Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SIDE EFFECTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Operation Plumbbob

On June 24, 1957, a thirty-seven kiloton nuclear device, codenamed Priscilla, exploded 700 feet over the Nevada Test Site’s Frenchman dry lake. Below, on the lakebed, was a bank vault designed by the Mosler Safe Company for one of several Federal Civil Defense Administration experiments. The vault was constructed “to evaluate the effectiveness of a reinforced-concrete vault and steel vault door in providing protection against the effects of a nuclear detonation.” Blast damage to the exterior was largely confined to the side walls, whose concrete was stripped off; its steel reinforcing rods bent and twisted. The vault door was essentially undamaged and was opened with minimal difficulty. The vault contents - sandbags, movie camera, and thermometers - were only slightly disturbed. The camera operated as planned, running 40 ft of film. The film, however, was completely fogged. Two clinical type thermometers registered 88°F, and a 24-hr stylus American temperature recorder registered a constant 88°F. Priscilla was the fifth of twenty-nine tests conducted in 1957 as part of Operation Plumbbob, whose stated purpose was to conduct tests “aimed to attain new knowledge important to the defense of the United States and the Free World.” Individual events included “proof tests of air defense and antisubmarine warheads to be stockpiled, development tests of bomb components and mockups, and design tests of smaller and lighter warheads.” One test, John, was that of an air-to-air missile detonated 18,500 feet over the test site.

99 GENERAL AND MISCELLANEOUS↗

DSO+T: Expanded Study Results DSO+T Study: Volume 5

The Distribution System Operator with Transactive (DSO+T) study investigates the engineering and economic performance of a transactive energy retail market coordinating a high penetration of customer-side flexible energy assets. The study seeks to answer whether such an implementation is cost effective for customers, recovers sufficient revenue for DSOs, and is equally applicable and beneficial to a range of flexible asset types, renewable generation scenarios, and market assumptions. This report volume provides a detailed set of results for the DSO+T study extending results presented in Volumes 1, 2, and 4. The engineering and economic performance of the transactive energy scheme is presented for two separate flexible asset deployments: flexible loads (HVAC units and residential water heaters) and behind-the-meter batteries. The results of each transactive case are compared to a business-as-usual case. These cases are subject to two different renewable generation scenarios, a moderate renewable generation scenario, representative of current levels of renewable generation deployment, and a future high renewables scenario, including the increased deployment of rooftop solar photovoltaic and electric vehicles. The transactive coordination scheme is shown to produce effective and stable control and decrease peak loads 9–15%. The resulting annual demand flexibility provides net economic savings of $3.3–5.0B per year for a region the size of Texas. Detailed analysis shows that net benefits were seen for a range of distribution system operator, customer, and flexible asset types. Both participating customer (with transactive flexible assets) and nonparticipating customers (with nonflexible assets) see reductions in annual utility bills and net annual energy expenses in the range of 10–16%.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Multilayer Electrodes with Metalized Polymer Current Collector for High-Energy Lithium-Ion Batteries with Extreme-Fast-Charging Capability

The pursuit of batteries capable of extreme fast charging (XFC), that also satisfy high energy and safety criteria, poses a significant challenge to current lithium-ion battery technologies. Additionally, the increasing demand for aluminum (Al) and copper (Cu) in electrification, and vehicle light weighting is driving these metals towards near-critical status in the medium term. This study introduced metalized polymer films by depositing an Al or Cu thin layer onto two sides of a polyethylene terephthalate (PET) film – named mPET/Al and mPET/Cu, as lightweight, cost-effective alternatives to traditional metal current collectors in LIBs. We have utilized current collectors that significantly reduce weight (by 73%), thickness (by 33%), and cost (by 85%) compared to traditional metal foil counterparts. We conducted an extensive evaluation of their mechanical and electrical properties, including in-plane and through-plane resistivities, affirming their suitability for the roll-to-roll battery manufacturing process. Additionally, a novel XFC testing protocol was employed to thoroughly assess the cells' (both half and full-cell) performance across various C-rates and under long-term tests. These advancements have the potential to enhance energy density to 280 Wh/kg at the electrode level under 10-minute charging at 6C. Through testing, including a novel XFC protocol across various C-rates and long-term cycling (up to 1000 cycles) in different cell configurations, we have demonstrated the superior performance of these metalized polymer films. Notably, mPET/Cu and mPET/Al foils exhibited comparable capacities to conventional cells under XFC, with the mPET cells showing a 27% improvement in energy density at 6C and maintaining significant energy density after 1000 cycles. This study underscored the potential of mPET foils to revolutionize the roll-to-roll battery manufacturing process and significantly advance the performance metrics of LIBs in EV applications. Moreover, our results suggest that there is potential to enhance the performance of mPET foils, especially mPET/Al, by optimizing the manufacturing process to achieve higher conductivity.

99 GENERAL AND MISCELLANEOUS↗

Multilayer Electrodes with Metalized Polymer Current Collector for High-Energy Lithium-Ion Batteries with Extreme-Fast-Charging Capability

The pursuit of batteries capable of extreme fast charging (XFC), that also satisfy high energy and safety criteria, poses a significant challenge to current lithium-ion battery technologies. Additionally, the increasing demand for aluminum (Al) and copper (Cu) in electrification, and vehicle lightweighting is driving these metals towards near-critical status in the medium term. This study introduced metalized polymer films by depositing an Al or Cu thin layer onto two sides of a polyethylene terephthalate (PET) film – named mPET/Al and mPET/Cu, as lightweight, cost-effective alternatives to traditional metal current collectors in LIBs.

25 ENERGY STORAGE↗

Loss Analysis and Performance Optimization Pathways of 729-mV VocSi Solar Cells with Poly-Si on Locally-Etched Dielectric Passivating Contacts

In this article, the performance analysis of a 22.5% efficient polysilicon on silicon oxide (poly-Si/SiOx) passivated contact solar cells with deliberately introduced pinholes using metal-assisted chemical etching (MACE) has been performed with the help of optical analysis using Sunsolve and electrical analysis using Quokka3. The power loss is maximum due to recombination and resistive losses in the bulk (~0.76 mW/cm2 ) followed by power loss due to rear contact recombination (~0.35 mW/cm2 ). Recombination at the front surface also contributes to 0.24 mW/cm2. The effect of improving the bulk lifetime and lowering the recombination current density at the rear side on Voc, FF and efficiency has been investigated.

MACE↗

Effect of the Selective Halogenation of Small Molecule Acceptors on the Blend Morphology and Voltage Loss of High-Performance Solar Cells

Herein, the impacts of the selective halogenation at two different positions of dicyanomethylene-3-indanone (IC) end groups and inner side chains of small molecular acceptors (SMAs) on the P D :SMA interfacial interactions, blend morphology, and resulting photovoltaic properties are described. In this study, four different SMAs (A1, A2, A3, and A4) with the same molecular backbone, but with different degrees of halogenation, are synthesized. The IC end groups on the backbones of the A1 and A3, and A2 and A4 SMAs are chlorinated and fluorinated, respectively; in addition, 6-phenoxyhexyl inner side chains of the A3 and A4 are chlorinated. The SMAs are paired with a chlorinated PBDT-Cl PD to construct organic solar cells (OSCs). The PBDT-Cl:A4-based OSC exhibits the highest power conversion efficiency of 17.2%, outperforming the PBDT-Cl:A1-(13.3%), PBDT-Cl:A2-(15.6%), and PBDT-Cl:A3-based OSC (16.5%). The Cl atoms on the side chains in the A3 and A4 SMAs enhance the molecular/energetic interactions at the P D :SMA interfaces and improve the blend morphology in terms of domain purity and spacing. These effects lead to the improved fill factors and reduced voltage loss of the PBDT-Cl:A3- and PBDT-Cl:A4-based OSCs. This study demonstrates the importance of appropriate halogenation of SMAs in optimizing the blend morphology, reducing voltage loss, and improving OSC performance.

36 MATERIALS SCIENCE↗

Depth profiling and standardization from the back side of a sample for accurate analyses: Emphasis on quantifying low‐fluence, shallow implants in diamond‐like carbon

Rationale Back‐side thinning of wafers is used to eliminate issues with transient sputtering when analyzing near‐surface element distributions. Precise and accurate calibrated implants are created by including a standard reference material during the implantation. Combining these methods allows accurate analysis of low‐fluence, shallow features even if matrix effects are a concern. Methods Implanted Na (<2.0 × 10 11 ions/cm 2 , peaking <50 nm) in diamond‐like carbon (DLC) film on silicon (solar wind returned by NASA's Genesis mission) was prepared for measurement as follows. Implanted surfaces of samples were epoxied to wafers and back‐side‐thinned using physical or chemical methods. Thinned samples were then implanted with reference ions for accurate quantification of the solar wind implant. Analyses used a CAMECA IMS 7f‐GEO SIMS in depth‐profiling mode. Results Back‐side‐implanted reference ions reduced the need to change sample mounts or stage position and could be spatially separated from the solar wind implant even when measuring monoisotopic ions. Matrix effects in DLC were mitigated and the need to find an identical piece of DLC for a reference implant was eliminated. Accuracy was only limited by the back‐side technique itself. Conclusions Combining back‐side depth profiling with back‐side‐implanted internal standards aides quantification of shallow mono‐ and polyisotopic implants. This technique helps mitigate matrix effects and keeps measurement conditions consistent. Depth profile acquisition times are longer, but if sample matrices are homogeneous, procedural changes can decrease measurement times.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-Fidelity Simulation Study of the Unsteady Flow Effects on High-Pressure Turbine Blade Performance

Abstract Unsteadiness, in the form of both broadband background disturbances and discrete coherent wakes, can have a strong effect on the performance of turbomachinery blades. The influence of the incoming flow has received much interest as it inevitably affects the blade boundary layers and develops as it passes through the machine. In the present work, we investigate the effect of unsteady flow on high-pressure turbines (HPTs), using high-fidelity datasets produced by wall resolved large-eddy simulation of an HPT stage. The effects of incident wakes from an upstream stator, compounded by the presence of freestream turbulence, on the downstream rotor are investigated. Based on analyzing cases with different turbulence intensities and length scales prescribed at the inlet, we show that changing the freestream turbulence characteristics has a direct effect on the unsteady behavior of the stator wakes. As a result, the performance of the rotor is also significantly affected. By detailing the influence of the wake–turbulence interaction, we aim to distinguish driving forces on rotor performance, be it changes in the incident wakes or direct influence from the freestream turbulence. Furthermore, the aerothermal behaviors of the rotor blades have been extensively investigated, showing that the blade boundary layers on the suction and pressure sides respond differently to external disturbances. The insights gained can provide designers with guidelines in understanding the unsteady flow effects of a given flow state, and how the unsteadiness present, either broadband or deterministic, will affect the performance of downstream blades.

Engineering↗

Controlling swelling in mixed transport polymers through alkyl side-chain physical cross-linking

Semiconducting conjugated polymers bearing glycol side chains can simultaneously transport both electronic and ionic charges with high charge mobilities, making them ideal electrode materials for a range of bioelectronic devices. However, heavily glycolated conjugated polymer films have been observed to swell irreversibly when subjected to an electrochemical bias in an aqueous electrolyte. The excessive swelling can lead to the degradation of their microstructure, and subsequently reduced device performance. An effective strategy to control polymer film swelling is to copolymerize glycolated repeat units with a fraction of monomers bearing alkyl side chains, although the microscopic mechanism that constrains swelling is unknown. Here we investigate, experimentally and computationally, a series of archetypal mixed transporting copolymers with varying ratios of glycolated and alkylated repeat units. Experimentally we observe that exchanging 10% of the glycol side chains for alkyl leads to significantly reduced film swelling and an increase in electrochemical stability. Through molecular dynamics simulation of the amorphous phase of the materials, we observe the formation of polymer networks mediated by alkyl side-chain interactions. When in the presence of water, the network becomes increasingly connected, counteracting the volumetric expansion of the polymer film.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effectiveness of Vapor Corrosion Inhibitors Under Elevated Chloride Conditions for Aboveground Storage Tank Application

The sand quality used to construct the tank pad is an important contributing factor to the rate of corrosion that occurs on the soil-side of the aboveground storage tanks (ASTs) floor plates. Clean sand that meets specific criteria provides the first line of defense for mitigation of tank floor corrosion. However, it has been observed that the sand quality used for some existing tanks differ greatly from the specifications provided in the API 651 standard; this could be partially due to initial sand quality not meeting the specification, and partially due to the environmental effects over time. For example, rain-water intrusion could lead to higher than the specified contents of corrosive species such as chloride. Tank operators are increasingly using vapor corrosion inhibitors (VCIs) either as a stand alone or in combination with cathodic protection (CP) for ASTs to mitigate soil-side corrosion. VCIs are delivered either through-thefloor or injected through the ports in the ring wall. Experimental studies were conducted to evaluate VCIs’ performance at elevated chloride concentrations and to study the effectiveness of the delivery methods under extreme chloride conditions. The experimental work found that VCI performance is robust and not compromised due to high chloride levels, such as 300 ppm or more. The work also showed that the through-the-floor VCI delivery method is more beneficial compared to the through-the-sand-pad method when tank pad corrosivity is elevated.

Shukla, Pavan K.↗

Visualizing plant cell wall changes proves the superiority of hydrochloric acid over sulfuric acid catalyzed γ-valerolactone pretreatment

Thermochemical pretreatment is one of the key steps to process lignocellulosic biomass for production of biofuels and biomaterials. γ-valerolactone (GVL) has been used as a green and renewable solvent to efficiently dissolve lignin under acidic conditions and enhance subsequent enzyme digestibility. Further improvement is still required to lower the pretreatment temperature in order to reduce sugar degradation and irreversible lignin condensation, as well as the capital cost. In this study, we compared the use of HCl and H 2 SO 4 as catalysts during GVL pretreatment, and found the performance of GVL-HCl at 100 °C was comparable to that of GVL-H 2 SO 4 at 120 °C in terms of xylan and lignin removal and enzyme digestibility. We further monitored the lignin removal and cellulose accessibility in the cell walls at different pretreatment time points by imaging the changes in lignin auto-fluorescence and in CtCBM3-GFP binding with confocal laser scanning microscopy (CLSM), respectively. We found GVL-HCl pretreatment at a relative low temperature (100 °C) could rapidly remove lignin in the compound middle lamella and cell corner areas, which concurred with the increase of CtCBM3-GFP binding in these areas. Real-time imaging of cell wall degradation by cellulases further revealed that the secondary cell walls could be digested from both cell lumen and CML sides, and eventually fully deconstructed within 24 h. Furthermore, our results provide new insight into the effects of chloride anions on plant cell wall structure during GVL pretreatment, and offer potential routes to further optimize and enhance the efficiency of GVL-based pretreatment.

09 BIOMASS FUELS↗

Deformation and Fracture Behaviors of Cylindrical Battery Shell During Thermal Runaway

Thermal runaway is one of the catastrophic failure modes of lithium-ion cells. During thermal runaway in cylindrical cells, sidewall shell rupture has been identified as a contributing factor for thermal runaway propagation in battery packs. Herein, the deformation and fracture behaviors of the battery shell during thermal runaway are investigated based on in-situ and ex-situ characterization as well as physics-based modeling. The deformation and fracture modes of the battery shell with/without Carbon Fiber Reinforced Polymer (CFRP) sleeves are identified. In the simulation, the strain introduced by thermal expansion of the system is considered, as well as the thermal and strain rate effects on the plastic stage. The final cell shell modeling is validated by cell thermal runaway tests. Results reveal the quantitative relation between shell deformation behaviors and the pressure and temperature distribution. Both the experiment and model demonstrate the effectiveness of adding a tight-fitting CFRP sleeve around the cell in limiting the side-wall rupture of the shell. The use of CFRP tubes introduces a novel phenomenon in the context of uneven temperature distribution. Results shed light on the mechanistic analysis of a cell side-wall rupture during thermal runaway and provide essential guidance for the next-generation safe battery design.

battery casing↗

Probing single-chain conformation and its impact on the optoelectronic properties of donor–accepter conjugated polymers

The chain conformation of donor–acceptor conjugated polymers (D–A CPs) is critical to their optical and electronic properties. However, probing the conformation of D–A CPs (e.g., persistence length and contour length) at a single-chain level is challenging due to the formation of aggregates in dilute solution, even in a good solvent. In this work, we studied the chain conformation and corresponding optical spectra for high-performance D–A CPs in the single-chain state by multimodal variable-temperature scattering and spectroscopy techniques, as well as by molecular dynamics simulations. Here we found a critical role of the side-chain length and branch point in the persistence length and optical absorption due to steric effects. Hence, it is important to consider both the chain rigidity and coplanarity of the polymer backbone to achieve desirable optoelectronic properties. Our findings bridge the fundamental knowledge gaps to design new CPs with desired optoelectronic properties via molecular engineering for next-generation electronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reduction in RF sheath rectification with insulating antenna enclosure walls

Abstract Radiofrequency (RF) sheath rectification is one of the most prominent deleterious effects associated with ion cyclotron range of frequencies (ICRF) heating in fusion plasmas. RF sheaths and associated effects, such as impurity generation and convective cell generation, need to be mitigated to ensure that ICRF is a viable option for heating in future fusion devices. Experiments were performed on the Large Plasma Device (LAPD) at UCLA to explore the effects of using electrically-insulating antenna enclosures on RF rectified sheaths. Three different enclosure side-wall materials were used, including copper, MACOR (electrically insulating), and MACOR over copper. In the case of the MACOR–copper side walls, the non-conductive MACOR material was exposed to the bulk plasma but a layer of copper was added below to allow for image currents to flow. All three of the experiments had similar plasma density, temperature, and background magnetic field. In the case of the copper enclosure, RF rectified potentials, many times the local electron temperature, and associated formation of convective cells were observed and reported Martin M. et al (2017 Phys. Rev. Lett. 119 205002). In the experiments with MACOR and MACOR–copper enclosures, RF rectification was significantly reduced. Additionally, these latter two experiments showed no evidence of convective cell formation. Although the results from the MACOR experiment are reminiscent of the results obtained in ASDEX-U with a three-strap antenna optimized to reduce image currents on the antenna limiters Bobkov V. et al (2016 Nucl. Fusion 56 084001), the MACOR–copper experiment seems to suggest that insulating plasma facing materials have at least an equally strong impact on reducing potential rectification.

Physics↗

Block Lanczos algorithm for lattice QCD spectroscopy and matrix elements

Recent work introduced a new framework for analyzing correlation functions with improved convergence and signal-to-noise properties, as well as rigorous quantification of excited-state effects, based on the Lanczos algorithm and spurious eigenvalue filtering with the Cullum-Willoughby test. Here, we extend this framework to the analysis of correlation-function matrices built from multiple interpolating operators in lattice quantum chromodynamics (QCD) by constructing an oblique generalization of the block Lanczos algorithm, as well as a new physically motivated reformulation of the Cullum-Willoughby test that generalizes to block Lanczos straightforwardly. The resulting block Lanczos method directly extends generalized eigenvalue problem (GEVP) methods, which can be viewed as applying a single iteration of block Lanczos. Block Lanczos provides qualitative and quantitative advantages over GEVP methods analogous to the benefits of Lanczos over the standard effective mass, including faster convergence to ground- and excited-state energies, explicitly computable two-sided error bounds, straightforward extraction of matrix elements of external currents, and asymptotically constant signal-to-noise. No fits or statistical inference are required. Proof-of-principle calculations are performed for noiseless mock-data examples as well as two-by-two proton correlation-function matrices in lattice QCD.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Superconducting dome in ferroelectric-type materials from soft mode instability

Here we present a minimal theory of superconductivity enhancement in ferroelectric-type materials. Simple expressions for the optical mode responsible for the soft mode transition are assumed. A key role is played by the anharmonic phonon damping which is modulated by an external control parameter (electron doping or mechanical strain) causing the appearance of the soft mode. It is shown that the enhancement in the superconducting critical temperature T c upon approaching the ferroelectric transition from either side is due to the Stokes electron-phonon scattering processes promoted by strong phonon damping effects.

36 MATERIALS SCIENCE↗

X-Ray Characterization of Real Fuel Sprays for Gasoline Direct Injection

Here, the effects of fuel blend properties on spray and injector performance has been investigated in a side-mount injector for gasoline direct injection (GDI) using two certification fuel blends: Euro 5 and Euro 6. Several X-ray diagnostic techniques were conducted to characterize the injector and spray morphology. Detailed internal geometry of the GDI injector was resolved to 1.8 μm, through the use of hard X-ray tomography. The geometry characterization of this six-hole GDI, side mount injector, quantifies relevant hole and counterbore dimensions and reveals the intricate details within the flow passages, including surface roughness and micron-sized features. Internal valve motion was measured with a temporal resolution of 20 μs and a spatial resolution of 2.0 μs, for three injection pressures and several injector energizing strategies. The needle motion for both fuels exhibits similar lift profiles for common energizing commands. A combination of X-ray radiography and ultra-small-angle X-ray scattering (USAXS) was used to characterize the fuel mass distribution and the droplet sizing, respectively. Tomographic spray radiography revealed the near-nozzle distribution of fuel mass for each of the fuels and the asymmetry produced by the angled nozzles. Under evaporative conditions, the two fuels show minor differences in peak fuel mass distribution during steady injection, though both exhibit fluctuations in injection during the early, transient phase. USAXS measurements of the path-specific surface area of the spray indicated lower peak values for the more evaporative conditions in the near nozzle region.

09 BIOMASS FUELS↗

First-Principles Studies of Tritium Species Diffusivity Across the Interface of Nickel-Plated Zircaloy-4

In this study, we will calculate the 3H2 and 3H2O diffusion mechanism in the Ni coated layer and the dominant 3H species dissolution into the Zircaloy-4 getter. We will optimize the Ni/Zr interface and introduce Sn and O impurities. To achieve the objectives, we will perform the investigation by using spin-polarized density functional theory (DFT) methods to capture the effects of Ni magnetic properties on 3H diffusion. We will introduce NiO/Ni(OH) on the Ni side closer to the interface. Then, the 3H diffusion pathways and barriers from Ni side to the zircalory-4 will be explored. We will investigate how NiO/Ni(OH) affects the 3H diffusion across the interface.

Paudel, Hari P.↗