Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Recrystallization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

The evolution with strain of the stored energy in different texture components of cold-rolled IF steel revealed by high resolution X-ray diffraction

During the deformation of low carbon steel by cold-rolling, dislocations are created and stored in grains depending on local crystallographic orientation, deformation, and deformation gradient. Orientation dependent dislocation densities have been estimated from the broadening of X-ray diffraction lines measured on a synchrotron beamline. Different cold-rolling levels (from 30% to 95% thickness reduction) have been considered. It is shown that the present measurements are consistent with the hypothesis of the sole consideration of screw dislocations for the analysis of the data. The presented evolutions show that the dislocation density first increases within the α fiber (=(hkl)<110>) and then within the γ fiber (=(111) ). A comparison with EBSD measurements is done and confirms that the storage of dislocations during the deformation process is orientation dependent and that this dependence is correlated to the cold-rolling level. If we assume that this dislocation density acts as a driving force during recrystallization, these observations can explain the fact that the recrystallization mechanisms are generally different after moderate or large strains. - Highlights: • Dislocation densities are assessed by XRD in main texture components of a steel sheet. • Dislocation densities vary with both strain and texture components. • The analysis relies on the sole presence of screw dislocations. • The measured dislocation densities include the contribution of both SSD and GND.

36 MATERIALS SCIENCE↗

Effect of intermediate annealing on the microstructure and mechanical property of ZK60 magnesium alloy produced by twin roll casting and hot rolling

Twin roll cast (designated as TRC in short) ZK60 magnesium alloy strip with 3.5 mm thickness was used in this paper. The TRC ZK60 strip was multi-pass rolled at different temperatures, intermediate annealing heat treatment was performed when the thickness of the strip changed from 3.5 mm to 1 mm, and then continued to be rolled until the thickness reached to 0.5 mm. The effect of intermediate annealing during rolling process on microstructure, texture and room temperature mechanical properties of TRC ZK60 strip was studied by using OM, TEM, XRD and electronic universal testing machine. The introduction of intermediate annealing can contribute to recrystallization in the ZK60 sheet which was greatly deformed, and help to reduce the stress concentration generated in the rolling process. Microstructure uniformity and mechanical properties of the ZK60 alloy sheet were also improved; in particular, the room temperature elongation was greatly improved. When the TRC ZK60 strip was rolled at 300 °C and 350 °C, the room temperature elongation of the rolled sheet with 0.5 mm thickness which was intermediate annealed during the rolling process was increased by 95% and 72% than that of no intermediate annealing, respectively. - Highlights: • Intermediate annealing was introduced during hot rolling process of twin roll cast ZK60 alloy. • Intermediate annealing can contribute to recrystallization and reduce the stress concentration in the deformed ZK60 sheet. • Microstructure uniformity and mechanical properties of the ZK60 sheet were improved, in particular, the room temperature elongation. • The elongation of the rolled ZK60 sheet after intermediate annealed was increased by 95% and 72% than that of no intermediate annealing.

36 MATERIALS SCIENCE↗

Hot deformation characterization of duplex low-density steel through 3D processing map development

The high temperature deformation behavior of duplex low-density Fe–18Mn–8Al–0.8C steel was investigated at temperatures in the range of 600–1000 °C. The primary constitutive analysis indicated that the Zener–Hollomon parameter, which represents the coupled effects of temperature and strain rate, significantly varies with the amount of deformation. Accordingly, the 3D processing maps were developed considering the effect of strain and were used to determine the safe and unsafe deformation conditions in association with the microstructural evolution. The deformation at efficiency domain I (900–1100 °C\10{sup −} {sup 2}–10{sup −} {sup 3} s{sup −} {sup 1}) was found to be safe at different strains due to the occurrence of dynamic recrystallization in austenite. The safe efficiency domain II (700–900 °C\1–10{sup −} {sup 1} s{sup −} {sup 1}), which appeared at logarithmic strain of 0.4, was characterized by deformation induced ferrite formation. Scanning electron microscopy revealed that the microband formation and crack initiation at ferrite\austenite interphases were the main causes of deformation instability at 600–800 °C\10{sup −} {sup 2}–10{sup −} {sup 3} s{sup −} {sup 1}. The degree of instability was found to decrease by increasing the strain due to the uniformity of microbanded structure obtained at higher strains. The shear band formation at 900–1100 °C\1–10{sup −} {sup 1} s{sup −} {sup 1} was verified by electron backscattered diffraction. The local dynamic recrystallization of austenite and the deformation induced ferrite formation were observed within shear-banded regions as the results of flow localization. - Graphical abstract: Display Omitted - Highlights: • The 3D processing map is developed for duplex low-density Fe–Mn–Al–C steel. • The efficiency domains shrink, expand or appear with increasing strain. • The occurrence of DRX and DIFF increases the power efficiency. • Crack initiation at α/γ interphase and shear banding lead to failure.

36 MATERIALS SCIENCE↗

Gas tungsten arc welding and friction stir welding of ultrafine grained AISI 304L stainless steel: Microstructural and mechanical behavior characterization

In the present study, an ultrafine grained (UFG) AISI 304L stainless steel with the average grain size of 650 nm was successfully welded by both gas tungsten arc welding (GTAW) and friction stir welding (FSW). GTAW was applied without any filler metal. FSW was also performed at a constant rotational speed of 630 rpm and different welding speeds from 20 to 80 mm/min. Microstructural characterization was carried out by High Resolution Scanning Electron Microscopy (HRSEM) with Electron Backscattered Diffraction (EBSD) and Transmission Electron Microscopy (TEM). Nanoindentation, microhardness measurements and tensile tests were also performed to study the mechanical properties of the base metal and weldments. The results showed that the solidification mode in the GTAW welded sample is FA (ferrite–austenite) type with the microstructure consisting of an austenite matrix embedded with lath type and skeletal type ferrite. The nugget zone microstructure in the FSW welded samples consisted of equiaxed dynamically recrystallized austenite grains with some amount of elongated delta ferrite. Sigma phase precipitates were formed in the region ahead the rotating tool during the heating cycle of FSW, which were finally fragmented into nanometric particles and distributed in the weld nugget. Also there is a high possibility that the existing delta ferrite in the microstructure rapidly transforms into sigma phase particles during the short thermal cycle of FSW. These suggest that high strain and deformation during FSW can promote sigma phase formation. The final austenite grain size in the nugget zone was found to decrease with increasing Zener–Hollomon parameter, which was obtained quantitatively by measuring the peak temperature, calculating the strain rate during FSW and exact examination of hot deformation activation energy by considering the actual grain size before the occurrence of dynamic recrystallization. Mechanical properties observations showed that the welding efficiency of the FSW welded sample is around 70%, which is more than 20% higher than the GTAW welded sample. - Highlights: • Microstructure and mechanical properties of UFG 304L stainless steel were studied during GTAW and FSW. • Sigma phase formation mechanism was studied during FSW of 304L stainless steel. • THERMOCALC analysis was performed to obtain possible formation temperatures for sigma phase. • Nano-mechanical twins were found in the TMAZ region.

36 MATERIALS SCIENCE↗

Microstructure, texture, and mechanical properties of friction stir welded commercial brass alloy

Microstructural evolution during friction stir welding of single-phase brass and corresponding mechanical properties were investigated. For this purpose, 2 mm thick brass plate was friction stir welded at a rotational speed of 450 rpm and traverse speed of 100 mm/min. The microstructure of the joint was studied using optical microscopy, scanning electron microscopy equipped with electron back scattered diffraction system, and scanning transmission electron microscopy. The mechanical properties were measured using hardness and tensile tests. The formation of subgrains and their transformation into new grains in conjunction with existence of A{sub 1}{sup ⁎}, A{sub 2}{sup ⁎} and C texture components revealed that the continuous dynamic recrystallization plays a dominant role in the microstructural evolution. However, grain boundary bulging, along with the formation of twin boundaries, and presence of the G texture component showed that the discontinues dynamic recrystallization may participate in the new grain formation. Furthermore, the different strengthening mechanisms, which caused the higher strength of the joint, were discussed. - Highlights: •Microstructural evolution during FSW of a single phase brass was investigated. •CDRX and DDRX were the main mechanisms of the grain structure formation during FSW. •GDRX and SRX were not contributed in grain structure formation. •The lamellas TBs were formed in the SZ of the joints. •Grain boundary, dislocation, and texture effects resulted in higher strength.

36 MATERIALS SCIENCE↗

Mitigation of tin whisker growth by inserting Ni nanocones

Highlights: • Tin whisker growth is mitigated effectively by inserting Ni nanocones. • Ni nanocones impede Sn dynamic recrystallization by blocking dislocation motions. • The inhibition method and mechanism are important to the study of tin whisker. - Abstract: An innovative controllable way has been proposed to mitigate tin whisker growth by inserting Ni nanocones prepared by electrodeposition. The results reveal that, after inserting Ni nanocones, tin whisker formation is mitigated effectively for 1.6 μm Sn coating but there is no inhibition effect for 4.5 μm Sn coating. The coatings are characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectrometer and electron backscatter diffraction (EBSD). The EBSD results show that Sn grain size without Ni nanocones increases significantly after indentation test compared with Sn grains with Ni nanocones. The inhibition effect of Ni nanocones on whisker growth can be ascribed to its specific structure which prevents dynamic recrystallization and produces horizontal grain boundaries of Sn grains. The structural inhibition method and mechanism proposed are of great importance to the research of tin whisker.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Study on hot deformation behavior and workability of squeeze-cast 20 vol%SiCw/6061Al composites using processing map

Highlights: • Prasad’s and Murty’s criteria were better than Gegel’s criterion in predicting the flow instability for the composites. • Partial melting and DRX at high temperature and high strain rate improved the workability of the composites. • The softening mechanism changed from DRV to DRX with the increase of deformation temperature and strain rate. • The safe deformation region of the composites was at higher temperature of 450-500°C and higher strain rate of 0.1-1s{sup -1}. • The safe deformation region predicted by processing maps was validated by uniaxial upsetting and two-directional forging. - Abstract: The hot deformation behavior and workability of squeeze-cast 20 vol%SiCw/6061Al composites were investigated by isothermal compression test and development of processing map, which was verified by uniaxial upsetting and two-directional forging of big cylindrical billets. Due to dispersed strengthening caused by SiC whiskers, the activation energy of 20 vol%SiCw/6061Al composites was much higher than the self-diffusion activation energy of pure Al. Both the DMM and MDMM were reliable in predicting the safe deformation regions. The instability regions predicted by the Prasad's and Murty's instability criterion were smaller than the actual ones, while the Gegel's instability criterion was not appropriate in predicting the instability regions of 20 vol%SiCw/6061Al composites. The optimum deformation region was at higher temperature of 450–500 °C and higher strain rate of 0.1–1 s{sup − 1}, in which the compressed samples exhibited perfect surface without cracks and microstructure with few of cavities due to the occurrence of partial melting and dynamic recrystallization. With the increase of deformation temperature and strain rate, the deformation mechanism changed from dynamic recovery to dynamic recrystallization. Squeezing casting technique with high filtration pressure may also contribute to the increase of strain rate of DRX, which was helpful for hot forging of Al matrix composites with high productivity.

36 MATERIALS SCIENCE↗

Effect of microstructure on exfoliation corrosion resistance in an Al-Zn-Mg alloy

Highlights: • A quantitative method was proposed to characterize EXCO resistance. • The EXCO product lead to strain in ND and elongation in RD on nearby grains. • Recrystallized grains are more susceptible to EXCO than fibrous grains. • High fraction of high-angle grain boundaries reduces EXCO resistance. • High coverage ratio of η phases on high-angle grain boundaries reduces EXCO resistance. - Abstract: In this work, the effect of microstructure on exfoliation corrosion (EXCO) resistance in an Al-Zn-Mg alloy were investigated using standard EXCO test, together with detailed microstructural examinations mainly by scanning electron microscopy (SEM) and high-angle annular detector dark-field scanning transmission electron microscopy (HAADF-STEM). An EXCO product model was built based on morphologies of EXCO product on longitudinal section and cross section for further measurement and analysis. A quantitative characterization of EXCO resistance by measuring average thickness of EXCO product was conducted, showing average results of 6.94 μm, 10.21 μm and 18.14 μm, which are corresponding to EXCO ratings of P, EA and EB under ASTM G34 standard, respectively. It was concluded that recrystallization, high fraction of high-angle grain boundaries (HAGBs) and high coverage ratio of η phases on HAGBs reduced EXCO resistance.

36 MATERIALS SCIENCE↗

Effects of friction stir processing and minor Sc addition on the microstructure, mechanical properties, and damping capacity of 7055 Al alloy

Highlights: • Good mechanical and damping properties were obtained in the 7055 after FSP and Sc addition. • The strengthening and damping mechanisms of FSP 7055(-Sc) were analyzed. • FSP and Sc addition were found to be strategy of preparing 7xxx alloys with well damping and mechanical properties. - Abstract: This study investigated the effects of friction stir processing (FSP) and addition of 0.25% (mass ratio) Sc on the microstructure, mechanical properties, and damping capacity of AA 7055 alloy. Microstructure analyses revealed that a low tool rotation rate of 300 rpm effectively inhibited the grain coarsening in the recrystallization of the alloy during FSP. Sc addition prevented the coarsening of grains and precipitated η phase and the annihilation of dislocations in the FSP AA 7055 alloy. After being subjected to FSP at 300 rpm, the AA 7055 alloy containing Sc exhibited good mechanical and damping properties, which were mainly attributed to the fine recrystallized grain structure, fine precipitated η phase, and large number of nano-sized Al{sub 3}(Sc, Zr) particles located at the grain boundaries and dislocations. This work provides an effective strategy for preparing commercial Al alloys with excellent damping capacity and mechanical properties.

36 MATERIALS SCIENCE↗

Precipitation behavior of ωo phase and texture evolution of a forged Ti-45Al-8.5Nb-(W, B, Y) alloy during creep

Highlights: • The morphology of ω{sub o} and residual β{sub o} phases depends on creep temperature and stress. • Stress can increase the tendency of the α{sub 2} to ω{sub o} phase transformation. • The strength of the texture components depend on temperature and stress. • β{sub o}(ω{sub o}) precipitation retards the growth of recrystallized γ grains. • ω{sub o} precipitation resists and deflects the crack during the crack propagation. - Abstract: Creep rupture tests of the as-forged Ti-45Al-8.5Nb-(W,B,Y) alloy with a duplex microstructure were carried out at 750–850 °C and 130–300 MPa. An investigation was performed to study the effects of temperature and stress on the microstructure and texture evolution, as well as on the creep properties of the forged high Nb-containing TiAl alloy with a duplex microstructure. The results show that the stress exponent n = 2.8–3.3, and the creep activation energy values are in the range of 300–400 kJ/mol. After creep, a regular arrangement of ω{sub o} precipitations was observed in the β{sub o} region. The un-transformed β{sub o} phase, which remained in the ω{sub o} interval, was examined using high resolution transmission electron microscope (HRTEM). It is shown that the growth of ω{sub o} precipitations and the morphology of residual β{sub o} phases are related to the creep temperature and stress. Certain β{sub o} stabilizer elements, such as Nb, segregate into α{sub 2} plates and cause ω{sub o} precipitation during dissolution of α{sub 2} plates at high temperature. The interfacial structure between the ω{sub o} and α{sub 2} phases was studied in detail using HRTEM. Meanwhile, texture evolution and dynamic recrystallization of the γ phase were studied using electron backscatter diffraction (EBSD). Observations on the deformation structure also demonstrate that ω{sub o} precipitation acts as an obstacle inhibiting crack propagation and growth of the γ phase. The corresponding formation mechanism and possible effects on creep are discussed.

36 MATERIALS SCIENCE↗

Cold rolling texture evolution of TiB2 particle reinforced Al-based composites by Neutron Diffraction and EBSD analysis

Highlights: • Texture development of in-situ TiB{sub 2} particle reinforced Al matrix composites after cold rolling were characterized. • The sum of rolling texture volume fractions has been significantly reduced by the weak texture in particle deformation zone. • Recrystallization nuclei with the Cube and Rotated-Cube orientations were observed in the particle deformation zones. • Small TiB{sub 2} particles within Al grains kept the parallel relationship with surrounding matrix during the deformation. - Abstract: Texture development of particle-reinforced metal matrix materials (P-MMCs) has not been understood well, especially the effects of second-phase particles during the deformation. In this work, we have investigated the texture evolution of TiB{sub 2}/Al composites during cold rolling by Neutron Diffraction and EBSD analysis. Two forms of TiB{sub 2} particles influenced the texture evolution in different ways. The particle-clusters aggregated along grain boundaries led to a reduction of texture volume fraction; recrystallization nuclei with weak texture appeared around these particle-clusters. Small non-shearable TiB{sub 2} particles dispersed inside Al matrix contributed to strong Copper texture component at high strains; the individual particles rotated together with Al matrix during the deformation. These revealed effects of particles on the texture development in TiB{sub 2}/Al composites provide a reference for the texture control of P-MMCs.

36 MATERIALS SCIENCE↗

Effect of high content of manganese on microstructure, texture and mechanical properties of magnesium alloy

Highlights: • Extremely refined Mg-3.0Mn alloys are prepared by conventional extrusion process. • Mn addition can effectively weaken the basal texture of the alloys. • Strength, yield anisotropy and ductility have been obviously improved. - Abstract: In the present investigation, microstructure, texture and mechanical properties of Mg-3Mn alloys fabricated by hot extrusion process with the extrusion temperatures of 250 °C and 300 °C were investigated. The results revealed that the samples exhibited the refined microstructure and weakened basal texture. Refined microstructure of the samples was attributed to the dynamic precipitates suppressing the recrystallization grain growth during extrusion process. Weakened basal texture of the samples was explained as a result of particle stimulated nucleation (PSN) promoted by coarsened Mn precipitates altering the texture of extruded profiles during recrystallization by orienting the c-axis of grains at an angle that favors basal slip activity. As a result, the samples exhibited the high tensile elongation and good yield strength at room temperature.

36 MATERIALS SCIENCE↗

Microstructure evolution and mechanical properties of the compressively deformed AgInCd alloy during annealing treatment

Highlights: • The microstructure of AgInCd alloy during annealing treatment is investigated. • Nanoscale deformation twins are formed in the deformed AgInCd alloy. • Deformation twins are transformed into stacking faults by detwinning mechanism. • Annealing twins show higher thermal stability than deformation twins. - Abstract: The microstructure evolution and mechanical properties of the compressively deformed AgInCd alloy during annealing treatment have been investigated in the present study. In the deformed AgInCd alloy, many deformation markings are formed and these deformation markings are mainly composed of nanoscale deformation twins. The AgInCd alloy exhibits a significant work hardening capability because of the formation of deformation twins. The recrystallization temperature of the deformed AgInCd alloy is between 300 °C and 350 °C. In the AgInCd alloy annealed at 300 °C, the deformation twins are eliminated and a large number of dark strips consisting of stacking faults are presented in the un-recrystallized regions, indicating that the deformation twins are transformed into stacking faults by the detwinning mechanism. The annealing twins show higher thermal stability than the deformation twins. The strength and microhardness of the deformed AgInCd alloy gradually decrease with the increase of annealing temperature.

36 MATERIALS SCIENCE↗

Effect of non-axisymmetric arc on microstructure, texture and properties of variable polarity plasma arc welded 5A06 Al alloy

Highlights: • Variable polarity plasma arc welding of 5A06 Al alloy was carried out under the condition of non-axisymmetric arc. • Deformation bands formed in the weld joint were due to microstructural inhomogeneities. • Tensile fracture occurred along the deformation bands in the TZ/HAZ fusion boundary on the side of “lower arc”. • The weld zones are harder than the BM due to dislocation sub-structure, deformation bands and ultrafine subgrain. - Abstract: Microstructure, texture and mechanical properties in the weld joint of variable polarity plasma arc welding of 5A06 Al alloy under the condition of non-axisymmetric arc have been investigated. The weld joint are characterized by elongated structure in the base material (BM), the heat affected zone (HAZ) and the transition zone (TZ) and equiaxed structure in the fusion zone (FZ). Microstructure of the weld joint is asymmetrical and inhomogeneous leading to deformation bands. Deformation texture and recrystallization texture were developed in the weld zones. The FZ center was dynamic recrystallized due to severe deformation. Materials in the TZ have undergone dynamic recovery. The weld zones are harder than the BM due to dislocation sub-structure, deformation bands and ultrafine subgrains. Microhardness distribution was homogeneous in the regions without deformation bands. Tensile fracture occurred along the deformation bands on the side of “lower arc” exhibiting ductile fracture, while the BM is less ductile.

36 MATERIALS SCIENCE↗

Characterization of Alloy 600 joints exposed to a high-temperature supercritical-carbon dioxide environment

Highlights: • Diffusion-bond showed similar corrosion and carburization behavior as parent matrix. • Diffusion-bond line migrated due to the Cr-depletion induced recrystallization. • Alloy 182 fusion-weld showed larger weight gains with outer Mn-rich oxides. • The presence of SiO{sub 2} in chromia suppressed carburization at the oxide/matrix interface. • Despite larger weight gains, Alloy 182 fusion-weld showed negligible tensile property changes. - Abstract: Two types of Alloy 600 joints, such as diffusion-bonded joint and Alloy 182 fusion-weld, were exposed to supercritical-CO{sub 2} environment at 550 and 650 °C (20 MPa) for 1000 h. The diffusion-bond region showed similar oxidation characteristics as parent Alloy 600, but the migration of diffusion bond line below oxide layer was observed due to the Cr-depletion induced recrystallization. For Alloy 182 fusion-weld, outer Mn-rich oxides (Mn{sub 3}O{sub 4} and MnCr{sub 2}O{sub 4}) and a small amount of inner SiO{sub 2} mixed with chromia were formed due to high Mn and Si contents. The presence of SiO{sub 2} in chromia suppressed carburization at the oxide/matrix interface, which resulted in the formation of an amorphous C layer between the outer Mn-rich oxide and inner Cr-rich oxide. For Alloy 182 fusion-weld, tensile property changes after exposure to supercritical-CO{sub 2} environment were negligible.

36 MATERIALS SCIENCE↗

The effect of finish rolling temperature and tempering on the microstructure, mechanical properties and dislocation density of direct-quenched steel

Highlights: • The effect of thermomechanical treatment and tempering on direct-quenched steel has been studied. • Dislocation density of direct-quenched and tempered martensite is evaluated using both TEM and Williamson-Hall method. • Statistical analysis has been performed to study the effect of different factors on toughness of direct-quenched martensite. - Abstract: A unique batch tempering treatment for industrial scale direct-quenched steel coils has been studied using laboratory simulations. The tempering treatment was non-isothermal with slow heating to 570 °C and slow cooling to simulate the tempering of large steel coils. The paper presents the effect of finishing rolling temperature (FRT) relative to the non-recrystallization temperature (T{sub NR}) and the effect of long time tempering on the microstructure, dislocation density and mechanical properties of direct-quenched coiled strips. Conditioning austenite below the recrystallization stop temperature resulted in a finer effective grain size distribution, which correlated strongly with the impact toughness of the final product. Furthermore low finish rolling temperature resulted in partially ferritic microstructures while higher finishing rolling temperatures led to mixtures of bainite and martensite. Dislocation densities determined with TEM and XRD showed somewhat different trends regarding the effect of tempering: intra-lath dislocation density, as measured with TEM, showed a statistically significant drop in only one case, while XRD analysis indicated a drop in all cases. Furthermore, no significant correlation between finishing rolling temperature and dislocation density existed in XRD studies. The XRD results indicate that the decrease in dislocation density corresponds to about 100 MPa lower dislocation strengthening. However, precipitation hardening and potential internal micro stress relief compensates this as yield strength remains unchanged or even increases during tempering.

36 MATERIALS SCIENCE↗

High-temperature deformation behavior and microstructural characterization of high-Mn bearing titanium-based alloy

Highlights: • The hot deformation behavior of a biomedical low-cost Ti-10Mn alloys was studied. • The flow curves of the alloy display periodic serrations attributed to dynamic strain aging. • Mn alloying increases the activation energy to 243 kJ/mol compared to pure Ti. • The dynamic recovery is more effective than dynamic recrystallization at hot deformation. - Abstract: Ti-Mn alloys exhibit an excellent potential for biomedical applications as well as structural engineering applications, especially in the aerospace industry. In order to control and enhance grain structure during the manufacturing of Ti-Mn alloys and thereby help to enhance mechanical properties such as strength and toughness, we studied the hot-deformation behavior of βTi-10Mn alloys. Isothermal compression tests were conducted in the strain rate range of 0.01–10 s{sup −1} and temperatures in the range of 850–1000 °C using a Gleeble thermomechanical simulator. High-temperature flow stress curves exhibited discontinuous yielding and pronounced periodic serrations without any strain hardening during compression straining of these alloys. Such peculiar behavior of this alloy is due to active dynamic strain aging in its β-bcc structure. Metallographic observations by electron-backscattered diffraction (EBSD) analysis revealed that dynamic recovery (DRV) is more active than continuous dynamic recrystallization (CDRX) when the alloy is deformed at high strain rates, i.e. higher than 1 s{sup −1}. Furthermore, the constitutive behavior of the alloy was modeled and the apparent hot-deformation activation energy of the alloy was estimated to be 243 kJ/mol, which is ~60% higher than the self-diffusion energy in pure titanium.

36 MATERIALS SCIENCE↗

Optimization of hot workability and microstructure control in a 12Cr-10Ni precipitation hardenable stainless steel: An approach using processing maps

Highlights: • Deformation processing map was developed for a 12Cr10Ni precipitation hardenable martensitic stainless steel and optimized hot working parameters were suggested to obtain defect free products. • The ‘stable’ domain of the processing maps were correlated to the dynamic recrystallization in the austenite phase and further confirmed by detailed microstructural investigations. • The DRx domain showed a refinement of the martensite packet size and of the prior transformation austenite grain size, essential to obtain the desired mechanical properties. - Abstract: Optimization of hot working parameters and corresponding microstructure control were explored in a 12Cr-10Ni precipitation hardenable martensitic stainless steel. From hot compression tests, 1073–1373 K (800°–1100 °C) and five (0.001–10 s{sup −1}) different strain rates, processing maps were developed, and various domains of microstructure evolution (in the austenite phase) were identified. The stable domain of the processing maps appeared to indicate dynamic recrystallization (DRx) in the austenite phase: as evident by the appearance of inflection point in the strain hardening rate versus flow stress plots. The suspected DRx domain was further confirmed by detailed microstructural investigations of the respective water-quenched specimens. The DRx domain showed a refinement of the martensite packet size and of the prior transformation austenite grain size. The later was shown with optical microstructure and reconstructed (modelled) microtexture data of the prior austenite grains. Additionally, the DRx domain showed a significant difference in activation energy as estimated from appropriate constitutive modelling.

36 MATERIALS SCIENCE↗