SEARCH · Engineering Papers

Results for “data conditioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

All sources NASA NTRS DOE OSTI

NASA NTRS1956

Tensile properties of AZ11A-0 magnesium-alloy sheet under rapid-heating and constant temperature

Specimens of AZ31A-0 magnesium alloy sheet were heated to rupture at nominal rates of 0.2 F to 100 F per second under constant tensile load conditions. The data are presented and compared with the results of conventional tensile stress-strain tests at elevated temperatures after 1.2-hour exposure. A temperature-rate parameter was used to construct master curves from which stresses and temperatures for yield and rupture can be predicted under rapid-heating conditions. A comparison of the elevated-temperature tensile properties of AZ31A-0 and HK31XA-H24 magnesium-alloy sheet under both constant-temperature and rapid-heating conditions is included.

MATERIALS, PROPERTIES - THERMAL↗

NASA NTRS1977

Mars and earth - Origin and abundance of volatiles

An investigation is conducted concerning the factors which are responsible for the tenuous nature of the Martian atmosphere in comparison to the terrestrial atmosphere, taking into account new data obtained in connection with the Viking missions. It is found that Mars was poor in volatiles from the start and fell further behind earth by less complete outgassing, by extensive retrapping, and by the partial loss of lighter gases. Attention is given to noble gases on earth and Mars, the condensation of noble gases and other volatiles, the sources of earth's volatiles, the bulk composition of earth, the release of volatiles from earth, clues to the volatile endowment of Mars, an abundance table for Mars, a comparison of terrestrial and Martian conditions, isotopic data on noble gases, xenon-129 on Mars and earth, possibilities concerning the loss of an early Martian atmosphere, the evolution of the atmosphere of Mars, conditions in the case of planet Venus, and the reasons for the poorness of small planets in volatiles.

Anders, E.↗

NASA NTRS1945

Summary of Airfoil Data

The historical development of NACA airfoils is briefly reviewed. New data are presented that permit the rapid calculation of the approximate pressure distributions for the older NACA four-digit and five-digit airfoils by the same methods used for the NACA 6-series airfoils. The general methods used to derive the basic thickness forms for NACA 6 and 7-series airfoils together with their corresponding pressure distributions are presented. Detail data necessary for the application of the airfoils to wing design are presented in supplementary figures placed at the end of the paper. The report includes an analysis of the lift, drag, pitching-moment, and critical-speed characteristics of the airfoils, together with a discussion of the effects of surface conditions. Available data on high-lift devices are presented. Problems associated with lateral-control devices, leading-edge air intakes, and interference are briefly discussed, together with aerodynamic problems of application. (author)

Abbott, Ira H↗

NASA NTRSDate not supplied

Validation of Computational Fluid Dynamics Model for Pressurized Expulsion of Liquid Methane using Non-Condensable Pressurant

An important aspect of cryogenic fluid management is the design of the pressurization systems used to maintain and regulate the tank pressure as propellant is expelled from the tanks. To design these systems efficiently and effectively it is important to be able to predict the amount pressurant gas needed and how the pressurant gas affects the propellant as it is added in the tank. Computational fluid dynamics (CFD) modeling is a common tool that is used to help with these predictions, so it is crucial to have CFD models that are validated by comparing numerical results to experimental data. In the 1970’s extensive testing was done at NASA Plum Brook K-Site Facility exploring the pressurant gas requirements needed to maintain tank pressure while liquid methane is discharged from a spherical tank. These tests explored using different pressurant gases (methane, helium, hydrogen, and nitrogen) under static and sloshing conditions. The data gathered from the experiments includes the gas and wall temperatures at the end of the expulsion, the gas concentrations, and the total amount of pressurant added. This study presents a CFD model that accurately predicts similar results to the experimental data specifically for the tests in which helium, a non-condensable gas, was used. This comparison anchors the commercial CFD code Flow3D model and gives confidence for future use in design and analysis of pressurization systems for cryogenic propellant tanks

computational fluid dynamics↗

NASA NTRS1996

Automation of Command and Data Entry in a Glovebox Work Volume: An Evaluation of Data Entry Devices

The present study was designed to examine the human-computer interface for data entry while performing experimental procedures within a glovebox work volume in order to make a recommendation to the Space Station Biological Research Project for a data entry system to be used within the Life Sciences Glovebox. Test subjects entered data using either a manual keypad, similar to a standard computer numerical keypad located within the glovebox work volume, or a voice input system using a speech recognition program with a microphone headset. Numerical input and commands were programmed in an identical manner between the two systems. With both electronic systems, a small trackball was available within the work volume for cursor control. Data, such as sample vial identification numbers, sample tissue weights, and health check parameters of the specimen, were entered directly into procedures that were electronically displayed on a video monitor within the glovebox. A pen and paper system with a 'flip-chart' format for procedure display, similar to that currently in use on the Space Shuttle, was used as a baseline data entry condition. Procedures were performed by a single operator; eight test subjects were used in the study. The electronic systems were tested under both a 'nominal' or 'anomalous' condition. The anomalous condition was introduced into the experimental procedure to increase the probability of finding limitations or problems with human interactions with the electronic systems. Each subject performed five test runs during a test day: two procedures each with voice and keypad, one with and one without anomalies, and one pen and paper procedure. The data collected were both quantitative (times, errors) and qualitative (subjective ratings of the subjects).

Steele, Marianne K.↗

NASA NTRS2000

Measurement and Modeling of Steep Ocean Wave Slopes

Our study emphasizes the importance of identifying and quantifying the distribution variance, skewness and kurtosis from optical and microwave scattering observations. Recent field measurements of the sea slope distribution for intermediate-to-long scale gravity waves will be presented. These data were collected using an airborne laser range system designed to estimate the surface slope vector at horizontal scales of 1-2 m. The observed slope distribution tail indicates that the occurrence of steep waves substantially exceeds a Gaussian prediction. This measured peakedness is present over the wide range of sea state and wind speed conditions encountered. Data are further evaluated within the context of Cox and Munk's well-known sea slope investigations. Based on a re-evaluation of the Cox and Munk's reported parameters, we find a consistent picture develops wherein data are shown to consistently indicate non-Gaussian statistics. One fundamental application of such a non-Gaussian slope observation is its place in modifying predicted wave breaking probability to help to better quantify gas transfer processes at the sea surface.

Chapron, B.↗

NASA NTRS1974

Correlation of coastal water turbidity and current circulation with ERTS-1 and Skylab imagery

The article reviews investigations of current circulation patterns, suspended sediment concentration, coastal frontal systems, and waste disposal plumes based on visual interpretation and digital analysis of ERTS-1 and Skylab/EREP imagery. Data on conditions in the Delaware Bay area were obtained from 10 ERTS-1 passes and one Skylab pass, with simultaneous surface and airborne sensing. The current patterns and sediments observed by ERTS-1 correlated well with ground-based observations. Methods are suggested which would make it possible to identify certain pollutants and sediment types from multispectral scanner data.

Klemas, V.↗

NASA NTRS1978

Large Area Crop Inventory Experiment (LACIE). Feasibility of assessing crop condition and yield from LANDSAT data

The author has identified the following significant results. Yield modelling for crop production estimation derived a means of predicting the within-a-year yield and the year-to-year variability of yield over some fixed or randomly located unit of area. Preliminary studies indicated that the requirements for interpreting LANDSAT data for yield may be sufficiently similar to those of signature extension that it is feasible to investigate the automated estimation of production. The concept of an advanced yield model consisting of both spectral and meteorological components was endorsed. Rationale for using meteorological parameters originated from known between season and near harvest dynamics in crop environmental-condition-yield relationships.

Source record↗

NASA NTRS1994

Using LabVIEW for Telemetry Monitoring and Display

Part of the Jet Propulsion Laboratory's (JPL's) Instrumentation Section, the Measurement Technology Center (MTC) evaluates data acquisition hardware and software products for inclusion into the Instrument Loan Pool, which are the made available to JPL experimenters.

off-the-shelf products turn-key measurement system↗

NASA NTRS1973

Study of exothermic processes in shock ignited gases by the use of laser shear interferometry.

The paper reports on the measurements of maximum exothermic power pulses attainable from a given chemical system. Experimental tests involved the use of a shock tube technique whereby the exothermic process of combustion was controlled by reflected shock so that it occurred under virtually inviscid flow conditions, the data having been obtained at a resolution commensurate with the actual rate of chemical reaction. Experimental observations were made by means of a novel method of laser shear interferometry. Chemical systems treated in this manner comprised of mixtures of stoichiometric hydrogen-oxygen with 80 and 90% argon, while the measurements covered the full permissible range of initial thermodynamic conditions.

Meyer, J. W.↗

NASA NTRS1975

Experimental transient turbine blade temperatures in a research engine for gas stream temperatures cycling between 1067 and 1567 k

Experimental transient turbine blade temperatures were obtained from tests conducted on air-cooled blades in a research turbojet engine, cycling between cruise and idle conditions. Transient data were recorded by a high speed data acquisition system. Temperatures at the same phase of each transient cycle were repeatable between cycles to within 3.9 K (7 F). Turbine inlet pressures were repeatable between cycles to within 0.32 N/sq cm (0.47 psia). The tests were conducted at a gas stream temperature of 1567 K (2360 F) at cruise, and 1067 K (1460 F) at idle conditions. The corresponding gas stream pressures were about 26.2 and 22.4 N/sq cm (38 and 32.5 psia) respectively. The nominal coolant inlet temperature was about 811 K (1000 F).

Gauntner, D. J.↗

NASA NTRS1994

Analysis of selected materials flown on interior locations of the Long Duration Exposure Facility

This report documents the post-flight condition of selected hardware taken from interior locations on the Long Duration Exposure Facility (LDEF). This hardware was generally in excellent condition. Outgassing data is presented for heat shrink tubing and fiberglass composite shims. Variation in total mass loss (TML) values for heat shrink tubing were correlated with location. Nylon grommets were evaluated for mechanical integrity; slight embrittlement was observed for flight specimens. Multi-layer insulation blankets, wire bundles, and paints in non-exposed interior locations were all in visibly good condition. Silicon-containing contaminant films were observed on silver-coated hex nuts at the space- and Earth-end interior locations.

Smith, H. A.↗

NASA NTRS2004

Laboratory Infrared Spectra of Polycyclic Aromatic Nitrogen Heterocycles: Quinoline, and Phenanthridine in Solid Argon and H2O

Polycyclic aromatic hydrocarbons (PAHs) are common throughout the universe. Their detection and identification are based on telescopic infrared (IR) spectra compared with laboratory data. Polycyclic Aromatic Nitrogen Heterocycles (PANHs) are heterocyclic aromatics i.e., PAHs with carbon atoms replaced by a nitrogen atom. These molecules should be present in the interstellar medium, but have received relatively little attention. We present mid-IR spectra of two PANHs, quinoline (C9H7N), and phenanthridine (C13H9N) isolated in solid argon and frozen in solid H2O at 12 K, conditions yielding data directly comparable to astronomical observations. In contrast to simple PAHs, that do not interact strongly with solid H2O, the nitrogen atoms in PANHs are potentially capable of hydrogen bonding with H2O. Whereas the IR spectrum of phenanthridine in H2O is similar to that of the same compound isolated in an argon matrix, quinoline absorptions shift up to 16 cm(sup -1) (0.072 mm) between argon and H2O. Thus, astronomers will not always be able to rely on IR band positions of matrix isolated PANHs to correctly interpret the absorptions of PANHs frozen in H2O ice grains. Furthermore, our data suggest that relative band areas also vary, so determining column densities to better than a factor of 3 will require knowledge of the matrix in which the PANH is embedded and laboratory studies of relevant samples.

Bernstein, M. P.↗

NASA NTRS1977

Load distribution on a close-coupled wing canard at transonic speeds

This paper reports on a wind-tunnel test where load distributions were obtained at transonic speeds on both the canard and wing surfaces of a closely-coupled wing-canard configuration. The investigation included detailed component and configuration arrangement studies to provide insight into the various aerodynamic interference effects for the leading-edge vortex flow conditions encountered. Data indicate that increasing the Mach number from 0.70 to 0.95 caused the wing leading-edge vortex to burst over the wing when the wing was in the presence of the high canard. For some of the outboard span locations, the leading-edge vortex reattachment streamline intersects the wing trailing edge inboard of these span locations, thus, the Kutta condition was not satisfied. In general, the effect of adding a canard was to reduce the lift inboard and somewhat increase the lift outboard similar to the trends that would have been expected had the flow been attached.

Gloss, B. B.↗

NASA NTRSDate not supplied

Thermal Vacuum Testing Strategy and Thermal Desktop Model Correlation for the Moon to Mars Planetary Autonomous Construction Technologies (MMPACT) Robotic Terrestrial Arm

This paper discusses the initial thermal vacuum testing of the MMPACT robotic terrestrial arm. The robotic arm is part of a construction system designed for the lunar south pole surface. The first thermal vacuum test was a risk mitigation test to ensure the arm could operate in vacuum, with all other data collection as secondary priorities. 44 thermocouples (TCs) were attached to the arm. Installation was done with additional care to account for both the extra wiring harness weight on the arm with the TC wires and increased focus on stabilizing the TC attachments to the moving components. Thermal steady state of <= 0.01°C/hour was reached for the hot set of testing conditions. This data was used to correlate the Thermal Desktop (TD) model to the test results within +/- 5°C.

Thermal analysis↗

NASA NTRSDate not supplied

Thermal Vacuum Testing Strategy and Thermal Desktop Model Correlation for the Moon to Mars Planetary Autonomous Construction Technologies (MMPACT) Robotic Terrestrial Arm

Thermal analysis↗

DOE OSTI2026

Knowledge-guided graph machine learning for spatially distributed prediction of daily discharge and nitrogen export dynamics

Spatially distributed prediction of streamflow and nitrogen export dynamics is essential for precision management of agricultural watersheds. While temporal deep learning models such as Long Short-Term Memory (LSTM) have shown strong performance at basin scales, their ability to generalize spatially is limited by insufficient representation of spatial dependencies and flow paths, particularly under data-scarce conditions. To address this gap, we propose HydroGraphNet, a knowledge-guided graph machine learning framework that integrates process-based knowledge and explicit spatial learning into temporal modeling. This framework incorporates directed graph topology to encode watershed connectivity and upstream inflows, with mass balance constraints to improve physical consistency. To enhance generalization in sparsely monitored regions, HydroGraphNet is pretrained on synthetic data generated by the SWAT+ (Soil and Water Assessment Tool Plus) model. We evaluated HydroGraphNet in the Upper Sangamon River Basin (44 HUC-12 subwatersheds, 2001–2020) against two LSTM baselines: a lumped basin-level model and a distributed variant. When benchmarked on SWAT+ simulations in pretraining, HydroGraphNet improved test NSEs by 8.9% (discharge) and 13.7% (NO₃–N load) in temporal extrapolation, and by 27.1% and 34.7% in spatial extrapolation, relative to the Lumped LSTM baseline. After fine-tuning with USGS monitoring data, the model achieved mean test NSE (KGE) scores of 0.768 (0.861) for discharge and 0.626 (0.664) for NO₃–N load, substantially outperforming baselines. Attribution analysis further highlighted the importance of upstream inflow representation and graph-based spatial learning in capturing cross-subwatershed dependencies. The model also reproduced seasonal hydrological and biogeochemical patterns consistent with known processes, demonstrating its robustness and process fidelity for spatially distributed prediction. Altogether, HydroGraphNet advances the integration of physical knowledge and spatially explicit learning in hydrological modeling, offering a generalizable framework for distributed modeling to support spatially targeted water quality management in data-scarce watersheds.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1998

Technical Report Series on Global Modeling and Data Assimilation: A Comparison of GEOS Assimilated Data with FIFE Observations - Volume 14

First ISLSCP Field Experiment (FIFE) observations have been used to validate the near-surface proper- ties of various versions of the Goddard Earth Observing System (GEOS) Data Assimilation System. The site- averaged FIFE data set extends from May 1987 through November 1989, allowing the investigation of several time scales, including the annual cycle, daily means and diurnal cycles. Furthermore, the development of the daytime convective planetary boundary layer is presented for several days. Monthly variations of the surface energy budget during the summer of 1988 demonstrate the affect of the prescribed surface soil wetness boundary conditions. GEOS data comes from the first frozen version of the assimilation system (GEOS-1 DAS) and two experimental versions of GEOS (v. 2.0 and 2.1) with substantially greater vertical resolution and other changes that influence the boundary layer. This report provides a baseline for future versions of the GEOS data assimilation system that will incorporate a state-of-the-art land surface parameterization. Several suggestions are proposed to improve the generality of future comparisons. These include the use of more diverse field experiment observations and an estimate of gridpoint heterogeneity from the new land surface parameterization.

Bosilovich, Michael G.↗