Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “carbon defects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

20-kV GaN Switch Technology Demonstrated in High-Efficiency Medium-Voltage Power Module

GaN holds significant potential as a material for vertical p-n diodes, enabling the realization of devices with reverse breakdown voltages of 5 kV or higher. Carbon serves as the primary compensating dopant in the growth process, incorporated into GaN during metalorganic chemical vapor deposition (MOCVD) growth. The level of carbon incorporation depends on several factors, including growth rate, ammonia flow, temperature, pressure, and trimethylgallium (TMGa) flow. Through guided empirical modeling, the carbon incorporation in GaN growth could be predicted using a single parameter based on the ratio of ammonia flow to the growth rate. This model accurately predicts carbon concentrations ranging from 1x10 17 to 5x10 14 cm -3 while maximizing growth rates. Other extrinsic dopants have either been reduced below the threshold of consideration or modeled using similar single-parameter relationships. By identifying the dominant extrinsic dopants and accounting for them, an intrinsic defect with a concentration of 2.2x10 15 cm -3 was identified. By combining these relationships, growth conditions for n-GaN were optimized, resulting in electron concentrations as low as 1x10 15 cm -3 . Leveraging these techniques, p-n diodes were grown, achieving a reverse breakdown voltage as high as 3.1 kV.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Durability Issues for the Protection of Materials from Atomic Oxygen Attack in Low Earth Orbit

Low Earth orbital atomic oxygen is capable of eroding most polymeric materials typically used on spacecraft. Solar array blankets, thermal control polymers, and carbon fiber matrix composites are readily oxidized to become thinner and less capable of supporting the loads imposed upon them. Protective coatings have been developed that are durable to atomic oxygen to prevent oxidative erosion of the underlying polymers. However, the details of the surface roughness, coating defect density, and coating configuration can play a significant role as to whether or not the coating provides long duration atomic oxygen protection. Identical coatings on different surface roughness surfaces can have drastically different durability results. Examples and analysis of the causes of resultant differences in atomic oxygen protection are presented. Implications based on in-space experiences, ground laboratory testing, and computational modeling indicate that thin film vacuum-deposited aluminum protective coatings offer much less atomic oxygen protection than sputter-deposited silicon dioxide coatings.

Banks, Bruce↗
NASA NTRSDate not supplied

NDE Methods and Capabilities Handbook – Resources for the Composites NDE Community

Composite structures are often difficult to inspect due to the anisotropic nature of the material systems and the range of flaws and defects that can arise in the manufacturing process. NASA’s Advanced Composites Project, a public-private partnership between government, universities and industry, sought to address improved methods, tools, and protocols to reduce the development and certification timeline for composite materials and structures. The rapid inspection of composites was one of the three focused research areas of the project. One deliverable of the project was to develop an NDE Methods and Capabilities Handbook. This Handbook provides a publicly available guidance document that facilitates the selection of appropriate NDE techniques and provides recommended protocols for detecting and characterizing common flaw types in solid laminate carbon fiber reinforced polymer composite (CFRP) structures. The Handbook seeks to reduce the time required to develop qualified inspection processes for composite aircraft structures during the development, certification, and manufacturing phases by providing a reference that helps minimize trial and error and provides guidance on best practices, techniques, and settings, for specific flaw types and geometries. NDE techniques include, but are not limited to ultrasound, laser based ultrasound, infrared thermography, and x-ray CT. Flaw types include, but are not limited to porosity, delamination, voids, AFP defects and impact damage. The Handbook contains details such as inspection parameters, data analysis techniques, inspection efficiency (speed & cost), and limitations. This presentation will describe key Handbook activities with examples of the techniques and flaw types examined by the Advanced Composite Consortium members. Availability of the fabricated NDE standards as well as the raw data collected on the standards by the Consortium members to the NDE community is discussed.

Patricia A Howell↗
DOE OSTI2024

First-Principles Calculations of the Electrical Conductivity of Carbon Nanotubes Functionalized with Copper and Nitrogen: Implications for Electronics, Energy Storage, and Nanodevices

In this work, we investigate the electrical conductivity of carbon nanotubes (CNTs), with a particular focus on the effects of doping. Using first-principles-based approaches, we study the electronic structure, phonon dispersion, and electron–phonon scattering to understand the finite-temperature electrical transport properties in CNTs. Our study covers both prototypical metallic and semiconducting CNTs, with special emphasis on the influence of typical defects such as vacancies and the incorporation of copper or nitrogen, such as pyridinic N, pyrrolic N, graphitic N, and oxidized N. Our theoretical study shows significant improvements in the electrical conduction properties of copper-CNT composites, especially when semiconducting CNTs are functionalized with nitrogen. Doping is found to cause significant changes in the electronic density of states near the Fermi level, which affects the electrical conductivity. Calculations show that certain types of functional groups, such as N-pyrrolic, result in more than 30-fold increase in the conductivity of semiconducting CNTs compared to Cu-incorporated CNTs alone. For metallic CNTs, the conductivity is in agreement with existing experimental data, and our prediction of significant increases in conductivity with N-pyrrolic functional group is consistent with recent experimental results, demonstrating the effectiveness of doping in modifying conductivity. In conclusion, our study provides valuable insight into the electronic properties of doped CNTs and contributes to the development of ultrahigh conductivity CNT composites.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

NDE Methods and Capabilities Handbook - Resources for the Composites NDE Community

Composite structures are often difficult to inspect due to the anisotropic nature of the material systems and the range of flaws and defects that can arise in the manufacturing process. NASA’s Advanced Composites Project, a public-private partnership between government, universities and industry, sought to address improved methods, tools, and protocols to reduce the development and certification timeline for composite materials and structures. The rapid inspection of composites was one of the three focused research areas of the project. One deliverable of the project was to develop an NDE Methods and Capabilities Handbook. This Handbook provides a publicly available guidance document that facilitates the selection of appropriate NDE techniques and provides recommended protocols for detecting and characterizing common flaw types in solid laminate carbon fiber reinforced polymer composite (CFRP) structures. The Handbook seeks to reduce the time required to develop qualified inspection processes for composite aircraft structures during the development, certification, and manufacturing phases by providing a reference that helps minimize trial and error and provides guidance on best practices, techniques, and settings, for specific flaw types and geometries. Techniques include, but are not limited to ultrasound, laser based ultrasound, infrared thermography, and x-ray CT. Flaw types include, but are not limited to porosity, delaminations, voids, Automated Fiber Placement (AFP) defects and impact damage. The Handbook contains details such as inspection parameters, data analysis techniques, inspection efficiency and limitations. This presentation will describe key Handbook activities with examples of the techniques and flaw types examined by the Advanced Composite Consortium members. Availability to the NDE community of the fabricated NDE standards as well as the raw data collected on the standards by the Consortium members is discussed.

Nondestructive Evaluation↗
NASA NTRSDate not supplied

NDE Methods and Capabilities Handbook - Resources for the Composites NDE Community

Composite structures are often difficult to inspect due to the anisotropic nature of the material systems and the range of flaws and defects that can arise in the manufacturing process. NASA’s Advanced Composites Project, a public-private partnership between government, universities and industry, sought to address improved methods, tools, and protocols to reduce the development and certification timeline for composite materials and structures. The rapid inspection of composites was one of the three focused research areas of the project. One deliverable of the project was to develop an NDE Methods and Capabilities Handbook. This Handbook provides a publicly available guidance document that facilitates the selection of appropriate NDE techniques and provides recommended protocols for detecting and characterizing common flaw types in solid laminate carbon fiber reinforced polymer composite (CFRP) structures. The Handbook seeks to reduce the time required to develop qualified inspection processes for composite aircraft structures during the development, certification, and manufacturing phases by providing a reference that helps minimize trial and error and provides guidance on best practices, techniques, and settings, for specific flaw types and geometries. Techniques include, but are not limited to ultrasound, laser based ultrasound, infrared thermography, and x-ray CT. Flaw types include, but are not limited to porosity, delaminations, voids, Automated Fiber Placement (AFP) defects and impact damage. The Handbook contains details such as inspection parameters, data analysis techniques, inspection efficiency and limitations. This paper describes key Handbook activities with examples of the techniques and flaw types examined by the Advanced Composite Consortium members. Availability to the NDE community of the fabricated NDE standards as well as the raw data collected on the standards by the Consortium members is discussed.

nondestructive evaluation↗
DOE OSTI2020

Microstructural evolution of a silicon carbide-carbon coated nanostructured ferritic alloy composite during in-situ Kr ion irradiation at 300°C 450°C

This work focuses on irradiation behaviors of a novel silicon carbide and carbon coated nanostructured ferritic alloy (SiC-C@NFA) composite for potential applications as a cladding and structural material for next generation nuclear reactors. The SiC-C@NFA samples were irradiated with 1 MeV Kr ions up to 10 dpa at 300 and 450 °C. Microstructures and defect evolution were studied in-situ at the IVEM-Tandem facility at Argonne National Laboratory. The effects of ion irradiation on various phases such as α-ferrite matrix, (Fe,Cr) 7 C 3 , and (Ti,W)C precipitates were evaluated. The α-ferrite matrix showed a continuous increase in dislocation density along with spatial ordering of dislocation loops (or loop strings) at >5 dpa. The size of the dislocation loops at 450 °C was larger than that at 300 °C. The nucleation and growth of new (Ti,W)C precipitates in α-ferrite grains were enhanced with the ion dose at 450 °C. This study provides new insight into the irradiation resistance of the SiC-C@NFA system.

(FeCr)(7)C-3↗
DOE OSTI2025

Synthesizing intermetallic thermoelectric materials using metal flux growth method

With zero energy poverty by 2050 goals, exploring innovative energy technologies is essential. Thermoelectric materials (TEMs) have the potential to harness waste heat and convert it to electricity (e.g., for spacecraft power, sensors, and cryogenic cooling). Two limitations of thermoelectric compounds are their low efficiency and limited pool of materials. Optimizing the efficiency of TEMs is challenging due to the interdependent relationship between electrical and thermal conductivity. A deeper understanding of electronic properties and lattice thermal conductivity is necessary to “understand, predict and ultimately control” the thermoelectric properties of TEMs. Understanding the influence of light-atom-doping and intrinsic defects on the electronic properties of the f-element containing TEMs are important questions that need to be answered to design and synthesize TEMs with optimal parameters. The purpose of this work is to understand how doping f-element based TEMs with light elements, such as carbon and boron, would impact the crystal structure, bond lengths, band gaps, and thermoelectric characteristics. High-quality f¬-element containing intermetallic single crystals are grown in metal flux media. In molten metal flux growth method, one or more low-melting metals such as aluminum, gallium, tin, and bismuth are used in excess as the reaction medium. As these are solution-state reactions, we can use lower temperatures than solid-state reactions and isolate the kinetic products instead of the thermodynamically stable compound. Then these are characterized using X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, magnetization, electrical and thermal conductivities, and thermoelectric power.

37 - INORGANIC, ORGANIC, PHYSICAL AND ANALYTICAL C↗
DOE OSTI2025

Bio‐Inspired Cascade Photocatalysis on Fe Single‐Atom Carbon Nitride Upcycles Plastic Wastes for Effective Acetic Acid Production

Plastic imposes a critical threat to the environment, ecosystems, and human health because of the low utilization efficiency of plastics. Here, we demonstrate a sustainable, highly efficient cascade photocatalysis for upcycle plastics to value-added acetic acid using Fe single-atom catalysts (Fe@C 3 N 4 SAC) at ambient conditions. Inspired by Phanerochaete chrysosporium microbial, the defective Fe@C 3 N 4 SAC acts as a bifunctional cascade photocatalyst for both Fenton-like and CO 2 reduction reactions. During the reaction, hydroxyl radicals (*OH) form and subsequently oxidize plastics into CO 2 intermediates. These CO 2 intermediates are then photo-reduced to CH 3 COOH on the same catalyst via cascade photocatalysis. The mechanism is confirmed by in situ multimodal microscopy and spectroscopies, with density functional theory calculations. A state-of-art CH 3 COOH yield of 63.8 mg h −1 gcat −1 from PVC, 12.7 mg h −1 gcat −1 from PE, 5.4 mg h −1 gcat −1 from PET, and 5.3 mg h −1 gcat −1 from PP are directly obtained under AM1.5G solar irradiation and further validated under real sunlight (≈0.6 sun), achieving 5.6 mg h −1 gcat −1 from PET, using low-cost Fe@C 3 N 4 SAC in a sealed reactor by enhancing the photon transport and utilization efficiency. The techno-economic analysis shows it is promising to practically mitigate plastic based on broader social welfare assessments.

cascade photocatalysis↗
DOE OSTI2021

Photocurrent in carbon nanotube bundle: Graded Seebeck coefficient phenomenon

Here, polarized photovoltage of a suspended aligned carbon nanotube (CNT) bundle under uniform optical irradiation is discovered without additional structural modification or bias voltage. Such a phenomenon is very surprising considering the metallic behavior of the overall bundle and zero temperature difference between ends. The photovoltage characteristic time is found similar to the thermal response time under step Joule heating and implies a relation to the thermal behavior of the CNT bundle. A similar thermoelectric voltage is also observed during step Joule heating. Localized laser heating and scanning along the axial direction of the bundle uncovers a linear spatial variation of the local Seebeck coefficient. The Seebeck coefficient linearly decreases from root to tip of the CNT bundle with a rate of a few - µV∙K –1 ·mm –1 . Deep investigation in both the microscopic and macroscopic structures of the CNT bundle reveals that the local alignment of CNT assemblies rather than the minor defects in individual CNTs brings about this linear distribution of Seebeck coefficient in space. The finding presents a new way for direct photon-to-electric energy conversion via Seebeck coefficient grading in CNT structures.

42 ENGINEERING↗
DOE OSTI2023

Lignin-based carbon quantum dots with high fluorescence performance prepared by supercritical catalysis and solvothermal treatment for tumor-targeted labeling

The poor fluorescence performance of lignin-based carbon quantum dots (L-CQDs) prepared using the bottom-up method has hindered their development. Here, in this study, a two-step strategy was proposed to efficiently enhance the fluorescence properties of L-CQDs. Lignin was first cracked using an ethanol supercritical/noble metal catalyst; then, the L-CQDs were prepared with the cracked lignin fragments as carbon precursors without adding any modified reagents. Compared with the OL-CQDs prepared by the traditional one-pot hydrothermal method, the L-CQDs-1 prepared from CL-1 containing much low molecular weight compounds, and have photoluminescence (increased from 63 to 975) and excellent up-conversion photoluminescence (enhanced by 16.3 to 963), which significantly enhanced by about 15 times and 60 times, respectively. They can emit bright blue fluorescence under both ultraviolet and near-infrared light irradiation owing to a large amount of surface defects caused by the rich compound composition. When L-CQDs-1 were combined with, and quenched by folic acid (FA), the prepared FA@L-CQDs-1 show the ability to target and label tumor cells. This study opens new avenues for the preparation of L-CQDs with high fluorescence performance using lignocellulosic material without heteroatom additives.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS2004

Growth of Multi-Walled Carbon Nanotubes by Injection CVD Using Cyclopentadienyliron Dicarbonyl Dimer and Cyclooctatetraene Iron Tricarbonyl

Preferential oriented multiwalled carbon nanotubes were prepared by the injection chemical vapor deposition (CVD) method using either cyclopentadienyliron dicarbonyl dimer or cycloctatetraene iron tricarbonyl as the iron catalyst source. The catalyst precursors were dissolved in toluene as the carrier solvent for the injections. The concentration of the catalyst was found to influence both the growth of the nanotubes as well as the amount of iron in the deposited material. As deposited the multiwalled carbon nanotubes contained as little as 2.8% iron by weight. The material was deposited onto tantalum foil and fused silica substrates. The nanotubes were characterized by scanning electron microscopy, transmission electron microscopy, Raman spectroscopy and thermogravimetric analysis. This synthetic route provides a simple and scalable method to deposit MWNTs with a low defect density, low metal content and preferred orientation.

Harris, Jerry D.↗
NASA NTRS2009

From Bench Top to Market: Growth of Multi-Walled Carbon Nanotubes by Injection CVD Using Fe Organometallics - Production of a Commercial Reactor

Preferential oriented multiwalled carbon nanotubes were prepared by the injection chemical vapor deposition (CVD) method using either cyclopentadienyliron dicarbonyl dimer or cyclooctatetraene iron tricarbonyl as the iron catalyst source. The catalyst precursors were dissolved in toluene as the carrier solvent for the injections. The concentration of the catalyst was found to influence both the growth (i.e., MWNT orientation) of the nanotubes, as well as the amount of iron in the deposited material. As deposited, the multiwalled carbon nanotubes contained as little as 2.8% iron by weight. The material was deposited onto tantalum foil and fused silica substrates. The nanotubes were characterized by scanning electron microscopy, transmission electron microscopy, Raman spectroscopy and thermogravimetric analysis. This synthetic route provides a simple and scalable method to deposit MWNTs with a low defect density, low metal content and a preferred orientation. Subsequently, a small start-up was founded to commercialize the deposition equipment. The contrast between the research and entrepreneurial environments will be discussed.

Rowsell, J.↗
DOE OSTI2024

Characteristics of graphene oxide-like materials prepared from different deashed-devolatilized coal chars and comparison with graphite-based graphene oxide, with or without the ultrasonication treatment

Deashed-devolatilized coal chars were prepared from anthracite, bituminous, subbituminous, and lignite coals, then oxidized to prepare graphene oxide (GO)-like materials that were extensively characterized and compared with a pristine graphite-based GO sample (CGO). Coal-based GO-like materials and CGO were then subjected to ultrasonication treatment for delamination, which also impacted their physicochemical properties. The surface oxygen contents of CGO and coal-based samples were ~32 % and ~26–35 %, respectively, that were reduced to ~27 % and ~21–24 %, respectively, after ultrasonication. The Fourier transform infrared and X-ray photoelectron spectroscopy spectra of all samples showed different profiles before and after the ultrasonication, suggesting a change in chemical functionalities. The Raman spectra of CGO and coal-based samples exhibited similar D and G bands with D/G intensity ratios (I D /I G ) of 0.93 and 0.88–0.92, respectively. The I D /I G ratio of CGO and most of the coal-based samples increased after the ultrasonication due to creation of more defects. The main X-ray diffraction (XRD) peak for CGO and coal-based samples were observed at ~11° and ~22–24°, respectively. Ultrasonication of the samples resulted in a reduction of crystallite size and number of layers for all CGO and coal-based samples, confirming both splitting and delamination of carbon layers. Additionally, different coal-based samples exhibited almost overlapping XRD profiles after the ultrasonication.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Plasma-assisted atomic layer etching of single-crystal diamond

Applications of near-surface nitrogen-vacancy (NV) centers in diamond are often limited by surface defects created during processing. Understanding and controlling plasma-induced surface damage is important for preserving the optical and spin properties of diamond NV centers. We report molecular dynamics simulations of a novel form of plasma-aided atomic layer etching of diamond. In this proposed scheme, the initial surface modification step consists of Ar + ion bombardment. This creates an amorphous layer at the surface, the thickness of which is controlled by the ion energy. Amorphization is known to help smooth the surface, at least locally, and would also serve to sputter clean an initially contaminated surface. A second step impacts the amorphous carbon layer with O + between about 1 and 5 eV. Simulations show that this energy range will remove the amorphous carbon but will not etch the underlying diamond. Though this energy range is not trivial to achieve in a conventional low-temperature plasma, potential methods for creating these low-energy O + ions are discussed. In addition to a-C etching, the O + impacts are predicted to remove any isolated (100) diamond terraces by selectively attacking the edges of the terraces. The proposed atomic layer etching (ALE) approach reverses the conventional ALE sequence in which the surface modification step is usually chemical modification (oxidation in this case), followed by a removal step using Ar + impacts. This plasma ALE procedure is predicted to create a diamond surface that is atomically flat and defect free.

Draney, J. S. [Princeton University, NJ (United St↗
DOE OSTI2021

Thin-film composite membranes based on hyperbranched poly(ethylene oxide) for CO 2 /N 2 separation

Cross-linked amorphous poly(ethylene oxide) (XLPEO) is one of the leading membrane materials for post-combustion CO 2 capture. For example, XLPEO prepared from poly(ethylene glycol) methyl ether acrylate (PEGMEA) exhibited CO 2 permeability of 570 Barrer and CO 2 /N 2 selectivity of 41 at 35 °C. However, these XLPEOs cannot be dissolved in coating solutions, making it impossible to be fabricated into thin-film composite (TFC) membranes using state-of-the-art manufacturing processes. In this study, we synthesized high molecular weight yet soluble HPEO via atom transfer radical polymerization (ATRP). These polymers were thoroughly characterized and compared with XLPEO, including thermal transitions, free volumes, and pure-gas sorption and permeation properties. A polymer with the best combination of CO 2 permeability (540 Barrer) and CO 2 /N 2 selectivity (43) was fabricated into defect-free TFC membranes with a thickness as thin as 506 ± 44 nm. When challenged with simulated flue gas containing water vapor at 35 °C for over 100 h, the membrane shows stable CO 2 permeance of 850 GPU and CO 2 /N 2 selectivity of 37, comparable to the leading commercial membranes for carbon capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1998

Carboxylic and Dicarboxylic Acids Extracted from Crushed Magnesium Oxide Single Crystals

Carboxylic and dicarboxylic acids (glycolic, oxalic, malonic and succinic) have been extracted with tetrahydrofuran (THE) and H2O from large synthetic MgO crystals, crushed to a medium fine powder. The extracts were characterized by infrared spectroscopy and (sup 1)H-NMR (Nuclear Magnetic Resonance). The THF extracts were derivatized with tert-butyldimethylsilyl (t-BDMS) for GC-MS (Gas Chromatography - Mass Spectroscopy) analysis. A single crystal separated from the extract was used for an x-ray structure analysis, giving the monoclinic unit cell, space group P2(sub 1)/c with a(sub o) = 5.543 A, b(sub o) = 8.845 A, c(sub o) = 5.086 A, and beta = 91.9 degrees, consistent with beta-succinic acid, HOOC(CH2)COOH. The amount of extracted acids is estimated to be of the order of 0.1 to 0.5 mg/g MgO. The MgO crystals from which these organic acids were extracted grew from the 2360 C hot melt, saturated with CO/CO2 and H2O, thereby incorporating small amounts of the gaseous components to form a solid solution (ss) with MgO. Upon cooling, the ss becomes supersaturated, causing solute carbon and other solute species to segregate not only to the surface but also internally, to dislocations and subgrain boundaries. The organic acids extracted from the MgO crystals after crushing appear to derive from these segregated solutes that formed C-C, C-H, and C-O bonds along dislocations and other defects in the MgO structure, leading to entities that can generically be described as (HxCyOz)(sup n-). The processes underlying the formation of these precursors are fundamental in nature and expected to be operational in any minerals, preferentially those with dense structures, that crystallized in H2O-CO2-laden environments. This opens the possibility that common magmatic and metamorphic rocks when weathering at the surface of a tectonically active planet like Earth may be an important source of abiogenically formed complex organic compounds.

Freund, Friedemann↗
NASA NTRS1999

Carboxylic and dicarboxylic acids extracted from crushed magnesium oxide single crystals

Carboxylic and dicarboxylic acids (glycolic, oxalic, malonic and succinic) have been extracted with tetrahydrofuran (THF) and H2O from large synthetic MgO crystals, crushed to a medium fine powder. The extracts were characterized by infrared spectroscopy and 1H-NMR. The THF extracts were derivatized with tert-butyldimethylsilyl (t-BDMS) for GC-MS analysis. A single crystal separated from the extract was used for an x-ray structure analysis, giving the monoclinic unit cell, space group P21/c with ao = 5.543 A, bo = 8.845 A, co = 5.086 A, and beta = 91.9 degrees, consistent with beta-succinic acid, HOOC(CH2)COOH. The amount of extracted acids is estimated to be of the order of 0.1 to 0.5 mg g-1 MgO. The MgO crystals from which these organic acids were extracted grew from the 2860 degrees C hot melt, saturated with CO/CO2 and H2O, thereby incorporating small amounts of the gaseous components to form a solid solution (ss) with MgO. Upon cooling, the ss becomes supersaturated, causing solute carbon and other solute species to segregate not only to the surface but also internally, to dislocations and subgrain boundaries. The organic acids extracted from the MgO crystals after crushing appear to derive from these segregated solutes that formed C-C, C-H and C-O bonds along dislocations and other defects in the MgO structure, leading to entities that can generically be described as (HxCyOz)n-. The processes underlying the formation of these precursors are fundamental in nature and expected to be operational in any minerals, preferentially those with dense structures, that crystallized in H2O-CO2-laden environments. This opens the possibility that common magmatic and metamorphic rocks when weathering at the surface of a tectonically active planet like Earth may be an important source of abiogenically formed complex organic compounds.

NASA Discipline Exobiology↗