Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TRISO performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Accelerator-Based Irradiation Creep of Pyrolytic Carbon Used in TRISO Fuel Particles for the (VHTR) Very Hight Temperature Reactors

Pyrolytic carbon (PyC) is one of the important structural materials in the TRISO fuel particles which will be used in the next generation of gas-cooled very-high-temperature reactors (VHTR). When the TRISO particles are under irradiation at high temperatures, creep of the PyC layers may cause radial cracking leading to catastrophic particle failure. Therefore, a fundamental understanding of the creep behavior of PyC during irradiation is required to predict the overall fuel performance.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

AGR-5/6/7 Irradiation Experiment Fission Product Mass Balance

This report presents the fission product mass balance for the AGR-5/6/7 TRISO fuel irradiation experiment. The fission product inventories deposited on capsule components outside of the fuel (e.g., stainless-steel shells, graphite holders, Grafoil disks, and associated hardware) were quantified as part of the post-irradiation examination (PIE) to assess the performance of this fuel. Comparisons were made between these inventories and depletion calculations, non-destructive measurements of fuel fission product inventories in the intact fuel compacts, prior AGR experiments, and results from among each of the five distinct AGR-5/6/7 capsules. The data served as estimates of the condensable fission products released from the fuel during irradiation. Excluding Capsule 1 (which experienced accidental damage during irradiation) and Capsule 3 (which was tested at very high irradiation temperatures of >1300°C), the results indicate that the AGR-5/6/7 fuel performed comparably to fuel from earlier AGR experiments. The mass balance results were also used to estimate the number of particles with in-pile SiC failures. Subject to the assumptions made in these estimates, and excluding Capsules 1 and 3, the in-pile SiC failure rates for AGR-5/6/7 are comparable to those observed in AGR-2.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Complete Survey of Fuel Candidates for Microreactor Purposes

This report summarizes various fuel types that may be applicable to several microreactor concepts, which are defined as (1) very high temperature reactors (VHTR), (2) sodium fast reactors (SFR), (3) system for nuclear auxiliary power (SNAP) reactors, (4) gas fast reactors (GFR), and (5) molten salt reactors (MSR). The fuel systems that were assessed include: uranium mononitride (UN), uranium monocarbide (UC), uranium dioxide (UO 2 ), uranium oxycarbide (UCO) Tristructural Isotropic (TRISO), UN TRISO, mixed oxide (MOX), metallic fuels, and metal hydrides. While UCO TRISO has undergone significant testing through the advanced gas reactor (AGR) program, the very high cost necessitates consideration of other fuel types. UN and UC were identified as fuels that should receive further investigation due to their thermophysical and mechanical properties. Minimal irradiation performance data shows that these fuels are good candidate fuels for microreactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Massively Parallel Bayesian Model Calibration and Uncertainty Quantification with Applications to Nuclear Fuels and Materials

The U.S. Department of Energy (DOE)’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program aims to develop predictive capabilities by applying computational methods to the analysis and design of advanced reactor and fuel cycle systems. This program has been providing engineering-scale support for the development of BISON, a high-fidelity and high-resolution fuel performance tool. Fuel behavior in a nuclear reactor is governed by a complex network of mechanisms interacting with various other physics aspects in the reactor system. Any model developed to represent the fuel behavior will likely be idealized resulting in uncertainties in their predictions compared to the observed data. As such, this report was motivated by the need to identify the sources of uncertainties and quantify and propagate them through the fuel model outputs. Such quantification of uncertainties will establish a level of model trustworthiness, identify approaches to improve the model trustworthiness, and even guide optimal experiment design for maximal information gain. To accomplish the uncertainty quantification for computational models, this report has relied on the Bayesian framework which provides probabilistic treatment of models their inputs and outputs. The current state-of-the-art on performing Bayesian Uncertainty Quantification (UQ) for nuclear engineering models using High Performance Computing (HPC) resources have been reviewed. Implementation of capabilities for massively parallel Bayesian UQ in Multiphysics Object-Oriented Simulation Environment (MOOSE) is discussed. Several verification cases are discussed to verify the accuracy of the quantified uncertainties using the developed computational capabilities in MOOSE. Then, the problem of quantifying the uncertainties in TRI-Structural isOtropic (TRISO) fuel silver release is addressed. For the first time, the uncertainties arising from the TRISO Fission Gas Release (FGR) model due to model inadequacy and experimental noise are quantified. Also, the Bayesian capabilities are applied to the calibration of the MATPRO creep model, a widely used model in several fuel assessment cases. The impact of the prediction uncertainties in the MATPRO model on the fuel cladding behavior as part of the TRIBULATION assessment case (which is an integral effects case) is investigated. This report concludes with a discussion on the future work for the UQ for computational models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Validation of the BISON 3D Fuel Performance Code: Temperature Comparisons for Concentrically and Eccentrically Located Fuel Pellets

BISON is a modern finite-element based nuclear fuel performance code that has been under development at the Idaho National Laboratory (USA) since 2009. The code is applicable to both steady and transient fuel behaviour and is used to analyse either 2D axisymmetric or 3D geometries. BISON has been applied to a variety of fuel forms including LWR fuel rods, TRISO-coated fuel particles, and metallic fuel in both rod and plate geometries. Code validation is currently in progress, principally by comparison to instrumented LWR fuel rods. Halden IFA experiments constitute a large percentage of the current BISON validation base. The validation emphasis here is centreline temperatures at the beginning of fuel life, with comparisons made to seven rods from the IFA-431 and 432 assemblies. The principal focus is IFA-431 Rod 4, which included concentric and eccentrically located fuel pellets. This experiment provides an opportunity to explore 3D thermomechanical behaviour and assess the 3D simulation capabilities of BISON. Analysis results agree with experimental results showing lower fuel centreline temperatures for eccentric fuel with the peak temperature shifted from the centreline. The comparison confirms with modern 3D analysis tools that the measured temperature difference between concentric and eccentric pellets is not an artefact and provides a quantitative explanation for the difference.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Acceptance Test Data for BWXT Coated Particle Batches 93172B and 93173B—Defective IPyC and Pyrocarbon Anisotropy

Coated particle batches J52O-16-93172B and J52O-16-93173B were produced by Babcock and Wilcox Technologies (BWXT) as part of the production campaign for the Advanced Gas Reactor Fuel Development and Qualification (AGR) Program’s AGR-5/6/7 irradiation test in the Idaho National Laboratory (INL) Advanced Test Reactor (ATR), but were not used in the final fuel composite. However, these batches may be used as demonstration production-scale coated particle fuel for other experiments. Each batch was coated in a 150-mm-diameter production-scale fluidized-bed chemical vapor deposition (CVD) furnace. Tristructural isotropic (TRISO) coatings were deposited on 425-μm-nominal-diameter spherical kernels from BWXT lot J52R-16-69317 containing a mixture of 15.5%-enriched uranium carbide and uranium oxide (UCO). The TRISO coatings consisted of four consecutive CVD layers: a ~50% dense carbon buffer layer with 100-μm-nominal thickness, a dense inner pyrolytic carbon (IPyC) layer with 40-μm-nominal thickness, a silicon carbide (SiC) layer with 35-μm-nominal thickness, and a dense outer pyrolytic carbon (OPyC) layer with 40-μm-nominal thickness. The TRISO-coated particle batches were sieved to upgrade the particles by removing over-sized and under-sized material, and the upgraded batches were designated by appending the letter A to the end of the batch number (e.g., 93172A). Secondary upgrading by sieving was performed on the A-designated batches to remove particles with missing or very-thin buffer layers that were identified during previous analysis of the individual batches for defective IPyC, as reported in the acceptance test data report for the AGR-5/6/7 production batches [Hunn et al. 2017b]. The additionally-upgraded batches were designated by appending the letter B to the end of the batch number (e.g., 93172B).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Preliminary Analysis of Advanced Reactors Storage, Transportation, and Disposal

Based on the higher interest in Advanced Reactor (AR) deployment (e.g., ARDP[1]) for potential new fuel cycles, the Spent Fuel & Waste Science and Technology (SFWST) Program has begun to evaluate the possible implications of long-term management and final disposition of potential Advance Reactor spent nuclear fuels (SNF) that would be generated in potential advanced reactors. Safely managing and dispositioning the potential future AR SNF, and any other associated radioactive wastes, is the primary focus of this initial preliminary assessment of those. This paper summarizes the efforts by the Spent Fuel & Waste Science and Technology (SFWST) in evaluating characteristics and packaging options for advanced reactor spent nuclear fuel forms. The fuel forms were categorized into three types: (1) tristructural isotropic (TRISO), (2) metallic, and (3) fuel salt. This work emphasized TRISO and metallic SNF and waste streams because of the near-term anticipated operation of the Xe-100 and the Natrium reactors as advanced-reactor demonstrations. Preliminary information for the spent-fuel salts discharged from molten-salt reactors (MSRs) is also examined to provide a baseline for future efforts. All calculations and assumptions used publicly available information. The following characteristics are calculated or estimated for use in the preliminary assessments: SNF volume and mass, radiation/activity levels through time, thermal conditions through time, potential radionuclide source terms, chemical interactions and evolutions, disposal inventories, and waste-form lifetime. Using those characteristics, calculations to determine the applicability of existing canister designs were performed. These evaluations included geometric (e.g., dimension, volume) and mass/weight considerations, known operational approaches and loading procedures, physical and chemical considerations/conditions for storage environments, as-loaded radiation, thermal, and criticality analyses to identify constraints for storage, transportation, and disposal. The paper also includes a literature review and analysis on the storage, transportation, and disposal evaluations and experiences from reactors with similar fuel forms. Advanced-reactor vendors cite past experiences with Fort St. Vrain for TRISO and the Experimental Breeder Reactor II (EBR-II) for metallics that have major influences on fuel design. Finally, the paper includes preliminary concepts of operation for advanced-reactor SNF. This encompasses storage, transportation, potential treatment, and disposal activities from both a per-canister and systems-integration perspective.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel Jana Howard1,3, Guang Yang3, Haiyan Zhao1*, Patrick Warren4, Tiankai Yao3, Steven Cavazos4 Elizabeth Sooby Wood4*, Ching-heng Shiau2 1 University of Idaho, Environmental Science, Idaho Falls, Idaho, USA 2 Boise State University, Microscopy and Characterization Suite, Idaho Falls, Idaho, USA 3 Idaho National Laboratory, Idaho Falls, Idaho, USA 4 University of Texas San Antonio, Department of Physics and Astronomy, San Antonio, Texas, USA *Corresponding author: haiyanz@uidaho.edu; elizabeth.soobywood@utsa.edu Tri-structural Isotropic (TRISO) particle fuel is the preferred choice for the newest and next-generation high-temperature nuclear reactors due to its robust construction [1]. The fuel design effectively contains fission products inside the particle at extremely high temperatures [2]. However, the effect of transition metal fission products on fuel performance and structural integrity remains largely unknown, creating uncertainties in predicting fuel performance and potential failure mechanisms [2]. For example, palladium (Pd) has a strong tendency to form intermetallic phases with uranium (U). These new phases tend to be hard and brittle which could lead to fracture of fuel kernel during irradiation [3,4]. Pd is not normally produced in high concentrations in normal fission reactions however, driving the production of Pd into the locality of a Uranium Oxycarbide (UCO) nuclear fuel provides an opportunity to closely observe the diffusion and chemical interactions. This study focuses on detailed transmission electron microscopy characterization of the intermetallic phases formed by the interaction between a UCO kernel and a Pd bar after annealing at 1100 °C for 100 hours. Figure 1 provides an overview of the UCO kernel in contact with the Pd bar. The UCO-Pd sample surface was examined using a Focused Ion Beam (FIB) Quanta 3D FEG FEI in VCD detector mode at 10kV, 83pA to reveal surface features. Several key surface features in the interaction region were observed including: (1) a small area with dendritic microstructure, (2) color contrast near the UCO kernel and Pd boundary, and (3) darker and lighter regions throughout the sample surface. To analyze diffusion behavior, FIB was used to prepare lamellae from five different areas of the UCO-Pd sample, as well as one for the as-received sample. These lamellae were examined using a Scanning Transmission Electron Microscope ThermoFisher Spectra 300 (STEM-Spectra). Energy Dispersive Spectroscopy results confirmed the diffusion between the UCO fuel and Pd bar. Figure 2 shows the identified phases of UC, UO2, and Pd dispersed throughout the interaction region. It was also found that the Pd concentration decreases as the radial distance from the UCO-Pd interface increases. The Pd concentration was 36.93% atomic fraction 11µm from the interaction region then decreased to 7.51% atomic fraction at 257 µm away from the interaction region. Figure 3 shows how concentrations of U and Pd vary across the interaction zone, highlighting the extent of diffusion. This study confirms that Pd interacts with surrounding material to form U-Pd phase and diffusion zones. These diffusion zones vary in composition depending on its radial distance from the point of contact with the Pd bar. These findings contribute to a deeper understanding of the fission product behavior in high temperature nuclear fuels, aiding in the prediction and mitigation of potential fuel degradation mechanisms. A B C Fig. 1. SEM micrographs of UCO fuel kernel in contact with solid Pd bar and the lift out locations. Figure 1A shows UCO fuel kernel in contact with solid Pd bar. Figure 1B shows a higher magnification image of the UCO fuel-Pd interaction zone. Figure 1C shows lift out sites for the lamellae. A B C Fig 2. EDS maps reveal the distribution of U, O, and Pd in location 3. Figure 2A shows the distribution of uranium. Figure 2B shows the distribution of oxygen. Figure 2C shows the distribution of palladium. A B C Fig 3. Palladium and uranium concentration across interaction zone in location 2. Figure 3A shows EDS map of lift out number 2. Figure 3B shows a zoomed in EDS map taken from the interaction zone. Figure 3C shows a line graph of uranium and palladium concentrations across the interaction zone. References: 1. B.E. Wells, N.R. Phillips, K.J. Geelhood. Pacific West Laboratory. (2021). TRISO Fuel: Properties and Failure Modes. https://www.nrc.gov/docs/ML2117/ML21175A152.pdf (Accessed January 16, 2025). 2. American Nuclear Society. TRISO Fuel Development Progresses in INL, ORNL. https://www.gen-4.org/gif/upload/docs/application/pdf/2014-03/nov13nn_fuel_reprint.pdf (Accessed January 16, 2025) 3. Clark R.A., M.A. Con

36 - MATERIALS SCIENCE↗

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel Jana Howard1,3, Guang Yang3, Haiyan Zhao1*, Patrick Warren4, Tiankai Yao3, Steven Cavazos4 Elizabeth Sooby Wood4*, Ching-heng Shiau2 1 University of Idaho, Environmental Science, Idaho Falls, Idaho, USA 2 Boise State University, Microscopy and Characterization Suite, Idaho Falls, Idaho, USA 3 Idaho National Laboratory, Idaho Falls, Idaho, USA 4 University of Texas San Antonio, Department of Physics and Astronomy, San Antonio, Texas, USA *Corresponding author: haiyanz@uidaho.edu; elizabeth.soobywood@utsa.edu Tri-structural Isotropic (TRISO) particle fuel is the preferred choice for the newest and next-generation high-temperature nuclear reactors due to its robust construction [1]. The fuel design effectively contains fission products inside the particle at extremely high temperatures [2]. However, the effect of transition metal fission products on fuel performance and structural integrity remains largely unknown, creating uncertainties in predicting fuel performance and potential failure mechanisms [2]. For example, palladium (Pd) has a strong tendency to form intermetallic phases with uranium (U). These new phases tend to be hard and brittle which could lead to fracture of fuel kernel during irradiation [3,4]. Pd is not normally produced in high concentrations in normal fission reactions however, driving the production of Pd into the locality of a Uranium Oxycarbide (UCO) nuclear fuel provides an opportunity to closely observe the diffusion and chemical interactions. This study focuses on detailed transmission electron microscopy characterization of the intermetallic phases formed by the interaction between a UCO kernel and a Pd bar after annealing at 1100 °C for 100 hours. Figure 1 provides an overview of the UCO kernel in contact with the Pd bar. The UCO-Pd sample surface was examined using a Focused Ion Beam (FIB) Quanta 3D FEG FEI in VCD detector mode at 10kV, 83pA to reveal surface features. Several key surface features in the interaction region were observed including: (1) a small area with dendritic microstructure, (2) color contrast near the UCO kernel and Pd boundary, and (3) darker and lighter regions throughout the sample surface. To analyze diffusion behavior, FIB was used to prepare lamellae from five different areas of the UCO-Pd sample, as well as one for the as-received sample. These lamellae were examined using a Scanning Transmission Electron Microscope ThermoFisher Spectra 300 (STEM-Spectra). Energy Dispersive Spectroscopy results confirmed the diffusion between the UCO fuel and Pd bar. Figure 2 shows the identified phases of UC, UO2, and Pd dispersed throughout the interaction region. It was also found that the Pd concentration decreases as the radial distance from the UCO-Pd interface increases. The Pd concentration was 36.93% atomic fraction 11µm from the interaction region then decreased to 7.51% atomic fraction at 257 µm away from the interaction region. Figure 3 shows how concentrations of U and Pd vary across the interaction zone, highlighting the extent of diffusion. This study confirms that Pd interacts with surrounding material to form U-Pd phase and diffusion zones. These diffusion zones vary in composition depending on its radial distance from the point of contact with the Pd bar. These findings contribute to a deeper understanding of the fission product behavior in high temperature nuclear fuels, aiding in the prediction and mitigation of potential fuel degradation mechanisms. A B C Fig. 1. SEM micrographs of UCO fuel kernel in contact with solid Pd bar and the lift out locations. Figure 1A shows UCO fuel kernel in contact with solid Pd bar. Figure 1B shows a higher magnification image of the UCO fuel-Pd interaction zone. Figure 1C shows lift out sites for the lamellae. A B C Fig 2. EDS maps reveal the distribution of U, O, and Pd in location 3. Figure 2A shows the distribution of uranium. Figure 2B shows the distribution of oxygen. Figure 2C shows the distribution of palladium. A B C Fig 3. Palladium and uranium concentration across interaction zone in location 2. Figure 3A shows EDS map of lift out number 2. Figure 3B shows a zoomed in EDS map taken from the interaction zone. Figure 3C shows a line graph of uranium and palladium concentrations across the interaction zone. References: 1. B.E. Wells, N.R. Phillips, K.J. Geelhood. Pacific West Laboratory. (2021). TRISO Fuel: Properties and Failure Modes. https://www.nrc.gov/docs/ML2117/ML21175A152.pdf (Accessed January 16, 2025). 2. American Nuclear Society. TRISO Fuel Development Progresses in INL, ORNL. https://www.gen-4.org/gif/upload/docs/application/pdf/2014-03/nov13nn_fuel_reprint.pdf (Accessed January 16, 2025) 3. Clark R.A., M.A. Con

36 - MATERIALS SCIENCE↗

A Machine Learning Approach Toward Improving QA/QC of Coated Particle Fuels

Coated particle fuels, such as the tristructural isotropic (TRISO) fuel particle, have been studied and developed for decades for high-temperature gas reactor (HTGR) applications because of their efficiency and relative stability under off-normal conditions. Critical to this development is a strong understanding of the relationship between fuel fabrication, properties and performance, as is how the former can be adjusted and improved to optimize the latter. Accordingly, wide-scale implementation of coated nuclear particle fuels requires thorough and robust quality assurance/quality control (QA/QC) methods for fabrication, characterization, and deployment

Conry, Bryan [ORNL] (ORCID:0000000236089604)↗

Physicochemical evolution of uranium nitride kernel microstructure with varying carbon distribution for advanced TRISO fuel forms

Uranium nitride (UN) has emerged as a fuel candidate for advanced nuclear reactor concepts due to its superior uranium density, thermal conductivity, and high melting temperature. However, the fabrication route for converting UO 2 to UN is complex and difficult to standardize. Although the chemistry of this conversion process is well-studied, more insight into the physicochemical dynamics of this conversion using advanced characterization techniques can help further our understanding of this material system. This work leveraged thermogravimetric analysis (TGA), X-ray diffraction (XRD), and nondestructive 3D X-ray computed tomography (XCT) to characterize dynamic microstructural changes in the UO 2 → UCO → UN fabrication pathway for two kernels with a varying carbon distribution in the starting composition. TGA and XRD were used to quantify changes in the mass, density, and chemical composition of the two kernels, while three-dimensional image processing and segmentation of XCT data were used to quantify the volume, surface area, and spatial distribution of features within each kernel for multiple steps along the fabrication pathway. The analysis indicates distinct differences between the two kernels that are correlated to downstream conversion efficiency. In conclusion, this work is among the first to perform 3D quantification of physicochemical evolution during UN conversion, providing quantitative correlation between processing, properties, and expected fuel performance.

Nuclear fuel↗

Bison Analyses of Fuel Forms used in Small Modular Reactors

Small Modular Reactors (SMRs) are actively being pursued by the international nuclear industry. The Bison fuel performance code developed at Idaho National Laboratory is a tool capable of analyzing the thermo-mechanical response and species diffusion for a wide variety of fuel types under both normal and accident conditions. Two of the fuel types considered for a wide range of SMRs are TRISO fuel particles and metallic fuel. This paper provides an overview of the capabilities in Bison for these fuel types with a few example studies relevant for the SMR industry.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Conceptual Design Report for the Xe-6/7/8 Experiment in the NE Flux Trap

X energy, LLC has initiated conceptual design of a high-temperature, pebble-bed reactor and requested that Idaho National Laboratory evaluate the feasibility of irradiating several fuel pebbles in the Advanced Test Reactor. The proposed fuel for the X energy reactor utilizes the same tristructural-isotropic coated fuel particles as are used in the Department of Energy-sponsored Advanced Gas Reactor (AGR) fuel tests, which have been irradiated in the ATR since 2006. The X energy test has been denoted XE 6/7/8 based on nomenclature from the AGR fuel-test series. Three tests will be combined into one test train: XE 6 constitutes the fuel qualification test, whose aim is to demonstrate fuel performance at the upper end of prototypical reactor conditions; XE 7 is designated a “margin test,” and its purpose is to demonstrate fuel integrity at conditions substantially beyond reactor operating conditions; and XE 8 incorporates designed-to-fail particles in order to release fission products and help validate fission product release codes. The XE series of experiments would consist of multiple separate capsules that would be irradiated simultaneously. Each capsule would have its own inert sweep-gas atmosphere with individual on line temperature monitoring. The sweep-gas effluent from each capsule would also have online fission product monitoring to track performance of the fuel in each individual capsule during irradiation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Measurement of Fission Product Concentration Profiles in AGR-3/4 TRISO Fuel Graphitic Matrix and Nuclear Graphites

The third Advanced Gas Reactor (AGR) irradiation experiment, AGR-3/4, was designed to investigate the migration of fission products in fuel compact graphitic matrix and reactor graphite components. Using destructive methods, radial fission product concentration profiles were measured for gamma-emitting fission products (e.g., Ag-110m, Cs-134, and Eu-154) and beta-emitting Sr-90 in irradiated graphitic and graphite components from six different AGR-3/4 irradiation capsules. These new measured concentration profiles can now be compared to non-destructive measurements and fission product transport simulations and will be used to derive new diffusivities and sorptivities to support refinement of fission product transport models and high-temperature gas-cooled reactor (HTGR) source-term analyses. Each capsule in the AGR-3/4 experiment had four fuel compacts in the middle of two concentric rings of graphitic matrix material, PCEA graphite, or IG-110 graphite. In addition to the approximately 1898 tristructural isotropic (TRISO) coated particles in each compact, there were 20 designed to fail (DTF) particles coated only in pyrocarbon so that they released fission products into the surrounding cylindrical rings of carbonaceous materials. Destructive sampling of the rings involved machining/milling material from around the circumference of the rings, collecting that material, and performing radiochemical analyses on it. Milling operations were performed in multiple steps or segments, and each segment was generally 0.508 mm (0.020 in) thick. Knowing the radial position at which each segment was milled, the volume of the milled material at each segment, and the fission product content in each segment, the radial fission product concentrations were constructed for select isotopes in each ring. Ag-110m profiles had the most variation. Some profiles were peaked at an inner or outer surface. Some were peaked at the middle of the ring wall thickness. Some increased radially outward, and some decreased radially outward. These types of variations and the fact that the measured profiles do not generally compare favorably with the transport model employed for AGR-3/4 may adversely impact the ability to extract reasonable transport parameters for this isotope. In many cases, the Cs-134 profiles decreased somewhat linearly in the outward radial direction, and in cursory comparisons, the shapes of these profiles appeared similar to those from model predictions. The step changes in concentration across the inner-outer ring gap were generally consistent with the model predictions as well. In some cases, there were local maxima in concentration at the outer surface of the rings. This suggests that fission products could have transported in the small gaps between the inner ring and the outer ring and between the outer ring and the sink ring such that some portion of a given fission product can bypass diffusion through the ring itself. The analysis of the small nubs on the outer surfaces of some of the outer rings revealed fission product concentrations in the nubs that were often higher than in the outermost segments of the rings. This further supports the hypothesis that short-circuit, gap transport occurred, causing relatively high surface concentrations on the outer surfaces of the rings. Eu-154 and Sr-90 profiles tend to have very similar shapes, suggesting that they transport via the same mechanisms. The observed profiles were indicative of a transport process where the isotopes are sorbed on the inner surface of the ring, but diffusion into the ring from that surface is quite slow. Some elevated concentrations of Sr-90 (relative to Eu-154) on the outer surface of a ring suggested that rapid, gas-gap transport of gaseous precursor Kr-90 and volatile Rb-90 could have occurred prior to their decaying to Sr-90. Overall, the Eu 154 and Sr-90 profiles were still very similar, which indicates that the transport of short-lived Sr-90 precursors is not a major effect. In some capsules, the qualitative Sr-90 behavior across the ring gaps was consistent with the model (using the available legacy Sr-90 transport parameters), but in other capsules the model was inconsistent with the measurements and seems to underestimate the amount of Sr-90 in the outer rings. The total ring Sr-90 inventories were estimated for all the rings that were subject to physical sampling. These results will be used to adjust the predicted particle and/or compact releases used in the AGR-3/4 fission product transport model. Given the different irradiation temperatures among the capsules and the rings, it was not possible to discern fundamental differences in the transport of isotopes within the different carbon materials, i.e., graphitic matrix, IG-110, or PCEA. It may be possible to do this in the course of determining transport from the concentration profiles in future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Updated NGNP Fuel Acquisition Strategy

A Next Generation Nuclear Plant (NGNP) fuel acquisition strategy was first established in 2007. In that report, a detailed technical assessment of potential fuel vendors for the first core of NGNP was conducted by an independent group of international experts based on input from the three major reactor vendor teams. Part of the assessment included an evaluation of the credibility of each option, along with a cost and schedule to implement each strategy compared with the schedule and throughput needs of the NGNP project. While credible options were identified based on the conditions in place at the time, many changes in the assumptions underlying the strategy and in externalities that have occurred in the interim requiring that the options be re-evaluated. This document presents an update to that strategy based on current capabilities for fuel fabrication as well as fuel performance and qualification testing worldwide. In light of the recent Pebble Bed Modular Reactor (PBMR) project closure, the Advanced Gas Reactor (AGR) fuel development and qualification program needs to support both pebble and prismatic options under the NGNP project. A number of assumptions were established that formed a context for the evaluation. Of these, the most important are: • Based on logistics associated with the on-going engineering design activities, vendor teams would start preliminary design in October 2012 and complete in May 2014. A decision on reactor type will be made following preliminary design, with the decision process assumed to be completed in January 2015. Thus, no fuel decision (pebble or prismatic) will be made in the near term. • Activities necessary for both pebble and prismatic fuel qualification will be conducted in parallel until a fuel form selection is made. As such, process development, fuel fabrication, irradiation, and testing for pebble and prismatic options should not negatively influence each other during the period prior to a decision on reactor type. • Additional funding will be made available beginning in fiscal year (FY) 2012 to support pebble bed fuel fabrication process development and fuel testing while maintaining the prismatic fuel schedule. Options for fuel fabrication for prismatic and pebble bed were evaluated based on the credibility of each option, along with a cost and schedule to implement each strategy. The sole prismatic option is Babcock and Wilcox (B&W) producing uranium oxycarbide (UCO) tristructural-isotropic (TRISO) fuel particles in compacts. This option finishes in the middle of 2022 . Options for the pebble bed are Nuclear Fuel Industries (NFI) in Japan producing uranium dioxide (UO2) TRISO fuel particles, and/or B&W producing UCO or UO2 TRISO fuel particles. All pebble options finish in mid to late 2022.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Use of spectral shift to greatly improve uranium utilisation in FHR designs

Fluoride-salt-cooled high-temperature reactors (FHRs) are thermal-spectrum nuclear reactors defined by their use of liquid-fluoride-salt coolants, together with tri-isotropic (TRISO)-coated particle fuels and graphite moderator materials (Forsberg, 2004). FHRs are also characterized by their improved thermodynamic efficiency relative to gas-cooled reactors. The liquid salt coolant is designed to operate with high core outlet temperature and nearly atmosphere pressure. These features allow the FHR to possess higher core power density compared to gas-cooled TRISO-based systems. However, industry fabrication limitations result in a low volumetric fraction of fuel kernel in TRISO particles. In order to obtain reasonable operation periods, the enrichment needs to be in the high LEU (low enriched uranium) range as was proposed in the original design (Greene, 2010). Recent studies (Ilas, 2014) presented newly repurposed SmAHTR-CTC reactor concept that relies on prior experience obtained from the 2010 initial SmAHTR design (Greene, 2010). This design consists of 19 hexagonal fuel assemblies arranged in a 3-ring hexagonal geometry with 18 fuel plates each. The active length of fuel plates in each fuel assembly is 4 meters. The proposed SmAHTR-CTC achieves substantial improvements from the neutronic performance standpoint over the original concept. The results indicate that a fuel cycle length of over two years with discharged fuel burnup of 40 gigawatt-day per metric ton of initial heavy metal (HM) is possible with an 8% fuel enrichment in a once-through fuel cycle. However, the lower uranium enrichment loading requires a more frequent refueling strategy and hence considerably reduces the cycle length. It is necessary to achieve reasonable cycle length values but at the same time to extend the residence time of the fuel, especially since the costs associated with TRISO-fuel are substantially higher (Shropshire et al., 2008) than traditional UO{sub 2} fuel ($10,000/kg for TRISO vs $200/kg for UO{sub 2}). This paper presents an approach to extend the operational time and improve fuel utilization of FHR by means of spectral shift control. This is achieved by incorporating movable graphite structures into the design, instead of the static graphite blocks presently envisaged. At beginning of life (BOL), the graphite structures are withdrawn. The reactor is under-moderated, with excess neutrons being primarily captured in {sup 238}U, breeding {sup 239}Pu. Towards the end of life (EOL), the graphite structures are inserted, thermalizing the neutron spectrum and increasing reactivity. The extra {sup 239}Pu bred during the cycle is then burned, allowing the cycle and discharge burnup to be extended. Such movable structures regime should be feasible from an engineering point of view, given that it is broadly equivalent to inserting and withdrawing control rods. The preliminary results indicate that such a design may considerably improve the fuel utilization.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Other Power Reactor Fuels

While oxide fuels have received the bulk of historic interest as power reactor fuels, a range of other uranium compounds and deployment architectures have also been considered and demonstrated to varying degrees. Metal alloys, technical ceramics, and oxycarbide or oxynitride particle fuels are candidates for various power reactor applications. Although in general these families of nuclear fuels have received more limited study than oxides, the benefits of uranium density, favorable thermophysical properties, and other factors have resulted in interest from both the traditional nuclear power industry as well as more recent entrepreneurial efforts. The dominant fuel chemistry issues for these fuel forms differ substantially from those of oxide systems. Synthesis routes, factors that affect fresh fuel properties, and critical aspects of fuel performance are unique to these systems and often dominated by the desired chemical behavior of uranium in each system. This chapter will briefly introduce metallic uranium alloys, specifically uranium-zirconium, non-traditional ceramic fuels such as carbides and nitrides, and oxycarbide/oxynitride particle fuels most familiar as the basis for TRISO fuel designs. A survey of major fuel chemistry issues is provided for each of these families of fuels, with a focus on contemporary challenges and active research avenues.

Nelson, Andrew↗

Irradiated AGR-2 Compact 3-1-1 Examination Plan

This plan describes post-irradiation examination (PIE) activities (safety testing and post-safety test analyses) to be performed by Oak Ridge National Laboratory (ORNL) on irradiated Compact 3-1-1 taken from the Advanced Gas Reactor (AGR) experiment, AGR 2. This work will be performed in accordance with general objectives outlined in the AGR-2 PIE plan and guidance in the ORNL PIE statement of work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗