SEARCH · Engineering Papers

Results for “Thrust Load”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Composite laminate tailoring with probabilistic constraints and loads

A reliability-based structural synthesis procedure was developed to tailor laminates to meet reliability-based (ply) strength requirements and achieve desirable laminate responses. The main thrust is to demonstrate how to integrate the optimization technique in the composite laminate tailoring process to meet reliability design requirements. The question of reliability arises in fiber composite analysis and design because of the inherent scatter that is observed in the constituent (fiber and matrix) material properties during experimentation. Symmetric and asymmetric composite laminates subject to mechanical loadings are considered as application examples. These application examples illustrate the effectiveness and ease with which reliability considerations can be integrated in the design optimization model for composite laminate tailoring.

Thanedar, P. B.↗

NASA NTRS1990

Composite laminate tailoring with probabilistic constraints and loads

Thanedar, P. B.↗

NASA NTRS1992

Aeroelastic response and blade loads of a composite rotor in forward flight

The aeroelastic response, blade and hub loads, and shaft-fixed aeroelastic stability is investigated for a helicopter with elastically tailored composite rotor blades. A new finite element based structural analysis including nonclassical effects such as transverse shear, torsion related warping and inplane elasticity is integrated with the University of Maryland Advanced Rotorcraft Code. The structural dynamics analysis is correlated against both experimental data and detailed finite element results. Correlation of rotating natural frequencies of coupled composite box-beams is generally within 5-10 percent. The analysis is applied to a soft-inplane hingeless rotor helicopter in free flight propulsive trim. For example, lag mode damping can be increased 300 percent over a range of thrust conditions and forward speeds. The influence of unsteady aerodynamics on the blade response and vibratory hub loads is also investigated. The magnitude and phase of the flap response is substantially altered by the unsteady aerodynamic effects. Vibratory hub loads increase up to 30 percent due to unsteady aerodynamic effects.

Smith, Edward C.↗

NASA NTRS1978

Theoretical study of hull-rotor aerodynamic interference on semibuoyant vehicles

Analytical methods are developed to predict the pressure distribution and overall loads on the hulls of airships which have close coupled, relatively large and/or high disk loading propulsors for attitude control, station keeping, and partial support of total weight as well as provision of thrust in cruise. The methods comprise a surface-singularity, potential-flow model for the hull and lifting surfaces (such as tails) and a rotor model which calculates the velocity induced by the rotor and its wake at points adjacent to the wake. Use of these two models provides an inviscid pressure distribution on the hull with rotor interference. A boundary layer separation prediction method is used to locate separation on the hull, and a wake pressure is imposed on the separated region for purposes of calculating hull loads. Results of calculations are shown to illustrate various cases of rotor-hull interference and comparisons with small scale data are made to evaluate the method.

Spangler, S. B.↗

NASA NTRS1971

Shock and vibration tests of a SNAP-8 NaK pump

The pump used for reactor cooling in the SNAP 8 space power system was subjected to the expected vehicle launch vibration, and shock loading in accordance with the SNAP 8 environmental specification. Subsequent disassembly revealed damage to the thrust bearing pins, which should be redesigned and strengthened. The unit was operational, however, when run in a test loop after reassembly.

Stromquist, A. J.↗

NASA NTRS1981

RSRA vertical drag test report

The Rotor Systems Research Aircraft (RSRA), because of its ability to measure rotor loads, was used to conduct an experiment to determine vertical drag, tail rotor blockage, and thrust augmentation as affected by ground clearance and flight velocity. The RSRA was flown in the helicopter configuration at speeds from 0 to 15 knots for wheel heights from 5 to 150 feet, and to 60 knots out of ground effect. The vertical drag trends in hover, predicted by theory and shown in model tests, were generally confirmed. The OGE hover vertical drag is 4.0 percent, 1.1 percent greater than predicted. The vertical drag decreases rapidly as wheel height is reduced, and is zero at a wheel height of 6 feet. The vertical drag also decreases with forward speed, approaching zero at sixty knots. The test data show the effect of wheel height and forward speed on thrust, gross weight capability, and power, and provide the relationships for power and collective pitch at constant gross weight required for the simulation of helicopter takeoffs and landings.

Flemming, R. J.↗

NASA NTRS1992

Component test results from the bearing life improvement program for the Space Shuttle Main Engine oxidizer turbopumps

Interim results from a component test program to improve ball bearing life in the Space Shuttle Main Engine oxygen turbopumps are presented. Two specific bearing applications, using liquid oxygen as the bearing coolant, are addressed. The first, the thrust bearing of the low pressure pump, operates at relatively slow speed with predominantly axial load and little temperature rise in the bulk coolant. Testing has demonstrated a very significant reduction in bearing wear by increasing the bearing internal clearance. Heat generation data was obtained that indicates heavy, intermittent cage-to-ball contact occurs, providing a possible explanation for the observed wear. The second application is the turbine end bearings of the high pressure pump. These bearings operate at high speed and load with the possibility of significant coolant vaporization. Tests on production bearings and bearings having modified internal clearance and curvature yielded scattered but generally poor lives. A dramatic improvement was achieved by coating the standard cage with a thin film of fluorinated ethylene propylene and 15 percent molybdenum disulfide. Very promising results have also been obtained by replacing the standard balls with ones made of silicon nitride, especially in combination with the coated cage.

Keba, John E.↗

NASA NTRS1956

The proper combination of lift loadings for least drag on a supersonic wing

Lagrange's method of undetermined multipliers is applied to the problem of properly combining lift loadings for the least drag at a given lift on supersonic wings. The method shows the interference drag between the optimum loading and any loading at the same lift coefficient to be constant. This is an integral form of the criterion established by Robert T. Jones for optimum loadings. The best combination of four loadings on a delta wing with subsonic leading edges is calculated as a numerical example. The loadings considered have finite pressures everywhere on the plan form. Through the sweepback range the optimum combination of the four nonsingular loadings has about the same drag coefficient as a flat plate with leading-edge thrust.

Grant, Frederick C↗

NASA NTRS2000

Development and Testing of Cooled CMCs for High Thermal Flux Applications

Ceramic Matrix Composites (CMCS) offer the potential for significant weight savings and improved performance for a range of propulsion components utilizing refractory materials. This paper describes the fabrication and testing of functionally graded CMCs produced via a low cost process that represents an order of magnitude cost savings over conventionally fabricated CMCS. Test cylinders were fabricated, characterized and evaluated during exposure to high thermal fluxes of up to 10MW/meters squared at the Laser Hardened Materials Evaluation Laboratory (LHMEL). The bulk density of the CMC tubes was approximately 2.2 grams per cubic centimeters. The performance of cryogenically cooled CMCs was compared with uncooled CMCs against similar thermal loads, and fundamental property data collected for this relatively new breed of CMC. Finally, test thrust cells were fabricated from the functionally graded composite and tested using liquid H2 and O2 propellants at NASA Glen.

Patterson , Mark↗

NASA NTRS1951

Tank Investigation of the Grumman JRF-5 Airplane Equipped with Twin Hydro-Skis TED No. NACA DE 357

A tank investigation has been conducted on a 1/8-size powered dynamic model of the Grumman JRF-5 airplane equipped with twin hydro-skis. The results of tests using two types of skis are presented: one had vertical sides joining the top surface to the chine; the other had the top surface faired to the chine to eliminate the vertical sides. Both configurations had satisfactory longitudinal stability although the model had a slightly greater stable elevator range available when the skis without the vertical sides were attached. Free model tests indicated no instability present when one ski emerged before the other. Considerable excess thrust was available at all speeds with either type of skis. A hump gross load-resistance ratio of 3.37 was obtained with the skis with the vertical sides and 3.53 with the other skis. Landing behavior in smooth water with yaw up to 15deg and roll up to 15deg in opposite directions was satisfactory with either type of skis.

Ramsen, John A.↗

NASA NTRS1976

Calculation of the longitudinal aerodynamic characteristics of wing-flap configurations with externally blown flaps

A theoretical investigation was carried out to extend and improve an existing method for predicting the longitudinal characteristics of wing flap configurations with externally blown flaps (EBF). Two potential flow models were incorporated into the prediction method: a wing and flap lifting-surface model and a turbofan engine wake model. The wing-flap model uses a vortex-lattice approach to represent the wing and flaps. The jet wake model consists of a series of closely spaced vortex rings normal to a centerline which may have vertical and lateral curvature to conform to the local flow field beneath the wing and flaps. Comparisons of measured and predicted pressure distributions, span load distributions on each lifting surface, and total lift and pitching moment coefficients on swept and unswept EBF configurations are included. A wide range of thrust coefficients and flap deflection angles is considered at angles of attack up to the onset of stall. Results indicate that overall lift and pitching-moment coefficients are predicted reasonably well over the entire range. The predicted detailed load distributions are qualitatively correct and show the peaked loads at the jet impingement points, but the widths and heights of the load peaks are not consistently predicted.

Mendenhall, M. R.↗

NASA NTRS1980

Low thrust vehicle concept study

Low thrust chemical (hydrogen-oxygen) propulsion systems configured specifically for low acceleration orbit transfer of large space systems were defined. Results indicate that it is cost effective and least risk to combine the OTV and stowed spacecraft in a single 65 K Shuttle. The study shows that the engine for an optimized low thrust stage (1) does not require very low thrust; (2) 1-3 K thrust range appears optimum; (3) thrust transient is not a concern; (4) throttling probably not worthwhile; and (5) multiple thrusters complicate OTV/LSS design and aggravate LSS loads. Regarding the optimum vehicle for low acceleration missions, the single shuttle launch (LSS and expendable OTV) is most cost effective and least risky. Multiple shuttles increase diameter 20%. The space based radar structure short OTV (which maximizes space available for packaged LSS) favors use of torus tank. Propellant tank pressures/vapor residuals are little affected by engine thrust level or number of burns.

Source record↗

NASA NTRS1971

Development of the Algol III solid rocket motor for SCOUT.

The design and performance of a motor developed for the first stage of the NASA SCOUT-D and E launch vehicles are discussed. The motor delivers a 30% higher total impulse and a 35 to 45% higher payload mass capability than its predecessor, the Algol IIB. The motor is 45 in. in diameter, has a length-to-diameter ratio of 8:1 and delivers an average 100,000-lb thrust for an action time of 72 sec. The motor design features a very high volumetrically loaded internal-burning charge of 17% aluminized polybutadiene propellant, a plasma-welded and heat-treated steel alloy case, and an all-ablative plastic nose liner enclosed in a steel shell. The only significant development problem was the grain design tailoring to account for erosive burning effects which occurred in the high-subsonic-Mach-number port. The tests performed on the motor are described.

Felix, B. R.↗

NASA NTRS1975

The effects on propulsion-induced aerodynamic forces of vectoring a partial-span rectangular jet at Mach numbers from 0.40 to 1.20

An investigation was conducted in the Langley 16-foot transonic tunnel to determine the induced lift characteristics of a vectored thrust concept in which a rectangular jet exhaust nozzle was located in the fuselage at the wing trailing edge. The effects of nozzle deflection angles of 0 deg to 45 deg were studied at Mach numbers from 0.4 to 1.2, at angles of attack up to 14 deg, and with thrust coefficients up to 0.35. Separate force balances were used to determine total aerodynamic and thrust forces as well as thrust forces which allowed a direct measurement of jet turning angle at forward speeds. Wing pressure loading and flow characteristics using oil flow techniques were also studied.

Capone, F. J.↗

NASA NTRS1976

Developments in steady and unsteady aerodynamics for use in aeroelastic analysis and design

A review is given of seven research projects which are aimed at improving the generality, accuracy, and computational efficiency of steady and unsteady aerodynamic theory for use in aeroelastic analysis and design. These projects indicate three major thrusts of current research efforts: (1) more realistic representation of steady and unsteady subsonic and supersonic loads on aircraft configurations of general shape with emphasis on structural-design applications, (2) unsteady aerodynamics for application in active-controls analyses, and (3) unsteady aerodynamics for the frequently critical transonic speed range. The review of each project includes theoretical background, description of capabilities, results of application, current status, and plans for further development and use.

Yates, E. C., Jr.↗

NASA NTRS1981

Structural analysis of cylindrical thrust chambers, volume 3

A system of three computer programs is described for use in conjunction with the BOPAGE finite element program. The programs are demonstrated by analyzing cumulative plastic deformation in a regeneratively cooled rocket thrust chamber. The codes provide the capability to predict geometric and material nonlinear behavior of cyclically loaded structures without performing a cycle-by-cycle analysis over the life of the structure. The program set consists of a BOPACE restart tape reader routine, and extrapolation program and a plot package.

Pearson, M. L.↗

NASA NTRS1984

Electrodynamic Tethers. 1: Power Generator in LEO. 2: Thrust for Propulsion and Power Storage

An electrodynamic tether consists of a long insulated wire in space whose orbital motion cuts across lines of magnetic flux to produce an induce voltage that in typical low orbits averages about 200 v/km. Such a system should be capable of generating substantial electrical power, at the expense of IXB drag acting on its orbital energy. If a reverse current is driven against the induced voltage, the system should act as a motor producing IXB thrust. A reference system was designed, capable of generating 20 KW of power into an electrical load located anywhere along the wire at the expense of 2.6N (20,000 J/sec) drag on the wire. In an ideal system, the conversion between mechanical and electrical energy would reach 100% efficiency. In the actual system part of the 20 KW is lost to internal resistance of the wire, plasma and ionosphere, while the drag force is increased by residual air drag. The 20 KW PMG system as designed is estimated to provide 18.7 KW net power to the load at total drag loss of 20.4 KJ/sec, or an overall efficiency of 92%. Similar systems using heavier wire appear capable of producing power levels in excess of 1 Megawatt at voltages of 2-4 KV, with conversion efficiency between mechanical and electrical power better than 95%. The hollow cathode based system should be readily reversible from generator to motor operation by driving a reverse current using onboard power.

Mccoy, J. E.↗

NASA NTRS1986

Aerodynamic characteristics of several current helicopter tail boom cross sections including the effect of spoilers

Aerodynamic characteristics were determined of three cylindrical shapes representative of tail boom cross sections of the U.S. Army AH-64, UH-60, and UH-1H helicopters. Forces and pressures were measured in a wind-tunnel investigation at the Langley Research Center. Data were obtained for a flow incidence range from -45 to 90 deg and a dynamic pressure range from 1.5 to 50 psf. These ranges provided data representative of full-scale Reynolds numbers and the full range of flow incidence to which these helicopter tail boom shapes would be subjected at low flight speeds. The effects of protuberances such as tail rotor drive-shaft covers and spoilers were evaluated. The data indicate that significant side loads on tail booms of helicopters can be generated and that the addition of spoilers can beneficially alter the side loads. Although an increase in vertical drag occurs, the net effect through reduction of tail rotor thrust required can be an improvement in helicopter performance.

Wilson, J. C.↗