Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “UV”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Robust chain aggregation of low-entropy rigid ladder polymers in solution

Conjugated polymers have been widely investigated where ladder-type conjugated polymers receive more attention due to their rigid backbones and extraordinary properties. However, the understanding of how the rigid conformation of ladder polymers translates to material properties is still limited. Here, we systematically investigated the solution aggregation properties of a carbazole-derived conjugated ladder polymer (LP) and its analogous non-ladder control polymer (CP) via light scattering, neutron scattering, and UV-vis absorption spectroscopy characterization techniques, revealing a highly robust, temperature-insensitive aggregation behavior of the LP. The experimental findings were further validated by computational molecular dynamics simulations. Here we found that the peak positions and intensities of the UV spectra of the LP remained constant between 20 °C and 120 °C in chlorobenzene solution. The polymer also showed a stable hydrodynamic radius measured by dynamic light scattering from 20 °C to 70 °C in the chlorobenzene solution. Using small-angle neutron scattering, no Guinier region was reached in the measured q range down to 0.008 Å –1 , even at elevated temperature. In contrast, the non-ladder control polymer CP was fully soluble in the chlorobenzene solvent without the observation of any notable aggregates. The Brownian dynamics simulation showed that during polymer aggregation, the entropy change of the LP was significantly less negative than that of the non-ladder control polymer. These findings revealed the low entropy nature of rigid conjugated ladder polymers and the low entropy penalty for their aggregation, which is promising for highly robust intermolecular interactions at high temperatures. Such a unique thermodynamic feature of rigid ladder polymers can be leveraged in the design and application of next-generation electronic and optoelectronic devices that function under unconventional high temperature conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

The Universe at z > 10: predictions for JWST from the universemachine DR1

The James Webb Space Telescope (JWST) is expected to observe galaxies at z > 10 that are presently inaccessible. Here, we use a self-consistent empirical model, the universemachine, to generate mock galaxy catalogues and light-cones over the redshift range z = 0-15. These data include realistic galaxy properties (stellar masses, star formation rates, and UV luminosities), galaxy–halo relationships, and galaxy–galaxy clustering. Mock observables are also provided for different model parameters spanning observational uncertainties at z < 10. We predict that Cycle 1 JWST surveys will very likely detect galaxies with M* > 10 7 M⊙ and/or M 1500 < -17 out to at least z ~ 13.5. Number density uncertainties at z > 12 expand dramatically, so efforts to detect z > 12 galaxies will provide the most valuable constraints on galaxy formation models. Additionally, the faint-end slopes of the stellar mass/luminosity functions at a given mass/luminosity threshold steepen as redshift increases. This is because observable galaxies are hosted by haloes in the exponentially falling regime of the halo mass function at high redshifts. Hence, these faint-end slopes are robustly predicted to become shallower below current observable limits (M* < 10 7 M⊙ or M 1500 > -17). For reionization models, extrapolating luminosity functions with a constant faint-end slope from M 1500 = -17 down to M 1500 = -12 gives the most reasonable upper limit for the total UV luminosity and cosmic star formation rate up to z ~ 12. We compare to three other empirical models and one semi-analytic model, showing that the range of predicted observables from our approach encompasses predictions from other techniques. Public catalogues and light-cones for common fields are available online.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Significance of lysogeny for the metabolism of Desulfovibrio spp. strains isolated from aquatic environments of Georgia

Sulphate-reducing bacteria (SRB) are ecologically important group of anaerobic micro-organisms that can reduce sulphate to form hydrogen sulphide-a toxic gas causing iron corrosion on metal surfaces. In this work, SRB strains were isolated from aquatic environments in the country of Georgia to determine their lysogenicity and the role of temperate phages in host metabolism. SRB strains were isolated in samples from the Black Sea coast of Georgia. Based on their genetic, cytological and physiological properties of bacteria, 10 Georgian isolates were assigned to the genus Desulfovibrio. Temperate bacteriophages were induced from three out of ten strains by UV-exposure. Comparison of metal (Fe and Cr) reduction and utilization of various carbon sources by the wild-type (lysogenic) bacterial strains and their UV-irradiated counterparts was done. Temperate phage in the cells of SRB could alter significant functions of bacteria and may have a contribution in the acquisition of different traits by SRB. This article pointed to a significant role for temperate bacteriophages in the metabolism and metabolic potential of host strains of SRB, which were first isolated from the aquatic environment of Georgia.

temperate phage↗
DOE OSTI2020

Controlled Reduction of Graphene Oxide Using Sulfuric Acid

Sulfuric acid under different concentrations and with the addition of SO 3 (fuming sulfuric acid) was studied as a reducing agent for the production of reduced graphene oxide (RGO). Three concentrations of sulfuric acid (1.5, 5, and 12 M), as well as 12 M with 30% SO 3 , were used. The reduction of graphene oxide increased with H 2 SO 4 concentration as observed by Fourier-transformed infrared spectroscopy and X-ray photoelectron spectroscopy. It was observed that GO lost primarily epoxide functional groups from 40.4 to 9.7% and obtaining 69.8% carbon when using 12 M H 2 SO 4 , without leaving sulfur doping. Additionally, the appearance of hexagonal domain structures observed in transmission electron microscopy and analyzed by selected area electron diffraction patterns confirmed the improvement in graphitization. Although the addition of SO 3 in H 2 SO 4 improved the GO reduction with 74% carbon, as measured by XPS, the use of SO 3 introduced sulfur doping of 1.3%. RGO produced with sulfuric acid was compared with a sample obtained via ultraviolet (UV) irradiation, a very common reduction route, by observing that the RGO produced with sulfuric acid had a higher C/O ratio than the material reduced by UV irradiation. This work showed that sulfuric acid can be used as a single-step reducing agent for RGO without sulfur contamination.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Förster Resonance Energy Transfer and Enhanced Emission in Cs 4 PbBr 6 Nanocrystals Encapsulated in Silicon Nano-Sheets for Perovskite Light Emitting Diode Applications

Encapsulating Cs 4 PbBr 6 quantum dots in silicon nano-sheets not only stabilizes the halide perovskite, but also takes advantage of the nano-sheet for a compatible integration with the traditional silicon semiconductor. Here, we report the preparation of un-passivated Cs 4 PbBr 6 ellipsoidal nanocrystals and pseudo-spherical quantum dots in silicon nano-sheets and their enhanced photoluminescence (PL). For a sample with low concentrations of quantum dots in silicon nano-sheets, the emission from Cs 4 PbBr 6 pseudo-spherical quantum dots is quenched and is dominated with Pb 2+ ion/silicene emission, which is very stable during the whole measurement period. For a high concentration of Cs 4 PbBr 6 ellipsoidal nanocrystals in silicon nano-sheets, we have observed Förster resonance energy transfer with up to 87% efficiency through the oscillation of two PL peaks when UV excitation switches between on and off, using recorded video and PL lifetime measurements. In an area of a non-uniform sample containing both ellipsoidal nanocrystals and pseudo-spherical quantum dots, where Pb 2+ ion/silicene emissions, broadband emissions from quantum dots, and bandgap edge emissions (515 nm) appear, the 515 nm peak intensity increases five times over 30 min of UV excitation, probably due to a photon recycling effect. This irradiated sample has been stable for one year of ambient storage. Cs 4 PbBr 6 quantum dots encapsulated in silicon nano-sheets can lead to applications of halide perovskite light emitting diodes (PeLEDs) and integration with traditional semiconductor materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Photopolymerizable Sol-gel Synthesis for Faster Manufacturing of Surrogate Nuclear Debris

Simulated debris is used to train first responders for potential nuclear detonations. Sol gel chemistry has been used to produce surrogate material for these training exercises, but the current average production time is 4 hours. Optimization using UV-polymerizable sol gel precursors can potentially decrease time as well as cost of the production process. FT-IR spectroscopy was used to measure and compare gelation kinetics of the standard and photopolymerizable sol gel synthetic procedures. Addition of the UV-polymerizable precursors and controlling the aqueous phase volume resulted in a 120-fold decrease in vitrification time.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2023

Photo-Curing 3D Printing of Thermosetting Sacrificial Tooling for Fabricating Fiber-Reinforced Hollow Composites

Carbon fiber-reinforced hollow composites play a vital role in lightweighting modern cars and aircrafts. Fabrication of such hollow composites with seamless internal finish requires sacrificial tooling that can be used under pressure and high temperature. For the very first time, high performance sacrificial tooling that can be used to fabricate fiber-reinforced hollow composites is produced using photocuring 3D printing technology. This is achieved by developing UV-curable resins containing highly soluble yet hydrolysable acetal acrylate cross-linker and hydrophilic 4-acryloylmorpholine monomer. It is found that the cross-linker content greatly affects the printing speed. Further, the widely adopted UV post-curing method is found to have negligible impact on improving the thermal-mechanical properties of printed structures. Additionally, after thermal post-treatment, printed sacrificial tooling exhibits a heat deflection temperature of 112 °C at 0.455 MPa and an average coefficient of linear thermal expansion of 59 ppm °C -1 between 30 and 100 °C. As a result, printed tooling enables fabrication of carbon fiber-reinforced hollow composites with complex geometry, which shows a tensile strength of 802 MPa and an elastic modulus of 50.2 GPa.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Polymer Canvas with the Stiffness of the Bone Matrix to Study and Control Mesenchymal Stem Cell Response

Reproducing in vitro the complex multiscale physical features of human tissues creates novel biomedical opportunities and fundamental understanding of cell–environment interfaces and interactions. While stiffness has been recognized as a key driver of cell behavior, systematic studies on the role of stiffness have been limited to values in the KPa–MPa range, significantly below the stiffness of bone. Here, in this work, a platform enabling the tuning of the stiffness of a biocompatible polymeric interface up to values characteristic of human bone is reported, which are in the GPa range, by using extremely thin polymer films on glass and cross-linking the films using ultraviolet (UV) light irradiation. It is shown that a higher stiffness is related to better adhesion, proliferation, and osteogenic differentiation, and that it is possible to switch on/off cell attachment and growth by solely tuning the stiffness of the interface, without any surface chemistry or topography modification. Since the stiffness is tuned directly by UV irradiation, this platform is ideal for rapid and simple fabrication of stiffness patterns and gradients, thus representing an innovative tool for combinatorial studies of the synergistic effect of tissue environmental cues on cell behavior, and creates new opportunities for next-generation biosensors, single-cell patterning, and lab-on-a-chip devices.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

Self‐Trapped and Free Exciton Dynamics in Vacuum‐Deposited Cesium Copper Iodide Thin Films

Abstract Highly photoluminescent, lead‐free perovskites are of interest for displays and solid‐state light‐emitting devices. In this report, streak camera‐based time‐resolved emission and transient absorption spanning visible to deep‐ultraviolet (UV) wavelengths are utilized to study self‐trapped and free exciton dynamics in vacuum‐deposited cesium copper halide thin films of CsCu 2 I 3 and Cs 3 Cu 2 I 5 . Self‐trapped exciton emission of CsCu 2 I 3 exhibits more noticeable changes with time in the peak position and width than Cs 3 Cu 2 I 5 . UV‐to‐blue emission is detectable for both compositions, where free exciton emission is distinct for CsCu 2 I 3 . Transient absorption shows loss of ground‐state bleach signals at early time delays for both, and the bleach signal shifts toward higher energy as time delay increases, likely due to strains induced by the newly created self‐trapped excitons. Global analysis performed on the transient absorption results yields time constants in these materials that build an overall dynamic scheme. This work aids in building a complete picture regarding light emission in these promising materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Photochemical Decomposition of Y‐Series Non‐Fullerene Acceptors Is Responsible for Degradation of High‐Efficiency Organic Solar Cells

Abstract Organic photovoltaic cells that employ Y‐series non‐fullerene acceptors (NFAs) have recently achieved impressive power‐conversion efficiencies (>18%). To fulfill their commercial promise, it is important to quantify their operational lifetimes and understand their degradation mechanisms. In this work, the spectral‐dependent photostability of films and solar cells comprising several Y‐series acceptors and the donor polymer PM6 is investigated systematically. By applying longpass filters during aging, it is shown that UV/near‐UV photons are responsible for the photochemical decomposition of Y‐series acceptors; this degradation is the primary driver of early solar cell performance losses. Using mass spectrometry, the vinylene linkage between the core and electron‐accepting moieties of Y‐series acceptors is identified as the weak point susceptible to cleavage under UV‐illumination. Employing a series of device characterization, along with numerical simulations, the efficiency losses in organic photovoltaic cells are attributed to the formation of traps, which reduces charge extraction efficiency and facilitates non‐radiative recombination as the Y‐series acceptors degrade. This study provides new insights for molecular degradation of organic photovoltaic absorber materials and highlights the importance of future molecular design and strategies for improved solar cell stability.

14 SOLAR ENERGY↗
DOE OSTI2021

Surface Functionalization of Black Phosphorus with Nitrenes: Identification of P=N Bonds Using Isotopic Labeling

Abstract: Surface functionalization of two-dimensional crystals is a key path to tuning their intrinsic physical and chemical properties. However, synthetic protocols and experimental strategies to directly probe chemical bonding in modified surfaces are scarce. Introduced here is a mild, surface-specific protocol for the surface functionalization of few-layer black phosphorus nanosheets using a family of photolytically generated nitrenes (RN) from the corresponding azides. By embedding spectroscopic tags in the organic backbone, a multitude of characterization techniques are employed to investigate in detail the chemical structure of the modified nanosheets, including vibrational (infrared, Raman), Xray (emission, photoelectron), CPMAS NMR, and UV-vis spectroscopy. To directly probe the functional groups introduced on the surface, R fragments were selected such that in conjunction with vibrational spectroscopy, 15N-labeling experiments, and DFT methods, diagnostic P=N vibrational modes indicative of iminophosphorane units on the nanosheet surface could be conclusively identified.

Walz, Kendall↗
DOE OSTI2023

Copolymers of vinylferrocene and vinylimidazole for potential sensing applications

Abstract Since imidazole is easily protonated and well known to coordinated to various transition metals, its incorporation into a polymer with ferrocene may result in interesting electronic interactions between the ferrocenyl and imidazolium moieties. To this end, copolymers of vinylferrocene and vinylimidazole were prepared in various ratios by free radical polymerization. The interactions between the ferrocenyl and imidazolium moieties were studied by cyclic voltammetry, UV–Vis spectroscopy and density functional theory (DFT) studies. Cyclic voltammetry of polymer thin films showed multiple oxidation waves at low pH or in the presence of Pb 2+ or Cd 2+ ions. The UV–Vis spectrum of thin films showed an additional absorbance at 625 nm suggesting electronic interactions. In addition, DFT studies indicated that the morphology of the polymer would place some of the ferrocenyl and imidazolium moieties in close proximity.

Polymer Science↗
DOE OSTI2020

Reversible Photoswitching in Poly(2-oxazoline) Nanoreactors

This contribution reports light responsive catalytic nanoreactors based on poly(2-oxazoline) diblock copolymers. The hydrophobic block of the copolymer is a random copolymer consisting of a spiropyran functionalized 2-oxazoline (SPOx) and 2-(but-3-yn-1-yl)-4,5-dihydrooxazole (ButynOx), while the hydrophilic block is based on 2-methyl-2-oxazoline (MeOx). The block copolymer is terminated with tris(2-aminoethyl) amine (TREN) that serves as catalyst in a Knoevenagel condensation. Four block copolymers with different ButynOx/SPOx and hydrophilic/hydrophobic ratios are synthesized and self-assembled through solvent exchange. Micelles and vesicles of various sizes are observed by TEM, which undergo morphological and size changes in response to irradiation with UV light. We hypothesize that these transformations in the nanostructures are caused by increases in the hydrophilicity of the hydrophobic block when spiropyran (SP) isomerizes to merocyanine (MC) in the presence of UV light. The reversible transition from micellar to vesicular nanoreactors resulted in increased reaction kinetics through improved substrate accessibility to the catalytic site, or termination of the catalytic reaction due to polymer precipitation. Furthermore, these nanoreactors present a promising platform towards photoregulating reaction outcomes based on changes in nanostructure morphology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

C−H Activation of Inert Arenes using a Photochemically Activated Guanidinato‐Magnesium(I) Compound

Abstract UV irradiation of solutions of a guanidinate coordinated dimagnesium(I) compound, [{(Priso)Mg} 2 ] 3 (Priso=[(DipN) 2 CNPr i 2 ] − , Dip=2,6‐diisopropylphenyl), in either benzene, toluene, the three isomers of xylene, or mesitylene, leads to facile activation of an aromatic C−H bond of the solvent in all cases, and formation of aryl/hydride bridged magnesium(II) products, [{(Priso)Mg} 2 (μ‐H)(μ‐Ar)] 4 – 9 . In contrast to similar reactions reported for β‐diketiminate coordinated counterparts of 3 , these C−H activations proceed with little regioselectivity, though they are considerably faster. Reaction of 3 with an excess of the pyridine, p ‐NC 5 H 4 Bu t (py Bu t ), gave [(Priso)Mg(py Bu t H)(py Bu t ) 2 ] 10 , presumably via reduction of the pyridine to yield a radical intermediate, [(Priso)Mg(py Bu t ⋅)(py Bu t ) 2 ] 11 , which then abstracts a proton from the reaction solvent or a reactant. DFT calculations suggest two possible pathways to the observed arene C−H activations. One of these involves photochemical cleavage of the Mg−Mg bond of 3 , generating magnesium(I) doublet radicals, (Priso)Mg⋅. These then doubly reduce the arene substrate to give “Birch‐like” products, which subsequently rearrange via C−H activation of the arene. Circumstantial evidence for the photochemical generation of transient magnesium radical species includes the fact that irradiation of a cyclohexane solution of 3 leads to an intramolecular aliphatic C−H activation process and formation of an alkyl‐bridged magnesium(II) species, [{Mg(μ‐Priso −H )} 2 ] 12 . Furthermore, irradiation of a 1 : 1 mixture of 3 and the β‐diketiminato dimagnesium(I) compound, [{( Dip Nacnac)Mg} 2 ] ( Dip Nacnac=[HC(MeCNDip) 2 ] − ), effects a “scrambling” reaction, and the near quantitative formation of an unsymmetrical dimagnesium(I) compound, [(Priso)Mg−Mg( Dip Nacnac)] 13 . Finally, the EPR spectrum (77 K) of a glassed solution of UV irradiated 3 is dominated by a broad featureless signal, indicating the presence of a doublet radical species.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Radiation‐Induced Defects in Uranyl Trinitrate Solids

Abstract Actinides are inherently radioactive; thus, ionizing radiation is emitted by these elements can have profound effects on its surrounding chemical environment through the formation of free radical species. While previous work has noted that the presence of free radicals in the system impacts the redox state of the actinides, there is little atomistic understanding of how these metal cations interact with free radicals. Herein, we explore the effects of radiation (UV and γ) on three U(VI) trinitrate complexes, M[UO 2 (NO 3 ) 3 ] (where M=K + , Rb + , Cs + ), and their respective nitrate salts in the solid state via electron paramagnetic resonance (EPR) and Raman spectroscopy paired with Density Functional Theory (DFT) methods. We find that the alkali salts form nitrate radicals under UV and γ irradiation, but also note the presence of additional degradation products. M[UO 2 (NO 3 ) 3 ] solids also form nitrate radicals and additional DFT calculations indicate the species corresponds to a change from the bidentate bound nitrate anion into a monodentate NO 3 • radical. Computational studies also highlight the need to include the second sphere coordination environment around the [UO 2 (NO 3 ) 3 ] 0,1 species to gain agreement between the experimental and predicted EPR signatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Photophysical and Time‐resolved Infrared Properties of Long‐Lived Rhenium(I) 4,5‐Diazafluorene Tricarbonyl Chromophores

This report investigates the synthesis, structural characterization, fundamental molecular photophysics, electrochemistry, UV-Vis spectroelectrochemistry, and time-resolved infrared spectroscopic properties of eight [fac-Re(dafR)(CO) 3 L] 0/+ complexes, where R=ethyl [(dedaf); 1, 3, 5, 7] or H [(dafH); 2, 4, 6, 8] and L=Cl− (1, 2), imidazole [(Im); 3, 4], 4-ethylpyridine [(4-Etpy); 5, 6], or pyridine [(py); 7, 8]. Universally, 1–8 yield higher energy photoluminescence (PL) emission bands and higher PL quantum yields (up to 53 %) than the classic 2,2’-bipyridine (bpy) and 1,10-phenanthroline (phen) ligated Re(I) tricarbonyl complexes. The excited state lifetimes of 1–8 lie between those corresponding to the bpy and phen derivatives, ranging from 120 and 1300 ns at room temperature. Combinations of reductive UV-Vis spectroelectrochemistry, transient absorption spectroscopy, and time-resolved infrared spectroscopy consistently assigned the lowest excited states in 1–8 being of metal-to-ligand charge transfer (MLCT) character. These new ReI MLCT chromophores follow classic energy gap law behavior and possess the characteristics necessary for serving as valuable photosensitizers suitable to energize excited state electron and energy transfer photochemistry.

Charge transfer↗
DOE OSTI2022

Bio‐Based Piezo‐ and Thermoresistive Photocurable Sensing Materials from Acrylated Epoxidized Soybean Oil

Abstract Bio‐based photocurable polymers are increasingly in demand as environmentally friendly materials for advanced applications. Together with functional fillers, these represent a next step for the generation of functional and active smart materials, compatible with additive manufacturing technologies. Herein, acrylated epoxidized soybean oil (AESO) mixed with different amounts of reduced graphene oxide (rGO) up to 6 wt% in order to obtain UV‐curable piezoresistive and thermoresistive materials, is reported. It is shown that the addition of rGO to AESO hinders the curing process, but always maintains double bond conversions higher than 50%. Composites are characterized by a good dispersion of micrometric filler clusters. Further, the thermal stabilities are close to 300 °C and crosslinking degrees are above 1.75 mmol cm –3 . The Young modulus of the composites decreases with the addition of the rGO fillers, in particular for the higher filler contents, and electrical conductivities up to 0.13 S m –1 are obtained for the composites with the highest rGO content. UV‐curable composites with piezoresistive and thermoresistive responses suitable for applications are thus obtained, characterized by gauge factors around 26 for deformations up to 2% and maximum thermoresistive sensitivity of S = 0.43, values similar to the values obtained for petroleum‐based materials.

Mendes‐Felipe, Cristian↗