Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “component isolation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Traveling wave tube circuit

A traveling wave tube (TWT) has a slow wave structure (SWS) which is severed into two or more sections. A signal path, connects the end of an SWS section to the beginning of the following SWS section. The signal path comprises an impedance matching coupler (IMC), followed by an isolator, a variable phase shifter, and a second IMC. The aggregate band pass characteristic of the components in the signal path is chosen to reject, or strongly attenuate, all frequencies outside the desired operating frequency range of the TWT and yet pass, with minimal attenuation in the forward direction, all frequencies within the desired operating frequency range. The isolator is chosen to reject, or strongly attenuate, waves, of all frequencies, which propagate in the backward direction. The aggregate phase shift characteristic of the components in the signal path is chosen to apply signal power to the beginning of the following SWS section with the phase angle yielding maximum efficiency.

Connolly, D. J.↗
NASA NTRS1989

Amphiphilic components of the Murchison carbonaceous chondrite - Surface properties and membrane formation

The possibility that the amphiphilic compounds in carbonaceous meteorites whose physicochemical properties are presently studied may represent sources of lipidlike compounds which could have evolved as membrane components in primitive cells is investigated in samples of the Murchison CM2 chondrite. Surface properties and membrane formation are obtained for three fractions isolated by two-dimensional thin-layer chromatography. It is concluded that a small, undefined fraction of Murchison components exhibits amphiphilic properties which allow assembly into boundary membranes.

Deamer, D. W.↗
NASA NTRS1990

Autonomous power expert system

The Autonomous Power Expert (APEX) system was designed to monitor and diagnose fault conditions that occur within the Space Station Freedom Electrical Power System (SSF/EPS) Testbed. APEX is designed to interface with SSF/EPS testbed power management controllers to provide enhanced autonomous operation and control capability. The APEX architecture consists of three components: (1) a rule-based expert system, (2) a testbed data acquisition interface, and (3) a power scheduler interface. Fault detection, fault isolation, justification of probable causes, recommended actions, and incipient fault analysis are the main functions of the expert system component. The data acquisition component requests and receives pertinent parametric values from the EPS testbed and asserts the values into a knowledge base. Power load profile information is obtained from a remote scheduler through the power scheduler interface component. The current APEX design and development work is discussed. Operation and use of APEX by way of the user interface screens is also covered.

Walters, Jerry L.↗
NASA NTRS1992

Size of metallic and polyethylene debris particles in failed cemented total hip replacements

Reports of differing failure rates of total hip prostheses made of various metals prompted us to measure the size of metallic and polyethylene particulate debris around failed cemented arthroplasties. We used an isolation method, in which metallic debris was extracted from the tissues, and a non-isolation method of routine preparation for light and electron microscopy. Specimens were taken from 30 cases in which the femoral component was of titanium alloy (10), cobalt-chrome alloy (10), or stainless steel (10). The mean size of metallic particles with the isolation method was 0.8 to 1.0 microns by 1.5 to 1.8 microns. The non-isolation method gave a significantly smaller mean size of 0.3 to 0.4 microns by 0.6 to 0.7 microns. For each technique the particle sizes of the three metals were similar. The mean size of polyethylene particles was 2 to 4 microns by 8 to 13 microns. They were larger in tissue retrieved from failed titanium-alloy implants than from cobalt-chrome and stainless-steel implants. Our results suggest that factors other than the size of the metal particles, such as the constituents of the alloy, and the amount and speed of generation of debris, may be more important in the failure of hip replacements.

Non-NASA Center↗
NASA NTRSDate not supplied

Design of A Transition-Edge-Sensor-Based Thermal Stabilization Stage

Electrothermal feedback in a transition edge sensor suppresses thermal fluctuations in the TES and regions in close thermal contact. We designed a heavily-metallized, leg-isolated membrane with a TES which serves as a thermal stabilization stage that can be lithographically integrated with other devices. Through modeling, fabrication and test of prototype devices, we examine whether the noise reduction in this stage can reduce thermal fluctuations (e.g. 1/f noise) in the other components by providing a more stable base temperature. In one implementation, a leg-isolated TES bolometer of higher superconducting transition temperature (Tc) is encircled by a second membrane region which is metallized and thermally stabilized by a second, lower-Tc TES. We present fabrication results on the dual-Tc design and testing of the simultaneous biasing of a two-stage, two-TES device. We explore varied heat capacity of the thermally stabilized stage in the single pixel design. We also present other designs to evaluate the use of an outer thermal stabilization stage for multiple pixel arrangements.

Rachel Borrelli↗
NASA NTRS2004

Solid oxidized fuel cells seals leakage setup and testing

As the world s reserves of fossil fuels are depleted, the U.S. Government, as well as other countries and private industries, is researching solutions for obtaining power, answers that would be more efficient and environmentally friendly. For a long time engineers have been trying to obtain the benefits of clean electric power without heavy batteries or pollution-producing engines. While some of the inventions proved to be effective (i.e. solar panels or windmills) their applications are limited due to dependency on the energy source (i.e. sun or wind). Currently, as energy concerns increase, research is being carried out on the development of a Solid Oxide Fuel Cell (SOFC). The United States government is taking a proactive role in expanding the technology through the Solid State Energy Conversion Alliance (SECA) Program, which is coordinated by the Department of Energy. into an electrical energy. This occurs by the means of natural tendency of oxygen and hydrogen to chemically react. While controlling the process, it is possible to harvest the energy given off by the reaction. SOFCs use currently available fossil fuels and convert a variety of those fuels with very high efficiency (about 40% more efficient than modem thermal power plants). At the same time they are almost entirely nonpolluting and due to their size they can be placed in remote areas. The main fields where the application of the fuel cells appears to be the most useful for are stationary energy sources, transportation, and military applications. structure and materials must be resolved. All the components must be operational in harsh environments including temperatures reaching 800 C and cyclic thermal- mechanical loading. Under these conditions, the main concern is the requirement for hermetic seals to: (1) prevent mixing of the fuel and oxidant within the stack, (2) prevent parasitic leakage of the fuel from the stack, (3) prevent contamination of the anode by air leaking into the stack, (4) electrically isolate the individual cells within the stack, and (5) mechanically bond the cell components. The sealing challenges are aggravated by the need to maintain hermetic boundaries between the different flow paths within the fuel cell throughout cycled operation. Within the timeframe of my tenure, the main objective is to assist in building a state-of-art test facility.

Bastrzyk, Marta B.↗
DOE OSTI2026

Design of a shipping fixture for a compact cryomodule hermetic assembly

In support of the development of a conduction-cooled 915MHz superconducting radio frequency (SRF) cryomodule, this study highlights the design of a shipping fixture for transporting the hermetic assembly 4500 km from Jefferson Lab to General Atomics in San Diego, California. The hermetic assembly consists of a 2-cell 915 MHz SRF cavity, a coaxial fundamental power coupler and warm-to-cold transition beam tubes. The two-part shipping assembly consists of an inner frame, providing direct mounting of the components, and an outer frame mounted to the ground transport vehicle. The inner frame is then connected to the outer frame by way of wire-rope isolators. Accelerometer data from ground transportation of previous projects at Jefferson Lab provides the baseline for the expected frequency and magnitude of vibrational and shock events during transit. Modal analyses were carried out in ANSYS on the inner frame assembly and critical components to identify an appropriate wire-rope isolator configuration such that peak loads are mitigated and the incurred frequencies do not correspond with the fundamental modes of the structures.

Accelerator Physics↗
DOE OSTI2022

Combustion characteristics and detailed simulations of surrogates for a Tier II gasoline certification fuel

An experimental and numerical study of combustion of a gasoline certification fuel (‘indolene’), and four (S4) and five (S5) component surrogates for it, is reported for the configurations of an isolated droplet burning with near spherical symmetry in the standard atmosphere, and a single cylinder engine designed for advanced compression ignition of pre-vaporized fuel. The intent was to compare performance of the surrogate for these different combustion configurations and to assess the broader applicability of the kinetic mechanism and property database for the simulations. A kinetic mechanism comprised of 297 species and 16,797 reactions was used in the simulations that included soot formation and evolution, and accounted for unsteady transport, liquid diffusion inside the droplet, radiative heat transfer, and variable properties. The droplet data showed a clear preference for the S5 surrogate in terms of burning rate. The simulations showed generally very good agreement with measured droplet, flame, and soot shell diameters. Measurements of combustion timing, in-cylinder pressure, and mass-averaged gas temperature were also well predicted with a slight preference for the S5 surrogate. Preferential vaporization was not evidenced from the evolution of droplet diameter but was clearly revealed in simulations of the evolution of mixture fractions inside the droplets. Here, the influence of initial droplet diameter (D o ) on droplet burning was strong, with S5 burning rates decreasing with increasing D o due to increasing radiation losses from the flame. Flame extinction was predicted for D o =3.0 mm as a radiative loss mechanism but not predicted for smaller D o for the conditions of the simulations.

42 ENGINEERING↗
DOE OSTI2021

Water Migration and Swelling in Engineered Barrier Materials for Radioactive Waste Disposal

Deep, underground repositories are needed to isolate radioactive waste from the biosphere. Because bentonite is an integral component of many multibarrier repository systems, information on the hydraulic behavior of bentonite is crucial for modeling the long-term viability of such systems. In this paper the hydraulic behavior of bentonite samples was analyzed as a function of aggregate size, and samples were subjected to hydrothermal treatments involving contact with NaCl, KCl, and deionized water. Neutron and X-ray imaging were used to quantify water sorption into packed bentonite samples and bentonite swelling into the water column. The distance between the original clay-water interface and the wetting front was determined as a function of time. Average water uptake exhibited a square-root-of-time dependence in freshly prepared samples, but more variable rates were observed for samples previously in contact with water. The radiography was supported by small-angle neutron scattering analysis and ultra-small-angle neutron scattering analysis of aggregate size distributions and by inelastic neutron scattering to understand the physicochemical environment of the sorbed water. Results showed that hydrothermal treatment with KCl had the greatest effect of increased water transport in the bentonite, possibly as a result of the interaction of K + with smectite layers in the clay.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Campylobacter jejuni resistance to human milk involves the acyl carrier protein AcpP

Campylobacter jejuni is a common foodborne pathogen worldwide that is associated with high rates of morbidity and mortality among infants in low- to middle-income countries (LMICs). Human milk provides infants with an important source of nutrients and contains antimicrobial components for protection against infection. However, recent studies, including our own, have found significantly higher levels of Campylobacter in diarrheal stool samples collected from breastfed infants compared to non-breastfed infants in LMICs. We hypothesized that C. jejuni has unique strategies to resist the antimicrobial properties of human milk. Transcriptional profiling found human milk exposure induces genes associated with ribosomal function, iron acquisition, and amino acid utilization in C. jejuni strains 81–176 and 11168. However, unidentified proteinaceous components of human milk prevent bacterial growth. Evolving both C. jejuni isolates to survive in human milk resulted in mutations in genes encoding the acyl carrier protein (AcpP) and the major outer membrane porin (PorA). Introduction of the PorA/AcpP amino acid changes into the parental backgrounds followed by electron microscopy showed distinct membrane architectures, and the AcpP changes not only significantly improved growth in human milk, but also yielded cells surrounded with outer membrane vesicles. Analyses of the phospholipid and lipooligosaccharide (LOS) compositions suggest an imbalance in acyl chain distributions. For strain 11168, these changes protect both evolved and 11168ΔacpP G33R strains from bacteriophage infection and polymyxin killing. Taken together, this study provides insights into how C. jejuni may evolve to resist the bactericidal activity of human milk and flourish in the hostile environment of the gastrointestinal tract.

60 APPLIED LIFE SCIENCES↗
NASA NTRS1965

Insulator-holder protects transistors in dense electronic assemblies

Molded insulating spacer with one or more cavities is used as an insulated holder for mounting metal-case transistors in a chassis containing densely packed electronic components. The transistors are mechanically supported on their bases and electrically isolated from each other by the holder.

Source record↗
NASA NTRS1977

Hydrogen maser frequency standards for the Deep Space Network

A field operable maser has been developed for use in the Deep Space Network. Maser design was based on two experimental hydrogen maser frequency standards in operation since 1970 at DSN stations. Many design changes have been incorporated into the maser design, both in physics and electronics systems. Short and long term frequency, RF isolation of maser output lines and the lifetime of active physics components have been improved. Automatic fault detection and location, and performance and reliability of the receiver-synthesizer system have also been altered.

Dachel, P. R.↗
NASA NTRS1982

Wideband Amplifier With Subpicosecond Stability

RF circuit offers high isolation as well as phase stability. For temperature stability, all circuit components are contained in closed metal housing; packages of active circuit elements are embedded in common heat sink. Provisions not only slow down effect of ambient temperature changes on individual devices but also reduce temperature differences across devices so that differential temperature effects vanish.

Reinhardt, V. S.↗
NASA NTRS1984

Attitude, control and stabilization

In the area of control, several problems can arise during the evolution of the space station. These incude: 1) the use of multiple or articulated flexible bodies; 2) the need for distributed cntrol for maneuvering and maintaining altitude; 3) hierarchical control to automate and manage control systems; 4) structual control (from the standpoint of appendage stamping; isolation, and possible figure control); 5) cntrol position and orientation for component modules during construction (an evolutionary requirement); 6) control during docking and undocking operations; and 7) the normal requirements for stablity and control during systems operations. In addition, there are a number of key technology concerns, such as significant landing modes which tend to be closely spaced and distributed widely, distributed sensors and actuators which are collecated, and the wide distribution of landing modes that must be reduced from a dimensional standpoint.

Morais, B. G.↗
NASA NTRS1986

Electrochemical carbon dioxide concentrator subsystem development

The most promising concept for a regenerative CO2 removal system for long duration manned space flight is the Electrochemical CO2 Concentrator (EDC), which allows for the continuous, efficient removal of CO2 from the spacecraft cabin. This study addresses the advancement of the EDC system by generating subsystem and ancillary component reliability data through extensive endurance testing and developing related hardware components such as electrochemical module lightweight end plates, electrochemical module improved isolation valves, an improved air/liquid heat exchanger and a triple redundant relative humidity sensor. Efforts included fabrication and testing the EDC with a Sabatier CO2 Reduction Reactor and generation of data necessary for integration of the EDC into a space station air revitalization system. The results verified the high level of performance, reliability and durability of the EDC subsystem and ancillary hardware, verified the high efficiency of the Sabatier CO2 Reduction Reactor, and increased the overall EDC technology engineering data base. The study concluded that the EDC system is approaching the hardware maturity levels required for space station deployment.

Koszenski, E. P.↗
NASA NTRS1992

The ACTS multibeam antenna

The Advanced Communications Technology Satellite (ACTS) to be launched in 1993 introduces several new technologies including a multibeam antenna (MBA) operating at Ka-band. The satellite is introduced briefly, and then the MBA, consisting of electrically similar 30 GHz received and 20 GHz transmit offset Cassegrain systems utilizing orthogonal linear polarizations, is described. Dual polarization is achieved by using one feed assembly for each polarization in conjunction with nested front and back subreflectors, the gridded front subreflector acting as a window for one polarization and a reflector for the other. The antennas produce spot beams with approximately 0.3 deg beamwidth and gains of approximately 50 dbi. High surface accuracy and high edge taper produce low sidelobe levels and high cross-polarization isolation. A brief description is given of several Ka-band components fabricated for ACTS. These include multiflare antenna feedhorns, beam-forming networks utilizing latching ferrite waveguide switches, a 30 GHz high mobility electron transmitter (HEMT) low-noise amplifier and a 20 GHz TWT power amplifier.

Regier, Frank A.↗
NASA NTRS1992

The ACTS multibeam antenna

The Advanced Communications Technology Satellite (ACTS) to be launched in 1993 is briefly introduced. Its multibeam antenna, consisting of electrically similar 30 GHz receive and 20 GHz transmit offset Cassegrain systems, both utilizing orthogonal polarizations, is described. Dual polarization is achieved by using one feed assembly for each polarization in conjunction with nested front and back subreflectors, the gridded front subreflector acting as a window for one polarization and a reflector for the other. The antennas produce spot beams with approximately 0.3 degree beamwidth and gains of approximately 50 dbi. High surface accuracy and high edge taper produce low sidelobe levels and high cross-polarization isolation. A brief description is given of several Ka-band components fabricated for ACTS. These include multiflare antenna feedhorns, beam-forming networks utilizing latching ferrite waveguide switches, a 30 GHz HEMT low-noise amplifier and a 20 GHz TWT power amplifier.

Regier, Frank A.↗
NASA NTRS1998

A Geometry Based Infra-Structure for Computational Analysis and Design

The computational steps traditionally taken for most engineering analysis suites (computational fluid dynamics (CFD), structural analysis, heat transfer and etc.) are: (1) Surface Generation -- usually by employing a Computer Assisted Design (CAD) system; (2) Grid Generation -- preparing the volume for the simulation; (3) Flow Solver -- producing the results at the specified operational point; (4) Post-processing Visualization -- interactively attempting to understand the results. For structural analysis, integrated systems can be obtained from a number of commercial vendors. These vendors couple directly to a number of CAD systems and are executed from within the CAD Graphical User Interface (GUI). It should be noted that the structural analysis problem is more tractable than CFD; there are fewer mesh topologies used and the grids are not as fine (this problem space does not have the length scaling issues of fluids). For CFD, these steps have worked well in the past for simple steady-state simulations at the expense of much user interaction. The data was transmitted between phases via files. In most cases, the output from a CAD system could go to Initial Graphics Exchange Specification (IGES) or Standard Exchange Program (STEP) files. The output from Grid Generators and Solvers do not really have standards though there are a couple of file formats that can be used for a subset of the gridding (i.e. PLOT3D data formats). The user would have to patch up the data or translate from one format to another to move to the next step. Sometimes this could take days. Specifically the problems with this procedure are:(1) File based -- Information flows from one step to the next via data files with formats specified for that procedure. File standards, when they exist, are wholly inadequate. For example, geometry from CAD systems (transmitted via IGES files) is defined as disjoint surfaces and curves (as well as masses of other information of no interest for the Grid Generator). This is particularly onerous for modern CAD systems based on solid modeling. The part was a proper solid and in the translation to IGES has lost this important characteristic. STEP is another standard for CAD data that exists and supports the concept of a solid. The problem with STEP is that a solid modeling geometry kernel is required to query and manipulate the data within this type of file. (2) 'Good' Geometry. A bottleneck in getting results from a solver is the construction of proper geometry to be fed to the grid generator. With 'good' geometry a grid can be constructed in tens of minutes (even with a complex configuration) using unstructured techniques. Adroit multi-block methods are not far behind. This means that a million node steady-state solution can be computed on the order of hours (using current high performance computers) starting from this 'good' geometry. Unfortunately, the geometry usually transmitted from the CAD system is not 'good' in the grid generator sense. The grid generator needs smooth closed solid geometry. It can take a week (or more) of interaction with the CAD output (sometimes by hand) before the process can begin. One way Communication. (3) One-way Communication -- All information travels on from one phase to the next. This makes procedures like node adaptation difficult when attempting to add or move nodes that sit on bounding surfaces (when the actual surface data has been lost after the grid generation phase). Until this process can be automated, more complex problems such as multi-disciplinary analysis or using the above procedure for design becomes prohibitive. There is also no way to easily deal with this system in a modular manner. One can only replace the grid generator, for example, if the software reads and writes the same files. Instead of the serial approach to analysis as described above, CAPRI takes a geometry centric approach. This makes the actual geometry (not a discretized version) accessible to all phases of the analysis. The connection to the geometry is made through an Application Programming Interface (API) and NOT a file system. This API isolates the top-level applications (grid generators, solvers and visualization components) from the geometry engine. Also this allows the replacement of one geometry kernel with another, without effecting these top-level applications. For example, if UniGraphics is used as the CAD package then Parasolid (UG's own geometry engine) can be used for all geometric queries so that no solid geometry information is lost in a translation. This is much better than STEP because when the data is queried, the same software is executed as used in the CAD system. Therefore, one analyzes the exact part that is in the CAD system. CAPRI uses the same idea as the commercial structural analysis codes but does not specify control. Software components of the CAD system are used, but the analysis suite, not the CAD operator, specifies the control of the software session. This also means that the license issues (may be) minimized and individuals need not have to know how to operate a CAD system in order to run the suite.

Haimes, Robert↗