SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
As accreted material falls to the surface of a magnetized neutron star like Cen X-3 or Her X-1, it is arrested by radiation pressure in such a manner that a hot, dense mound of nearly stationary gas protrudes above each magnetic pole. Energy released above the mound diffuses out as moderately hard X rays; but that released within the mound emerges as soft X rays from the whole surface of the neutron star.
Designing optics for photometry in the long-wavelength portion of the EUV spectrum (400-900) A) poses different problems from those arising for optics, operating shortward of 400 A. The available filter materials which transmit radiation longward of 400 A are also highly transparent at wavelengths shortward of 100 A. Conventional EUV optics, with grazing engles of less than about 10 deg, have very high throughput in the EUV, which persists to wavelengths shortward of 100 A. Use of such optics with the longer-wavelength EUV filters thus results in an unacceptably large soft X-ray leak. This problem is overcome by developing a mirror design with larger graze angles of not less than 20 deg, which has high throughput at wavelengths longer than 400 A but at the same time very little throughput shortward of 100 A.
The spatial structure of the X-ray sky in the direction of the North Polar Spur was examined in two energy bands, the B band (0.10 to 0.18 keV) and the C band (0.15 to 0.28 keV). A model with two emitting regions, one local with unabsorbed emission, and the other more distant with emission partially absorbed by spatially varying amounts was investigated. Using the distribution of atomic hydrogen as a measure of absorbing material, this model was used to predict the flux in the direction of the North Polar Spur. The predicted flux was compared to the data obtained from several sounding rocket flights. The derived flux was found to correlate well with the observed data.
Direct X-ray observations allow us to estimate the hot coronal mass before and after a flare or other disturbance of the type leading to a coronal mass ejection. The sudden disappearance of a large coronal structure (scale greater than 105 km) gives evidence that an ejection has occurred, if the time scales are much shorter than the conductive or radiative cooling times for such structures. A flare also typically adds large amounts of new material to the corona via evaporation resulting from the coronal energy release. This provides a competing mechanism that makes the estimation of the total mass loss somewhat difficult. We note that the X-ray observations have the advantage of covering the entire corona rather than the limb regions unlike the coronagraph observations. We have identified two examples of coronal mass disappearances. before and during long duration flare events on 21 Feb. 1992 (on the E limb) and 13 Nov. 1994 (near disk center). In latter case the total mass amounted to some 4 x 10(exp 14) g with a density of 3 x 10(exp 8)cm(exp -3) and a temperature of 2.8 MK before its disappearance. This corresponds to a radiative cooling time of some 104 S. much longer than the observed time of disappearance. We therefore suggest that these sudden mass disappearances correspond with coronal mass ejections (CMEs), and suggest that further data analysis will be able to confirm this by comparison with optical observations of specific CMEs.
Room temperature vulcanizing (RTV) silicone is a high-temperature adhesive used as a gap-filler between heatshield tiles in numerous entry missions. Its propensity to intumesce, or swell upon exposure to heat, is a well-known effect that needs to be carefully quantified during design. At tile interfaces of charring ablators, intumescence, combined with differential recession, could cause the gap filler to protrude past the ablator outer mold line, forming a “fence”. Fencing can in turn cause transition to turbulence of the flow wetting the heat shield, leading to augmented surface heating. Recent experiments conducted at the Plasmatron X facility, the high enthalpy wind tunnel of the Center for Hypersonics and Entry Systems Studies, have shown prominent fencing of RTV gap fillers in PICA, under both nitrogen and air plasmas. Similar observations are well known in the arcjet literature. Further experiments under controlled environment, performed using in situ X-ray micro-computed tomography (micro-CT) at the Advanced Light Source (ALS), have shown heating rate-dependent swelling and shrinkage of RTV during pyrolysis. To simulate RTV intumescence, a novel model was introduced in the Porous Materials Analysis Toolbox based on OpenFOAM, PATO, to account for pore-pressure buildup within both closed- and open-pores. The governing equation for the thermo-poro-mechanical response were developed, assuming linear elasticity for the charring silicone. A new multi-pyrolysis model that tracks non-monotonic advancement of material properties with pyrolysis was proposed. This model addresses the limitations of state-of-the-art ablator models to capture the different stages of thermal degradation and coupled thermomechanics. Swelling of RTV was simulated using the new thermo-poro-mechanical model and compared against in situ micro-CT data. Results showed good agreement in intumescence height and temperature profiles at all heating rates, indicating that the key factor contributing to RTV swelling is the internal pressure build-up within closed- and open-pores. As RTV is cured into a soft (rubbery) compound with low-porosity and permeability, initial temperature increase and pyrolysis gas production cause a significant increase of internal pressure, causing a pronounced volume growth. As thermal degradation progresses, rigidization of the silicone occurs due to char hardening which counteract volume shrinkage after gas pressure relief. Overall, our model shows that accounting for changes in properties such porosity, permeability and key thermomechanical coefficients is crucial for capturing the RTV volume change during ablation and enable a predictive capability for heatshield tile interface response. A plan for future calibration of thermomechanical properties evolution during degradation is discussed, as a key next step to close the new model.
From the practical point of view, this analysis shows that each problem of friction or wear requires its particular solution. There is no universal solution; one or other of the factors predominates and defines the choice of the solution. In certain cases, copper alloys of great thermal conductivity are preferred; in others, plastics abundantly supplied with water. Sometimes, soft antifriction metals are desirable to distribute the load; at other times, hard metals with high resistance to abrasion or heat.
The scientific objective of the program was to better understand how CMEs (Coronal Mass Ejections) are initiated at the sun by examining structures on the disk which are related to the origins of CMEs. CMEs represent important disruptions of large-scale structures of closed magnetic fields in the corona, and result in significant disturbances of the interplanetary medium and near-Earth space. The program pertained to NASA's objectives of understanding the physics of solar activity and the structured and evolution of the corona, and the results are being applied to understanding CMEs currently being observed by SOHO near the sun and by WIND and Ulysses in the heliosphere. Three general areas of research were pursued in the program. One was to use Yohkoh soft X-ray telescope (SXT) images of eruptive events visible against the solar disk to examine the coronal structures and the boundaries of the large-scale magnetic fields considered to be involved in coronal mass ejections (CMEs). The second area involved a survey and study of SXT X-ray arcade events which exhibit dimming, or the possible depletion of coronal material above and possibly before onset of the bright long-duration event (LDE). Finally, we studied the SXT data during periods when white light CMEs were observed the HAO Mauna Loa K-coronameter and, conversely, we examined the white light data during periods when expanding X-ray loops were observed at the limb.
The continued search for organics on Mars will require the development of simplified procedures for handling and processing of soil or rock core samples prior to analysis by onboard instrumentation. Extraction of certain organic molecules such as amino acids from rock and soil samples using a liquid solvent (H2O) has been shown to be more efficient (by approximately an order of magnitude) than heat extraction methods. As such, liquid extraction (using H2O) of amino acid molecules from rock cores or regolith material is a prime candidate for the required processing. In this scenario, electrospray ionization (ESI) of the liquid extract would be a natural choice for ionization of the analyte prior to interrogation by one of a variety of potential analytical separation techniques (mass spectroscopy, ion mobility spectroscopy, etc.). Aside from the obvious compatibility of ESI and liquid samples, ESI offers simplicity and a soft ionization capability. In order to demonstrate that liquid extraction and ESI can work as part of an in situ instrument on Mars, we must better understand and quantify the effect salts have on the ESI process. In the current work, we have endeavored to investigate the feasibility and limitations of negative mode ESI of Martian surface samples in the context of sample salt content using ion mobility spectroscopy (IMS).
Fundamental to many of NASA's in-space transportation missions is the capture and handling of various objects and vehicles in various orbits for servicing, debris disposal, sample retrieval, and assembly without the benefit of sufficient grapple fixtures and docking ports. To perform similar material handling tasks on Earth, pincher grippers, suction grippers, or magnetic chucks are used, but are unable to reliably grip aluminum and composite spacecraft, insulation, radiators, solar arrays, or extra-terrestrial objects in the vacuum of outer space without dedicated handles in the right places. The electronic Flexible Electrostatic Technologies for space Capture and Handling (FETCH) will enable reliable and compliant gripping (soft dock) of practically any object in various orbits or surfaces without dedicated mechanical features, very low impact capture, and built-in proximity sensing without any conventional actuators. Originally developed to handle semiconductor and glass wafers during vacuum chamber processing without contamination, the normal rigid wafer handling chucks are replaced with thin metal foil segments laminated in flexible insulation driven by commercial off-the-shelf solid state, high-voltage power supplies. Preliminary testing in NASA Marshall Space Flight Center's (MSFC's) Flat Floor Robotics Lab demonstrated compliant alignment and gripping with a full-sized, 150-lb microsat mockup and translation before a clean release with a flip of a switch. The flexible electrostatic gripper pads can be adapted to various space applications with different sizes, shapes, and foil electrode layouts even with openings through the gripper pads for addition of guidance sensors or injection of permanent adhesives. With gripping forces estimated between 0.5 and 2.5 lb/in2 or 70-300 lb/ft2 of surface contact, the FETCH can turn on and off rapidly and repeatedly to enable sample handling, soft docking, in-space assembly, precision relocation, and surface translation for accurate anchoring.
Room temperature vulcanizing (RTV) silicone is a high-temperature adhesive used as a gap-filler between heatshield tiles in numerous entry missions. Its propensity to intumesce, or swell upon exposure to heat, is a well-known effect that needs to be carefully quantified during design. At tile interfaces of charring ablators, intumescence, combined with differential recession, could cause the gap filler to protrude past the ablator outer mold line, forming a “fence”. Fencing can in turn cause transition to turbulence of the flow wetting the heat shield, leading to augmented surface heating. Recent experiments conducted at the Plasmatron X facility, the high enthalpy wind tunnel of the Center for Hypersonics and Entry Systems Studies, have shown prominent fencing of RTV gap fillers in PICA, under both nitrogen and air plasmas. Similar observations are well known in the arcjet literature. Further experiments under controlled environment, performed using in situ X-ray micro-computed tomography (micro-CT) at the Advanced Light Source (ALS), have shown heating rate-dependent swelling and shrinkage of RTV during pyrolysis. To simulate RTV intumescence, a novel model was introduced in the Porous Materials Analysis Toolbox based on OpenFOAM, PATO, to account for pore-pressure buildup within both closed- and open-pores. The governing equation for the thermo-poro-mechanical response were developed, assuming linear elasticity for the charring silicone. A new multi-pyrolysis model that tracks non-monotonic advancement of material properties with pyrolysis was proposed. This model addresses the limitations of state-of-the-art ablator models to capture the different stages of thermal degradation and coupled thermomechanics. Swelling of RTV was simulated using the new thermo-poro-mechanical model and compared against in situ micro-CT data. Results showed good agreement in intumescence height and temperature profiles at all heating rates, indicating that the key factor contributing to RTV swelling is the internal pressure build-up within closed- and open-pores. As RTV is cured into a soft (rubbery) compound with low-porosity and permeability, initial temperature increase and pyrolysis gas production cause a significant increase of internal pressure, causing a pronounced volume growth. As thermal degradation progresses, rigidization of the silicone occurs due to char hardening which counteract volume shrinkage after gas pressure relief. Overall, our model shows that accounting for changes in properties such porosity, permeability and key thermomechanical coefficients is crucial for capturing the RTV volume change during ablation and enable a predictive capability for heatshield tile interface response. A plan for future calibration of thermomechanical properties evolution during degradation is discussed, as a key next step to close the new model.
The soft X-ray background (SXRB) surface brightness provides data to study the approximately 10(exp 6) K plasma of the local interstellar medium of our Galaxy. Various studies were carried out in order to search for negative correlation, or shadowing, of the SXRB, and were coupled with interstellar medium absorption line studies. The purpose was to determine whether the distances to the shadowing material will lead to a three dimensional mapping of the X-ray emitting, and X-ray absorbing components.
Understanding structure-property-process relationship aka rheology of regolith in varying gravity conditions is critical for exploration and future missions. In this work, a framework for studying rheology of lunar regolith simulant in varying gravity conditions (Terrestrial, Lunar and Martian) is described theoretically/numerically, where the driving force of flow of simulants was gravitational acceleration. In the analysis particle-particle interaction forces were included. It was found that the dynamic behavior of granular material is extremely sensitive to external conditions by virtue of the myriad of forces present between particle grains. The results obtained were validated against results obtained in earth and Lunar gravity conditions. The theoretical/numerical and experimental results showed that the complex interaction of these forces can drastically change the dynamics of the material, which is not captured by standard design rules, generally used in industry, for variable gravity applications.
Data from the 1989-1990 IUE monitoring of the Seyfert galaxy NGC 5548 are used here to analyze the continuum variability properties of the galaxy and to derive the structure or its emission-line region. The mean shape of the UV continuum is well fit by an accretion disk model with a given black hole mass and an additional component required to reproduce the observed soft X-ray flux. The continuum fluctuation power spectrum is very steep, with most of the variance coming from about 1 yr time scales. The entire optical/UV continuum rises and falls almost simultaneously, so that the logarithmic slope of the power spectrum is nearly the same for all bands, but the flux at higher photon frequencies varies with larger amplitude. The emission-line material around the nucleus may best be described by a highly ionized inner zone of high and nearly constant pressure that stretches about 4-14 light-days from the center and an outer, more weakly ionized zone of considerably lower ionization at least 20-30 light-days out.
Aquila Equine Enhancement Products, Inc., of Woburn, Massachusetts, developed magnetic hoof protector pads, called "Power Pads," which support and cushion the impact on a horse's hooves and legs to provide comfort and protection against injuries. The pads were tested by Marshall Space Flight Center's Materials and Processing Laboratory for strength and durability. Putting the pads on a horse does not interfere with its natural movement or flexibility and can be compared to a person changing into athletic shoes for a sporting event. The pads are cut to the appropriate size, and then mounted onto a horse's hooves using conventional shoeing methods. Once attached, the pads protect the hard and soft parts of the hoof by cushioning blows against the hard ground. The design also protects the vulnerable "heel" of the hoof. They are a cost-effective way to protect a horse's hooves since they can be reused.
Comets are primitive bodies that are widely believed to be a reservoir of preserved interstellar and circumstellar grains, and molecular cloud materials (organics). Direct samples of cometary dust along with interstellar grains will be returned by the STARDUST Mission in 2006. Analyses of interplanetary dust particles (IDPs) and analogue materials in the laboratory provide constraints and serve as "ground truth" for evaluating various hypotheses on the nature of comets and interstellar grains. Anhydrous IDPs are the most primitive remnants of the primordial Solar System, and are our only known samples of comets. These cometary lDPs are rich in preserved interstellar organic compounds II]. In addition, abundant interstellar silicates have recently been discovered in cluster lDPs [2]. In some of these IDPs, the presolar silicate abundance reaches 1 wt %, exceeding the total presolar grain abundance in meteorites by three orders of magnitude, where presolar silicates are still notably absent. The results to date support the idea that comets are rich in presolar materials, but are at odds with the common perception that they are 'pristine aggregates of interstellar grains'. These results underscore the scientific importance of sample return missions to comets. The technology for the analysis of micrometer-sized samples is well advanced. The newest generation of ion probe instruments allow for isotopic analyses at the submicrometer level. The nature of the organic matter is analyzed using Infrared and soft X-ray spectroscopy techniques on synchrotron-based instruments, also at the micrometer-scale and smaller. Electron microscopy and spectroscopy provide details on the mineralogy and chemistry of constituent grains in !DPs at nearly the atomic scale. Novel sample preparation techniques have been developed such that all of these measurements can now be made on the same 10 micrometer diameter particle. Returned comet samples captured in aerogel will pose new challenges in sample analysis, but should provide a major leap in our understanding of the fundamental building blocks of our Solar System.
The program to exploit unused NASA patents through the use of a multidisciplinary approach involving faculty students, and research staff is reported. NASA patents were screened for their applicability outside the space program, specific applications were identified, and the technical and commercial feasibility of these applications was established. Also application of this technology by governmental agencies outside the space program was sought. The program was specifically interested in energy absorbing devices such as those developed for lunar soft landings. These energy absorbing devices absorb large amounts of mechanical energy but are, in general, not reusable. Some of these devices can also operate as structural elements until their structural load capacity is exceeded and they become activated as energy absorbers. The capability of these devices to operate as structural elements and as energy absorbing devices makes them candidates for many applications in the fields of transportation and materials handling safety where accidents take a large toll in human injury and property damage.
A close temporal and spatial association has been found between erupting filaments/coronal transients and radio noise storm continua. The three transients studied occurred away from active regions and are members of a class not usually accompanied by chromospheric emission. The data analyzed were from the S-054 soft X-ray telescope on Skylab and from one- and two-dimensional interferometers at meter and decameter wavelengths at Nancay and Clark Lake observatories. Calculations confirmed that observed microwave radiation from the transients is due to thermal bremsstrahlung. The results are consistent with an interpretation of heating of an increased amount of coronal plasma by nonthermal, 10-100 keV electrons. Three possibilities for the source of the material are described: (1) the filament material; (2) evaporation from the chromosphere or transition region; and (3) via a long-lived reconnection process.
We observed the edge-on spiral galaxy NGC 891 with the Position Sensitive Proportional Counter (PSPC) on Roentgen Satellite (ROSAT) to search for how extraplanar gas expected in the galactic fountain model. Diffuse X-ray emission surrounds the disk with a Half Width at Half Maximum (HWHM) for the surface brightness perpendicular to the disk of 50 sec (2.4 kpc) and a radial extent of approximately 6.5 kpc, both of which are similar in extent to the extended H(alpha) and radio halo component; the implied density scale height for the hot gas is 7 kpc. The spectrum is best fitted with a hard stellar component and a soft diffuse gas component of temperature 3.6 x 10(exp 6) K. The density of this gas is 2 x 10(exp -3)/cu cm, the luminosity is 4.4 x 10(exp 39) ergs/s, the mass is 1 x 10(exp 8) solar mass, and the pressure (P/k) is 1.4 10(exp 4) K/cu cm. These data are consistent with this gas participating in a galactic fountain, where the material approaches hydrostatic equilibrium before cooling at a rate of 0.12 solar mass/yr. The cooled material may be responsible for some of the H(alpha) emission.