm and 300 °C for 20 min. Cross-sectional transmission electron microscopy imaging shows an approximately 1.6 nm thick SiO x interfacial layer underneath an 18 nm ZrO x layer, consistent with ellipsometry measurements (~20 nm). Capacitance-voltage measurements show that the annealed ZrO x film features a low interface defect density of 1.0 × 10 11 cm -2 eV -1 and a low negative film charge density of -6 × 10 10 cm -2 . Effective lifetimes of 673 μs and 1.1 ms are achieved on p-type and n-type 1 Ω cm undiffused c-Si wafers, respectively, corresponding to an implied open circuit voltage above 720 mV in both cases. The results demonstrate that surface passivation quality provided by ALD ZrO x is consistent with the requirements of high efficiency silicon solar cells.

36 MATERIALS SCIENCE↗

Lifetime Enhancement of Visible Light Induced Photocharges in Tungsten and Nitrogen in situ Codoped TiO 2 :WN Thin Films

We report on one-step in situ codoped TiO2 thin films synthesized by cosputtering. The purpose of this acceptor-donor passivated codoping approach is to overcome the optoelectronic limitations that arise for monodoped TiO2 in photocatalytic applications. To evaluate these added benefits, the TiO2:WN thin films were characterized by different techniques. X-ray diffraction patterns and X-ray photoelectron spectral analysis revealed that both N and W dopants are mostly present in the desired substitutional locations. Additionally, the codoping approach was found to reduce the internal strain and defect density of the TiO2:WN films as compared to their monodoped TiO2:N counterparts. This defect reduction is confirmed via photocharge lifetime variation obtained using visible light flash photolysis time-resolved microwave conductivity measurements (FP-TRMC). Photocharge lifetime analysis indicated the presence of three distinct decay processes: charge trapping, recombination, and surface reactions. These characteristic lifetimes of the codoped TiO2:WN films (i.e., 0.08, 0.75, and 11.5 us, respectively) were found to be about double those of their nitrogen monodoped TiO2:N counterparts (i.e., 0.03, 0.35, and 6.8 us), quantitatively confirming the effective passivating outcome of the tungsten-nitrogen codoping approach developed here. The practicality of this method was confirmed by integrating the TiO2:WN films as photoanodes for the electro-photocatalytic, solar light driven degradation of a real pollutant (i.e., atrazine). A significant increase in the degradation kinetics, leading to a 4-fold increase in the pseudo-first-order degradation constant for the optimally doped TiO2:WN photoanodes (0.106 min-1) from the undoped TiO2-x ones (0.026 min-1), is a direct consequence of the increased photocharge lifetimes in tandem with visible light photosensitivity.

14 SOLAR ENERGY↗

Corrosion Behavior of 316L Stainless Steel Fabricated by Selective Laser Melting Under Different Scanning Speeds

This work discussed the effects of different scanning speeds (800, 1083, 1200 and 1400 mm/s) on the microstructure of 316L stainless steel manufactured by selective laser melting (SLM) and the related corrosion behavior. Results showed that there were more voids with faster scanning speeds, and there were oxide powder and non-melt silicon inside the defects. The SLM 316L exhibited a full gamma austenite phase filled with sub-grains, and the average grain size of SLM-1083 mm/s 316L was approximately 42 μm, three times larger than that of the quenched 316L. The pitting potentials for the SLM 316L were all approximately 300 mV higher than that of the quenched due to the modification of inclusions in SLM, but the corrosion rate for the SLM 316L was faster, which was attributed to the voids and unstable passive film. The number of pitting sites increased with the scanning speed, and the pits occurred preferentially at the voids in SLM 316L.

36 MATERIALS SCIENCE↗