Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “contact interaction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Cometary plasma boundaries

The solar wind starts to interact with comets at distances from the nucleus of several million kilometers. The nature of the interaction changes as a function of cometocentric distance. Several dynamically important boundaries have been observed in the cometary plasma environment by instruments on several spacecraft: (1) the bow shock marks the transition from supersonic to subsonic solar wind flow, (2) the cometopause was observed at a distance of about 100,000 km from Comet Halley where the flow begins to stagnate and where charge exchange with neutrals becomes important, (3) the diamagnetic cavity boundary (i.e., contact surface, ionopause) separates magnetized and unmagnetized cometary plasma, (4) the magnetotail boundary defines the tail lobes, (5) the plasma sheet boundary defines the extent of the plasma sheet, and (6) the density enhancement layer was observed at a distance of 10,000 km from Comet Halley and might be located where the neutrals and plasma thermally decouple.

Cravens, T. E.↗

Osiris-Rex Post-Tag Observation Trajectory Design and Navigation Performance

NASA’s OSIRIS-REx spacecraft successfully collected a sample of asteroid regolith from the surface of near-Earth asteroid Bennu in October of 2020. Subsequent imaging of the sampler head showed material leaking from the collection mechanism, thus stowage of the sample precluded execution of any planned maneuvers in the following days. Optical navigation imaging also ceased in the days following sample collection. The desire to image the sample site to investigate the results of the spacecraft-to-surface interaction led to the Navigation team designing a trajectory to return to Bennu after several months in order to image the surface one final time. After several iterations a trajectory design was created that satisfied the numerous constraints that were levied in order to place utmost importance on the safety of the spacecraft and stowed sample, while also closely emulating previously obtained imaging conditions to provide a close comparison of site pre- and post-contact. Significant analysis was necessary in order to reliably reacquire the asteroid after several months without optical navigation imagery. The final design required five maneuvers to return the spacecraft to Bennu and perform a final flyby of the asteroid at a distance of 3.8 kilometers. Successful execution of the phase provided key insights regarding the performance of the sample collection activities and the subsurface composition of the asteroid.

Daniel R Wibben↗

Trace Element Abundances Measured in Concentric and Texturally Distinct Fine-Grained Rims Surrounding Allende Chondrules

Layered rims of dust-sized material surround some chondrules and other early formed nebular particles, such as calcium aluminum inclusions in chondritic meteorites. In the Allende meteorite most chondrules(~85%) are un-rimmed and in direct contact with the host matrix material [1]. When present, rim thickness appears correlated to underlying particle size in both the Allende and Murchison chondrites [1,2]. This diverse behavior strongly argues for pre-parent body formation of rimmed particles as they traversed distinct (cooler and/or dustier) nebular environments [1]. Nebular rim formation involves accretion of unequilibrated dust to chondrule surfaces, recording evidence for the formation of at least two separate particle populations (chondrules and dust) that interacted in the nebula, and therefore potentially record distinct nebular reservoirs (e.g. [3-5]). Additionally, some particles exhibit textural evidence for multiple rim layers, (e.g., [1], further investigated herein). Herein, we evaluate the chemistry of concentrically and texturally distinct chondrule rim layers to investigate the possibility of discrete rim formation events recorded by individual chondrules (Fig. 1A,B). Using laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS) we measure major, minor, and trace elements of the rims and particles in Allende. Samples were characterized in detail previously by electron microanalysis for their mineralogy, textures, particle size, and rim thickness(es) [1].

Chondrites↗

An integrated dexterous robotic testbed for space applications

An integrated dexterous robotic system was developed as a testbed to evaluate various robotics technologies for advanced space applications. The system configuration consisted of a Utah/MIT Dexterous Hand, a PUMA 562 arm, a stereo vision system, and a multiprocessing computer control system. In addition to these major subsystems, a proximity sensing system was integrated with the Utah/MIT Hand to provide capability for non-contact sensing of a nearby object. A high-speed fiber-optic link was used to transmit digitized proximity sensor signals back to the multiprocessing control system. The hardware system was designed to satisfy the requirements for both teleoperated and autonomous operations. The software system was designed to exploit parallel processing capability, pursue functional modularity, incorporate artificial intelligence for robot control, allow high-level symbolic robot commands, maximize reusable code, minimize compilation requirements, and provide an interactive application development and debugging environment for the end users. An overview is presented of the system hardware and software configurations, and implementation is discussed of subsystem functions.

Li, Larry C.↗

Nanotube/Quantum Dot-Polymer Solar Cells

Single wall carbon nanotubes used or this study were synthesized using the pulse laser vaporization technique. The as-produced SWNTs were collected from the condensed region on the quartz tube outside the furnace and purified by modification of the previously reported procedure. Preparation of the SWNT-P3OT composite solutions was performed using a series of mixing and sonication steps as previously demonstrated for other SWNT-polymer systems. Device fabrication involved the use of commercially-obtained, high quality (i.e., less than 10 W/sq.) ITO-coated polyethylene terapthalate (PET) substrates. Initially, an intrinsic layer of pristine P3OT is spray deposited (approx. 1-2 mL of the 15 mg/mL solution) onto the masked, 1 sq in. active area of the substrate. This is followed with spray deposition of the SWNT-P3OT composite solutions at similar volumes. As seen completion of the solar cell occurs when aluminum contacts (typical thicknesses of l000A) are applied to the IT0 and SWNT-P3OT composite film layers. The homogeneous distribution of SWNTs in a polymer matrix is dependent upon the ability of the polymer chain to associate with the SWNT superstructure. Stable composite dispersions of 0.1 % and 1.0% w/w SWNTs in P3OT were produced and analyzed in this study. Optical spectroscopy was conducted to observe the SWNT doping level effects on the absorption properties and infer potential electronic interactions between dopant and polymer. Shown is an overlay of these spectra where the pristine P3OT shows strong optical absorption at energies less than 2 eV. As expected, variation in absorption properties for the SWNT-P3OT composites is observed as the doping level increases. Through modification of the SWNT doping level in the polymer, it is possible to alter the absorption pattern of these composite materials. In fact, at these relatively low doping levels, the P3OT shows a significant enhancement in absorption through the near-IR and visible regions. The gray curve for purified SWNTs is offset from the other three for clarity, but indicates the typical complex pattern observed for this spectral range.

Bailey, Sheila G.↗

Interacting Surfaces and Atmospheres in the Outer Solar System

The work reported here is an extension of ongoing efforts in data reduction and modeling of the spectral reflectances of several objects in the outer Solar System. In general terms, this requires an evaluation of the data obtained at the telescope, conversion of those data into geometric albedo units, and the combination of individual spectrum segments into a complete spectrum over the wavelength interval of interest. The modeling effort to produce a synthetic spectrum of a given Solar System object requires the complex refractive indices (the optical constants) of candidate surface materials, including ices, minerals, and organic solids. Those indices are primarily available only through contacts with other researchers, including colleagues at NASA Ames and at other institutions. Once obtained, the indices must be convolved with the telescopic data and then used in a computational model to produce the required synthetic spectrum for comparison with the data obtained at the telescope. In this way, we reach a convergence on the chemical composition and microstructural properties of the surfaces of objects in the outer Solar System.

DalleOre, Cristina↗

Isolation of Resistance-Bearing Microorganisms

To better exploit the principles of gas transport and mass transport during the processes of cell seeding of 3D scaffolds and in vitro culture of 3D tissue engineered constructs, the oscillatory cell culture bioreactor provides a flow of cell suspensions and culture media directly through a porous 3D scaffold (during cell seeding) and a 3D construct (during subsequent cultivation) within a highly gas-permeable closed-loop tube. This design is simple, modular, and flexible, and its component parts are easy to assemble and operate, and are inexpensive. Chamber volume can be very low, but can be easily scaled up. This innovation is well suited to work with different biological specimens, particularly with cells having high oxygen requirements and/or shear sensitivity, and different scaffold structures and dimensions. The closed-loop changer is highly gas permeable to allow efficient gas exchange during the cell seeding/culturing process. A porous scaffold, which may be seeded with cells, is fixed by means of a scaffold holder to the chamber wall with scaffold/construct orientation with respect to the chamber determined by the geometry of the scaffold holder. A fluid, with/without biological specimens, is added to the chamber such that all, or most, of the air is displaced (i.e., with or without an enclosed air bubble). Motion is applied to the chamber within a controlled environment (e.g., oscillatory motion within a humidified 37 C incubator). Movement of the chamber induces relative motion of the scaffold/construct with respect to the fluid. In case the fluid is a cell suspension, cells will come into contact with the scaffold and eventually adhere to it. Alternatively, cells can be seeded on scaffolds by gel entrapment prior to bioreactor cultivation. Subsequently, the oscillatory cell culture bioreactor will provide efficient gas exchange (i.e., of oxygen and carbon dioxide, as required for viability of metabolically active cells) and controlled levels of fluid dynamic shear (i.e., as required for viability of shear-sensitive cells) to the developing engineered tissue construct. This bioreactor was recently utilized to show independent and interactive effects of a growth factor (IGF-I) and slow bidirectional perfusion on the survival, differentiation, and contractile performance of 3D tissue engineering cardiac constructs. The main application of this system is within the tissue engineering industry. The ideal final application is within the automated mass production of tissue- engineered constructs. Target industries could be both life sciences companies as well as bioreactor device producing companies.

Venkateswaran, Kasthuri, J.↗

Oscillating Cell Culture Bioreactor

To better exploit the principles of gas transport and mass transport during the processes of cell seeding of 3D scaffolds and in vitro culture of 3D tissue engineered constructs, the oscillatory cell culture bioreactor provides a flow of cell suspensions and culture media directly through a porous 3D scaffold (during cell seeding) and a 3D construct (during subsequent cultivation) within a highly gas-permeable closed-loop tube. This design is simple, modular, and flexible, and its component parts are easy to assemble and operate, and are inexpensive. Chamber volume can be very low, but can be easily scaled up. This innovation is well suited to work with different biological specimens, particularly with cells having high oxygen requirements and/or shear sensitivity, and different scaffold structures and dimensions. The closed-loop changer is highly gas permeable to allow efficient gas exchange during the cell seeding/culturing process. A porous scaffold, which may be seeded with cells, is fixed by means of a scaffold holder to the chamber wall with scaffold/construct orientation with respect to the chamber determined by the geometry of the scaffold holder. A fluid, with/without biological specimens, is added to the chamber such that all, or most, of the air is displaced (i.e., with or without an enclosed air bubble). Motion is applied to the chamber within a controlled environment (e.g., oscillatory motion within a humidified 37 C incubator). Movement of the chamber induces relative motion of the scaffold/construct with respect to the fluid. In case the fluid is a cell suspension, cells will come into contact with the scaffold and eventually adhere to it. Alternatively, cells can be seeded on scaffolds by gel entrapment prior to bioreactor cultivation. Subsequently, the oscillatory cell culture bioreactor will provide efficient gas exchange (i.e., of oxygen and carbon dioxide, as required for viability of metabolically active cells) and controlled levels of fluid dynamic shear (i.e., as required for viability of shear-sensitive cells) to the developing engineered tissue construct. This bioreactor was recently utilized to show independent and interactive effects of a growth factor (IGF-I) and slow bidirectional perfusion on the survival, differentiation, and contractile performance of 3D tissue engineering cardiac constructs. The main application of this system is within the tissue engineering industry. The ideal final application is within the automated mass production of tissue- engineered constructs. Target industries could be both life sciences companies as well as bioreactor device producing companies.

Freed, Lisa E.↗

Energetics of Reactions between Ceramic Coating Materials and their Binary Oxide Components with Silicate Melts

This paper summarizes our previous and current studies of using high-temperature calorimetry to investigate the energetics of reactions of ceramic coating materials (e.g., yttrium disilicate and 7-wt% yttria-stabilized zirconia) and their binary oxide components with silicate melts in the CaO–MgO–Al 2 O 3 –SiO 2 (CMAS) system. Such interactions are found to become stronger (more exothermic) with increasing difference in acid–base character between these materials and the melt. Our results suggest that the reactivity between the coating materials and the melt increases with decreasing thermodynamic stability (less exothermic enthalpy of formation from oxide components) of the coating material. They also suggest that ceramic coating materials made from binary oxides that have less exothermic enthalpies of solution and mixing are less susceptible to CMAS melt corrosion when in contact with an acidic, relatively polymerized, melt rich in SiO 2 . Thus, we propose that new coating material formulation and CMAS melt corrosion mitigation strategies should be optimized based on the energetic contributions of their binary oxide components.

CMAS↗

"Coulombic Viscosity" In Granular Materials: Planetary and Astrophysical Implications

The term "Coulombic viscosity" is introduced here to define an empirically observed phenomenon from experiments conducted in both microgravity, and in ground-based 1-g conditions. In the latter case, a sand attrition device was employed to test the longevity of aeolian materials by creating two intersecting grain-circulation paths or cells that would lead to most of the grain energy being expended on grain-to-grain collisions (simulating dune systems). In the areas in the device where gravitationally-driven grain-slurries recycled the sand, the slurries moved with a boundary-layer impeded motion down the chamber walls. Excessive electrostatic charging of the grains during these experiments was prevented by the use of an a.c. corona (created by a Tesla coil) through which the grains passed on every cycle. This created both positive and negative ions which neutralized the triboelectrically-generated grain charges. When the corona was switched on, the velocity of the wall-attached slurries increased by a factor of two as approximately determined by direct observation. What appeared to be a freely-flowing slurry of grains impeded only by intergranular mechanical friction, had obviously been significantly retarded in its motion by electrostatic forces between the grains; with the charging reduced, the grains were able to move past one another without a flow "viscosity" imposed by the Coulombic intergranular forces. A similar phenomenon was observed during microgravity experiments aboard Space Shuttle in USML-1 & USML-2 spacelabs where freely-suspended clouds of sand were being investigated for their potential to for-m aggregates. In this environment, the grains were also charged electrostatically (by natural processes prior to flight), but were free from the intervention of gravity in their interactions. The grains were dispersed into dense clouds by bursts of air turbulence and allowed to form aggregates as the ballistic and turbulent motions damped out. During this very brief (30-60 sec) damping period, motion of the grains was observed to be retarded by the electrostatic interactions. The fact that the grains almost instantly formed aggregates was evidence that their ballistic motions had been constrained and redirected by the dipole-dipole interactions that led to filamentary aggregate development. Undoubtedly, the "Coulombic viscosity" of the cloud assisted in damping grain motion so rapidly. The electrostatically-induced grain-cloud viscosity or drag exerted on grain motion, is a complex function of three major parameters: charge magnitude, charge sign, and mean intergranular distance. The above experiments illustrate one particular type of granular behavior. The discussion here will therefore be restricted to drag relationships: (a) between grains that are naturally charged triboelectrically and thus exhibit dipole-dipole attractions between one another even if there are slight net charges present (which can be overwhelmed by dipole coupling at short distances), and (b) between grains that are densely spaced where the intergranular distance varies between zero and some value (usually tens or hundreds of grain diameters) that permits each grain to detect the dipole moment of another grain -- the distance is not so great that other grains appears as neutral electrical "singularities. I. Aeolian transport: During motion of grains in a saltation cloud (on Earth, Mars, or Venus), triboelectric charging must occur as a result of multiple grain contacts, and by friction with the entraining air. A situation might develop that is similar to the one described above in the attrition device: grain motion becoming significantly retarded (reduced flux) as grains find it increasingly difficult to either separate from the surface, or to pass one another without Coulombic retarding forces. A "Coulombic drag" will exist at flux initiation and increase with time to work in direct opposition to the aerodynamic drag that drives the grain motion. It is predicted that this will lead to an increase with time of both the aerodynamic and bed-dilatancy thresholds (3). Because of Paschen discharge effects in the martian atmosphere, the electrostatic charging in a saltation cloud may be partially abated, but this will lead to greater grain mobility, more charging, and thus to a charge-discharge steady state mediated by mechanical interactions. II. Dry colluvial systems: Sand avalanches on dunes, dry debris flows, talus flows, avalanches, and pyroclastic surges are examples of gravity-driven, dense granular flows where rock/grain fragmentation and grain-to-grain interactions cause triboelectrification (sometimes augmented by other electrical charging processes), and where the grain densities of the systems are such that strong dipole-dipole interactions between grains might be expected to be present. Because it is expected that the Coulombic forces between grains will cause a sluggishness or enhanced granular-flow viscosity, the motion of a grain mass will be retarded or damped so that this will assist, ultimately, in terminating the flow. The greatest Coulombic viscosity will be created in the most highly charged systems, which will also be the most energetic. Thus, grain flows have some tendency to be self-limiting by internal energy partitioning; gravitational potential is converted to Coulombic potential, which manifests itself as a drag force between the grains. III. Volcanic eruption plumes and impact ejecta curtains: The violence of these systems leads to powerful electrical charging of particulates. Lightning storms emanating from volcanic plumes are a testimony to the levels of charging. As pyroclastic grains interact forcefully and frequently within eruption plumes, it is reasonable to predict that the internal turbulent motions of the plume will be significantly damped by the Coulombic viscosity exerted by grain charges. Additional information is contained in the original.

Marshall, J. R.↗

Interactions of amorphous Ta(x)Cu(1-x) (x = 0.93 and 0.80) alloy films with Au overlayers and GaAs substrates

Amorphous Ta(93)Cu(7) and Ta(80)Cu(20) alloy films are prepared by cosputtering of pure Ta and pure Cu targets with a rotating sample holder table. To investigate the possible application of these materials as diffusion barriers for the Au-GaAs system, vacuum annealings are made in the temperature range from 200 to 800 C. Resistivity change, X-ray diffraction, and Auger electron spectroscopy measurements are performed to find the chemical and metallurgical stabilities of these materials in this system. The reaction temperature for Ta(x)Cu(1-x) in contact with GaAs lies between 500 and 700 C. For Au in contact with Ta(x)Cu(1-x) the reaction occurs at about 600 C. Amorphous Ta(93)Cu(7) shows different interdiffusion characteristics with surrounding elements than does Ta(80)Cu(20).

Oh, Jae E.↗

Position and force control of coordinated multiple arms

A technique is presented for controlling multiple manipulators which are holding a single object and therefore form a closed kinematic chain. The object, which may or may not be in contact with a rigid environment, is assumed to be held rigidly by n robot end-effectors. The derivation is based on setting up constraint equations which reduce the 6 x n degrees of freedom of n manipulators each having six joints. Additional constraint equations are considered when one or more degrees of freedom of the object are reduced due to external constraints. Utilizing the operational space dynamic equations, a decoupling controller is designed to control both the position and the interaction forces of the object with the environment. Simulation results for the control of a pair of two-link manipulators are presented.

Hayati, Samad A.↗

Dynamics and control of coordinated multiple manipulators

A technique is presented for controlling multiple manipulators which are holding a single object and therefore form a closed kinematic chain. The object, which may or may not be in contact with a rigid environment, is assumed to be held rigidly by robot end-effectors. The derivation is based on setting up constraint equations which reduce the 6 x n degrees of freedom of a manipulators each having six joints. Additional constraint equations are considered when one or more of the degrees of freedom of the object is reduced due to external constraints. Utilizing the operational space dynamics equations, a decoupling controller is designed to control both the position and the interaction forces of the object with the environment. Finally, simulation results for the control of a pair of two-link manipulators are presented.

Hayati, S. A.↗

Computational techniques for high-speed flows with viscous and chemical effects

Algorithms for solving the Euler and the Navier-Stokes equations in conjunction with chemical kinetic equations are presented. The convective flux is estimated from a quasi one dimensional interpolation procedure. Shock, contact, and expansion waves and thermochemical nonequilibrium phenomena are captured by the Lax-Friedrichs technique. Relaxation techniques were developed to enhance their effectiveness in dealing with spatial and temporal stiffness associated with the physical problems. Both explicit and implicit smoothers were implemented into the standard multigrid time stepping method. Unsteady and steady scalar problems are discussed. A perfect gas and equilibrium air shock tube problem is investigated. Numerical schemes and techniques are compared for the problems of shock and boundary layer interaction and three dimensional viscous, nonequilibrium flow encompassing an aerobrake. The results are comparable in accuracy against other high order non-oscillatory techniques. The multigrid methods are assessed using a Mach 8 flow over a complete planar body, a sphere, and a blunt delta wing at 20 deg incidence. Applying an implicit multigrid method on a nested grid of 128 by 64 nodes the reduction factor is 0.25. The central processing unit reduction factor is 2.2 after both the single and multigrid Runge-Kutta solutions converged to machine zero on a grid of 37 by 41 by 73 nodes.

Li, C. P.↗

Experimental Investigation of Pool Boiling Heat Transfer Enhancement in Microgravity in the Presence of Electric Fields

Boiling is an effective mode of heat transfer since high heat flux levels are possible driven by relatively small temperature differences. The high heat transfer coefficients associated with boiling have made the use of these processes increasingly attractive to aerospace engineering. Applications of this type include compact evaporators in the thermal control of aircraft avionics and spacecraft environments, heat pipes, and use of boiling to cool electronic equipment. In spite of its efficiency, cooling based on liquid-vapor phase change processes has not yet found wide application in aerospace engineering due to specific problems associated with the low gravity environment. After a heated surface has reached the superheat required for the initiation of nucleate boiling, bubbles will start forming at nucleation sites along the solid interface by evaporation of the liquid. Bubbles in contact with the wall will continue growing by this mechanism until they detach. In terrestrial conditions, bubble detachment is determined by the competition between body forces (e.g. buoyancy) and surface tension forces that act to anchor the bubble along the three phase contact line. For a given body force potential and a balance of tensions along the three phase contact line, bubbles must reach a critical size before the body force can cause them to detach from the wall. In a low gravity environment the critical bubble size for detachment is much larger than under terrestrial conditions, since buoyancy is a less effective means of bubble removal. Active techniques of heat transfer enhancement in single phase and phase change processes by utilizing electric fields have been the subject of intensive research during recent years. The field of electrohydrodynamics (EHD) deals with the interactions between electric fields, flow fields and temperature fields. Previous studies indicate that in terrestrial applications nucleate boiling heat transfer can be increased by a factor of 50 as compared to values obtained for the same system without electric fields. Imposing an external electric field holds the promise to improve pool boiling heat transfer in low gravity, since a phase separation force other than gravity is introduced. The goal of our research is to experimentally investigate the potential of EHD and the mechanisms responsible for EHD heat transfer enhancement in boiling in low gravity conditions.

Herman, Cila↗

X-Windows PVT Widget Class

The X-Windows Process Validation Table (PVT) Widget Class ( Class is used here in the object-oriented-programming sense of the word) was devised to simplify the task of implementing network registration services for Information Sharing Protocol (ISP) graphical-user-interface (GUI) computer programs. Heretofore, ISP PVT programming tasks have required many method calls to identify, query, and interpret the connections and messages exchanged between a client and a PVT server. Normally, programmers have utilized direct access to UNIX socket libraries to implement the PVT protocol queries, necessitating the use of many lines of source code to perform frequent tasks. Now, the X-Windows PVT Widget Class encapsulates ISP client server network registration management tasks within the framework of an X Windows widget. Use of the widget framework enables an X Windows GUI program to interact with PVT services in an abstract way and in the same manner as that of other graphical widgets, making it easier to program PVT clients. Wrapping the PVT services inside the widget framework enables a programmer to treat a PVT server interface as though it were a GUI. Moreover, an alternate subclass could implement another service in a widget of the same type. This program was written by Matthew R. Barry of United Space Alliance for Johnson Space Center. For further information, contact the Johnson Technology Transfer Office at (281) 483-3809. MSC-23582 Shuttle Data Center File- Processing Tool in Java A Java-language computer program has been written to facilitate mining of data in files in the Shuttle Data Center (SDC) archives. This program can be executed on a variety of workstations or via Web-browser programs. This program is partly similar to prior C-language programs used for the same purpose, while differing from those programs in that it exploits the platform-neutrality of Java in implementing several features that are important for analysis of large sets of time-series data. The program supports regular expression queries of SDC archive files, reads the files, interleaves the time-stamped samples according to a chosen output, then transforms the results into that format. A user can choose among a variety of output file formats that are useful for diverse purposes, including plotting, Markov modeling, multivariate density estimation, and wavelet multiresolution analysis, as well as for playback of data in support of simulation and testing.

Barry, Matthew R.↗

Tactual interfaces: The human perceiver

Increasingly complex human-machine interactions, such as in teleoperation or in virtual environments, have necessitated the optimal use of the human tactual channel for information transfer. This need leads to a demand for a basic understanding of how the human tactual system works, so that the tactual interface between the human and the machine can receive the command signals from the human, as well as display the information to the human, in a manner that appears natural to the human. The tactual information consists of two components: (1) contact information which specifies the nature of direct contact with the object; and (2) kinesthetic information which refers to the position and motion of the limbs. This paper is mostly concerned with contact information.

Srinivasan, M. A.↗

Interaction of an interplanetary shock with the heliospheric plasma sheet

Interplanetary shocks often propagate along the heliospheric plasma sheet (HPS) where the interplanetary magnetic field (IMF) changes its polarity. This problem is investigated by the time-dependent 2.5-D MHD numerical model in the meridional plane. An example of computation is shown in the figure using density (log) contours and IMF vectors. Values of plasma parameters along the HPS fluctuate in time due to the Kelvin-Helmholtz instability. The HPS with its decreased intensity of the IMF as well as with its increased mass density causes a dimple in the shock structure (relatively weak for the forward shock, significant for the reverse shock, and very large for the contact discontinuity). Beyond the forward shock, the HPS is slightly compressed due to the post-shock increase of the azimuthal IMF component. Then follows expansion of the HPS surrounded by the highly-deformed contact discontinuity. A significant draping of IMF lines occurs around this structure that increases the meridional component of the IMF. This can cause a favorable condition for initiation of a geomagnetic storm.

Odstrcil, D.↗