Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “atomic volume”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Comparison of Non-Combusting Spray Fields in a Model Combustor using Shadowgraphy

Droplet sizes were measured using shadowgraphy in the spray issuing from the center element of the baseline configuration of the NASA 7-element lean direct injector (LDI) array. Each LDI element consisted of a 60 degree clockwise axial air swirler, converging-diverging venturi, and a pressure-swirl atomizer positioned with its tip at the venturi throat. The non-combusting measurements were conducted using water spray in a 3-inch diameter research combustor operating at pressure of 5 bar and air inlet temperature of 700 K. At these inlet conditions, three air flow rates were used, producing reference velocities of 7.6, 15.2, and 22.9 m/s. Only the center nozzle was used. At each reference velocity, water flow rates were adjusted to simulate a common equivalence. Data were collected at a frame rate of 15 Hz over a range of positions near the LDI dump plane, and downstream, along the combustor centerline. Velocity measurements were achieved by use of a dual head Nd:YAG laser and frame transfer PIV camera. Droplet size and velocity, mass and number density, and volume fraction are compared at these inlet conditions to determine the effect of nozzle pressure drop on the measured properties.

lean direct injection↗
DOE OSTI2020

High-volume and -adiabat capsule (“HVAC”) ignition: Lowered fuel compression requirements using advanced Hohlraums

Lower-than-expected deuterium–tritium fuel areal densities have been experimentally inferred across a variety of high-convergence, nominally low-adiabat implosion campaigns at the National Ignition Facility (NIF) using cylinder-shaped Hohlraums [Hurricane et al., Phys. Plasmas 26, 052704 (2019)]. A leading candidate explanation is the presence of atomic mix between the fuel and ablator from hydrodynamic instability growth [Clark et al., Phys. Plasmas 26, 050601 (2019)], leading to reduced fuel compressibility and an effectively higher (in-flight) fuel adiabat α. Tolerating a high-α implosion can be obtained with significantly higher capsule absorbed energy Ecap according to the one-dimensional (1-D) ignition-threshold-factor analytic scaling [S. Atzeni and J. Meyer-ter-Vehn, Nucl. Fusion 41, 465 (2001)], ITF∼Ecap·α−1.8. Recent experiments with large Al shells in rugby-shaped Hohlraums have established high laser-capsule coupling efficiencies of ≽ 30% [Ping et al., Nat. Phys. 15, 138 (2019)], enabling a path to Ecap≽ 0.5 MJ at the NIF and increased performance margin M ≡ ITF − 1. The ability to operate at high adiabat with large capsules using nonstandard Hohlraums leads to the predicted onset of a volume-ignition mode, defined as when both the entire fuel is the “hot spot” and inertial confinement is principally provided by the ablator compared with the compressed fuel. Such an ignition mode, normally reserved for high-Z targets, e.g., double shells [Amendt et al., Phys. Plasmas 14, 056312 (2007)], is predicted to lead to lower fuel convergence and less exposure to mix due to the intended high adiabat—but at the expense of ∼3–4 × reduced (1-D) yield compared with conventional central hot-spot ignition designs.

Amendt, Peter (ORCID:0000000174021777)↗
NASA NTRS1972

Physics in perspective. Volume 2, part A: The core subfields of physics

Panel reports to the Survey Committee are presented to provide detailed technical background and documentation for committee findings, and to indicate the vitality and strength of the subfields of physics. Included are the core subfields of acoustics, optics, condensed matter, plasmas and fluids, atomic molecular and electron physics, nuclear physics, and elementary particle physics.

Source record↗
NASA NTRS1986

Characterization of simulated small-droplet fuel sprays

A two-fluid pneumatic atomizer operating at relatively high liquid and gas pressures produced water sprays that simulated small-droplet clouds of liquid fuel for use in studying vaporization and fuel-air mixing effects on combustor performance and emissions. To characterize the sprays, a scattered-light scanning instrument was developed and measurements of volume median or volume mean diameter, D sub V.5, were correlated with D sub O, W sub w, and W sub n, i.e., orifice diameter, water, and nitrogen gas flow rates, respectively, to give the general expression: D sub v.5 approx. (D sub o sup 0.2) (W sub w sup m) (W sub n sup n), which yields D sub v.5 = 45 (D sub o sup 0.2) (W sub w sup 0.2) (W sub w sup - 1.2). Values of D sub o, W sub w, and W sub n are in centimeters and grams/second, respectively. Farther downstream at an axial distance of 6.7 cm, exponent m increased from 0.2 to 0.4 and exponent n decreased from -1.2 to -1.0 and at a distance of 25 cm downstream of the atomizer, n decreased to -0.8. The increase in exponent m and decrease in exponent n was attributed to a loss of very small droplets from the spray due primarily to vaporization and diffusion effects on clouds of small droplets traveling a distance of 25 cm.

Ingebo, R. D.↗
NASA NTRS1986

Characterization of simulated small-droplet fuel sprays

A two-fluid pneumatic atomizer operating at relatively high liquid and gas pressures produced water sprays that simulated small-droplet clouds of liquid fuel for use in studying vaporization and fuel-air mixing effects on combustor performance and emissions. To characterize the sprays, a scattered-light scanning instrument was developed and measurements of volume median or volume mean diameter, D sub V.5, were correlated with D sub O, W sub w, and W sub n, i.e., orifice diameter, water, and nitrogen gas flow rates, respectively, to give the general expression: D sub v.5 approx. (D sub O sup 0.2) (W sub w sup m) (W sub n sup n), which yields D sub v.5 = 45 (D sub o sup 0.2) (W sub w sup 0.2) (W sub w sup -1.2). Values of D sub 0, W sub w, and W sub n are in centimeters and grams/second, respectively. Farther downstream at an axial distance of 6.7 cm, exponent m increased from 0.2 to 0.4 and exponent n decreased from -1.2 to -1.0 and at a distance of 25 cm downstream of the atomizer, n decreased to -0.8. The increase in exponent m and decrease in exponent n was attributed to a loss of very small droplets from the spray due primarily to vaporization and diffusion effects on clouds of small droplets traveling a distance of 25 cm.

Ingebo, R. D.↗
DOE OSTI2024

Dynamics of High Molecular Weight Cylindrical and Lamellar Block Copolymers with X‐ray Photon Correlation Spectroscopy

Here, the structure and dynamics of polystyrene (PS)-b-poly(ethylene oxide) block copolymers (BCPs) are studied. The BCPs exhibit microphase-separated cylindrical and lamellar morphologies. Structural dynamics are measured with X-ray photon correlation spectroscopy in the small-angle regime. Morphologies and domain sizes are evaluated using small-angle X-ray scattering (SAXS), scanning electron microscopy, and atomic force microscopy. Different solvent processing conditions are investigated. Grain sizes evaluated using SAXS are found to depend on processing only for the rubbery majority BCP. The structural relaxation times are examined as a function of PS volume fraction, temperature, morphology, and structural sizes. Well above the glass transition temperature (T g ) of PS, all samples exhibit stretched autocorrelation decays and diffusive dynamics. Near T g of PS, the dynamics of all samples are anomalous with compressed autocorrelation decays and hyperdiffusive dynamics. This transition occurs at 153 °C or 1.13 T g of PS. In the diffusive regime (at high temperature), structural relaxation times are dependent on the processing method. Near PS T g (at low temperature), structural relaxation times scale with the PS volume fraction. Structural relaxation times do not correlate with grain size, indicating that the out-of-equilibrium state of PS dominates the structural dynamics of these strongly phase-segregated BCPs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Autonomous scanning probe microscopy investigations over WS2 and Au{111}

Abstract Individual atomic defects in 2D materials impact their macroscopic functionality. Correlating the interplay is challenging, however, intelligent hyperspectral scanning tunneling spectroscopy (STS) mapping provides a feasible solution to this technically difficult and time consuming problem. Here, dense spectroscopic volume is collected autonomously via Gaussian process regression, where convolutional neural networks are used in tandem for spectral identification. Acquired data enable defect segmentation, and a workflow is provided for machine-driven decision making during experimentation with capability for user customization. We provide a means towards autonomous experimentation for the benefit of both enhanced reproducibility and user-accessibility. Hyperspectral investigations on WS 2 sulfur vacancy sites are explored, which is combined with local density of states confirmation on the Au{111} herringbone reconstruction. Chalcogen vacancies, pristine WS 2 , Au face-centered cubic, and Au hexagonal close-packed regions are examined and detected by machine learning methods to demonstrate the potential of artificial intelligence for hyperspectral STS mapping.

36 MATERIALS SCIENCE↗
NASA NTRS2008

Effects of Solute Concentrations on Kinetic Pathways in Ni-Al-Cr Alloys

The kinetic pathways resulting from the formation of coherent gamma'-precipitates from the gamma-matrix are studied for two Ni-Al-Cr alloys with similar gamma'-precipitate volume fractions at 873 K. The details of the phase decompositions of Ni-7.5Al-8.5Cr at.% and Ni-5.2Al-14.2Cr at.% for aging times from 1/6 to 1024 h are investigated by atom-probe tomography, and are found to differ significantly from a mean-field description of coarsening. The morphologies of the gamma'-precipitates of the alloys are similar, though the degrees of gamma'-precipitate coagulation and coalescence differ. Quantification within the framework of classical nucleation theory reveals that differences in the chemical driving forces for phase decomposition result in differences in the nucleation behavior of the two alloys. The temporal evolution of the gamma'-precipitate average radii and the gamma-matrix supersaturations follow the predictions of classical coarsening models. The compositional trajectories of the gamma-matrix phases of the alloys are found to follow approximately the equilibrium tie-lines, while the trajectories of the gamma'-precipitates do not, resulting in significant differences in the partitioning ratios of the solute elements.

Booth-Morrison, Christopher↗
DOE OSTI2020

Thermodynamics of spin-orbit-coupled bosons in two dimensions from the complex Langevin method

We investigate the thermal properties of interacting spin-orbit-coupled bosons with contact interactions in two spatial dimensions. To that end, we implement the complex Langevin method, motivated by the appearance of a sign problem, on a square lattice with periodic boundary conditions. We calculate the density equation of state nonperturbatively in a range of spin-orbit couplings and chemical potentials. In this work, our results show that mean-field solutions tend to underestimate the average density, especially for stronger values of the spin-orbit coupling. Additionally, the finite nature of the simulation volume induces the formation of pseudocondensates. These have been observed to be destroyed by the spin-orbit interactions.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2023

Calibration of the ProtoDUNE Horizontal-Drift position reconstruction using a laser system

Forthcoming in the next decade of neutrino physics advancements is the construction of the Deep Underground Neutrino Experiment (DUNE), a long baseline neutrino oscillation experiment which has the potential to answer fundamental questions such as why there is more matter than antimatter in the universe, and ultimately why we exist at all. A prototype of this experiment, ProtoDUNE, sits in a charged particle test beam at the European Organization for Nuclear Research (CERN) and uses Liquid Argon time projection chambers to image interactions of these particles. ProtoDUNE Single-Phase (ProtoDUNESP) had positively charged hadrons as well as positrons in its initial 2018 beam data run. Because ProtoDUNE is a surface-based time projection chamber, it experiences a constant influx of cosmic rays. These cosmic rays ionize the liquid argon within the detector, resulting in an accumulation of slow moving positive ions towards the cathode. This local charge distribution results in electric field non uniformities, which can have a significant effect on the accuracy of the event reconstruction. This paper outlines a monte carlo simulation study which adapts methodology from the MicroBooNE experiment, another neutrino oscillation experiment, to derive electric field correction maps which can correct for distortions of the electric field within the detector. These correction maps accurately estimate the electric field throughout the detector volume and correct for uncertainties in reconstructed event data enabling for physics discoveries.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Effects of drive pulse shape on graded metal pushered single shell capsule implosions on the National Ignition Facility

Graded metal pushered single shells (PSS) are a viable alternative to low-Z capsules (Z is the atomic number) for indirect drive inertial confinement fusion implosions due to enhanced core tamping and radiation trapping, but they can be compromised by the pusher mixing with the fuel. We compare 2-shock and 3-shock laser pulses for Be/Cr PSS capsules filled with deuterium–tritium gas fuel at 6 mg/cc density. 1D radiation-hydrodynamic simulations predict higher core compression and, hence, ∼2× higher fusion yield for the 3-shock drive than for 2-shock. Nevertheless, we observe similar core ion temperatures and fusion yields for both drives. The implosion burn duration is 25% shorter and the core volume is ∼2.5× smaller for the 3-shock drive than for 2-shock, consistent with a higher compression. 1D LASNEX mix simulations using a buoyancy-drag model matching the measured yields also agree with the observed core sizes and burn durations and suggest ∼40% and ∼70% yield degradations for 2-shock and 3-shock drives due to hydrodynamic instabilities and atomic mix at the pusher–fuel interface. At the same time, 2D HYDRA simulations show that mid-mode (2–250) instability degradations are negligible for the 2-shock implosion (9%) and significant (45%) for 3-shock. Subtracting these from the 1D mix simulations, we infer similar degradations from high-mode instabilities and atomic mix for both drives. Due to its robustness to mid-mode instabilities, future pusher–gas mix studies will use the 2-shock drive.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Variations in GARS powder microstructure as a function of powder chemistry and particle size

The properties of metal produced through powder metallurgy depends on the feedstock used. Powders produced via gas atomization reaction synthesis (GARS) are used to produce oxide dispersion strengthened alloys. The desired powder size range can vary for each consolidation technique. However, powder microstructure also can vary with powder particle size, which in turn can impact the microstructure and properties of the consolidated parts. In this study, GARS powders are characterized via inductively coupled plasma mass spectroscopy, inert gas fusion, and high-resolution x-ray diffraction to determine variations in elemental and phase compositions. Transmission electron microscopy was used to understand microstructure variations as a function of chemistry and size. Across the three batches tested intermetallic content was 0.73–1.35 wt% in the 0-20 μm powder batch and increased to 2.46–3.80 wt% in the coarse 45-106 μm batch. Across all batches, volume percent of surface oxidation decreased with powder diameter, with volume percents within the range of 0.75–1.2 % across 10 μm powder particles, and below 0.4 % across coarse powder particles approximately 100 μm in diameter. These observations were supported by inert gas fusion measurements. However, the oxide layer was thicker in coarse powder particles due to a slower cooling rate. Increasing oxygen content in atomization gas to 2000 ppm and adding yttrium increased both the surface oxidation content and yttrium intermetallic content. Lastly, intermetallic phases within the powder coarsened with powder size. Intermetallic morphology changed from fine spherical intermetallic and columnar dendritic growth to a cellular structure with finer spherical intermetallic, to coarse irregular intermetallic and intermetallic along grain boundaries as a result of slower cooling rate and solidification rate in coarse powder particles. Furthermore, the addition of zirconium does not appear to significantly change intermetallic morphology, but the composition changed from a Y-Fe rich intermetallic to a Y-Zr-Fe intermetallic.

42 ENGINEERING↗
DOE OSTI2025

On the Structural Origin of Fast Li-Ion Cycling in Tetragonal Bronze-Type Nb 8 W 9 O 47

Bronze and bronze-derived, mixed metal oxides are materials of growing interest for lithium-ion battery anodes due to their high-rate capabilities and the potential for high energy densities via multielectron redox. We report on the synthesis and electrochemical properties of the tetragonal tungsten bronzetype phase Nb 8 W 9 O 47 and our investigation into the structural evolution of this phase upon lithium (de)intercalation, with particular attention to how it relates to the fast-cycling capabilities. Electrochemical cycling shows Nb 8 W 9 O 47 can achieve greater than one Li + per transition metal at rates of C/2 or slower and maintains a capacity equivalent to 0.65 Li + per transition metal at a rate of 20C. Sequential Rietveld analysis of operando X-ray diffraction data reveals anisotropic changes to the unit cell parameters during discharge, accompanied by an off-centering of the transition metals within their octahedral environments. While higher capacities can be accessed below 1.2 V, cells discharged to 1.0 V exhibit a significant expansion of the unit cell volume and reduced Coulombic efficiencies. This report suggests that rigid crystal structures incapable of undergoing polyhedral rotational deformations can instead exploit displacive distortions of the transition metal redox center to enable fast Li-ion cycling with minimal atomic rearrangements.

25 ENERGY STORAGE↗
DOE OSTI2021

Development of a 83 mKr source for the calibration of the CENNS-10 liquid argon detector

We report on the preparation of and calibration measurements with a 83 mKr source for the CENNS-10 liquid argon detector. 83 mKr atoms generated in the decay of a 83 Rb source were introduced into the detector via injection into the Ar circulation loop. Scintillation light arising from the 9.4 keV and 32.1 keV conversion electrons in the decay of 83 mKr in the detector volume were then observed. This calibration source allows the characterization of the low-energy response of the CENNS-10 detector and is applicable to other low-energy-threshold detectors. The energy resolution of the detector was measured to be 9% at the total 83 mKr decay energy of 41.5 keV. Lastly, we performed an analysis to separately calibrate the detector using the two conversion electrons at 9.4 keV and 32.1 keV.

47 OTHER INSTRUMENTATION↗
NASA NTRS1979

The friction and wear of metals and binary alloys in contact with an abrasive grit of single-crystal silicon carbide

Sliding friction experiments were conducted with various metals and iron-base binary alloys (alloying elements Ti, Cr, Mn, Ni, Rh, and W) in contact with single-crystal silicon carbide riders. Results indicate that the coefficient of friction and groove height (corresponding to the wear volume) decrease linearly as the shear strength of the bulk metal increases. The coefficient of friction and groove height generally decrease with an increase in solute content of binary alloys. A separate correlation exists between the solute to iron atomic radius ratio and the decreasing rates of change of coefficient of friction and groove height with increasing solute content. These rates of change are minimum at a solute to iron radius ratio of unity. They increase as the atomic ratio increases or decreases linearly from unity. The correlations indicate that atomic size is an important parameter in controlling friction and wear of alloys.

Miyoshi, K.↗
DOE OSTI2024

Revealing subterahertz atomic vibrations in quantum paraelectrics by surface-sensitive spintronic terahertz spectroscopy

Understanding surface collective dynamics in quantum materials is crucial for advancing quantum technologies. For example, surface phonon modes in quantum paraelectrics are thought to be essential in facilitating interfacial superconductivity. However, detecting these modes, especially below 1 terahertz, is challenging because of limited sampling volumes and the need for high spectroscopic resolution. Here, we report surface soft transverse optical (TO1) phonon dynamics in KTaO 3 and SrTiO 3 by surface-sensitive spintronic terahertz spectroscopy that can sense the collective modes only a few nanometers deep from the surface. In KTaO 3 , the TO1 mode softens and sharpens with decreasing temperature, leveling off at 0.7 terahertz. In contrast, this mode in SrTiO 3 broadens substantially below the quantum paraelectric crossover and coincides with the hardening of a sub–milli–electron volt phonon mode related to the antiferrodistortive transition. These observations that deviate from their bulk properties may have implications for interfacial superconductivity and ferroelectricity. The developed technique opens opportunities for sensing low-energy surface collective excitations.

Chu, Zhaodong↗
NASA NTRS1990

Ignition and combustion characteristics of metallized propellants

Shakedown and calibration of the experimental apparatus designed to study secondary atomization and ignition characteristics of aluminum slurry propellants was begun and nears completion. The burner was tested over an array of equivalence ratios and oxygen mass fractions to determine the permissible range of operating conditions. A burner flow control system was designed and fabricated which permits independent control of flame stoichiometry and oxidant O2 concentrations. The Sun slurry formulation was selected as the base for initial testing. Laser beam waists at the focal volume of the single particle sizing system were determined to be 396 microns for the Ar-ion and 81 microns for the He-Ne laser. Size calibrations using pinholes were completed and compared to Mie theory for light scattering from particles. A vibrating office droplet generator was used to test the single particle sizing system dynamically by producing a water droplet laden gas flow. The data acquisition and analysis programming was completed and testing is in progress. From initial results, the particle sizing, atomization and ignition detection systems appear to be performing as expected.

Turns, S. R.↗