SEARCH · Engineering Papers
Results for “Structured cathode”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Comment on the mechanism of operation of the impregnated tungsten cathode
Recent life-test measurements, over 20,000-30,000 h, on impregnated tungsten cathodes in tubes employing an open-type electron-gun structure, show emission current degradation with time. This is in contrast to those recently published by Rittner on B-type cathodes, run in close-spaced diodes, taken some years ago. These more recent life-test results are consistent with the model suggested by Forman and disputed by Rittner that the barium coverage on an impregnated cathode is less than a monolayer for most of its life and decreases with time.
Modulating Surface Anionic Redox Chemistry toward Highly Stable Li-Rich Cathodes with Negligible Oxygen Loss
Low initial Coulombic efficiency and severe capacity/voltage fading during cycling caused by serious irreversible oxygen release, especially in the initial cycle, and resultantly induced unstable electrode/electrolyte interfacial chemistry, largely prohibit the commercial application of high-capacity Li-rich layered oxide cathodes (LLOs). Here, in this work, a dual reductive gas interface cotreatment strategy is applied to regulate the lattice oxygen redox activity and reversibility with a multiple defective structure design including Li/O/TM (TM = transition metal) vacancies and the intrinsic TM doping as well as a full-surface protective layer, which can suppress the irreversible TM migration and then undesirable phase transformation, resisting the corrosion of electrolyte during cycling effectively. Importantly, the introduced reversible SO 3 2- /SO 4 2- redox couple that provides extra capacity compensation could alleviate the distortion of oxygen-central octahedral structure and structural collapse caused by immoderate oxygen oxidation. Thus, the lattice oxygen redox chemistry is optimized, with negligible oxygen loss during the initial cycle. And the designed AS-LLO cathode with greatly enhanced structure stability shows high-capacity retentions of 99.2% at 0.3C after 100 cycles and 82.4% even after 1000 cycles at 5C. This work provides a guideline for manipulating the oxygen redox chemistry to achieve long-lifespan Li-rich layered oxide cathodes for high-energy-density lithium batteries.
Deciphering the morphology of transition metal carbonate cathode precursors
The performance and life of Li-ion battery cathode materials are determined by both the composition (crystal structure and transition metal ratio) and the morphology (particle size, size distribution, and surface area). Careful control of these two aspects is the key to long lasting, high-energy batteries that can undergo fast charge. Developing such cathodes requires manipulation of the synthesis conditions, namely the coprecipitation process to develop the precursor and a calcination step to lithiate and convert it to a transition metal oxide. In this paper, we utilize a combination of controlled synthesis, microscopic and spectroscopic characterization, and multi-scale mathematical modeling to shed light on the synthesis of cathode precursors. The complex interplay between the various chemical reactions in the co-precipitation process is studied to provide experimentalists with guidance on achieving composition control during synthesis. Further, the formation of a variety of morphologies of the primary particles and the driving force for agglomeration is mathematically described, for the first time, based on an energy minimization approach. Results suggest that the presence of Ni and/or Co significantly lowers the reaction rate constant compared to Mn, resulting in agglomerated growth in the former and single crystal growth in the latter. Modeling studies are used to provide a phase map describing the synthesis conditions needed to control the secondary particle size and corresponding size distribution. Finally, this paper represents an important step in developing a computationally guided approach to the synthesis of battery cathode materials.
12Cao-7Al2o3 Electride Hollow Cathode
The use of the electride form of 12CaO-7Al.sub.2O.sub.3, or C12A7, as a low work function electron emitter in a hollow cathode discharge apparatus is described. No heater is required to initiate operation of the present cathode, as is necessary for traditional hollow cathode devices. Because C12A7 has a fully oxidized lattice structure, exposure to oxygen does not degrade the electride. The electride was surrounded by a graphite liner since it was found that the C12A7 electride converts to it's eutectic (CA+C3A) form when heated (through natural hollow cathode operation) in a metal tube.
12CaO-7Al2O3 Electride Hollow Cathode
The use of the electride form of 12CaO-7Al2O3, or C12A7, as a low work function electron emitter in a hollow cathode discharge apparatus is described. No heater is required to initiate operation of the present cathode, as is necessary for traditional hollow cathode devices. Because C12A7 has a fully oxidized lattice structure, exposure to oxygen does not degrade the electride. The electride was surrounded by a graphite liner since it was found that the C12A7 electride converts to it's eutectic (CA+C3A) form when heated (through natural hollow cathode operation) in a metal tube.
3D Printed, Low Tortuosity Garnet Framework For Beyond 500 Wh/kg Batteries
In this project, we developed LLZO garnet ink recipes and processes for 3D-printing highly ordered ionically conductive garnet porous structures on dense garnet separators. Using this technique, we are able to fabricate controlled architecture LLZO garnet solid-state electrolyte (SSE) trilayers for application in solid-state lithium batteries. The trilayer comprises a thin dense center layer sandwiched between a 3D-printed patterned porous layer and a random porous layer. The dense layer functions as the ionic separator between the anode and cathode. The random porous layer hosts the lithium-metal anode and provides the structural support. The 3D-printed SSE patterned porous layer hosts the cathode, providing continuous, low tortuosity pathways for fast 3D Li+ transport through the cell while increasing the electrode/electrolyte interface area to decrease the interfacial resistance. Compared to the random porous structure, this ordered patterned structure possesses more vacant space for higher cathode loading without sacrificing ionically conducting capability, thus potentially greatly increasing the cell energy density. For demonstration purposes, we developed two patterns for the 3D-printed porous layer: grids and columns, for hosting sulfur and NMC cathode, respectively. The corresponding two types of cells were fabricated and tested, and have demonstrated achievement of theoretical discharge capacity without cathode calendaring. In addition, we developed a fundamental solid-state ionic and electronic transport model to optimize the 3D-printed structures for maximum energy and power density. The model was validated by experiment and provides the critical design criteria for achieving the >500 Wh/kg energy goal as function of C-rate.
Direct recycling of spent nickel-rich cathodes in reciprocal ternary molten salts
Lithium-ion batteries (LIBs) have revolutionized portable electronics and electric vehicles (EVs), but the growing accumulation of end-of-life (EOL) batteries poses environmental challenges. Recycling high-value cathodes from EOL LIBs can minimize waste and reduce the need for mining critical minerals. Here, this study focuses on the direct recycling of Ni-rich cathodes, particularly lithium-manganese-cobalt-oxide (NMC) 622 in a “reciprocal ternary molten salts (RTMS)" system. The ionothermal relithiation in the RTMS system successfully restores the layered structure, lithium content, and electrochemical performance of the NMC 622 cathode, comparable to the pristine material. The cost analysis reveals that cathode regeneration through ionothermal relithiation is more economical than virgin production or conventional recycling methods.
Mechanistic Study of the Li–Air Battery with a Co 3 O 4 Cathode and Dimethyl Sulfoxide Electrolyte
The lithium–air battery, a powerful competitor to replace the traditional lithium-ion battery, has attracted increasing attention due to its extremely high theoretical energy density. However, its development is limited by the cathode and electrolyte properties, which should include high stability, conductivity, and electrocatalytic properties in oxygen-rich environments. Here, we employ a systematic first-principles study of Li–O 2 discharge and charge reactions on the Co 3 O 4 -based cathode with the assistance of dimethyl sulfoxide (DMSO) electrolyte. The structure, stability, and electronic properties of different surface reconstructions of the Co 3 O 4 (100) facet are investigated. In addition, the mechanisms and thermodynamic overpotentials of multi-step reactions between Li + /e – and O 2 are provided, where lithium suboxide products (Li 2 O 2 or Li 3 O 2 ) are formed on the different Co 3 O 4 (100) terminations. The solvation shell of Li + components in explicit DMSO solvent is investigated through ab initio molecular dynamics simulations. In general, we find that the Co 3 O 4 (100)-O (oxidized) surface is the most stable one under standard conditions, and the stable Li + solvation structure is found in a tetrahedral Li(DMSO) 4 + shell in the DMSO-based electrolyte. Moreover, in the system of the Co 3 O 4 (100)-O cathode and DMSO electrolyte, the solution model pathway is energetically favorable for the Li–O 2 discharge reaction. It provides a low constant overpotential of 0.17 V during a long-term discharging process, thus causing the final toroid Li 2 O 2 formation on the cathode. During the charging process, an overpotential of 0.36 V is required to rapidly decompose Li 2 O 2 .
Valuation of Surface Coatings in High-Energy Density Lithium-ion Battery Cathode Materials
Artificial barriers, usually with either electrochemically active or inactive coating materials, are deployed on cathode material surfaces to mitigate detrimental side reactions by suppressing direct contact of cathode and electrolyte called surface coatings. These surface coatings are commonly known to increase the wettability of liquid electrolyte and reduce the interfacial charge transfer resistance. An important caveat is the selection of appropriate coating material with appropriate thickness for achieving enhanced electrochemical performance. As modern battery materials are increasingly developed with some type of surface coating, a careful and thorough examination of their role in mitigating the cycle life issues of cathode materials is paramount. Here, this comprehensive review article extensively covers the selection criteria of coating materials based on their chemical and physical properties and electrochemical functionalities. Additionally, the article discusses the concept of critical coating thickness and methods of achieving homogeneous coating architectures that deliver desired performance benefits. Furthermore, this comprehensive article summarizes the recent advancements, effectiveness, necessity of cathode surface coatings and identifies the key aspect of structure-property correlation between coating type/thickness and lithium-ion diffusion through coating layers as the linchpin that validates surface coating approaches especially for high capacity nickel-rich cathodes.
Distinct Surface and Bulk Thermal Behaviors of LiNi 0.6 Mn 0.2 Co 0.2 O 2 Cathode Materials as a Function of State of Charge
Understanding how structural and chemical transformations take place in particles under thermal conditions can inform designing thermally robust electrode materials. Such a study necessitates the use of diagnostic techniques that are capable of probing the transformations at multiple length scales and at different states of charge (SOC). In this study, the thermal behavior ofLiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC-622) was examined as a function of SOC, using an array of bulk and surface-sensitive techniques. In general, thermal stability decreases as lithium content is lowered and conversion in the bulk to progressively reduced metal oxides (spinels, rock salt) occurs as the temperature is raised. Hard X-ray absorption spectroscopy (XAS) and X-ray Raman spectroscopy (XRS) experiments, which probe the bulk, reveal that Ni and Co are eventually reduced when partially delithiated samples (regardless of the SOC) are heated, although Mn is not. Surface-sensitive synchrotron techniques, such as soft XAS and transmission X-ray microscopy (TXM), however, reveal that for 50% delithiated samples, apparent oxidation of nickel occurs at particle surfaces under some circumstances. This is partially compensated by reduction of cobalt but may also be a consequence of redistribution of lithium ions upon heating. TXM results indicate the movement of reduced nickel ions into particle interiors or oxidized nickel ions to the surface or both. These experiments illustrate the complexity of the thermal behavior of NMC cathode materials. The study also informs the importance of investigating the surface and bulk difference as a function of SOC when studying the thermal behaviors of battery materials.
Chemical Modulation of Local Transition Metal Environment Enables Reversible Oxygen Redox in Mn-Based Layered Cathodes
Oxygen redox plays a prominent role in enhancing the energy density of Mn-based layered cathodes. However, understanding the factors affecting the reversibility of oxygen redox is nontrivial due to complicated structural and chemical transformations. Here in this paper, we show that local Mn–O symmetry induced structural/chemical evolutions majorly dictate the reversibility of oxygen redox of Na x Li y Mn 1–y O 2 in Na cells. Na x Li y Mn 1–y O 2 with Jahn–Teller distorted MnO 6 octahedra undergoes severe Mn dissolution during cycling, which destabilizes the transition metal layer resulting in poor Li retention and irreversible oxygen redox. Jahn–Teller distortion of MnO 6 octahedra can be suppressed by modulating the local charge of Mn and Mn–O distance through Mg/Ti dual doping. This leads to reduced Mn dissolution and more reversible oxygen redox. Such stabilization significantly improves the electrochemical performance of Mg/Ti dual doped Na x Li y Mn 1–y O 2 . Through this work, we show that local structural stabilization through local chemical environment modification can promote reversible oxygen redox in layered cathodes.
Correlating the Morphological Changes to Electrochemical Performance During Carbon Corrosion in Polymer Electrolyte Fuel Cells
A mechanistic understanding of carbon corrosion in polymer electrolyte fuel cells (PEFCs) is required to design durable catalyst layers. Uncontrolled startup and shutdown of PEFCs cause electrochemical oxidation of carbon, which leads to several degradation phenomena, such as loss in electrochemical surface area (ECSA), pore structure collapse or increase in mass transport resistance. In this study, the chronology of morphological changes in the cathode catalyst layer due to carbon corrosion was identified and correlated with electrochemical performance degradation. PEFCs were subjected to the Department of Energy carbon corrosion accelerated stress test (AST) protocol. The study revealed two phases: in the initial phase (~500 AST cycles), amorphous carbon in contact with Pt nanoparticles oxidized fast. Rapid carbon loss and catalyst layer thinning occurred, but pore structure did not change significantly. Pt nanoparticles detached from the support and ECSA decreased drastically. In the second phase (~1500 AST cycles), carbon corrosion slowed down, but severe pore structure collapse was observed. Porosity and pore connectivity within the cathode catalyst layer decreased considerably. Electrochemical diagnostics corroborated this finding by showing significantly higher O2 mass transport resistance. Lastly, no significant change was observed in the concentration of oxides on the carbon surface after AST. But overall water management in the cathode catalyst layer deteriorated as the pore structure collapsed. This study provides an in-depth understanding of morphological changes during PEFC carbon corrosion AST protocol and motivates novel material design strategies to enable durable PEFCs.
Coherent Strain-Inhibiting Phase Construction of Lithium-Rich Manganese-Based Oxide Toward High Mechanochemical Stability
A layered lithium-rich manganese-based oxide cathode, containing $R\overline{3}m$ (LiTMO 2 , TM = Mn, Ni, Co) and $C2/m$ (Li 2 MnO 3 ) nanodomains, utilizes both transition metals and oxygen redox to yield substantial energy density. However, the inherent heterogeneous nature and distinct nanodomain redox chemistries of layered lithium-rich oxides will inevitably cause pernicious lattice strain and structural displacement, which can hardly be eliminated by conventional doping or coating strategies and result in accelerated performance decay. Herein, we incorporate a strain-inhibiting perovskite phase coherently grown within the layered structure to effectively restrain the displacement and lattice strain during uneven Li-ion extraction. The enhanced mechanochemical stability of the designed cathode benefits the persistent structure and reversible oxygen redox, thereby achieving high initial Coulombic efficiency and stable cycling and voltage profiles. In conclusion, our approach of lattice engineering alleviates the strain and displacement caused by inhomogeneous reactivity between heterogeneous nanodomains and promotes the development of advanced cathode materials with long durability.
Enabling High Stability of Co-Free LiNiO 2 Cathode via a Sulfide-Enriched Cathode Electrolyte Interface
Cobalt-free lithium nickel oxide (LNO) has garnered significant interest as the end member of high-nickel layered oxide cathodes for next-generation batteries. However, its practical performance notably underperforms expectations because of the structural degradation and unstable interfacial chemistry with electrolytes during cycling. Here, in this study, we report that a durable cathode-electrolyte interface (CEI), enriched by in situ formed sulfides and borides, can inhibit LNO structural degradation and suppress Ni ion dissolution. With the CEI protection, the stability of LNO can be remarkably extended, and batteries demonstrate a capacity retention rate of 84% (30 °C) and 79% (50 °C) after 200 cycles at 1C, respectively. These results demonstrate that enriching CEI with sulfur-containing species can effectively stabilize the interfacial chemistry of LNO, particularly at an elevated temperature of 50 °C. This finding provides valuable perspectives on designing electrolytes for cobalt-free LNO and other high-Ni cathodes toward the development of next-generation high-energy-density lithium-ion batteries.
Redox-homogeneous, gel electrolyte-embedded high-mass-loading cathodes for high-energy lithium metal batteries
Lithium metal batteries have higher theoretical energy than their Li-ion counterparts, where graphite is used at the anode. However, one of the main stumbling blocks in developing practical Li metal batteries is the lack of cathodes with high-mass-loading capable of delivering highly reversible redox reactions. To overcome this issue, here we report an electrode structure that incorporates a UV-cured non-aqueous gel electrolyte and a cathode where the LiNi 0.8 Co 0.1 Mn 0.1 O 2 active material is contained in an electron-conductive matrix produced via simultaneous electrospinning and electrospraying. This peculiar structure prevents the solvent-drying-triggered non-uniform distribution of electrode components and shortens the time for cell aging while improving the overall redox homogeneity. Moreover, the electron-conductive matrix eliminates the use of the metal current collector. When a cathode with a mass loading of 60 mg cm -2 is coupled with a 100 µm thick Li metal electrode using additional non-aqueous fluorinated electrolyte solution in lab-scale pouch cell configuration, a specific energy and energy density of 321 Wh kg -1 and 772 Wh L -1 (based on the total mass of the cell), respectively, can be delivered in the initial cycle at 0.1 C (i.e., 1.2 mA cm -2 ) and 25 °C.
Multiprincipal Component P2-Na 0.6 (Ti 0.2 Mn 0.2 Co 0.2 Ni 0.2 Ru 0.2 )O 2 as a High-Rate Cathode for Sodium-Ion Batteries
Mixing transition metal cations in nearly equiatomic proportions in layered oxide cathode materials is a new strategy for improving the performances of Na-ion batteries. The mixing of cations not only offers entropic stabilization of the crystal structure but also benefits the diffusion of Na ions with tuned diffusion activation energy barriers. In light of this strategy, a high-rate Na 0.6 (Ti 0.2 Mn 0.2 Co 0.2 Ni 0.2 Ru 0.2 )O 2 cathode was designed, synthesized, and investigated, combining graph-based deep learning calculations and complementary experimental characterizations. This new cathode material delivers high discharge capacities of 164 mA g –1 at 0.1 C and 68 mAh g –1 at a very high rate of 86 C, demonstrating an outstanding high rate capability. Ex situ and operando synchrotron X-ray diffraction were used to reveal the detailed structural evolution of the cathode upon cycling. Using the climbing-image nudged elastic-band calculation and Ab initio molecular dynamics simulations, we show that the optimal transition metal composition enables a percolating network of low barrier pathways for fast, macroscopic Na diffusion, resulting in the observed high rate performance.
First-principles study of the structures and redox mechanisms of Ni-rich lithium nickel manganese cobalt oxides
To reduce the cobalt (Co) content in lithium-ion batteries, Ni-rich (high-Ni) lithium nickel manganese cobalt oxides (NMC) are pursued as one of the next-generation cathode materials. However, there is still debate on the crystal and electronic structures of the baseline, LiNiO 2 . Density Functional Theory (DFT) calculations were performed to provide a theoretical understanding of Ni-rich NMC. First, it was found that the commonly used $R\bar{3}m$ structure for LiNiO 2 is metallic, contrary to the experimentally reported mix-conducting behavior. Among the four different space groups, $R\bar{3}m$, C2/m, P2 1 /c, and P2/c, P2/c with charge disproportionation of Ni 2+ and Ni 4+ is the most energetically stable and semiconducting structure of LiNiO 2 . Therefore, the atomic structures of representative Ni-rich NMC were built by partially replacing Ni with Co or Mn in the P2/c LiNiO 2 to form Li x Ni y Mn z Co 1-y-z O 2 . In the fully lithiated (x=1.0) high Ni content NMC (y>0.5), the oxidation state of all Mn ions becomes 4+, while Co ions still maintain 3+, and part of the Ni ions become 3+ to compensate for the charge. Upon delithiation, the local environment shows more variation of the charge states on the transition metal (TM) ions. The average oxidation on each TM follows a sequence of losing electrons that starts from Ni 2+ to Ni 3+ , then oxidizing Ni 3+ and Co 3+ , while Mn 4+ remains electrochemically inactive till x=0. Finally, a general relationship for the oxidation state change in each TM as a function of x is derived and shows agreement with both modeling and experimental data.