Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STEELS, STAINLESS - WELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

The Effects of Acid Passivation, Tricresyl Phosphate Pre-Soak, and UV/Ozone Treatment on the Tribology of Perfluoropolyether-Lubricated 440C Stainless Steel Couples

The boundary-lubrication performance of perfluoropolyether (PFPE) thin films in the presence of passivated 440 C stainless steel is presented. The study utilized a standard ball-on-disc tribometer. Stainless steel surfaces were passivated with one of four techniques: 1) submersion in a chromic acid bath for 30 minutes at 46 C, 2) submersion in a chromic acid bath for 60 minutes at 56 C, 3) submersion in a tricresyl phosphate (TCP) bath for 2 days at 107 C, or 4) UV/Ozone treated for 15 minutes. After passivation, each disc had a 400 A film of PFPE (hexafluoropropene oxide) applied to it reproducibly (+/- 20%) and uniformly (+/- 15%) using a film deposition device. The lifetimes of these films were quantified by measuring the number of sliding wear cycles required to induce an increase in the friction coefficient from an initial value characteristic of the lubricated wear couple to a final, or failure value, characteristic of an unlubricated, unpassivated wear couple. The lubricated lifetime of the 440 C couple was not altered as a result of the various passivation techniques. The resulting surface chemistry of each passivation technique was examined using X-ray Photoelectron Spectroscopy (XPS). It was found that chromic acid passivation altered the Cr to Fe ratio of the surface. TCP passivation resulted in a FePO4 layer on the surface, while UV/Ozone passivation only removed the carbonaceous contamination layer. None of the passivation techniques were found to dramatically increase the oxide film thickness.

Shogrin, Bradley A.↗

Measurement of the Hugoniot and shock-induced phase transition stress in wrought 17-4 PH H1025 stainless steel

Uniaxial strain, reverse-ballistic impact experiments were performed on wrought 17-4 PH H1025 stainless steel, and the resulting Hugoniot was determined to a peak stress of 25 GPa through impedance matching to known standard materials. The measured Hugoniot showed evidence of a solid–solid phase transition, consistent with other martensitic Fe-alloys. The phase transition stress in the wrought 17-4 PH H1025 stainless steel was measured in a uniaxial strain, forward-ballistic impact experiment to be 11.4 GPa. Linear fits to the Hugoniot for both the low and high pressure phase are presented with corresponding uncertainty. The low pressure martensitic phase exhibits a shock velocity that is weakly dependent on the particle velocity, consistent with other martensitic Fe-alloys.

36 MATERIALS SCIENCE↗

Ferritic stainless steel interconnects for protonic ceramic electrochemical cell stacks: Oxidation behavior and protective coatings

Protonic ceramic fuel or electrolysis cells (PCFC/PCEC) have shown promising performance at intermediate temperatures. However, these technologies have not yet been demonstrated in a stack, hence the oxidation behavior of the metallic interconnect under relevant operating environments is unknown. In this work, ferritic stainless steels 430 SS, 441 SS, and Crofer 22 APU were investigated for their use as interconnect materials in the PCFC/PCEC stack. Specifically, the bare metal sheets were exposed to a humidified air environment in the temperature range from 450 °C to 650 °C, to simulate their application in a PCFC cathode or PCEC anode. Breakaway oxidation with rapid weight gain and Fe outward diffusion/oxidation was observed on all the selected stainless steel materials. A protective coating is deemed necessary to prevent the metallic interconnect from oxidizing. To mitigate the observed breakaway oxidation, state-of-the-art protective coatings, Y 2 O 3 , Ce 0.02 Mn 1.49 Co 1.49 O 4 , CuMn 1.8 O 4 and Ce/Co, were applied to the stainless steel sheets and their oxidation resistance was investigated. Dual atmosphere testing further validated the effectiveness of the protective coatings in realistic PCFC/PCEC environments, with a hydrogen gradient across the interconnect. Several combinations of metal and coating material were found to be viable for use as the interconnect for PCFC/PCEC stacks.

25 ENERGY STORAGE↗

Effect of Aluminizing on the High-Temperature Oxidation Behavior of an Alumina-Forming Austenitic Stainless Steel

Due to their excellent oxidation resistance and creep resistance at elevated temperatures, alumina forming austenitic (AFA) stainless steels have emerged as potential alloys for high temperature applications. In this study, a Reactive Air Aluminizing (RAA) method was used to aluminize the surface of AFA25 stainless steel. The high temperature oxidation behavior of both as-received and aluminized AFA25 was investigated at 850 °C in dry air. The mass gain per unit area was higher for the aluminized AFA25 than for the as-received material. X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDXS), performed on the oxide scales following the high temperature oxidation tests, confirmed the formation of alumina scale on both as-received and aluminized AFA. However, the aluminized alloy exhibited a thicker alumina scale on the surface, as well as more extensive penetration of the scale into the subsurface region of the alloy.

Rashidi, S.↗

Stochastic room temperature creep of 316 L stainless steel

The creep behavior of 316 L stainless steel at room temperature was evaluated as a function of time and applied stress using a new high-throughput approach. Several common creep models were evaluated against the observations, leading to deeper analysis of a stress-dependent modified logarithmic creep model. Within this model, multiple sources of uncertainty were compared. Aleatoric stochastic variation between samples under nominally identical conditions was identified as the primary contributor to uncertainty in creep response. Under any particular set of conditions, the sample-to-sample variability in creep strain was as high as a factor of two, highlighting the engineering importance of characterizing large statistical datasets. The model's extrapolation capabilities were assessed by comparing predictions derived from calibration on partial, shorter-duration subsets of the data. In conclusion, these findings underscore the importance of accounting for stochastic effects in predictive modeling of aging phenomena.

High-throughput↗

Mechanical Properties of 17-4PH Stainless Steel Foam Panels

Rectangular 17-4PH stainless steel sandwiched foam panels were fabricated using a commercial manufacturing technique by brazing two sheets to a foam core. Microstructural observations and ultrasonic nondestructive evaluation of the panels revealed large variations in the quality of the brazed areas from one panel to the next as well as within the same panel. Shear tests conducted on specimens machined from the panels exhibited failures either in the brazed region or in the foam core for the poorly brazed and well-brazed samples, respectively. Compression tests were conducted on the foam cores to evaluate their elastic and plastic deformation behavior. These data were compared with published data on polymeric and metallic foams, and with theoretical deformation models proposed for open cell foams.

Raj, S. V.↗

Compositional Homogeneity in Rapidly Solidified 316L stainless steel produced by laser powder-bed fusion processing

The segregation of alloying elements in rapidly solidified 316L stainless steel produced using additive manufacturing technologies is widely reported throughout literature. The microstructure of thin walls manufactured from 316L stainless steel using laser powder bed fusion are examined for the presence of alloy segregation, i.e. the rejection of solutes to grain boundaries. Metallographic methods including mechanical polishing and chemical etching are used to prepare samples for microanalysis m

Jankowski, Alan F. [Sandia National Laboratories (↗

Passivation of Stainless Steel for Tritium Service

The goal of this project was to develop a method to passivate stainless steel components using electropolishing techniques and heat treatment methods. The process is intended to limit the in growth and isotope exchange of hydrogen with tritium and deuterium as well as other undesired contaminants of standard gas mixtures. This process has been named Q-Passivation, to set is apart from standard industrial passivation methods and a patent application has been submitted and publish on the process. The basis used for the development of this process was taken from the surface analytical data collected from decommissioned commercial tritium containment vessels that are used to hold standard gas mixtures. The information gained from the surface analysis along with the methods to eliminate residual hydrogen contamination will provide a reasonable method for passivation. Barriers in fabricating test vessels for tritium have delayed production for tritium exposure trials. Some of these barriers include base metal composition that may meet compositional specifications but does not meet a quality inspection as it contains inclusions, additional phases, and other metallurgical anomalies. A number of issues and challenges were encountered during this project that should be resolved. These challenges include base material specification, a non-destructive quality assurance technique, the use of other materials aside from 304L stainless steel, and reuse of expired standard gas containers.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Investigation of micro-structure and micro-hardness properties of 304L stainless steel treated in a hot cathode arc discharge plasma

We have established a hot cathode arc discharge plasma system, where different stainless steel samples can be treated by monitoring the plasma parameters and nitriding parameters independently. In the present work, a mixture of 70% N{sub 2} and 30% H{sub 2} gases was fed into the plasma chamber and the treatment time and substrate temperature were optimized for treating 304L Stainless Steel samples. Various physical techniques such as x-ray diffraction, energy dispersive x-ray spectroscopy and micro-vickers hardness tester were employed to determine the structural, surface composition and surface hardness of the treated samples.

36 MATERIALS SCIENCE↗

TRITIUM AGING EFFECTS ON THE FRACTURE TOUGHNESS PROPERTIES OF FORGED STAINLESS STEEL

The fracture toughness properties of Type 21-6-9 stainless steel were measured for forgings in the unexposed, hydrogen-exposed, and tritium-exposed-and-aged conditions. Fracture toughness samples were cut from conventionally-forged and high-energy-rate-forged forward-extruded cylinders and mechanically tested at room temperature using ASTM fracture-toughness testing procedures. Some of the samples were exposed to either hydrogen or tritium gas (340 MPa, 623 K) prior to testing. Tritium-exposed samples were aged for up to seven years and tested periodically in order to measure the effect on fracture toughness of {sup 3}He from radioactive tritium decay. The results show that hydrogen-exposed and tritium-exposed samples had lower fracture- toughness values than unexposed samples and that fracture toughness decreased with increasing decay {sup 3}He content. Forged steels were more resistant to the embrittling effects of tritium and decay {sup 3}He than annealed steels, although their fracture-toughness properties depended on the degree of sensitization that occurred during processing. The fracture process was dominated by microvoid nucleation, growth and coalescence; however, the size and spacing of microvoids on the fracture surfaces were affected by hydrogen and tritium with the lowest-toughness samples having the smallest microvoids and finest spacing.

08 HYDROGEN↗

Level 2 Milestone Report – Additively Manufactured 304L Stainless Steel

The purpose of this milestone was to support an active research project at Los Alamos National Laboratory to determine the dynamic properties, specifically the equation of state, of additively manufactured (AM) 304L stainless steel and compare to those of forged metal. Our contribution was to measure the shock Hugoniot of AM 304L stainless steel in both the build (growth) and in-plane (transverse) directions and compare those results to similar measurements in forged 304L. These experiments were conducted on the C3 Launcher located in North Las Vegas.

304L stainless steel↗

Thermodynamics of an austenitic stainless steel (AISI-348) under in situ TEM heavy ion irradiation

The stability of the face-centred cubic austenite (γ-Fe) phase in a commercial stainless steel (AISI348) was investigated through in situ transmission electron microscopy (TEM) with heavy ion irradiation at 1073 K up to a fluence of 1.3×10 17 ions·cm -2 (corresponding to a dose of 46 dpa). The γ-Fe phase was observed to decompose at a fluence of around 7.8×10 15 ions·cm -2 (3 dpa) when a new phase nucleated and grew upon increasing irradiation dose. Scanning transmission electron microscopy (STEM) with energy dispersive X-ray (EDX) spectroscopy and multivariate statistical analysis (MVSA) were used to characterise the irradiated specimens. The combination of such experimental techniques with calculated equilibrium phase diagrams using the CALPHAD method led to the conclusion that the new phase formed upon irradiation is the body-centred cubic Cr-rich α 0 phase. At the nanoscale, precipitation of M 23 C 6 (τ-carbide) was also observed. The results indicate that ion irradiation can assist the austenitic stainless steel to reach a non-equilibrium state similar to a calculated equilibrium state observed at lower temperatures in which, under conventional conditions, is suppressed due to kinetic restrictions.

36 MATERIALS SCIENCE↗

Dynamic Data-Driven Multiscale Modeling for Predicting Microstructure and Mechanical Properties of 316L Stainless Steel

We have developed a long short-term memory stacked ensemble (LSTM-SE) surrogate modeling approach that can provide rapid predictions of microstructural evolution and the resultant mechanical properties of American Iron and Steel Institute (AISI) 316L series stainless steel (316LSS) fuel cladding under conditions of varying temperature and radiation dose rate. To acquire training data, we developed and implemented a kinetic Monte Carlo (KMC) model to simulate precipitation kinetics of M 23 C 6 , γ', and G phases within SS316L cladding. Experimentally reported precipitation kinetics of SS316L in literature were linked to the kinetic parameters of the simulated precipitation in our KMC model. The model was then used to simulate microstructure evolution under synthetically generated treatments of varying temperature and radiation dose rate, for periods of up to 3000 hours. Changes in volume fraction, number density, and particle size of precipitates were recorded, and particle area fractions were correlated using statistical methods to develop the surrogate model. Simultaneously, the mechanical properties of the simulated microstructures were evaluated using microstructure-based finite element method (FEM) analysis to determine the elastic modulus, yield stress, ultimate tensile strength, and elongation to failure of the aged microstructures. Using this approach, our surrogate model can predict precipitation behavior within 0.25% volume fraction and mechanical properties within 6% relative error from the values predicted by the KMC and FEM models using 50 training simulations as input. The trained recurrent neural network-based model can return estimations of precipitation kinetics and mechanical properties ~1000 times faster than the physics-based codes. This work demonstrates, as a proof of concept, that reactor material service lifetimes under variable service conditions can be predicted for a statistics-based model from a practicably obtainable dataset.

36 MATERIALS SCIENCE↗

Demystify radiation-enhanced hydrogen isotope diffusion in Fe-Ni-Cr austenitic stainless steels

Understanding and containing hydrogen isotope diffusion is crucial for many nuclear applications. In situ experiments have consistently shown that radiation significantly enhances isotope diffusion in austenitic stainless steels. Despite extensive research, the mechanism behind this phenomenon remains elusive, as most radiation-induced defects (e.g., vacancies, dislocations, and grain boundaries) typically trap hydrogen, thereby slowing diffusion. While grain boundaries may increase in-plane diffusivity and interstitials may enhance diffusion due to material swelling, these effects are relatively minor. Utilizing an Fe-Ni-Cr-H interatomic potential for stainless steels, we conducted extensive molecular dynamics simulations to investigate the origins of radiation-enhanced diffusion. Here, our findings reveal that when a system is resolidified, mimicking defects created by radiation displacements, the resulting structure contains a mixture of phases, boundaries, and dislocation networks. This defective structure significantly increases hydrogen diffusivity, enhancing it by approximately 1.7 times at 900 K. These results suggest that the complex defect structures formed during radiation displacements are the primary drivers of the observed diffusion enhancement, providing valuable insights into the mechanisms underlying radiation-enhanced diffusion in nuclear materials.

36 MATERIALS SCIENCE↗

Characterization of a Cast Duplex Stainless Steel with 3.0%Cu and Modeling of Precipitation Hardening

Duplex stainless steels (DSSs) are corrosion-resistant alloys extensively used in aggressive environments. Cast DSSs may be selected for pipes, valves and pumps in chemical, petrochemical and nuclear industries. The grade steel ASTM A890 1B is an example of cast DSS with 2.7-3.3%Cu addition. Copper increases the resistance to many types of corrosion, especially in non-oxidizing environments. When the copper content is higher than 2%, the steel can be precipitation-hardened. In this work, the precipitation hardening of a DSS ASTM A890 1B steel with 3.0%Cu was studied and modeled for aging temperatures in the 450-600 °C range. Copper precipitates in the ferrite phase, but remains in solid solution in the austenite. The age hardening curves were modeled by ΔH = K(t){sup n} model, where ΔH is the increase in hardness, t is the aging time, and K and n are constants to be determined. The microstructure and substructure were investigated by scanning electron and transmission electron microscopes.

36 MATERIALS SCIENCE↗

Porous Interlayers that Getter Surface-Segregating Species for Improved Silver Wetting, Adhesion, and Electrical Contact on Stainless Steel SOFC Components

Here, porous nickel interlayers or porous platinum interlayers were shown to promote the wetting, spreading, and adhesion of silver on alumina-forming ferritic stainless steel (AFFSS) and chromia-forming ferritic stainless steel (CFFSS). These interlayers resulted in dense, crack-free AFFSS|Ag-Ni|CFFSS and AFFSS|Ag-Pt|CFFSS braze joints that, after 300 h in 650 °C air, displayed shear strengths up to 70 MPa similar to, or larger than, those of AFFSS|Ag-CuO|CFFSS or AFFSS|Ag|CFFSS joints subjected to identical treatment. Similarly, after exposure to 25 cycles of (50 switches between) 12 h of 650 °C air and 12 h of 650 °C 4%H 2 –96%N 2 , AFFSS|Ag-Ni|CFFSS and AFFSS|Ag-Pt|CFFSS braze joints displayed shear strengths significantly larger than those of AFFSS|Ag-CuO|CFFSS or AFFSS|Ag|CFFSS joints subjected to identical treatment. In addition, nickel and platinum were found to chemically getter surface-segregating steel constituents, particularly Al from the AFFSS. As a result, Ag-Ni and Ag-Pt electrical contact resistances on AFFSS and CFFSS substrates were several orders of magnitude lower than those of conventional Ag-CuO reactive air brazes or Heraeus C8710 Ag contact pastes. Together, these results suggest that Ag-Pt and especially Ag-Ni may be useful for the fabrication of durable joints, seals, and/or electrical contacts in electrical/electrochemical devices exposed to high temperatures and/or variable oxygen partial pressure environments.

36 MATERIALS SCIENCE↗