Results for “consumption potential” — Page 24

NASA NTRS2001

MEMS-Based Satellite Micropropulsion Via Catalyzed Hydrogen Peroxide Decomposition

Micro-electromechanical systems (MEMS) techniques offer great potential in satisfying the mission requirements for the next generation of "micro-scale" satellites being designed by NASA and Department of Defense agencies. More commonly referred to as "nanosats", these miniature satellites feature masses in the range of 10-100 kg and therefore have unique propulsion requirements. The propulsion systems must be capable of providing extremely low levels of thrust and impulse while also satisfying stringent demands on size, mass, power consumption and cost. We begin with an overview of micropropulsion requirements and some current MEMS-based strategies being developed to meet these needs. The remainder of the article focuses the progress being made at NASA Goddard Space Flight Center towards the development of a prototype monopropellant MEMS thruster which uses the catalyzed chemical decomposition of high concentration hydrogen peroxide as a propulsion mechanism. The products of decomposition are delivered to a micro-scale converging/diverging supersonic nozzle which produces the thrust vector; the targeted thrust level approximately 500 N with a specific impulse of 140-180 seconds. Macro-scale hydrogen peroxide thrusters have been used for satellite propulsion for decades; however, the implementation of traditional thruster designs on a MEMS scale has uncovered new challenges in fabrication, materials compatibility, and combustion and hydrodynamic modeling. A summary of the achievements of the project to date is given, as is a discussion of remaining challenges and future prospects.

Hitt, Darren L.↗

NASA NTRS1981

JT8D high pressure compressor performance improvement

An improved performance high pressure compressor with potential application to all models of the JT8D engine was designed. The concept consisted of a trenched abradable rubstrip which mates with the blade tips for each of the even rotor stages. This feature allows tip clearances to be set so blade tips run at or near the optimum radius relative to the flowpath wall, without the danger of damaging the blades during transients and maneuvers. The improved compressor demonstrated thrust specific fuel consumption and exhaust gas temperature improvements of 1.0 percent and at least 10 C over the takeoff and climb power range at sea level static conditions, compared to a bill-of-material high pressure compressor. Surge margin also improved 4 percentage points over the high power operating range. A thrust specific fuel consumption improvement of 0.7 percent at typical cruise conditions was calculated based on the sea level test results.

Gaffin, W. O.↗

NASA NTRS2006

Projecting Future Urbanization with Prescott College's Spatial Growth Model to Promote Environmental Sustainability and Smart Growth, A Case Study in Atlanta, Georgia

Planning is an integral element of good management and necessary to anticipate events not merely respond to them. Projecting the quantity and spatial distribution of urban growth is essential to effectively plan for the delivery of city services and to evaluate potential environmental impacts. The major drivers of growth in large urban areas are increasing population, employment opportunities, and quality of life attractors such as a favorable climate and recreation opportunities. The spatial distribution of urban growth is dictated by the amount and location of developable land, topography, energy and water resources, transportation network, climate change, and the existing land use configuration. The Atlanta region is growing very rapidly both in population and the consumption of forestland or low-density residential development. Air pollution and water availability are significant ongoing environmental issues. The Prescott Spatial Growth Model (SGM) was used to make growth projections for the metropolitan Atlanta region to 2010,2020 and 2030 and results used for environmental assessment in both business as usual and smart growth scenarios. The Prescott SGM is a tool that uses an ESRI ArcView extension and can be applied at the parcel level or more coarse spatial scales and can accommodate a wide range of user inputs to develop any number of growth rules each of which can be weighted depending on growth assumptions. These projections were used in conjunction with meteorological and air quality models to evaluate future environmental impacts. This presentation will focus on the application of the SGM to the 13-County Atlanta Regional Commission planning jurisdiction as a case study. The SGM will be described, including how rule sets are developed and the decision process for allocation of future development to available land use categories. Data inputs required to effectively run the model will be discussed. Spatial growth projections for ten, twenty, and thirty year planning horizons will be presented and results discussed, including regional climate and air quality impacts.

Estes, Maurice G., Jr.↗

NASA NTRS2008

Disturb testing in flash memories

Non-volatile memory technology as defined by NAND architecture flash memory continues to lead the process scaling and device shrinking efforts of the entire integrated circuit industry. 45- nm technology nodes are now producing commercial 32Gb devices. These latest 32Gb devices are pioneering new charge trapping memory cell technologies using metal gates and high-k dielectric materials. These cells are called TANOS and consist of tantalum-nitride, aluminum oxide (high k material), nitride, oxide, and silicon. Such high-density memories continue to revolutionize commercial electronics in terms of new high-speed data architectures and significant reductions in overall power and weight consumption. In stark contrast, nearly all science-based interplanetary and earth-orbiting NASA spacecraft are still designing in and around mid-1980s-level non-volatile technology with 1Mb Electrically Erasable Read-Only Memory (EEPROM) devices. NASA has typically shunned the use of modern flash devices because of radiation and reliability concerns due to the commercial-offthe– shelf (COTS) nature of the NAND flash technology. Given the significant potential increases in overall system capability these modern flash devices could bring to NASA missions, it is important to continue to investigate these devices. This report will investigate certain portions of the reliability performance of NAND flash devices, specifically the disturb properties. Understanding the possible limitations such new non-volatile memory technology presents to NASA is the goal of this report.

Freie, Michael↗

NASA NTRS1994

Release and Consumption of DMSP from Emiliania Huxleyi during grazing by Oxyrrhis Marina

Degradation and release to solution of intracellular dimethylsulfoniopropionate (DMSP) from Emiliania huxleyi 370 was observed during grazing by the heterotrophic dinoflagellate Oxyrrhis marina in 24 h bottle incubations. Between 30 and 70% of the lost algal DMSP was metabolized by the grazers without production of dimethylsulfide (DMS) when grazer densities were 150 to 450/ml. The rest was released to solution and about 30% was converted to DMS by bacteria associated with the grazer culture. These experiments demonstrate that grazing by herbivorous protists may be an important sink for DMSP in marine waters, removing a potential source of DMS. Microzooplankton grazing may also indirectly increase the production of DMS by transferring algal DMSP to the dissolved pool, making it available for bacterial metabolism.

Wolfe, Gordon V.↗

NASA NTRS2008

Towards Intelligent Control for Next Generation Aircraft

NASA Aeronautics Subsonic Fixed Wing Project is focused on mitigating the environmental and operation impacts expected as aviation operations triple by 2025. The approach is to extend technological capabilities and explore novel civil transport configurations that reduce noise, emissions, fuel consumption and field length. Two Next Generation (NextGen) aircraft have been identified to meet the Subsonic Fixed Wing Project goals - these are the Hybrid Wing-Body (HWB) and Cruise Efficient Short Take-Off and Landing (CESTOL) aircraft. The technologies and concepts developed for these aircraft complicate the vehicle s design and operation. In this paper, flight control challenges for NextGen aircraft are described. The objective of this paper is to examine the potential of state-of-the-art control architectures and algorithms to meet the challenges and needed performance metrics for NextGen flight control. A broad range of conventional and intelligent control approaches are considered, including dynamic inversion control, integrated flight-propulsion control, control allocation, adaptive dynamic inversion control, data-based predictive control and reinforcement learning control.

Acosta, Diana Michelle↗

NASA NTRS1978

Fuel consumption improvement in current transport engines

A review is conducted of improvements which can be made with respect to the fuel consumption of current engines and new production versions of current engines. A description is presented of an engine diagnostics program which has the objective to identify and quantify the causes and sources of performance deterioration in the JT9D turbofan engine and to develop basic data which will be applied to minimize performance degradation of current and future engines. General areas where performance losses occur are examined, taking into account seals, blades and vanes, and cases. Potential performance improvement concepts are related to improved component aerodynamics, improved flowpath sealing, blade tip clearance control, improved turbine cooling effectiveness, improved turbine materials and coatings, duct and nozzle aerodynamic refinements, nacelle aerodynamic refinements, forced exhaust mixers, advanced nacelle materials, and advanced fuel control.

Hines, R. W.↗

NASA NTRS1986

Compound cycle engine for helicopter application

The Compound Cycle Engine (CCE) is a highly turbocharged, power compounded, ultra-high power density, light-weight diesel engine. The turbomachinery is similar to a moderate pressure ratio, free power turbine engine and the diesel core is high speed and a low compression ratio. This engine is considered a potential candidate for future military light helicopter applications. This executive summary presents cycle thermodynamic (SFC) and engine weight analyses performed to establish general engine operating parameters and configuration. An extensive performance and weight analysis based on a typical two hour helicopter (+30 minute reserve) mission determined final conceptual engine design. With this mission, CCE performance was compared to that of a T-800 class gas turbine engine. The CCE had a 31% lower-fuel consumption and resulted in a 16% reduction in engine plus fuel and fuel tank weight. Design SFC of the CCE is 0.33 lb-HP-HR and installed wet weight is 0.43 lbs/HP. The major technology development areas required for the CCE are identified and briefly discussed.

Castor, Jere G.↗

NASA NTRSDate not supplied

Appetite and Food Intake During 11 Days of Mild Hypobaric Hypoxia

Introduction Reduced food consumption and loss of body mass and muscle mass have been observed during spaceflight. Hypoxic conditions that astronauts may encounter on exploration missions may further implicate satiety signals and dietary intake. Appetite, food intake, and satiety hormones were investigated under the conditions of mild hypoxia and high energy output during simulated extravehicular activity (EVA) to determine the adequacy of a mission relevant space food system to support energy balance and body composition. Methods Foods realistic to early Artemis missions was packed by meal for each subject for the 11-day test based on estimated energy requirements (EER) and estimated EVA caloric requirements. No hot water or food warmer was provided and only room temperature water was available to rehydrate food and beverages in-mission, mimicking plans for early Artemis missions. Measures included food records (pre-mission, in-mission); fasted body weight (pre-mission, in-mission); Dual-energy X-ray absorptiometry (DXA) (pre-mission, post-mission); subjective ratings and feedback of food acceptability, mealtime and meal preparation sufficiency, appetite, and nausea (in-mission); and circulating ghrelin and leptin concentration in fasted blood samples (pre-mission, in-mission: pre-post EVA). Results All subjects consumed fewer calories in-mission than predicted. On average, subjects consumed 341 calories less on EVA days compared to non-EVA days in-mission (p=0.0511). The total weight loss estimate from daily weight measurements (-1.1 kg, p=0.0028) is consistent with underconsumption and supported by DXA measurements (-1.3 kg total body mass, p=0.0123 and -1.6 kg fat mass, p=0.0016). In general, most foods that were consumed were given acceptable scores, but subject comments indicated that the most acceptable foods were those not intended to be heated. Comments also indicated that subjects found their favorite foods early in the mission and avoided the foods that they did not like throughout the mission. Habitability scores indicated that overall aspects of the food system were considered borderline or unacceptable over the length of this mission. Foods that caused gas were avoided pre-EVA to prevent discomfort during pressure changes. Average fruit and vegetable intake decreased during the mission, dropping from 4.8 servings/d pre-mission to 3.4 servings/d on non-EVA days in-mission (p=0.0872) and 2.3 servings on EVA days (p=0.0020). Fasting ghrelin concentrations tended to be lower pre-EVA and on non-EVA days when exposed to mild hypoxia compared to normoxic conditions pre-mission and post-EVA (p=0.0136). Fasting levels of leptin did not change. Discussion Food intake was reduced in-mission, resulting in a caloric deficit and weight loss for most subjects. Crew food and appetite ratings and comments indicated this was due to a combination of food choices, lack of preference, lack of preparation capability, lack of time for meal preparation, consumption, and cleanup, and physiological challenges with the changing pressure. The regulation of appetite stimulating hormone ghrelin, but not the appetite suppressor leptin, appeared to be sensitive to hypoxic conditions. Conclusions Food preparation capabilities and time for meals are important for promoting adequate food intake. Reduced appetite and food intake during missions may further be aggravated under hypoxic conditions through the suppression of ghrelin. Lack of time for meals on EVA days, and avoidance of potential gas-causing foods (e.g., health promoting fruits and vegetables) prior to EVAs, demonstrate the importance of scheduling ample recovery time between EVA days.

Grace L Douglas↗

NASA NTRS2023

Appetite and Food Intake During 11 Days of Mild Hypobaric Hypoxia

Introduction Reduced food consumption and loss of body mass and muscle mass have been observed during spaceflight. Hypoxic conditions that astronauts may encounter on exploration missions may further implicate satiety signals and dietary intake. Appetite, food intake, and satiety hormones were investigated under the conditions of mild hypoxia and high energy output during simulated extravehicular activity (EVA) to determine the adequacy of a mission relevant space food system to support energy balance and body composition. Methods Foods realistic to early Artemis missions was packed by meal for each subject for the 11-day test based on estimated energy requirements (EER) and estimated EVA caloric requirements. No hot water or food warmer was provided and only room temperature water was available to rehydrate food and beverages in-mission, mimicking plans for early Artemis missions. Measures included food records (pre-mission, in-mission); fasted body weight (pre-mission, in-mission); Dual-energy X-ray absorptiometry (DXA) (pre-mission, post-mission); subjective ratings and feedback of food acceptability, mealtime and meal preparation sufficiency, appetite, and nausea (in-mission); and circulating ghrelin and leptin concentration in fasted blood samples (pre-mission, in-mission: pre-post EVA). Results All subjects consumed fewer calories in-mission than predicted. On average, subjects consumed 341 calories less on EVA days compared to non-EVA days in-mission (p=0.0511). The total weight loss estimate from daily weight measurements (-1.1 kg, p=0.0028) is consistent with underconsumption and supported by DXA measurements (-1.3 kg total body mass, p=0.0123 and -1.6 kg fat mass, p=0.0016). In general, most foods that were consumed were given acceptable scores, but subject comments indicated that the most acceptable foods were those not intended to be heated. Comments also indicated that subjects found their favorite foods early in the mission and avoided the foods that they did not like throughout the mission. Habitability scores indicated that overall aspects of the food system were considered borderline or unacceptable over the length of this mission. Foods that caused gas were avoided pre-EVA to prevent discomfort during pressure changes. Average fruit and vegetable intake decreased during the mission, dropping from 4.8 servings/d pre-mission to 3.4 servings/d on non-EVA days in-mission (p=0.0872) and 2.3 servings on EVA days (p=0.0020). Fasting ghrelin concentrations tended to be lower pre-EVA and on non-EVA days when exposed to mild hypoxia compared to normoxic conditions pre-mission and post-EVA (p=0.0136). Fasting levels of leptin did not change. Discussion Food intake was reduced in-mission, resulting in a caloric deficit and weight loss for most subjects. Crew food and appetite ratings and comments indicated this was due to a combination of food choices, lack of preference, lack of preparation capability, lack of time for meal preparation, consumption, and cleanup, and physiological challenges with the changing pressure. The regulation of appetite stimulating hormone ghrelin, but not the appetite suppressor leptin, appeared to be sensitive to hypoxic conditions. Conclusions Food preparation capabilities and time for meals are important for promoting adequate food intake. Reduced appetite and food intake during missions may further be aggravated under hypoxic conditions through the suppression of ghrelin. Lack of time for meals on EVA days, and avoidance of potential gas-causing foods (e.g., health promoting fruits and vegetables) prior to EVAs, demonstrate the importance of scheduling ample recovery time between EVA days.

Lichar Dillon↗

NASA NTRSDate not supplied

Implementation of Active Sites in DSMC to Capture Pitting of Oxidizing Carbon Materials

In this work we demonstrate a newly developed capability to capture pitting of carbon fibers in DSMC simulations, specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. State-of-the-art reactive surface models in DSMC compute collision dependent carbon consumption rates (usually through desorption of CO) based on a set of surface reactions that has been derived from molecular beam experiments. The reactivity on each carbon surface element is constant in those models, such that the carbon surface recedes uniformly as a result of ablation. However, it is well known that in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. These defective sites have a much higher reactivity than the average sites (2-3 orders of magnitude) and are first to react during ablation leading to its removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these ”active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various reaction mechanisms such as adsorption, desorption, Eley-Rideal (ER) and Langmuir-Hinshelwood (LH) mechanisms. Within this framework, we have implemented the capability of a single surface having multiple site sets with different reactivities. Using this feature, we can simulate the presence of active sites on carbon surfaces, whose reactivity is much greater than an average site as a result of defects. We have implemented the active site fraction as a property of surface elements within SPARTA, which is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface, and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we are able to capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRS2011

Insect Residue Contamination on Wing Leading Edge Surfaces: A Materials Investigation for Mitigation

Flight tests have shown that residue from insect strikes on aircraft wing leading edge surfaces may induce localized transition of laminar to turbulent flow. The highest density of insect populations have been observed between ground level and 153 m during light winds (2.6 -- 5.1 m/s), high humidity, and temperatures from 21 -- 29 C. At a critical residue height, dependent on the airfoil and Reynolds number, boundary layer transition from laminar to turbulent results in increased drag and fuel consumption. Although this represents a minimal increase in fuel burn for conventional transport aircraft, future aircraft designs will rely on maintaining laminar flow across a larger portion of wing surfaces to reduce fuel burn during cruise. Thus, insect residue adhesion mitigation is most critical during takeoff and initial climb to maintain laminar flow in fuel-efficient aircraft configurations. Several exterior treatments investigated to mitigate insect residue buildup (e.g., paper, scrapers, surfactants, flexible surfaces) have shown potential; however, implementation has proven to be impractical. Current research is focused on evaluation of wing leading edge surface coatings that may reduce insect residue adhesion. Initial work under NASA's Environmentally Responsible Aviation Program focused on evaluation of several commercially available products (commercial off-the-shelf, COTS), polymers, and substituted alkoxy silanes that were applied to aluminum (Al) substrates. Surface energies of these coatings were determined from contact angle data and were correlated to residual insect excrescence on coated aluminum substrates using a custom-built "bug gun." Quantification of insect excrescence surface coverage was evaluated by a series of digital photographic image processing techniques.

Lorenzi, Tyler M.↗

NASA NTRS2016

Evolving Our Evaluation of Lighting Environments Project

Imagine you are an astronaut on their 100th day of your three year exploration mission. During your daily routine to the small hygiene compartment of the spacecraft, you realize that no matter what you do, your body blocks the light from the lamp. You can clearly see your hands or your toes but not both! What were those design engineers thinking! It would have been nice if they could have made the walls glow instead! The reason the designers were not more innovative is that their interpretation of the system lighting requirements didn't allow them to be so! Currently, our interior spacecraft lighting standards and requirements are written around the concept of a quantity of light illuminating a spacecraft surface. The natural interpretation for the engineer is that a lamp that throws light to the surface is required. Because of certification costs, only one lamp is designed and small rooms can wind up with lamps that may be inappropriate for the room architecture. The advances in solid state light emitting technologies and optics for lighting and visual communication necessitates the evaluation of how NASA envisions spacecraft lighting architectures and how NASA uses industry standards for the design and evaluation of lighting system. Current NASA lighting standards and requirements for existing architectures focus on the separate ability of a lighting system to throw light against a surface or the ability of a display system to provide the appropriate visual contrast. Realization that these systems can be integrated is not realized. The result is that the systems are developed independent from one another and potential efficiencies that could be realized from borrowing from the concept of one technology and applying it for the purpose of the other does not occur. This project investigated the possibility of incorporating large luminous surface lamps as an alternative or supplement to overhead lighting. We identified existing industry standards for architectural luminous or brightness uniformity as part of a lighting system definition. The efficiency of the surface lighting technology was evaluated for uniformity and power consumption. Finally, the team investigated possible performance savings if the walls were made to glow via a self luminous surface system instead of creating brightness by use of direct lighting of a highly reflective diffuse surface.

Terrier, Douglas↗

NASA NTRS1986

Multiple Application Propfan Study (MAPS): Advanced tactical transport

This study was conducted to ascertain potential benefits of a propfan propulsion system application to a blended wing/body military tactical transport. Based on a design cruise Mach no. of 0.75 for the design mission, the results indicate a significant advantage in various figures of merit for the propfan over those of a comparable technology turbofan. Although the propfan has a 1.6 percent greater takeoff gross weight, its life cycle cost is 5.3 percent smaller, partly because of a 27 percent smaller specific fuel consumption. When employed on alternate missions, the propfan configuration offers significantly improved flexibility and capability: an increase in sea level penetration distance of more than 100 percent, or in time-on-station of 24 percent, or in deployment payload of 38 percent.

Newton, F. C.↗

NASA NTRSDate not supplied

Implementation of active sites to capture pitting of oxidizing carbon materials in DSMC.

In this work we demonstrate a newly developed capability to capture pitting of carbon fibers in DSMC simulations, specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code [1]. State-of-the-art reactive surface models in DSMC compute collision dependent carbon consumption rates (usually through desorption of CO) based on a set of surface reactions that has been derived from molecular beam experiments [2]. The reactivity on each carbon surface element is constant in those models, such that the carbon surface recedes uniformly as a result of ablation. However, it is well known that in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale [3]. These defective sites have a much higher reactivity than the average sites (2-3 orders of magnitude) and are first to react during ablation leading to its removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these ”active” sites (as shown in Fig. 1). In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various reaction mechanisms such as adsorption, desorption, Eley-Rideal (ER) and Langmuir-Hinshelwood (LH) mechanisms [4]. Within this framework, we have implemented the capability of a single surface having multiple site sets with different reactivities. Using this feature, we can simulate the presence of active sites on carbon surfaces, whose reactivity is much greater than an average site as a result of defects. We have implemented the active site fraction as a property of surface elements within SPARTA, which is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface, and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we are able to capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRS1993

An estimate of the second law thermodynamic efficiency of the various units comprising an Environmental Control and Life Support System (ECLSS)

The objective of this paper is to present an estimate of the second law thermodynamic efficiency of the various units comprising an Environmental Control and Life Support System (ECLSS). The technique adopted here is based on an evaluation of the 'lost work' within each functional unit of the subsystem. Pertinent information for our analysis is obtained from a user interactive integrated model of an ECLSS. The model was developed using ASPEN. A potential benefit of this analysis is the identification of subsystems with high entropy generation as the most likely candidates for engineering improvements. This work has been motivated by the fact that the design objective for a long term mission should be the evaluation of existing ECLSS technologies not only the basis of the quantity of work needed for or obtained from each subsystem but also on the quality of work. In a previous study Brandhorst showed that the power consumption for partially closed and completely closed regenerable life support systems was estimated as 3.5 kw/individual and 10-12 kw/individual respectively. With the increasing cost and scarcity of energy resources, our attention is drawn to evaluate the existing ECLSS technologies on the basis of their energy efficiency. In general the first law efficiency of a system is usually greater than 50 percent. From literature, the second law efficiency is usually about 10 percent. The estimation of second law efficiency of the system indicates the percentage of energy degraded as irreversibilities within the process. This estimate offers more room for improvement in the design of equipment. From another perspective, our objective is to keep the total entropy production of a life support system as low as possible and still ensure a positive entropy gradient between the system and the surroundings. The reason for doing so is as the entropy production of the system increases, the entropy gradient between the system and the surroundings decreases, and the system will gradually approach equilibrium with the surroundings until it reaches the point where the entropy gradient is zero. At this point no work can be extracted from the system. This is called the 'dead state' of the system.

Chatterjee, Sharmista↗

NASA NTRS2007

Potential for Measurement of Trace Volatile Organic Compounds in Closed Environments Using Gas Chromatograph/Differential Mobility Spectrometer

For nearly 3.5 years, the Volatile Organic Analyzer (VOA) has routinely analyzed the International Space Station (ISS) atmosphere for a target list of approximately 20 volatile organic compounds (VOCs). Additionally, an early prototype of the VOA collected data aboard submarines in two separate trials. Comparison of the data collected on ISS and submarines showed a surprising similarity in the atmospheres of the two environments. Furthermore, in both cases it was demonstrated that the VOA data can detect hardware issues unrelated to crew health. Finally, it was also clear in both operations that the VOA s size and resource consumption were major disadvantages that would restrict its use in the future. The VOA showed the value of measuring VOCs in closed environments, but it had to be shrunk if it was to be considered for future operations in these environments that are characterized by cramped spaces and limited resources. The Sionex Microanalyzer is a fraction of the VOA s size and this instrument seems capable of maintaining or improving upon the analytical performance of the VOA. The two design improvements that led to a smaller, less complex instrument are the Microanalyzer s use of recirculated air as the gas chromatograph s carrier gas and a micromachined detector. Although the VOA s ion mobility spectrometer and the Microanalyzer s differential mobility spectrometer (DMS) are related detector technologies, the DMS was more amenable to micromachining. This paper will present data from the initial assessment of the Microanalyzer. The instrument was challenged with mixtures that simulated the VOCs typically detected in closed-environment atmospheres.

Limero, Thomas↗

NASA NTRS1977

Alternative fuels

Potential problems related to the use of alternative aviation turbine fuels are discussed and both ongoing and required research into these fuels is described. This discussion is limited to aviation turbine fuels composed of liquid hydrocarbons. The advantages and disadvantages of the various solutions to the problems are summarized. The first solution is to continue to develop the necessary technology at the refinery to produce specification jet fuels regardless of the crude source. The second solution is to minimize energy consumption at the refinery and keep fuel costs down by relaxing specifications.

Grobman, J. S.↗