Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WELDING, GAS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Compressed Natural Gas Vehicle Maintenance Facility Modification Handbook

To ensure the safety of personnel and facilities, vehicle maintenance facilities are required by law and by guidelines of the National Fire Protection Association (NFPA) and the International Fire Code (IFC) to exhibit certain design features. They are also required to be fitted with certain fire protection equipment and devices because of the potential for fire or explosion in the event of fuel leakage or spills. All fuels have an explosion or fire potential if specific conditions are present. The hazard presented by liquid fuels, such as gasoline and diesel, results from the spillage of these liquids and subsequent ignition of vapors, causing a fire or explosion. Facilities that maintain liquid-fueled vehicles and implement appropriate safety measures are protected with ventilation systems designed to capture liquid fuel vapors at or near floor level. To minimize the potential for ignition in the event of a spill, receptacles, electrical fixtures, and hot-work operations, such as welding, are located outside of these areas. Compressed natural gas (CNG) is composed of methane with slight amounts of heavier simple hydrocarbons. Maintenance facilities that maintain CNG vehicles indoors must be protected against fire and explosion. However, the means of ensuring safety are different from those employed for liquid fuels because of the gaseous nature of methane and the fact that it is lighter than air. Because CNG is lighter than air, a release will rise to the ceiling of the maintenance facility and quickly dissipate rather than remaining at or near floor level like liquid fuel vapors. Although some of the means of protection for CNG vehicle maintenance facilities are similar to those used for liquid-fueled vehicles (ventilation and elimination of ignition sources), the types and placement of the protection equipment are different because of the behavior of the different fuels. The nature of gaseous methane may also require additional safeguards, such as combustible gas detectors and control systems, or specialized space heating, which are not needed in facilities servicing liquid-fuel vehicles. This handbook covers maintenance facilities that service CNG-fueled vehicles. Although similar requirements are mandated for liquefied natural gas (LNG) or liquefied petroleum gas (LPG) fueled vehicles, LNG and LPG are not covered in this handbook.

30 DIRECT ENERGY CONVERSION↗

Specifications of FIPD Fission Gas Release Data

All fission gas release data stored in the Fuels Irradiation & Physics Database (FIPD) was originally measured using the Gas Assay, Sample and Recharge (GASR) System in the Hot Fuel Examination Facility (HFEF). It is therefore called GASR data in FIPD. During the measurement of a sample, such as an irradiated EBR-II fuel element/capsule, a pinhole-sized region near the top of the element plenum was melted by a laser. Plenum gas then expanded into a calibrated volume (note: in this document, “sample” and “capsule/element” are used interchangeably consistent with GASR documents in FIPD). The pressure rise in the volume was recorded. Helium backfilling and expansion was then performed to determine the sample (e.g., fuel element plenum) volume using Boyle’s Law and assuming ideal gas behavior at constant temperature. With the plenum volume and the recorded pressure rise, the sample (e.g., fuel element plenum) pressure was derived with assumption of ideal gas law behavior. The plenum volume and pressure as well as the cladding temperature during the measurement were collected (GASR data in FIPD). Other records associated with the fission gas release data include: raw GASR data records including volumes and post-puncture pressures of seal head/sealing head and manifold, calibration data, backfilling gas pressure data, and the data analysis records. A sample(s) of the fission gas released from the plenum was collected by the GASR system into sample bottles. The chemical and isotopic composition of the gas sample was analyzed separately from GASR data, and will be discussed in a separate specification. The plenum volume, pressure, and cladding temperature during the measurement are typically utilized to determine the number of moles of gas in the plenum. This quantity is often compared to the number of moles of gas generated by fission events. However, calculating these values and their associated uncertainty is beyond the scope of this document, as it necessitates additional assumptions. The most important document to understand the FIPD fission gas data is the GASR operational manual (title: Gas Assay, Sample and Recharge System (GASR) operation and maintenance manual, HFEF/N OMM 4381, DOC. NO. W0018-0032-ES-00). This manual provides: (1) description of the GASR and the functions of each component (laser drilling, welding, seal head/sealing head, manifold, vacuum system, sample system, purge and gas tag system, etc.); (2) step-by-step guidance on calibrations, operations, and measurements; and (3) maintenance procedures and other details relating to the structure and operation of the GASR. Note that the original GASR operated until 2020. A new GASR with the same design and measurement methodology was installed in 2021. The specifications of the GASR presented on the HFEF website at this time are consistent with the ones given in the operational manual. The methods to calculate the plenum volume and pressures were not included in the operational manual, but were recorded in the legacy data analysis files. Details of the methods are given in Chapter 3.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The development of natural gas and hydrogen pipeline capital cost estimating equations

Natural gas pipeline cost data collected by the Oil and Gas Journal (O&GJ) for interstate pipelines constructed from 1980 through 2017 were used to develop capital cost estimating equations that are a function of pipeline diameter, length, and U.S. region. Equations were developed for material, labor, miscellaneous, and right-of-way costs, the four cost components in the O&GJ data, for six different regions of the United States (U.S.). Each equation is a function of pipeline diameter and length. Adjustment mechanisms were then developed for converting the natural gas pipeline equations into equations for estimating the costs of hydrogen pipelines. These adjustments were based in part on an analysis completed by the National Institute for Standards and Technology (NIST). Here the results of this work were used to update cost models in the Hydrogen Delivery Scenario Analysis Model (HDSAM), developed by Argonne National Laboratory for the U.S. Department of Energy’s Hydrogen Program. Our analysis shows a wide range of pipeline cost across different U.S. regions, especially with respect to labor and right-of-way costs. The developed cost formulas for hydrogen pipelines are both important and timely as hydrogen is being considered as a zero-carbon energy carrier with the potential to decarbonize all energy sectors, and the cost of hydrogen transportation is essential for techno-economic analysis of its potential use in these sectors.

03 NATURAL GAS↗

Advanced FIB-based Preparation of Cryogenically-prepared Specimens for APT Analysis

The utilization of the focused ion beam scanning electron microscope (FIB-SEM) has aided the application of Atom Probe Tomography (APT) to a continually-growing variety of materials, including soft biological materials. However, the regular application of APT to hydrated interfaces such as those found in biological and environmental materials is lacking in large part due to difficulties in specimen preparation under high and ultra-high vacuum conditions. Although a FIB-SEM based cryogenic specimen preparation approach offers a rational route to the preparation of such specimens for APT analysis, many practical aspects such as welding and limitations in the cryo stage manipulation makes it challenging for routine liftout of site-targeted specimens. In this work, we describe our recent efforts in the development of a site-specific liftout and attachment scheme for cryogenically cooled specimens involving a combination of redeposition and overcoating of organic and organometallic molecules, as shown in Fig. 1a-d for a cryogenically-frozen corroded glass sample containing a hydrated porous gel surface layer. Application of an annular milling pattern to the frozen specimens leads to a needle-shaped morphology necessary for APT analysis with the targeted water-ice filled porous corroded silicate glass region of interest near the apex. Using a custom shuttle device and environmental transfer hub at PNNL to facilitate environmentally-protected specimen transfer, APT analysis was applied to directly map, for the first time, a water/solid interface in 3D to reveal the complex nanoscale water-filled porous network of corroded glass. Application of this unique specimen preparation approach to biological specimens will also be discussed, as well as the application of a unique cryo nanomaniupulator with integrated gas injection system to enable controlled FIB-based welding under cryogenic temperatures.

59 BASIC BIOLOGICAL SCIENCES↗

Innovative Tools Advance Revolutionary Weld Technique

The iconic, orange external tank of the space shuttle launch system not only contains the fuel used by the shuttle s main engines during liftoff but also comprises the shuttle s backbone, supporting the space shuttle orbiter and solid rocket boosters. Given the tank s structural importance and the extreme forces (7.8 million pounds of thrust load) and temperatures it encounters during launch, the welds used to construct the tank must be highly reliable. Variable polarity plasma arc welding, developed for manufacturing the external tank and later employed for building the International Space Station, was until 1994 the best process for joining the aluminum alloys used during construction. That year, Marshall Space Flight Center engineers began experimenting with a relatively new welding technique called friction stir welding (FSW), developed in 1991 by The Welding Institute, of Cambridge, England. FSW differs from traditional fusion welding in that it is a solid-state welding technique, using frictional heat and motion to join structural components without actually melting any of the material. The weld is created by a shouldered pin tool that is plunged into the seam of the materials to be joined. The tool traverses the line while rotating at high speeds, generating friction that heats and softens but does not melt the metal. (The heat produced approaches about 80 percent of the metal s melting temperature.) The pin tool s rotation crushes and stirs the plasticized metal, extruding it along the seam as the tool moves forward. The material cools and consolidates, resulting in a weld with superior mechanical properties as compared to those weld properties of fusion welds. The innovative FSW technology promises a number of attractive benefits. Because the welded materials are not melted, many of the undesirables associated with fusion welding porosity, cracking, shrinkage, and distortion of the weld are minimized or avoided. The process is more energy efficient, safe (no toxic smoke or shielding gas, liquid metal splatter, arcing, dangerous voltage, or radiation), and environmentally sound (no consumables, fumes, or noise) than fusion welding. Under computer control, an automated FSW machine can create welds with high reproducibility, improving efficiency and overall quality of manufactured materials. The process also allows for welding dissimilar metals as well as those metals considered to be "unweldable" such as the 7xxx series aluminum alloys. Its effectiveness and versatility makes FSW useful for aerospace, rail, automotive, marine, and military applications. A downside to FSW, however, is the keyhole opening left in the weld when the FSW pin tool exits the weld joint. This is a significant problem when using the FSW process to join circumferential structures such as pipes and storage containers. Furthermore, weld joints that taper in material thickness also present problems when using the conventional FSW pin tool, because the threaded pin rotating within the weld joint material is a fixed length. There must be capability for the rotating pin to both increase and decrease in length in real time while welding the tapered material. (Both circumferential and tapered thickness weldments are found in the space shuttle external tank.) Marshall engineers addressed both the keyhole and tapered material thickness problems by developing the auto-adjustable pin tool. This unique piece of equipment automatically withdraws the pin into the tool s shoulder for keyhole closeout. In addition, the auto-adjustable pin tool retracts, or shortens, the rotating pin while welding a weld joint that tapers from one thickness to a thinner thickness. This year, the impact of the Marshall innovation was recognized with an "Excellence in Technology Transfer Award" from the Federal Laboratory Consortium.

Source record↗

MARVEL Guard Vessel System FEA and ASME Analysis

The INL is seeking to build the first microreactor in the United States, and the first advanced reactor in over 50 years. With the Microreactor Applications Research, Validation & EvaLuation (MARVEL) Project, this microreactor should be operational within a significantly faster timescale than has ever been seen in the nuclear industry. It uses two passive-convection loops, primarily Sodium Potassium eutectic (NaK), and Ga-In-Sn eutectic as an intermediate fluid. Due to the high reactivity of NaK, the primary coolant loop requires a secondary confinement boundary to prevent uncovering of the core in the event of a NaK leak. This secondary boundary is mostly accomplished through the addition of the Guard Vessel, which is a bucket-like metal containment, which is welded onto the primary boundary to maintain an inert gas environment and pressure

99 GENERAL AND MISCELLANEOUS↗

Safety of Li-SOCl2 cells

The safety of lithium thionyl chloride cells has been a concern of JPL for some time in the development of these cells for NASA's use. Because the safety problems are complex and several issues are interrelated it was decided that it would be best to put together an organized review of the safety issues, which are reviewed here. Hazards are classified in three categories: (1) cell leakage, a problem dealing with construction or materials; (2) venting of toxic gases through seals and welds, considered a mild hazard in which electrolyte and gas is released; and (3) violent rupture or controlled rupture of cells with the possibility of explosion of the materials inside. These hazards and their effects are detailed along with possible ways of dealing with them.

Subbarao, S.↗

Commercialization of dish-Stirling solar terrestrial systems

The requirements for dish-Stirling commercialization are described. The requirements for practical terrestrial power systems, both technical and economic, are described. Solar energy availability, with seasonal and regional variations, is discussed. The advantages and disadvantages of hybrid operation are listed. The two systems described use either a 25-kW free-piston Stirling hydraulic engine or a 5-kW kinematic Stirling engine. Both engines feature long-life characteristics that result from the use of welded metal bellows as hermetic seals between the working gas and the crankcase fluid. The advantages of the systems, the state of the technology, and the challenges that remain are discussed. Technology transfer between solar terrestrial Stirling applications and other Stirling applications is predicted to be important and synergistic.

Ross, Brad↗

NASA Tech Briefs, November 2005

Topics covered include: Laser System for Precise, Unambiguous Range Measurements; Flexible Cryogenic Temperature and Liquid-Level Probes; Precision Cryogenic Dilatometer; Stroboscopic Interferometer for Measuring Mirror Vibrations; Some Improvements in H-PDLCs; Multiple-Bit Differential Detection of OQPSK; Absolute Position Encoders With Vertical Image Binning; Flexible, Carbon-Based Ohmic Contacts for Organic Transistors; GaAs QWIP Array Containing More Than a Million Pixels; AutoChem; Virtual Machine Language; Two-Dimensional Ffowcs Williams/Hawkings Equation Solver; Full Multigrid Flow Solver; Doclet To Synthesize UML; Computing Thermal Effects of Cavitation in Cryogenic Liquids; GUI for Computational Simulation of a Propellant Mixer; Control Program for an Optical-Calibration Robot; SQL-RAMS; Distributing Data from Desktop to Hand-Held Computers; Best-Fit Conic Approximation of Spacecraft Trajectory; Improved Charge-Transfer Fluorescent Dyes; Stability-Augmentation Devices for Miniature Aircraft; Tool Measures Depths of Defects on a Case Tang Joint; Two Heat-Transfer Improvements for Gas Liquefiers; Controlling Force and Depth in Friction Stir Welding; Spill-Resistant Alkali-Metal-Vapor Dispenser; A Methodology for Quantifying Certain Design Requirements During the Design Phase; Measuring Two Key Parameters of H3 Color Centers in Diamond; Improved Compression of Wavelet-Transformed Images; NASA Interactive Forms Type Interface - NIFTI; Predicting Numbers of Problems in Development of Software; Hot-Electron Photon Counters for Detecting Terahertz Photons; Magnetic Variations Associated With Solar Flares; and Artificial Intelligence for Controlling Robotic Aircraft.

Source record↗

High Temperature Additive Architectures for 65% Efficiency (Final Technical Report)

This project aimed to develop advanced high-temperature additive components that contribute towards the DOE’s goal for advanced gas turbines that are capable of at least 65% efficiency in combined cycle application. The objective was to leverage state-of-the-art additive manufacturing to develop an innovative stage 1 turbine nozzle (S1N) that can provide cooling flow savings while maintaining the component durability expected in today’s gas turbines. The program had two phases. Phase I was a conceptual phase for novel advanced cooling designs enabled by additive manufacturing, as well as proposals for validation. Phase II included execution of the Phase I conceptual design, including manufacturing of prototype hardware and validation within an environment that is similar to engine operation. During Phase I of the program, the team devised a concept to reduce cooling air usage. The cooling air used in the side walls is filmed out along the side walls, while the cooling air used in the airfoil is eventually directed to near-wall channels and exits holes along the airfoil trailing end. During this program, the team performed additive trials to analyze the geometric limitations of additive manufacturing. This helped the team understand minimum wall thicknesses, hole sizes, and cooling channel dimensions among other limits. Phase II of this program pushed GE Vernova beyond its previous experience of designing and manufacturing an additively manufactured hot gas path component. Modern hot gas path components utilize material chemistries that are traditionally hard to weld, such as cast Renè 108, and exhibit solidification cracking when additively manufactured using Direct Metal Laser Melting (DMLM). Note that AM108 is a powder form of Renè 108. A S1N with advanced cooling is larger and more complex than parts previously built by additive manufacturing and required new learnings to resolve risks around solidification cracking. Finally, the team validated the design in a combustion rig that replicated operation in a gas turbine. In order to properly quantify the benefits of the new additive design, a baseline was also tested in the rig and operated under the same conditions. In addition, an uncertainty analysis was done to quantify any sources of error that could impact the results. At the end of the validation effort, it was determined that the additive nozzle exceeded the 15% reduction in cooling flow goal even with the worst-case assumptions for uncertainty.

03 NATURAL GAS↗

Thermal Model Heat Rate Predictions of the AGR-5/6/7 Experiment

Several fuel and material irradiation experiments have been planned for the U.S. Department of Energy Advanced Gas Reactor Fuel Development and Qualification Program, which supports the development and qualification of tristructural isotropic (TRISO) coated particle fuel for use in high-temperature gas-cooled reactors. The goals of these experiments are to provide irradiation performance data to support fuel process development, qualify fuel for normal operating conditions, support development of fuel performance models and codes, and provide irradiated fuel and materials for post-irradiation examination and safety testing. Originally planned and named as separate fuel experiments, but subsequently combined into a single test train. AGR-5/6/7 will test low-enriched uranium oxycarbide (UCO – a heterogeneous mixture of uranium oxide and uranium carbide) TRISO fuel. The AGR-5/6 portion of the experiment will provide data to support qualification of the selected reference fuel design, while the AGR-7 portion will serve as a margin test, irradiating the fuel beyond normal operating conditions. During irradiation, the temperature in each capsule is controlled by varying the helium / neon gas mixture flowing through the capsule until the desired thermocouple temperature is reached. Further adjustments can be made by changing the lobe power and the neutron filter. Three neutron filters are available to use as the experiment burns up the fissionable fuel. A thermal finite element model has been created for the five capsules comprising the AGR-5/6/7 experiment. Heat rates from a physics analysis are imported into the model along with fast neutron fluence. Graphite shrinkage due to the fast neutron fluence is incorporated into the model. Gas gaps change as a function of fast neutron fluence. Radiation heat transfer is a major contributor in this model. This is a large model with more than 1 million finite element brick elements. More than 150 different parts are modeled in the finite element model and communicate with each other from a heat transfer sense. More than 50 thermocouples are used in the experiment and are compared to actual measurements. The experiment is composed of five separate stainless steel capsules all welded together. This paper presents a method used to predict the gas mixture in the event that all of the thermocouples fail in a particular capsule. Curve fitting of heat rates from previous cycles and projecting them into the future is the basis of the method.

36 MATERIALS SCIENCE↗

Gas velocity and temperature near a liquid rocket injector face

The gas flow near the injector of a liquid propellant rocket was investigated by rapidly inserting butt-welded platinum-platinum rhodium thermocouples through the injector into the chamber. The transient responses of the thermocouples were analyzed to determine average gas temperatures and velocities. A method of fitting exponential curves to repeated measurements of the transient temperature at several positions near the injector face produced consistent results. Preliminary tests yielded gas flow directions and gas compositions at the injector face. Average gas temperatures were found to be between 3100 (1700) and 3500 F (1950 C) and the average gas velocities between 550 (170) and 840 feet/second (260 m/sec).

Boylan, D. M.↗

Agglutinates as indicators of lunar soil maturity - The rare gas evidence at Apollo 16

The weight percent of lunar agglutinic glass (glass-welded aggregates resulting from micrometeorite impacts) in Apollo 16 bulk soils is considered with respect to quantities of trapped rare gases, e.g., He-4, Ne-20, Ar-36, Kr-84, and Xe-132, in an effort to determine the cumulative time a given soil sample has spent exposed on the lunar surface. The agglutinic glass, which reacts strongly in a magnetic field, is obtained by the standard fluid (methanol)-magnetic technique. It is noted that the absolute concentrations of trapped rare gases all show a linear relationship with increasing agglutinic glass content.

Charette, M. P.↗

INFLUENCE OF SUPPLEMENTARY ARGON GAS SHIELDING ON THE MICROSTRUCTURE AND MECHANICAL BEHAVIOR OF SS316L ADDITIVELY MANUFACTURED BY DIRECTED ENERGY DEPOSITION

The dissolution of atmospheric gases into parts additively manufactured by directed energy deposition (DED) has long been of concern, and stock shielding solutions have usually proven inadequate at fully removing atmospheric gases from weld beads. The objective of this work was to design a new supplementary argon gas shroud for a specific DED printer and evaluate its effect on microstructure and macroscopic properties of SS316L and the potential for printing more reactive metals such as Ti-6Al-4V. This was investigated by printing four SS316L sample blocks, two with and two without the shroud, each printed in two different orientations. These samples were subsequently evaluated with inert gas fusion (IGF), SEM/EDS imaging, and tensile tests. The shroud reduced oxygen content by 0.019-0.031%, and SEM imaging revealed fewer oxide inclusions. A more dramatic reduction of 0.13% oxygen and 0.171% nitrogen was observed by the inert gas fusion of Ti-6Al-4V samples. Overall, the results indicated the shroud was successful at reducing atmospheric gas uptake within the print region and may enable the printing of reactive metal powders in DED systems.

Helvie, Kyle↗

Visible Arc Emission Spectrometry During Pulsed-Current GMAW [Slides]

GBE Shielding Gas Disturbance Metric (GBESGDM) is sensitive to shielding gas disturbances caused by: (1) lack of shielding due to decreasing gas flow rate; (2) change in shielding gas composition; (3) dirty/contaminated base plate; and (4) changes in welding parameters.

36 MATERIALS SCIENCE↗

Atmosphere Effects in Laser Powder Bed Fusion: A Review

The use of components fabricated by laser powder bed fusion (LPBF) requires the development of processing parameters that can produce high-quality material. Manipulating the most commonly identified critical build parameters (e.g., laser power, laser scan speed, and layer thickness) on LPBF equipment can generate acceptable parts for established materials and moderately intricate part geometries. The need to fabricate increasingly complex parts from unique materials drives the limited research into LPBF process control using underutilized parameters, such as atmosphere composition and pressure. As presented in this review, manipulating atmosphere composition and pressure in laser beam welding has been shown to expand processing windows and produce higher-quality welds. The similarities between laser beam welding and laser-based AM processes suggest that this atmosphere control research could be effectively adapted for LPBF, an area that has not been widely explored. Tailoring this research for LPBF has significant potential to reveal novel processing regimes. This review presents the current state of the art in atmosphere research for laser beam welding and LPBF, with a focus on studies exploring cover gas composition and pressure, and concludes with an outlook on future LPBF atmosphere control systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

AMVOS: Additive Manufacturing Video Object Segmentation Dataset

This dataset provides labeled video frames from four additive manufacturing (AM) processes for video object segmentation (VOS) tasks. It contains 90 video segments comprising 900 individually annotated frames across five AM datasets: laser hot-wire directed energy deposition (LHW-DED), tungsten inert gas wire arc additive manufacturing (TIG-WAAM), plasma arc welding (PAW), visible-light polymer extrusion (visPolymer), and near-infrared polymer extrusion (irPolymer). Each video segment consists of 10 contiguous frames with corresponding pixel-level object instance annotations. Depending on the process, two of four object classes are labeled per frame: Melt Pool, Feed Wire, Nozzle, or Material. Raw frames are provided as .jpg files and annotations as palettized .png files. The dataset follows the directory structure of established VOS benchmarks (DAVIS, YouTube-VOS, MOSE), enabling direct integration into VOS model training and evaluation pipelines for foundation model fine-tuning, domain adaptation, or zero-shot performance benchmarking. Data was collected at Oak Ridge National Laboratory's Manufacturing Demonstration Facility.

Wetzel, Jon [ORNL]↗