Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “control layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

The design and preliminary calibration of a boundary-layer flow channel

Design procedures for a new low-speed boundary-layer research channel are described. The channel is an open-circuit wind tunnel for the study of two-dimensional boundary layers under controlled pressure gradients, and follows design guidelines from published literature on blower tunnels with wide-angle diffusers. The contraction was arranged in a modular fashion permitting two different test sections of square and high-aspect-ratio cross section. A radical type of wide-angle diffuser was employed, and a stream-tube computer code (GE Streamtube Curvature Code) was used to check the contraction designs. The alternate test sections have the following specifications: 2- by 2-foot cross section with a fixed velocity of 23 ft/sec, and a boundary-layer section with a 0.5- by 2-foot cross section at a fixed velocity of approximately 89 ft/sec. Experimental techniques and data are described for the evaluation of diffuser effectiveness, boundary-layer channel characteristics, and overall performance of the facility.

Rao, Dhanvada M.↗
NASA NTRS1989

Low dimensional models of the wall region of a turbulent boundary layer, and the possibility of control

A method of identification of coherent structures in a random turbulent flow is outlined with emphasis on the structure best correlated with a random energy-integrable field and application of the proper orthogonal decomposition to the shear flow of the wall region. The wall region of a pipe flow with almost pure glycerine is investigated experimentally, dynamic equations are obtained, and an energy-transfer model is employed. Numerical solutions are obtained, implications for the flow in the wall region are discussed with focus placed on the sets of solutions exhibiting intermittency. The most significant finding of the study is considered to be the suggestion of the etiology of the bursting phenomenon; presuming that abrupt transitions from one fixed point to the other can be identified with a burst, these bursts appear to be produced autonomously by the wall region, but be triggered by pressure signals from the outer layer.

Lumley, John L.↗
NASA NTRS1995

Active control of panel vibrations induced by a boundary layer flow

The problems of active and passive control of sound and vibration has been investigated by many researchers for a number of years. However, few of the articles are concerned with the sound and vibration with flow-structure interaction. Experimental and numerical studies on the coupling between panel vibration and acoustic radiation due to flow excitation have been done by Maestrello and his associates at NASA/Langley Research Center. Since the coupled system of nonlinear partial differential equations is formidable, an analytical solution to the full problem seems impossible. For this reason, we have to simplify the problem to that of the nonlinear panel vibration induced by a uniform flow or a boundary-layer flow with a given wall pressure distribution. Based on this simplified model, we have been able to consider the control and stabilization of the nonlinear panel vibration, which have not been treated satisfactorily by other authors. Although the sound radiation has not been included, the vibration suppression will clearly reduce the sound radiation power from the panel. The major research findings are presented in three sections. In section two we describe results on the boundary control of nonlinear panel vibration, with or without flow excitation. Sections three and four are concerned with some analytical and numerical results in the optimal control of the linear and nonlinear panel vibrations, respectively, excited by the flow pressure fluctuations. Finally, in section five, we draw some conclusions from research findings.

Chow, Pao-Liu↗
NASA NTRS1998

Active Control of Panel Vibrations Induced by a Boundary Layer Flow

In recent years, active and passive control of sound and vibration in aeroelastic structures have received a great deal of attention due to many potential applications to aerospace and other industries. There exists a great deal of research work done in this area. Recent advances in the control of sound and vibration can be found in the several conference proceedings. In this report we will summarize our research findings supported by the NASA grant NAG-1-1175. The problems of active and passive control of sound and vibration has been investigated by many researchers for a number of years. However, few of the articles are concerned with the sound and vibration with flow-structure interaction. Experimental and numerical studies on the coupling between panel vibration and acoustic radiation due to flow excitation have been done by Maestrello and his associates at NASA/Langley Research Center. Since the coupled system of nonlinear partial differential equations is formidable, an analytical solution to the full problem seems impossible. For this reason, we have to simplify the problem to that of the nonlinear panel vibration induced by a uniform flow or a boundary-layer flow with a given wall pressure distribution. Based on this simplified model, we have been able to study the control and stabilization of the nonlinear panel vibration, which have not been treated satisfactorily by other authors. The vibration suppression will clearly reduce the sound radiation power from the panel. The major research findings will be presented in the next three sections. In Section II we shall describe our results on the boundary control of nonlinear panel vibration, with or without flow excitation. Section III is concerned with active control of the vibration and sound radiation from a nonlinear elastic panel. A detailed description of our work on the parametric vibrational control of nonlinear elastic panel will be presented in Section IV. This paper will be submitted to the Journal of Acoustic Society of America for publication.

Chow, Pao-Liu↗
NASA NTRS1987

Boundary-layer and wake measurements on a swept, circulation-control wing

Wind tunnel measurements of boundary layer and wake velocity profiles and surface static pressure distributions are presented for a swept, circulation control wing. The model is an aspect ratio four semispan wing mounted on the tunnel side wall as a sweep angle of 45 deg. A full span, tangetial, rearward blowing, circulation control slot is located ahead of the trailing edge on the upper surface. Flow surveys were obtained at mid-semispan at freestream Mach numbers of 0.425 and 0.70. Boundary layer profiles measured on the forward portions of the wing are approximately streamwise and two dimensional. The flow in the vicinity of the jet exit and in the near wake is highly three dimensional. The jet flow near the slot on the Coanda surface is directed normal to the slot. Near wake surveys show large outboard flows at the center of the wake. At Mach 0.425 and a 5 deg angle of attack, a range of jet blowing rates was found for which an abrupt transition from incipient separation to attached flow occurs in the boundary layer upstream of the slot. The variation in the lower surface separation location with blowing rate was determined from the boundary layer measurements at Mach 0.425.

Spaid, Frank W.↗
NASA NTRS1995

A self-contained, automated methodology for optimal flow control validated for transition delay

This paper describes a self-contained, automated methodology for flow control along with a validation of the methodology for the problem of boundary layer instability suppression. The objective of control is to match the stress vector along a portion of the boundary to a given vector; instability suppression is achieved by choosing the given vector to be that of a steady base flow, e.g., Blasius boundary layer. Control is effected through the injection or suction of fluid through a single orifice on the boundary. The present approach couples the time-dependent Navier-Stokes system with an adjoint Navier-Stokes system and optimality conditions from which optimal states, i.e., unsteady flow fields, and control, e.g., actuators, may be determined. The results demonstrate that instability suppression can be achieved without any a priori knowledge of the disturbance, which is significant because other control techniques have required some knowledge of the flow unsteadiness such as frequencies, instability type, etc.

Joslin, Ronald D.↗
NASA NTRS1975

Metal-thin film insulator-semiconductor solar cells

The characteristics of a specific M-I-S structure are analyzed for various assumed roles of the thin-film insulating layer. It is shown that the behavior of an ideal Schottky barrier is obtained in the case where the insulating layer does not hinder transport and no localized states are present (or, if present, their population is dictated by the metal Fermi level). The cell is a majority carrier device; by using the insulating layer to control transport, it becomes a minority carrier cell.

Fonash, S. J.↗
NASA NTRS1978

Design of a laminar-flow-control supercritical airfoil for a swept wing

An airfoil was analytically designed and analyzed for a combination of supercritical flow and laminar flow control (LFC) by boundary layer suction. A shockless inverse method was used to design an airfoil and an analysis method was used in lower surface redesign work. The laminar flow pressure distributions were computed without a boundary layer under the assumption that the laminar boundary layer would be kept thin by suction. Inviscid calculations showed that this 13.5 percent thick airfoil has shockless flows for conditions at and below the design normal Mach number of 0.73 and the design section lift coefficient of 0.60, and that the maximum local normal Mach number is 1.12 at the design point. The laminar boundary layer instabilities can be controlled with suction but the undercut leading edge of the airfoil provides a low velocity, constant pressure coefficients region which is conducive to laminar flow without suction. The airfoil was designed to be capable of lift recovery with no suction by the deflection of a small trailing edge flap.

Allison, D. O.↗
NASA NTRS1980

Predicting propulsion system drag

DONBOL computer program analytically predicts axisymmetric nozzle afterbody pressure distributions and drag. Predictions are based on Neumann solution for inviscid external flow coupled with modified Reshotko-Tucker integral boundary layer technique, control volume method of Presz for calculating flow in separated region, and inviscid one dimensional solution for jet exhaust flow. Comparisons with experimental data indicate program accurately predicts pressure distributions of boattail afterbodies for which jet exhaust plume can be simulated by solid body. For other configurations, nozzle pressure drag seems to be significantly underpredicted. Method is limited to subsonic free stream mach numbers below those for which flow over body becomes sonic.

Putnam, L. E.↗
NASA NTRS1981

Physics of planetary atmospheres and ionospheres

The traditional atmospheric regions, the distinction between homosphere and heterosphere, and changing atmospheric composition are discussed. The validity of the barometric law based on a Maxwell-Boltzmann distribution, for the major part of a planetary atmosphere and its breakdown in the exosphere due to escape of atmospheric particles is considered. The formation and maintenance of photochemical and diffusion-controlled ionospheric layers are treated. Their applicability to planetary ionospheres is dealt with. The spatial extent of magnetic and nonmagnetic planet ionospheres is investigated. Thermal and nonthermal processes responsible for the mass loss of planetary atmospheres are surveyed.

Bauer, S. J.↗
NASA NTRS1984

Computation of Bragg Reflection for Layered Microstructures

Bragg diffractors analyzed for use in X-ray mirrors and other applications. SLM tailored to specific applications by varying layer thicknesses and number of layers to control reflectivity diffraction width, and wavelength resolution. Applications as glancing incidence mirrors or filters for wavelengths of few to few hundred angstroms.

Underwood, J. W.↗
NASA NTRS1987

Space telerobotics technology demonstration program

The paper reports the ongoing development of a telerobot demonstrator. The demonstrator is implemented as a laboratory-based research testbed, and will show proof-of-concept for supervised automation of space assembly, servicing, and repair operations. The demonstrator system features a hierarchically layered intelligent control architecture which enables automated planning and run-time sequencing of complex tasks by a supervisory human operator. The demonstrator also provides a full bilateral force-reflecting hand control teleroperations capability. The operator may switch smoothly between the automated and teleroperated tasking modes in run-time, either on a preplanned or operator-designated basis.

Szirmay, S. Z.↗